Haier HSU12XH7-G, HSU12XH7, HSU09XH7, HSU09XH7-W, HSU12XH7-W User Manual
...
Installation Manual of Room Air Conditioner
Preparation
Necessary Tools for Installation
Torque wrench
Hammerƽ
Nipperƽ
Hacksawƽ Pipe cutterƽ
Hole core drillƽ Flaring toolƽ
Spanner(17,19 and 26mm)ƽ Knifeƽ
Gas leakage detector orƽ
soap-and-water solution
ƽ
(17mm ,2 2mm, 26m m)
Measuring tapeƽ
Reamerƽ
Power Source
ƽ
Before inserting power plug into receptacle, check the voltage withou
The power
Install an exclusive branch circuit of the power.
ƽ
A receptacle shall be set up in a distance where the power cable can be
ƽ
reached.
source is the same as the
Donotextendthecablebycuttingit.
corresponding name plate.
Drawing for the installation of indoor and outdoor units
The models adopt HCFC
more than 5cm
more than
10cm
free refrigerant R410A
Indoor Unit - Select a plocation that is
Robust not causing vibration, where the body can be supported sufficiently.
ƽ
Not affected by heat or steam generated in the vicinity, where inlet and outlet of the
ƽ
unit are not disturbed.
Possible to drain easily, where piping can be connected with the outdoor unit.
ƽ
Where cold air can be spread in a room evenly.
ƽ
Nearby a power receptacle. (Refer to drawings).
ƽ
Place where the distance of more than lm from televisions, radios, wireless apparatuses
ƽ
and fluorescent lamps can be left.
In the case of fixing the remote controller on a wall, place where the indoor unit can
ƽ
tfail.
Attention must be paid to
the rising up of drain hose
receive signals when the fluorescent
Outdoor Unit - Select a plocation that is
Not less affected by rain or direct sunlight and is sufficiently ventilated.
ƽ
ƽ
Strong enough to bear the unit, where vibration and noise are not increased.
Place, where discharged wind and noise do not cause a nuisance to the neighbors.ƽ
Place, where a distance markedƽ
Selection of Installation Place
lamps in the room are lightened.
isavailableasillustratedintheabovefigure.
Q
Optional parts for piping
Non-adhesive tape
A
Adhesive tape
B
Saddle (L.S) with screws
G
C
Connecting electric cable
D
forindoorandoutdoor
E
Drain hose
F
Heating insulating material
Piping hole cover
G
Arrangement of piping
directions
Rear left
Left
Below
The marks from to
ƽ
G
in the figure are the
parts numbers.
Thedistancebetween
ƽ
theindoorunitandthe
floor should be more
than 2m.
Rear
right
Right
A
more than
more than 10cm
60cm
more than 10cm
A
more than
10cm
more than15cm
Floor fixing dimensions of the
outdoor unit (Unit:mm)
F
113.5
184
043
0
83
For 18K
C
113.5
633
For 24K
184
580
Fixing of outdoor unit
Fix the unit to concrete or blockƽ
D
E
with bolts (10mm) and nuts firmly
and horizontally.
When fitting the unit to wall
ƽ
surface, roof or rooftop, fix
a supporter securely with nails
or wires in consideration of
earthquake and strong wind.
If vibration may affect the
ƽ
house, fix the unit by attaching a
vibration-proof mat.
Please be subject to the actual product purchased , the above picture is just for your reference.
Read this manual before installation
Explain sufficiently the operating means to the user according to this manual.
NO.0010519373
Accessory parts
Remote controller (1)
R-03 dry battery (2)
Mounting plate (1)
Plastic cap (4)
Ø4X25 Screw
(4)
Drain hose (1)
Cushion (4)
Drain-elbow (1)
Pipe supporting plate (1)
Selectionofpipe
Type
Liquid pipe (Ø)
Gas pipe (Ø)
NOTE˖The thickness of the pipe must be 0.8mm at least.
For 18K
6.35mm(1/4”)
12.7mm(1/2”)
For 24K
9.52 mm(3/8”)
15.88 mm(5/8”)
Indoor unit
FittingoftheMountingPlateand
Whenthemountingplateisrstxed
1. Carry out, based on the neighboring pillars or lintels, a
to be xed against the wall, then temporarily fasten the plate with one steel nail.
2. Make sure once more the proper level of the plate, by
weight from the central top of the plate, then fasten securely the plate with the
attachment steel nail.
3. Find the wall hole location A using a measuring tape
PositioningofthewallHole
proper leveling for the plate
hanging a thread with a
1. Insert the drain hose into the dent of heat insulation materials of indoor unit.
2. Insert the indoor/outdoor electric cable from backside of indoor
outonthefrontside,thenconnect them.
3.Coatthearingsealfacewithrefrigerantoilandconnect pipes.
Cover the connection part with heat insulation materials, cover with adhesive tape.
Heat insulation
Lid for right
piping
Lid for under piping pipe
Fix with adhesive tape
ƽ
Indoor/outdoor electric cable and drain hose must be bound with refrigerant
piping with protecting tape.
Lid for left piping
material
Drain hose
unit, and pull it
Indoor/outdoor electric cable
Piping
Pipe supporting
plate
[Otherdirectionpiping ]
ƽ
Cut away, with a nipper, the lid for piping according to the piping direction and
then bend the pipe according to the position of wall hole. When bending, be
careful not to crash
ƽ
Connect beforehand the indoor/outdoor electric cable,
connected to the heat insulation of connecting part specially.
pipes.
andthenpulloutthe
Fixing the indoor unit body
Hang the unit body securely onto the upper notches of the
ƽ
mounting plate. Move the body from side to side to verify
Inordertoxthebodyontothemountingplate,holdup
ƽ
thebodyaslantfromtheundersideandthenputitdown
perpendicularly.
mounting plate
A=150mm
When themountingplateisxedside barandlintel
Fix to side bar and lintel a mounting bar, Which is separately sold, and then
ƽ
fasten the plate to the xed mounting bar.
Refertothepreviousarticle, “ Whenthemountingplateis
ƽ
position of wall hole.
Making a Hole on the Wall and Fitting the Piping Hole Cover
Make a hole of 70 mm in diameter, slightly descending to outside the wall.
ƽ
Install piping hole cover and seal it off with putt y after installation
ƽ
Wall hole
Ø70mm
Indoor side
(Section of wall hole) Piping hole pipe
Installation of the Indoor Unit
Thickness of wall
G
Outdoor side
90mm
rst xed “, for the
70mm
Unloading of indoor unit body
When you unload the indoor unit, please use
ƽ
your hand to raise the body, then lift the
bottom of the body outward slightly
and lift the unit until it leaves the
mounting plate.
mounting plate
agraffe
Connecting the indoor/outdoor Electric Cable
Removing the wiring cover
Remove terminal cover at right bottom corner of indoor unit, then takeƽ
off wiring cover by removing its screws.
When connecting the cable after installing the indoor unit
1. Insert from outside the room cable into left side of the wall
hole,inwhichthepipehasalreadyexisted.
2. Pull out the cable on the front side, and connect the cable
making a loop.
When connecting the cable before installing the indoor unit
Insert the cord from the back side of the unit, then pull it out on the front side.
ƽ
Fasten the unit wire harness to the conduit holder using the lock nut.
ƽ
Position the conduit holder to its original state using screw.
ƽ
Drawingofpipe
[Rearpiping ]
Drawpipesandthedrainhose,thenfastenthemwiththeadhesivetape
ƽ
[Left·Left-rear piping ]
ƽ
In case of left side piping, cut away, with a nipper, the lid for left piping.
In case of left-rear piping, bend the pipes according to the piping direction to
ƽ
the mark of hole for left-rear piping which is marked on heat insulation materials.
2
Conduit holder
When connecting the cable, conrm the terminal number of indoor and
Note
outdoor units carefully. If wiring is not correct, proper operation can not
be carried out and will cause defect.
Cut the 6 slit sear
Loading...