Haier HSU-12HQA03, HSU-12HQA03R2 Operation Manual

OPERATION MANUAL

Please read this operation manual before using the air conditioner

HSU-12HQA03/R2(DB)

0010538206

7

2
3

6

8

Cautions

Parts and functions
Operation
Maintenance

Trouble shooting

Contents

1

Outdoor Unit

4

Loading of the battery

1

2

3

4

Parts and Functions

Indoor Unit

OUTLET

INLET

CONNECTING PIPING AND ELECTRICAL WIRING

DRAIN HOSE

Remote controller

Remove the battery cover;

Load the batteries as illustrated.

2 R-03 batteries, resetting key

(cylinder);

Be sure that the loading

is in line with th

e" + "/"-";

Load the battery,then put on the cover again.

Clock set

Press CLOCK button, "AM" or "PM" flashes.
Press or to set correct time. Each press

change quickly.

After time setting is confirmed,press SET,

"AM "and "PM" stop flashing,while clock starts working.

or decrease 1min. If the

button is kept pressed,time will

will increase

The distance between the signal transmission head and the rece­iver hole should be within 7m without any obstacle as well.

When electronic-started type fluorescent lamp or change-over

wireless telephone is installed in the

ver is apt to be disturbed in receiving

the signals,

so the distance to the indoor unit should be sho

rter.

type fluorescent lamp or
room, the recei

Note:

Full display or unclear display during operation indicates the

ries have been used up.

Please change batteries.

If the remote controller can't run normally during operation, please

reload several minutes later.

batte

remove the batteries and

Remove the batteries in case unit won't be in usage for a long period.

If there are any display

after taking-out, just need to press reset key.

Hint:

Actual indoop unit may vary from the one shown

in the manual, according to the product purchased.

Inlet
grille

Air Purifying

Outlet

Horizontal flap

(adjust up and down air flow

Don't adjust it manually)

(adjust left and

ow)

Vertical blade

Filter

Anion

generator

(inside)

right air fl

Inlet

1

2

3

31. CODE

2

TEMP display

Display board

COOL: blue

AUTO: white

HEAT: red

DRY: cyan

FAN: yellow

: green

Nano-Aquo

Aureole

Display mode，the aureole display different
colour when setting different function

Nano-Aquo
Generator
（inside）

The following functions and related displays are not available：

31

30

28

19

Operation mode

AUTO

FAN

COOL DRY

Remote controller

HEAT

3. TIMER button

4. CLOCK button

5. SLEEP button

6. MODE button

7. HOUR button

8. HEALTH button

9. ON/OFF button

10. TIMER ON display

11. FAN SPEED display

LOW HI

MED AUTO

12. LOCK displ

ay

13. SWING display

14. SLEEP display

15. HEALTH display

16. Operation mode display

18. POWER/SOFT display

19. Left/right air flow display

20. TEMP display

21. TIMER OFF display

22. TIMER display

23. TEMP button

24. FAN SPEED button

25. HEALTH AIRFLOW button

26. SWING UP/DOWN button

27. SWING LEFT/RIGHT button

28. SET button

29. POWER/SOFT button

17.Singal sending display

30

.

LOCK

button

When the remote controller

RESET button

appears abnormal,use a
sharp pointed article to press
this button to reset the remote
controller controller normal.

1

.

2.LIGHT button

Control the lightening and
extinguishing of the indoor
LED display board.

If pressed, the other buttons will be
disabled. Press it once again, lock
will be cancelled.

31

Used to select CODE A or B with a
press, A or B will be displayed on LCD.
Please select A without special
explanation.

Operation

AUTO COOL DRY FAN HEAT

2.Select operation mode

Press MODE button. For each press, operation mode
changes as follows:
Remote controller:

1. Unit start

Press ON/OFF on the remote controller, unit starts.

Base Operation

Remote controller

Air Flow Direction Adjustment

Vertical flap

Pos.1

Pos.2

Pos.3

Pos.4

Pos.5

Pos.6

(Auto swing)

1.Status display of air flow

When restart after remote turning off, the remote

memorize the previous

2.Left and right air flow adjustment

Cautions:

When adjusting the flap by hand,turn off the unit.
When humidity is high,condensate water might occur

adjusted to left or

It is advisable not to keep horizontal flap at downward
position for a long time in COOLor DRY
otherwise, condensate water might occur.

Emergency Operation:

temperature is below 16

o

C, do not use it in the

Test operation:

Use this switch in the test operation when the room

normal operation.

your finger from the switch: the cooling

Continue to press the test operation

switch for more than 5 seconds . After

you hear the "Pi" sound twice,

release

Test ope ration switch is the same as emergency switch.

operation starts with the air flow speed "Hi".

Emergency operation and test operation

Use this operation only when the remote controller
is defective or lost.

When the emergency operation switch is
pressed,the" Pi "sound is heard once

, which

the start of this operation.

In this operation, the system automatically selects

the

operation modes

,cooling or fan or heat,

according to the room temperature.

.

It is not possible to operate in dry mode.

Room

temperature

Operation
mode

Designated
temperature

Timer

mode

Air flow

ABOVE 24

O

C

BELOW 24

O

C

COOLING

HEAT

2

4

O

C

2

4

O

C

NO

NO

AUTOMATIC

AUTOMATIC

(C

ooling only uint）

Room temperature

Operation

mode

Designated
temperature

Timer
mode

Air flow

BELOW 2

4

O

C

FAN

2

4

O

C

NO

AUTOMATIC

at air outlet if all vertical louvers are

right.

mode ,

controller will automatically

Note:

set swing position.

means

Operation

Mode

AUTO

Remote

Controller

Note

COOL

DRY

HEAT

FAN

In DRY mode, when room temperature becomes
lower than temp.setting+2

o

C, unit will run

intermittently at LOW speed regardless of FAN

Under the mode of auto operation, air conditioner

will automatically select Cool or Heat operation
according to room temperature. When FAN is set
to AUTO, the air conditioner

automatically adjusts

temperature.

the fan speed according to room

In FAN operation mode , the unit will not operate in

COOL or

HEAT mode but only in

FAN mode ,

AUTO is not available in

FAN mode.

And temp.

setting is disabled. In FAN mode, sleep operation

setting.

is not available.

Pi

emergency
operation
switch

test operation

switch

Pi

Pi

Press FAN button. For each press, fan speed

follows:

Remote controller:

Press button

Every time the button is pressed, temp.setting
increase 1

o

C,if kept depressed, it will increase

rapidly

Every time the button is pressed, temp.setting

decrease 1

o

C,if kept depressed, it will

decrease rapidly

Select a desired temperature.

4.Fan speed selection

3.Select temp.setting

Air conditioner is running under displayed fan speed.
When FAN is set to AUTO, the air conditioner
automatically adjusts the fan speed according to room
temperature.

LOW

MED

HI

AUTO

/

changes as

3

1

4

2

Pos.1

Pos.2

Pos.3

Pos.4

Pos.5

Pos.6

Pos.7

Pos.8

For each press of button, remote controller
displays as follows :

remote controller: