How it Works
Haier
Loading...
HSU-09RC03-R2-DB
User Manual
27 pgs1.6 Mb0

Haier HSU-09RC03-R2-DB User Manual

SPLIT TYPE ROOM AIR CONDITIONER
OPERATION MANUAL
HSU-09RC03/R2(DB) HSU-12RC03/R2(DB) HSU-18RC03/R2(DB) HSU-22RC03/R2(DB)
Please read this operation manual before using the air conditioner.
Cautions
Disposal of the old air conditioner
Before disposing an old air conditioner that goes out of use, please make sure it's inop­erative and safe. Unplug the air conditioner in order to avoid the risk of child entrapment.
Safety Instructions and Warnings
Before starting the air conditioner, read the information given in the User's Guide caref­ully. The User's Guide contains very impor­tant observations relating to the assembly, operation and maintenance of the air conditioner.
The manufacturer does not accept respon­sibility for any damages that may arise due to non-observation of the following instruction.
Damaged air conditioners are not to be put into operation. In case of doubt, consult your supplier.
Use of the air conditioner is to be carried out in strict compliance with the relative instructions set forth in the User's Guide.
Installation shall be done by professional people, don't install unit by yourself.
Disposal of the packaging of your new air conditioner
All the packaging materials employed in the package of your new air conditioner may be disposed without any danger to the environment.
The cardboard box may be broken or cut into smaller pieces and given to a waste paper disposal service. The wrapping bag made of polyethylene and the polyethylene foam pads
contain no fluorochloric hydrocarbon.
All these valuable materials may be taken to a waste collecting center and used again after adequate recycling.
Consult your local authorities for the name and address of the waste materials collecting centers and waste paper disposal services nearest to your house.
For the purpose of the safety,the air con­ditioner must be properly grounded in acco­rdance with specifications.
Always remember to unplug the air conditioner before openning inlet grill. Never unplug your air conditioner by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet.
All electrical repairs must be carried out by qualified electricians. Inadequate repairs may result in a major source of danger for the user of the air conditioner.
Do not damage any parts of the air conditioner that carry refrigerant by piercing or performating the air conditioner's tubes with sharp or pointed items, crushing or twisting any tubes, or scraping the coatings off the surfaces. If the refrigerant spurts out and gets into eyes, it may result in serious eye injuries.
1
Cautions
Do not obstruct or cover the ventilation grille of the air conditoner.Do not put fingers
6. The waste battery should be disposed
properly. or any other things into the inlet/outlet and swing louver.
7. The appliance is not intended for use
by young children or infirm persons
Do not allow children to play with the air conditioner.In no case should children be allowed to sit on the outdoor unit.
without supervision.
8. Young children should be supervised
to ensure that they do not play with
the applience.
Specifications
The refrigerating circuit is leak-proof.
The machine is adaptive in following situation
9.Please employ the proper power plug,
which fit into the power supply cord.
10 .The power plug and connecting cable
must have acquired the local attestation.
1.Applicable ambient temperature range:
Cooling
Heating
Indoor
Outdoor
Indoor
Outdoor
Maximum:D.B/W.B Minimum:D.B/W.B
Maximum:D.B/W.B Maximum:D.B
Maximum:D.B Maximum:D.B
Maximum:D.B/W.B Minimum:D.B/W.B
32oC/23oC 18oC/14oC
43oC/26oC 18oC
27oC 15oC
24oC/18oC
-7oC/-8oC
Outdoor
(INVERTER)
Maximum:D.B/W.B Minimum:D.B/W.B
24oC/18oC
-15oC
2. If the power supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person.
3. If the fuse of indoor unit on PC board is broken,please change it with the type of T. 3.15A/ 250V. If the fuse of outdoor unit is broken,change it with the type of T.25A/250V
4. The wiring method should be in line with the local wiring standard.
5. After installation, the power plug should be easily reached.
2
Cautions
Safety Instruction
Please read the following Safety Instructions carefully prior to use.
The instructions are classified into two levels, WARNING and CAUTION according to the seriousness of possible risks and damages as follows. Compliance to the instructions are strictly required for safety use.
Installation
WARNING
Please call Sales/Service Shop for the Installation.
Do not attempt to install the air conditioner by yourself because improper works may cause electric shock, fire, water leakage.
lnstallation in a inadequate place may cause accidents. Do not install in the following place.
CAUTION
Connect the earth cable.
earthing
Do not install in the place where there is any possibility of inflammable gas leakage around the unit.
PROHIBITION PROHIBITION
Do not get the unit exposed to vapor or oil steam.
3
Check proper installation of the drainage securely
STRICT ENFORCEMENT
Cautions
When abnormality such as burnt-small found, immediately stop the operation button and contact sales shop.
WARNING
Use an exclusive power source with a circuit breaker
OFF
Connect power supply cord to the outlet completely
STRICT
ENFORCEMENT
Do not use power supply cord in a bundle.
PROHIBITION
Do not start or stop the operation by disconnecting the power supply cord and so on.
PROHIBITION
Do not use for the purpose of storage of food, art work, precise equipment, breeding, or cultivation.
ENFORCEMENT
Use the proper voltage
Take care not to damage
the power supply cord.
Do not channel the air flow directly at people, especially at infants or the aged.
Take fresh air occasionally especially when gas appliance is running at the same time.
STRICT
CAUTION
STRICT
ENFORCEMENT
PROHIBITION
PROHIBITION
Do not use power supply cord
extended or connected in halfway
PROHIBITION
Do not insert objects into the air inlet or outlet.
PROHIBITION
Do not try to repair or reconstruct by yourself.
Do not operate the switch with wet hand.
PROHIBITION
Do not install the unit near a fireplace or other heating apparatus.
PROHIBITION
Do not place animals or plants in the direct path of the air flow
PROHIBITION
Check good condition of the installation stand
Do not place any objects on or climb on the unit.
ENFORCEMENT
PROHIBITION
PROHIBITION
4
STRICT
PROHIBITION
Do not pour water onto the unit for cleaning
PROHIBITION
Do not place flower vase or water containers on the top of the unit.
PROHIBITION
Parts and Functions
Indoor unit
Display panel
Inlet grille
Air Purifying Filter
(inside)
Vertical louver
(Use remote controller to adjust up and down air flow. Don't adjust it manually)
Horizontal louver
(adjust left and right air flow)
Outdoor unit
Outlet
Air filter(inside)
Anion generator (inside)
Power plug
HSU-09RC03/R2(DB) HSU-12RC03/R2(DB) HSU-18RC03/R2(DB)
1 2
4
HSU-22RC03/R2(DB)
OUTLET CONNECTING PIPING AND ELECTRICAL WIRING
3
DRAIN HOSEINLET
4
5
Parts and Functions
11. LOCK display
12. FAN SPEED display
?
31
1. HEALTH button Used to set healthy operation.
2. HOUR button Used to set clock and timer setting.
3. MODE button Used to select operation mode. AUTO, COOL,DRY, FAN,HEAT.
4. SLEEP button Used to select sleep mode.
5. CLOCK button Used to set correct time.
6. TIMER button Used to select TIMER ON, TIMER OFF, TIMER ON-OFF.
7. RESET When the remote controller appears abnormal, use a sharp pointed article to press this button to reset the remote controller normal.
8. HEALTH display
9. SLEEP display
10. SWING UP/DOWN display
LOW HI
13. TIMER ON display
14. TEMP button Used to select your desired temperature.
15. Operation mode display
Operation mode AUTO HEAT FANCOOL DRY
Remote controller
16. SINGAL SENDING display
17. POWER/SOFT display
18. Left/right air flow display
19. TEMP display Remote controller: to display the TEMP. setting.
20. TIMER OFF display
21. CLOCK display
22. FAN button Used to select fan speed: LOW,MED, HI, AUTO.
23. ON/OFF button Used for unit start and stop.
24. SWING UP/DOWN button Used to select up or down air sending direction.
25. SWING LEFT/RIGHT button Used to select left or right air flow.
26. HEALTH AIRFLOW button Used to set the health airflow mode.
27. SET button Used to confirm timer and clock settings.
28. POWER/SOFT button
29. LOCK Used to lock buttons and LCD display. If pressed, the other buttons will be disabled and the lock condition display appears. Press it once again, lock will be canceled and lock condition display disappears.
30. LIGHT button Colorful display bar of the controlling indoor machine is on and extinguished.
31. CODE Used to select CODE A or B with a press,A or B will be displayed on LCD. Please select A without special explanation.
MED AUTO
NOTE: (1)The following functions and related displays are not available: (2) Cooling only unit do not have functions and displays related with heating.
30631
Parts and Functions
Clock Set
When unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows:
1. Press CLOCK button,"AM" or "PM" flashes.
2. Press or to set correct time. Each press will increase or decrease 1 min. If the button is kept depressed, time will change quickly.
3. After time setting is confirmed, press SET, "AM" or "PM" stop flashing, while clock starts working.
Remote controller's operation
When in use, put the signal transmission head directly to the receiver hole on the indoor unit.
The distance between the signal transmission head and the receiver hole should be within 7 m without any obstacle as well.
Don't throw or knock the remoter controller.
When electronic-started type fluorescent lamp or change-over type fluorescent lamp or wireless telephone is installed in the room, the receiver is apt to be disturbed in receiving the signals, so the distance to the indoor unit should be shorter.
Loading of the battery
Load the batteries as illustrated right 2 R-03 (7#) batteries
Remove the battery cover:
Slightly press" "area and push down the cover as illustrated.
Load the battery:
Be sure that the loading is in line with the "+" / "- ". request as illustrated on the bottom of the case.
Put on the cover again.
Confirmation indicator:
After pressing power ON/OFF, if no display, reload the batteries.
Note:
Full display or unclear display during operation indicates the batteries have been used up. Please change batteries.
Used two new same-typed batteries when loading. If the remote controller can't run normally during operation, please remove the batteries and
reload several minutes later.
Hint:
Remove the batteries in case unit won't be in usage for a long period. If there are any display after taking-out, just need to press reset key.
7
Operation
Health Operation
Remote controller
Display panel
1. Unit start
Link with electronic power.
Press ON/OFF on the remote controller, unit starts.
The liquid crystal will display the working state of last time (Except Timer, Sleep, Power/Soft and Health airflow).
Then set up the comfortable working state.
2. Select operation mode
Press HEALTH button. For each press, is displayed. The pilot light of healthy process on the display board is on, hence healthy process begins.
When indoor fan motor is running, it has healthy process function. (It's available under any mode)
3. Unit stop
Press HEALTH button, the healthy function stops. The pilot light of healthy process on the display board is extinguished.
BRIEF INTRODUCTION TO HEALTH OPERATION
The anion generator in the air conditioner can generate a lot of anion to effectively balance the quantity of position and anion in the air and also to kill bacteria and speed up the dust sediment in the room and finally clean the air the room.
Note
When the fan in the indoor unit does not work, the health lamp lights up, but the anion generator does not release anion.
8
Loading...
+ 18 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use