Haier HSU09XCK, HSU24VCK Operation Manual

Please read this operation manual before using the air conditioner.

●

Keep this operation manual for future reference.

SPLITTYPEROOMAIRCONDITIONER OPERATION MANUAL

0010536241

HSU18VCK-G HSU24VCK-G

HSU09XCK-G HSU12XCK-G

1 2

5 6

PARTS AND FUNCTIONS OPERATION MAINTENANCE

TROUBLE SHOOTING

CAUTIONS

Contents

8 9

Índice

PRECAUCIONES

COMPONENTES Y FUNCIONES FUNCIONAMIENTO MANTENIMIENTO

RESOLUCIÓN DE PROBLEMAS

15 16

20 21

Table des matières

AVERTISSEMENTS

PIÈCES ET FONCTIONS

MAINTENANCE

DÉPANNAGE

UTILISATION

Outdoor Unit



Loading of the battery

1 2



Parts and Functions

Indoor Unit

OUTLET

INLET

CONNECTING PIPING AND ELECTRICAL WIRING

DRAIN HOSE

Remote controller

Remove the battery cover;

Load the batteries as illustrated.

2 AAA batteries, resetting key

(cylinder);

" + "/"-";

Load the battery,then put on the cover again.

Note:

Please be subject to the actual produce purchased the above picture is just from your reference

Air Purifying Filter

(inside)

Inlet

Inlet grille

Outlet

(adjust left and

Vertical blade

right air flow)

Display board

Horizontal flap

(adjust up and down air flow.

Don't adjust it manually)

Emergency

Switch

Hint: Remove the batteries in case won't be in use for a long period. If there is any display after taking-out, just press reset key.







1. Mode display

2. Signal sending display

4. FAN SPEED display

5. LOCK display

6. TIMER OFF display TIMER ON display

7.TEMP display

15. LOCK button

Used to lock buttons and LCD display

24. RESET button When the remote controller appears abnormal, use a sharp pointed article to press this button to reset

21. HOUR button

Operation mode

AUTO FANCOOL DRY

Remote controller

15 16

Control the lightening and extinguishing of the indoor LED display board.

9. QUIET button

10. COOL button

11. AUTO button

12. FAN button

13. TIMER button

14. HEALTH button

16. LIGHT button

17. POWER ON/OFF button

18. DRY button

19. TEMP button

20. SWING button

22. EXTRA FUNCTION button

23.CANCEL/CONFIRM button Function: Setting and cancel to the

timer and other additional functions.

3. SWING display

LO MED HI

AUTO

Display circulated

Operation mode

Remote controller

QUITE

POWER

SLEEP

HEALTH

Healthy function is not available for some units.

the remote.

Be sure battery polarity is correct

The distance from the remote to the receiver should be less than 23 feet (7 meters) with no obstructions.

Fluorescent lights or cordless telephones will reduce the range of the remote.

If the display is dim the remote batteries may need to be replaced.

Remote malfunctions can sometimes be corrected by removing the batteries for a few minutes and then replacing them.

Function: Air sending--- Healthy airflow position1--- Healthy airflow position 2 --- Restore the original

--- Right & left air airflow

--- A-B yard--- Sleeping--- Refresh air

(reserved function)

--- Power ---

Fahrenheit/Celsius mode conversion

Additional functions display

flap position

Operation

Air Flow Direction Adjustment

Press FAN button. For each press, fan speed

follows:

Remote controller:

Press

button

Every time the button is pressed, temp.setting increase 1

C,if kept depressed, it will increase

rapidly

Every time the button is pressed, temp.setting

decrease 1

C,if kept depressed, it will

decrease rapidly

Select a desired temperature.

3.Fan speed selection

2.Select temp.setting

Air conditioner is running under displayed fan speed. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature.

1. Unit start

Press ON/OFF on the remote controller, unit starts.



Base Operation

Remote controller

1.Status display of air flow

When restart after remote turning off, the remote

return to the previous

Move the vertical blade by a knob on air to adjust left and right direction referring to the figure below.

2.Left and right air flow adjustment

(manual)

Cautions:

When adjusting the flap by hand,turn off the unit.

When humidity is high,condensate water might occur

adjusted to left or

It is advisable not to keep horizontal flap at downward position for a long time in COOLor DRY

otherwise, condensate water might occur.

conditioner

Emergency operation and test operation

at air outlet if all vertical louvers are

right.

mode ,

controller will automatically

Note:

set swing position.

changes as

'

AUTO

Note

COOL

DRY

FAN

In DRY mode , when room temperature becomes lower than temp.setting+2

C, unit will run

intermittently at LOW speed regardless of FAN

Under the mode of auto operation , air conditioner will automatically select Cool operation according to

room temperature.

conditioner automatically adjusts the fan speed according

When FAN is set to AUTO the air

to room temperature.

In FAN operation mode , the unit will not operate in COOL mode but only in FAN mode, AUTO is not available in FAN mode. And temp.setting is disabled. In FAN mode, sleep operation is not available.

setting.

test operation

switch

Emergency Operation:

Use this operation only when the remote controller is defective or lost, and with function of emergency running, air conditoner can run automatically for a while. When the emergency operation switch is pressed, the unit beeps once, which means the start of this operation.

When power switch is turning on for the first time and emergency operation starts, the unit will run automatically in the following modes:

Room temperature

Designated temperature

Timer mode

Fan

speed

Operation

mode

Above 23oC 26oC AUTO COOL

emergency

operation switch

It is impossible to change the settings of temp. and fan speed,It is also not possible to operate in timer or dry mode.

is below 16

C, do not use it in the normal operation.

Test operation:

Use this switch in the test operation when the room temperature

from the switch: the cooling operation

Continue to press the test operation

switch for more than 5 seconds.After

you hear two beeps, release your finger

starts with the air flow speed "Hi".

Under this operation mode,the fan motor of indoor unit will run in high speed.







COOL/DRY:

LOW

MED HI

AUTO

Display circulated

Remote Controller Icon

Operation Mode

Test operation switch is the same as emergency switch.

Operation

Sleep Operation

If the wind speed is high or middle before setting for the sleep, set for lowing the wind speed after sleeping. If it is low wind, no change.

4.Set the wind speed change when sleeping

Operation Mode

1. In COOL,DRY mode

SLEEP operation starts SLEEP operation stops

Approx.6hrs

1 hr

Rises 1

Temp.setting

Unit stop

In COOL, DRY mode

1 hr

In AUTO mode

3. In FAN mode

It has no SLEEP function.

Note

When TIMER function is set, the sleeping function can’t be set up .After the sleeping function is set u

TIMER function, the sleeping function will be cancelled; the machine will be in the state of

timing-on.

1 hours after SLEEP mode starts,temp.will become

higher than temp.setting.After another 1 hours,

temp.risesby 1 futher .The unit will run for further 6 hours then stops Temp. is higher than temp.setting so that room temperature won’t be too low for your sleep.

The unit operaters in corresponding sleep mode adapted to the automatically selected operation mode.

if user resets

POWER/QUIET Operation

Press button to enter additional options, when cycle display to , will flash. And then press enter to sleep function.

(1)

POWER Operation

(2)

QUIET Operation

Note ˖

When you need rapid heating or cooling, you can use this function.

You can use this function when silence is needed for rest or reading.

During POWER operation, in rapid COOL mode ,

the room

will show inhomogeneous temperature distribution.

Long period QUIET operation will cause effect of not too cool or not too warm.

Press QUIET button, the remote controller will show , and then achieve to the quiet function. Press again this QUIET button , the quiet function will be cancelled.

Press button to enter additional options, when cycle display to , will flash，and then press ,enter to power function. When cancel the function, please enter additional options again and to cancel power function.

Operation

1.After unit starts, select your desired operation mode.

2.Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows:

Remote controller:

Then select your desired TIMER mode (TIMER ON or TIMER OFF or TIMER ON-OFF). " "or " "will flash.

Timer On/Off On-Off Operation

Healthy airflow Operation

1.Press to starting

Setting the comfort work conditions.

2.The setting of healthy airflow function

Note:

1.After setting the healthy airflow function, the position

grill is fixed.

3.In cooling and dry, using the air conditioner for a long time under the high air humidity, condensate water may occur at the grille .

Notice: Do not direct the flap by hand. Otherwise, the grille will run incorrectly. If the grille is not run correctly, stop

for a minute and then start, adjusting by remote controller.

2.In cooling, it is better to select the

mode.

BLANK

TIMER ON TIMER OFF TIMER ON-OFF

3.Press / button to set time.

It can be adjusted within 24 hours.

Hints: After replacing batteries or a power failure happens, time setting should be reset.

According to the Time setting sequence of TIMER ON or

TIMER OFF, either Start-Stop or Stop-Start can be achieved.

3.The cancel of the healthy airflow function

TIMER OFF-ON

0.5h

0.5h 0.5h

0.5h

Press the button for each time, setting time in the first 12 hours increased by 0.5 hour every time, after 12 hours,increased by 1 hour every time.

Press the button for each time, settiing time in the first 12 hours decreased by 0.5 hour every time, after 12 hours,decreased by 1 hour every time.

After adjust the time,press button and confirm the time ON or OFF button will not flash any more.

4.Confirm timer setting

5.Cancel timer setting Press the timer button by times until the time display eliminated.

