Haier HSU-09LQA13-R2-DB-WT, AS12GB2LAA, HSU-18LEK03-R2-DB, HSU-10LQA13, AS12GS1ERA User Manual

SPLIT TYPE ROOM AIR CONDITIONER
OPERATION MANUAL

HSU-10LQA13
HSU-15LQA13
HSU-10LQAB13
HSU-15LQAB13

HSU-09LQA03/R2(DB)
HSU-12LQA03/R2(DB)
HSU-09LQA13/R2(DB)-WT
HSU-09LQA13/R2(DB)-BK
HSU-12LQA13/R2(DB)-WT
HSU-12LQA13/R2(DB)-BK

HSU-12LEK03/R2(DB)
HSU-18LEK03/R2(DB)
HSM24HEK03/R2(DB)

AS12GS1ERA
AS18GS1ERA

AS12GB2LAA

HSU-10VEK03
HSU-13VEK03
HSU-18VEK03
HSU-24VEK03
AS05GA1LAA
AS09GA1LAA
AS12GB1LAA
AS18GD1LAA

HSU-19CXAR3N
HSU-19CXBW3N

HSU-09CK3W3N HSU-09LEK03-Y3
HSU-09CK6G2N
HSU-09CK6B2N
HSU-12CK3W3N
HSU-12CKCS3N
HSU-12CK6G2N
HSU-12CK6B2N
HSU-12CKAG3N
HSU-12CKAB3N
HSU-18CK3W3N
HSU-18CK6B2N
HSU-18CK6G2N
HSU-18CKBS3N
HSU-15CKBS5N
HSU-18CKBS5N
HSU-18CKAB3N
HSU-18CKAG3N
HSU-15CKAG5N
HSU-18CKCS3N
HSU-24CK6B2N
HSU-13CXAS5N
HSU-13CXAS3N
HSU-13CXAR3N
HSU-13CXBW3N
HSU-19CXBW5N
HSU-24CXAS3N
HSU-19CXAS5N
HSU-19CXAS3N

HSU-12LEK03-Y3
HSU-18LEK03-Y3
HSU-24LEK03-Y2
HSU-09LEK03/R2(DB)
HSU-24LEK03/R2(DB)
HSU-10LIN13
HSU-09LTS14
HSU-12LTS14
HSU-18LTS14
HSU-24LTS14
HSU-07LEK03

Contents

PARTS AND FUNCTIONS

OPERATION
MAINTENANCE
CAUTIONS

TROUBLE SHOOTING

2
3
6

7
8

Please read this operation manual before using the air conditioner.
Keep this operation manual for future reference.

0010564364

Parts and Functions

Indoor Unit

Inlet

Inlet
grille

Nano-Aquo
Generator
（inside）

Outlet

Display board

Aureole

Display mode，the aureole display different
colour when setting different function
COOL: blue
AUTO: white DRY: cyan

Inlet

Inlet grille

Outlet

Horizontal flap

(adjust up and down air flow
Don't adjust it manually)

Display board

1

Signal receiver hole

2

ON/OFF display

3

Ambient temp.display

When receiving the remote
control signal, display the set
temperature and in the rest
time the room temperature is
displayed.

Inlet grille

2

2

Outlet

3

3

Anion generator

4

5

(inside)

7

Horizontal flap

(adjust up and down air flow
Don't adjust it manually)

9

Power indicator

10

Timer mode indicator

(Lights up whenTimer operation is selected.)

11

Operation mode indicator

(lights up when the compressor is on.)

12

Remote signal receiver

(A beeping sound is generated when a signal

from remote controller isreceived.)

Ambient temp display

13

When receiving the remote control signal, display the set
temperature and in the rest time the room temperature is
displayed and this room temperature is only for reference.

Actual inlet grille may vary from the one shown in the
manual according to the product purchased

2

Vertical blade

(adjust left and

right air fl

1

two sounds.

Inlet

1

1

Vertical blade

6

6

(adjust left and

ight air fl

r

(Lights up when unit starts.)

Horizontal flap

(adjust up and down air flow

Don't adjust it manually)

TEMP display

FAN: yellow

Nano-Aquo

Air Purifying Filter

ow)

Display board

2

3

TIMER ON\OFF display

4

TIMER ON-OFF display
SLEEP display

Note to the power failure resume:

press the sleep button ten times in five seconds
and enter function after hearing four sounds.And
press the sleep button ten times within five
seconds and leave this function after hearing

5

COOL\HEAT\Dry\AUTO display

Air Purifying Filter

5

4

12

ow)

Air Purifying

Anion

Filter

generator

(inside)

Vertical blade

(adjust left and

right air fl

: green

(inside)

Emergency

Switch

4

(inside)

8

Emergency

Switch

9
10
11

13

ow)

Remote controller

1

2

3

4

5
9

10

11

12

13

14

15

16

17

TURBO

SWING

HEALTH

TIME
ON

/QUIET

SLEEP

TIME
OFF

1. Mode display

Operation mode

Remote controller

AUTO

COOL DRY

FAN

2. Signal sending display

3. SWING display

5

4.FAN SPEED display

LO MED HI

Display
circulated

AUTO

5. LOCK display

Healthy function is not available for some units.

6. TIMER OFF display

6

TIMER ON display

7. TEMP display

7

Additional functions display

8

8.

Operation mode

Remote controller

QUIET

SLEEP

Supplemented
electrical
heating

HEALTH

TURBO

9. TURBO/QUIET button

18

19

20

21

FAN button

10.

11. COOL button

12.

SWING LEFT/RIGHT button
FAN SPEED button

13.

14. HEALTH display

15. SLEEP display

16.

22

23

24

25

LOCK

17. LIGHT button
Control the lightening and extinguishing

of the indoor LED display board.

18. POWER/SOFT display

19. DRY button

button

20. TEMP display

21.

SWING UP/DOWN

22.

TIMER OFF/ON

23.HEALTH AIR FLOW

button

displa

button

24.CANCEL/CONFIRM button
Function: Setting and cancel to the

timer and other additional functions.

25. RESET button
When the remote controller appears
abnormal, use a sharp pointed
article to press this button to reset
the remote.

Outdoor Unit

OUTLET

INLET

CONNECTING PIPING

4

AND ELECTRICAL WIRING

DRAIN HOSE

4

Loading of the battery

Remove the battery cover;

1

Load the batteries as illustrated.

2

2 R-03 batteries, resetting key

(cylinder);

Be sure that the loading

3

is in line with th

Load the battery,then put on the cover again.

4

Note:

The distance between the signal transmission head and the rece­iver hole should be within 7m without any obstacle as well.

When electronic-started type fluorescent lamp or change- over

type fluorescent lamp or
room, the recei

ver is apt to be disturbed in receiving

so the distance to the indoor unit should be shorter.

Full display or unclear display during operation indicates the

ries have been used up.

batte

If the remote controller can't run normally during operation, please

remove the batteries and

wireless telephone is installed in the

Please change batteries.

reload several minutes later.

e" + "/"-";

the signals,

Operation

Base Operation

TURBO

Remote controller

1. Unit start

Press ON/OFF on the remote controller, unit starts.

2. Select operation mode

COOL button:Cooling mode
FAN button: Faning mode
DRY button: Dehumidify mode

3.Select temp.setting

Press

/

Every time the button is pressed, temp.setting
increase 1
rapidly

Every time the button is pressed, temp.setting
decrease 1
decrease rapidly

Select a desired temperature.

button

o

C,if kept depressed, it will increase

o

C,if kept depressed, it will

4.Fan speed selection

Press FAN button. For each press, fan speed

changes as

Remote controller:

Air conditioner is running under displayed fan speed.
When FAN is set to AUTO, the air conditioner
automatically adjusts the fan speed according to room
temperature.

Operation

Mode

AUTO

COOL

DRY

FAN

follows:

LOW

Remote

Controller

MED HI

Under the mode of auto operation, air conditioner will
automatically select Cool or Heat operation according to

room temperature. When FAN is set to AUTO the air
conditioner automatically adjusts the fan speed according
to room temperature.

according to room

In DRY mode , when room temperature becomes lower

than temp.setting+2

speed regardless of FAN setting.

In FAN operation mode , the unit will not operate in COOL or

HEAT mode but only in

FAN mode. And temp. setting is disabled. In FAN mode,
sleep operation is not available.

/QUIET

2

SWING

HEALTH

TIME
ON

1

1

3

4

2

3

SLEEP

TIME
OFF

Display

circulated

AUTO

Note

temperature.

o

C, unit will run intermittently at LOW

FAN mode, AUTO is not available in

Emergency operation and test operation

Emergency Operation:

Use this operation only when the remote controller is defective
or lost, and with function of emergency running, air conditoner
can run automatically for a while.
When the emergency operation switch is pressed, the " Pi "
sound is heard once, which means the start of this operation.
When power switch is turning on for the first time and
emergency operation starts, the unit will run automatically in
the following modes:

Room
temperature

Above 23oC 26oC AUTO COOL

Designated
temperature

Timer
mode

No

Fan

speed

Operation

mode

Pi

It is impossible to change the settings of temp. and fan speed,It
is also not possible to operate in timer or dry mode.

Test operation:

Test ope ration switch is the same as emergency switch.

Use this switch in the test operation when the room

temperature is below 16
normal operation.

Continue to press the test operation

switch for more than 5 seconds . After

you hear the "Pi" sound twice,
your finger from the switch: the cooling
operation starts with the air flow speed "Hi".

Under this operation mode,the fan motor of indoor

unit will run in high speed.

o

C, do not use it in the

release

Pi Pi

Air Flow Direction Adjustment

1.Status display of air flow

Vertical flap

Pos.1

Initial state

Pos.2 No initial state disaplayed on remote controller, the

vertical flap will be fixed on the current position

2.Left and right air flow adjustment

For each press of button, remote controller
displays as follows :

remote controller:

Pos.1

Pos.5

Pos.2

Pos.6

Pos.3

Pos.4

Cautions:

When adjusting the flap by hand,turn off the unit.

When humidity is high,condensate water might occur
adjusted to left or at air outlet if all vertical louvers are right.
It is advisable not to keep horizontal flap at downward
position for a long time in COOLor DRY

otherwise, condensate water might occur.

Note:
When restart after remote turning off, the remote controller

controller will automatically memorize the previous set swing position.

swing)

(Auto

mode ,

3

Operation

Sleep Operation

Before going to bed,you can simply press the SLEEP
button and unit will operate in SLEEP mode and bring
you a sound sleep.

Operation Mode

1. In COOL,DRY mode

1 hours after SLEEP mode starts,temp.will become

higher than temp.setting.After another 1 hours,temp.rises

O

C

by 1 futher.The unit will run for further

T

emp. is higher than temp.setting so that room temperature

6 hours then stops

won’t be too low for your sleep.

O

C

1

Note

When TIMER function is set, the sleeping function can’t be

if user resets

p

set up .After the sleeping function is set u
TIMER function, the sleeping function will be cancelled; the

machine will be in the state of

timing-on.

,

TURBO/QUIET Operation

TURBO

/QUIET

TURBO

/QUIET

When you need fast cool or fast dehumidification,you can

choose the Turob function; when you sleep, read, you can

choose Quiet function

Press the

TURBO

bu on, you can switch the “Turbo” and “Quiet”

/QUIET

SLEEP operation starts SLEEP operation stops

Approx.6hrs

O

C

Rises 1

Rises 1

O

C

Unit stop

1 hr

1 hr

Temp.setting

In COOL, DRY mode

In AUTO mode

2.

The unit operaters in corresponding sleep mode
adapted to the automatically selected operation

3. In FAN mode

It has no SLEEP function.

mode.

will swith as below

（TURBO）

（QUIET）

cancel

When running in Turbo，the fan speed is the highest,

when running in Quiet, the fan speed is super slow

HEALTH Operation

Nano-Aqua generator adopt two high voltage
pole to ionize the water molecule into
nanometer water ion,and release these ions
to the air to kill the bacterium and refresh
the air. as well as the nanometer water inon
can be easily absorbed by skin,keeping moisture

4.Set the wind speed change when sleeping
If the wind speed is high or middle before setting for the

sleep, set for lowing the wind speed after sleeping.
If it is low wind, no change.

4

anytime.

Operation

Timer On/Off On-Off Operation

1.After unit starts, select your desired operation mode.

2.Press TIMER button to change TIMER mode. Every

time the button is pressed, display changes as follows:

Remote controller:

0.5h

TIMER ON TIMER OFF TIMER ON-OFF

0.5h 0.5h

0.5h

TIMER OFF-ON

Then select your desired TIMER mode (TIMER ON or

TIMER OFF or TIMER ON-OFF). " "or " "will flash.

3.Press / button to set time.

Press the button for each time, setting time in the first
12 hours increased by 0.5 hour every time, after 12
hours,increased by 1 hour every time.

BLANK

Health airflow Operation

1.Press to starting

Setting the comfort work conditions.

2.The setting of healthy airflow function

Press button to select “ Healthy airflow”, the remote

controller will switch as below

Healthy
airflow
upwarder

Notice: Do not direct the flap by hand. Otherwise, the

grille will run incorrectly. If the grille is not run correctly,

stop for a minute and then start, adjusting by remote

controller.

Note:

Healthy
airflow
downwarder

fixed

location

Press the button for each time, settiing time in the first
12 hours decreased by 0.5 hour every time, after 12
hours,decreased by 1 hour every time.

It can be adjusted within 24 hours.

4.Confirm timer setting

After adjust the time,press button and confirm the

time ON or OFF button will not flash any more.

5.Cancel timer setting
Press the timer button by times until the time display

eliminated.

Hints:
After replacing batteries or a power failure happens, time
setting should be reset.

According to the Time setting sequence of TIMER ON or

1.After setting the healthy airflow function, the position

grill is fixed.

2.In cooling, it is better to select the

mode.

3.In cooling and dry, using the air conditioner for a long
time under the high air humidity, condensate water may

occur at the grille .

TIMER OFF, either Start-Stop or Stop-Start can be
achieved.

5

Maintenance

6

For Smart Use of The Air Conditioner

Setting of proper room
temperature

Proper

temperature

Close doors and windows
during operation

During cooling operation
prevent the penetration
of

direct sunlight with

curtain or blind

If the unit is not to be used
for a long time, turn off the
power supply main switch.

OFF

Do not block the air inlet
or outlet

Use the timer effectively

Use the louvers effectively

Remote Controller Indoor Body

wipe the air conditioner by using a
soft and dry cloth.For serious stains,

Do not usewater,wipe the controller
with a dry cloth.Do not use glass

cleaner or chemical cloth.

use a neutral detergent diluted with
water.Wring the water out of the
cloth before wiping,then wipe off the
detergent completely.

Do not use the following for cleaning

Gasoline,benzine, thinner or cleanser

damage the coating of the unit.

ay

m

Hot water over 40
cause

discoloring or deformation.

Air Filter cleaning

Open the inlet grille by pulling it upward.

Remove the filter.

Push up the filter's center tab slightly until it is

released

Clean the filter.

Use a vacuum cleaner to remove dust, or wash the filter with
water.After washing, dry the filter completely in the shade.

Attach the filter.

Attach the filter correctly so that the "FRONT" indication

is

completely
and left filters are not

may cause defects.

Close the inlet grille.

from the stopper, and remove the filter do

facing to the front.Make sure that the filter is

fixed behind the stopper.If the right

attached correctly, that

O

C(104OF) may

wnw

ard.

Once every
two weeks

Replacement of Air Purifying Filter

1.Open the lnlet Grille

Prop up the inlet grille by using a

small device named grille-support

which located in the right side of
the indoor unit.

2.Detach the standard air filter

Slide the knob slightly up
release the filter, then withdraw it.

3.Attach Air Purifying Filter

Put air purifying filter appliances into the

right and left filter frames.

ward to

Detach old Air Purifying Filter

4.Attach the standard air filter

(Necessar

y installation)

ATTENTION:

The white side of the photocatalyst air purifying filter
face outside,and the black side face the unit The green

side of the bacteria-killing medium air purifying filter face
outside,and the white side face the unit.

5.Close the Inlet Grille

Close the Grille surely

NOTE:

The photocatalyst air purifying filter will be solarized in fixed
time. In normal family,

The bacteria-killing medium air purifying filter will be used
for a long time,no need for replacement. But in the period
of using them ,you should remove the dust frequently by

using vacuum cleaner or flaping them lightly,otherwise ,

its performance will be affected.

Please keep the bacteria-killing medium air purifying filter in
the cool and dry conditions
when you stop using it,or its ability of sterilization will

reduced.

it will be solarized every 6 months.

avoid long time directly sunshine

be

Cautions

WARNING

Please call Sales/Service Shop for the Installation.

Do not attempt to install the air conditioner by yourself because improper works
may cause electric shock, fire, water leakage.

WARNING

When abnormality such as burnt-small found,
immediately stop the operation button and
contact sales shop.

Use an exclusive
power source
with a circuit
breaker

Check proper
installation of the
drainage securely

OFF

Connect power supply cord
to the outlet completely

STRICT

ENFORCEMENT

Do not use power supply
cord in a bundle.

ENFORCEMENT

Use the proper voltage

Take care not to damage

the power supply cord.

PROHIBITION

Do not start or stop the
operation by disconnecting
the power supply cord
and so on.

PROHIBITION

Do not use for the purpose of storage of
food, art work, precise equipment,
breeding, or cultivation.

Do not channel the air flow directly
at people, especially at infants or
the aged.

STRICT

STRICT

ENFORCEMENT

PROHIBITION

PROHIBITION

CAUTION

Take fresh air occasionally especially
when gas appliance is running at the
same time.

STRICT
ENFORCEMENT

1.Do not use power supply cord extended
or connected in halfway

2.

Do not install in the place where there is any

possibility of inflammable gas leakage around the unit.

3.Do not get the unit exposed

to vapor or oil steam.

PROHIBITION

Do not insert objects into the air
inlet or outlet.

PROHIBITION

Do not try to repair or
reconstruct by yourself.

Do not operate the switch with
wet hand.

Connect the earth
cable.

earthing

PROHIBITION

Do not install the unit near a fireplace
or other heating apparatus.

PROHIBITION

Do not place animals or plants in
the direct path of the air flow

PROHIBITION

STRICT

ENFORCEMENT

Check good condition of the
installation stand

PROHIBITION

Do not place any objects on or
climb on the unit.

PROHIBITION

PROHIBITION

Do not pour water onto the unit
for cleaning

PROHIBITION

Do not place flower vase or water
containers on the top of the unit.

PROHIBITION

7

Trouble shooting

Cautions

Before asking for service, check the following
first.

Cause or check points

When unit is stopped, it won't restart
immediately until 3 minutes have
elapsed to protect the system.

When the electric plug is pulled out
and reinserted, the protection circuit

will work for 3 minutes to protect the

air conditioner.

During unit operation or at stop,
a swishing or gurgling noise may
be heard.At first 2-3 minutes after

unit start, this noise is more noticeable.
(This noise is generated by
refrigerant flowing in the system.)

During unit operation, a cracking

noise may be heard.This noise is
generated by the casing expanding

or shrinking because of
temperature changes.
Should there be a big noise from

air flow in unit operation, air

filter may be too dirty.

This is because the system
circulates smells from the interior
air such as the smell of furniture,
paint, cigarettes.

During COOL or DRY operation,
indoor unit may blow out mist.

This is due to the sudden cooling
of indoor air.

In DRY mode, when room temperature

becomes lower than temp.

setting+2

intermittently at LOW speed

regardless of FAN setting.

Is power plug inserted?

Is there a power failure?

Is fuse blownout?

Is the air filter dirty?

Normally it should be cleaned

every 15 days.
Are there any obstacles before
inlet and outlet?
Is temperature set correctly?
Are there some doors or

windows left open?
Is there any direct sunlight
through the window during the

cooling operation?(Use curtain)

Are there too much heat sources
or too many people in the room
during cooling operation?

o

C,unit will run

Normal
Performance
inspection

Multiple

check

Phenomenon

The system
does not restart
immediately.

Noise is heard

Smells are
generated.

Mist or steam are
blown out.

In dry mode,
speed can’t be
changed.

Poor cooling

fan

Do not obstruct or cover the ventilation

conditoner.Do not put fingers

inlet/outlet and

Do not allow children to play with the air

case should children be

swing louver.

or any other things into the

allowed to sit on the outdoor unit.

grille of the air

conditioner

Specifications

The refrigerating circuit is leak-proo f.

The machine is adaptive in following

1.Applicable ambient temperature range:

Indoor

Cooling

2. If the power supply cord is damaged, it
manufacturer

3. If the fuse of indoor unit on PC board is

it with the type of

broken,change it with the type of

4. The wiring method should be in line with

5. After installation, the power plug should

6. The waste battery should be disposed

7. The appliance is not intended for use

persons

8.Young children should be supervised

the appliance.

with

9. Please employ the proper power plug,
cord.

The power plug and connecting cable

10.
attestation.

11.In order to protect the units,please turn

30 seconds

Outdoor

or its service agent or a similar

without supervision.

later, cutting off the power.

Maximum:D.B/W.B
Minimum:D.B/W.B

Maximum:D.B/W.B
Minimum:

T. 3.15A/ 250V

D.B

must be replaced

broken,please

. If the fuse of

T.25A/250V

the local wiring

be easily reached.

properly.

by young children or

to ensure that th

which fit into the

must have

off the A/C first,

situation

32oC/23oC

o

21

C/15oC

o

46

C/26oC

o

18

C

qualified

outdoor

acquired the local

.In no

person.

change

unit is

standard.

ey

do not play

p

ower supply

and at least

by the

infirm

Haier

Address:No.1 Haier Road,Hi-tech Zone,Qingdao 266101 P.R.China
Contacts: TEL [phone];FAX [phone]

Website: www.haier.com

8