Press button to enter additional options,Press this button continuously, the louvers location will cycle between in the following three locations, to choose the swing location

what you needed,and then press button to confirm.

Press button to enter additional options,Press this button continuously, the louvers location will cycle between in the following three locations again,and then press button to cancel.

Healthy airflow upwarder

Healthy airflow downwarder

Present position

Maintenance

Setting of proper room temperature

Close doors and windows during operation

If the unit is not to be used for a long time, turn off the power supply main switch.

Use the timer effectively

Use the louvers effectively

Do not block the air inlet or outlet

Proper

temperature

During cooling operation prevent the penetration of

direct sunlight with

curtain or blind

OFF

Remote Controller Indoor Body

1.Open the lnlet Grille

2.Detach the standard air filter

3.Attach Air Purifying Filter

4.Attach the standard air filter

(Necessar

y installation)

5.Close the Inlet Grille

Close the Grille surely

Slide the knob slightly up

ward to

release the filter, then withdraw it.

Put air purifying filter appliances into the

right and left filter frames.

Detach old Air Purifying Filter

NOTE:

The photocatalyst air purifying filter will be solarized in fixed time. In normal family,

it will be solarized every 6 months.

Prop up the inlet grille by with a grille

ATTENTION:

Please keep the bacteria-killing medium air purifying filter in

avoid long time directly sunshine

when you stop using it,or its ability of sterilization will

reduced.

The bacteria-killing medium air purifying filter will be used for a long time,no need for replacement. But in the period of using them ,you should remove the dust frequently by

support located in the right side of

the indoor unit.

using vacuum cleaner or flaping them lightly,otherwise ,

its performance will be affected.

the cool and dry conditions

For Smart Use of The Air Conditioner

Replacement of Air Purifying Filter

The white side of the photocatalyst air purifying filter face outside,and the black side face the unit The green

side of the bacteria-killing medium air purifying filter face outside,and the white side face the unit.

Do not usewater,wipe the controller with a dry cloth.Do not use glass

cleaner or chemical cloth.

wipe the air conditioner by using a soft and dry cloth.For serious stains,

use a neutral detergent diluted with water.Wring the water out of the cloth before wiping,then wipe off the detergent completely.

Air Filter cleaning

Open the inlet grille by pulling it upward.

Remove the filter.

Clean the filter.

Attach the filter.

Close the inlet grille.

Push up the filter's center tab slightly until it is

from the stopper, and remove the filter do

wnw

ard.

Use a vacuum cleaner to remove dust, or wash the filter with water.After washing, dry the filter completely in the shade.

Attach the filter correctly so that the "FRONT" indication

facing to the front.Make sure that the filter is

fixed behind the stopper.If the right

attached correctly, that

Do not use the following for cleaning

Gasoline,benzine, thinner or cleanser

damage the coating of the unit.

Hot water over 40

C(104OF) may

discoloring or deformation.

Once every two weeks

cause

released

completely

and left filters are not

may cause defects.

the power supply cord and so on.

Do not install in the place where there is any

possibility of inflammable gas leakage around the unit.

3.Do not get the unit exposed

to vapor or oil steam.

Cautions

Do not attempt to install the air conditioner by yourself because improper works

Connect the earth cable.

earthing

WARNING

When abnormality such as burnt-small found, immediately stop the operation button and contact sales shop.

OFF

Use an exclusive power source with a circuit breaker

ENFORCEMENT

Connect power supply cord to the outlet completely

Use the proper voltage

Do not use power supply cord in a bundle.

Take care not to damage

the power supply cord.

1.Do not use power supply cord extended or connected in halfway

STRICT

ENFORCEMENT

STRICT

ENFORCEMENT

PROHIBITION

Do not start or stop the

operation by disconnecting

Do not channel the air flow directly at people, especially at infants or the aged.

Do not try to repair or reconstruct by yourself.

Do not use for the purpose of storage of food, art work, precise equipment, breeding, or cultivation.

CAUTION

Take fresh air occasionally especially when gas appliance is running at the same time.

PROHIBITION

STRICT

ENFORCEMENT

Do not operate the switch with wet hand.

PROHIBITION

Do not install the unit near a fireplace or other heating apparatus.

Check good condition of the installation stand

Do not pour water onto the unit for cleaning

PROHIBITION

Do not place animals or plants in the direct path of the air flow

Do not place any objects on or climb on the unit.

Do not place flower vase or water containers on the top of the unit.

Do not insert objects into the air inlet or outlet.

PROHIBITION

STRICT ENFORCEMENT

Check proper installation of the drainage securely

WARNING

This system should be installed by a qualified HVAC professional.

may cause fire, water leakage, personal injury or cleath.

+ 16 hidden pages

Haier HSU09XCK, HSU24VCK Operation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual