Haier HSU-09LF03, HSU-12LF03 User Manual

Installation Manual of Room Air Conditioner
Read this manual before installation Explain sufficiently the operating means to the user according to this manual.
Necessary Tools for Installation
1.Driver cksaw
2.Ha
3.Hole core d
rill
Accessory parts
No. Accessory parts
1
2
3
4
5
6
Remote controller
R-03 d
Mounting plate
Drain hose
Steel nail, cement
4X25
Screw
Plastic cap
ry battery
4X50
Number of articles
1
2
1
1
6
4
5.
Torque wrench(17mm,22mm,26mm)
6.Pipe cutter ring tool
7.Fla fe
8.Kni
9.Nipper 12.Reamer
10.Gas leakage detector or soap-and-
water solution
11.Measuring tape
Drawing for the installation of indoor and outdoor units
mc5 na
h
t er
om
Optional parts for piping
Mark
A
B
C
D
E
F
G
Parts name
Non-adhesi
Adhesive tape
Saddle(L.S) with scr
Connecting elect for indoor and outdoor
Drain hose
Heating insulating material
Piping hole c
ve tape
ews
ric cable
over
m
o
r
e
t
h
a
n
1
0
c
m
Attention must be paid to the rising up of drain hose
m
o
r
e
t
h
a
n
1
c0
m
A
1
1
4
1
1
10
11
7
8
9
Drain-elbow
Cover
Cushion
Pipe supporting plate
Connecting cable
Note:Cooling only units don't have Drain-elbow
No.0010518285
Arrangement of piping directions
Rear left
Below
Rear right
Right
Left
m
c
0
1
n
a
h
t
e
r
o
m
m
o
r
e
t
h
a
n
1
0
c
m
m
c
0
6
n
a
h
t
e
r
o
m
A
The marks from to in the figure are the parts numbers.
G
The distance between the indoor unit and the floor should be more than 2m.
C
D
m
o
r
e
t
h
a
n
1
5
c
m
140 140415
Floor fixing dimensions of the outdoor unit (Unit:mm)
HSU-09LF03 HSU-12LF03
082
Fixing of outdoor unit
Fix the unit to concrete or block with bolts( 10mm) and nuts firmly and horizontally.
When fitting the unit to wall surface, roof or rooftop, fix a supporter surely with nails or wires in consideration of earthquake and strong wind.
If vibration may a
Indoor Unit
Place, robust not causing vibration, where the body can be supported
fficiently.
su Place, not a inlet and outlet of the unit are not disturbed. Place, possible to drain easi outdoor unit. Place, where cold air can be spread in a room entire Place, nearby a power receptacle, with enough space around. (Refer to drawings). Place where the distance of more than lm from televisions, radios, wireless apparatuses and fluorescent lamps can be left. In the case of fixing the remote controller on a wall, place where the indoor unit can receive signals when the fluorescent lamps in the room are lightened.
ffected by heat or steam generated in the vicinity, where
Selection of Installation Place
ly, where piping can be connected with the
ly.
ffect the house, fix the unit by attaching a vibration-proof mat.
Outdoor Unit
Place, which is less affected by rain or direct sunlight and is
fficiently ventilated.
su Place, possible to bear the unit, where vibration and noise are not increased. Place, where discharged wind and noise do not cause a nuisance to the neighbors. Place, where a distance marked is available as illustrate in the above figure.
Power Source
Before inserting power plug into receptacle, check the voltage without fail
Install an exclusive branch circuit of the pow
A receptacle shall be set up in a distance where the power cable can be reached. Do not extend the cable by cutting it.
er.
. The power source is the same as the corresponding name plate.
d
Selection of pipe
To this unit, both liquid and gas pipes shall be insulated
as they become Iow temperature in operation.
Use optional parts for piping set or pipes covered with
equivalent insulation material.
For 09
Liquid pipe ( )
Gas pipe ( ) 9.52mm(3/8")
6.35mm(1/4")
2
For 12
6.35mm(1/4")
12.7mm(1/2")
Indoor unit
Indoor unit
1.Fitting of the Mounting Plate and Positioning of the wall Hole
When the mounting plate is first fixed
1.Carry out, based on the neighboring pillars or lintels, a proper leveling for the plate to be fixed against the wall, then temporarily fasten the plate with one steel nail.
2. Make sure once more the proper level of the plate, by hanging a thread with a weight from the central top of the plate, then fasten securely the plate with the attachment steel nail.
3. Find the wall hole location A using a measuring tape
B= 60mm
A=145mm
30mm
When the mounting plate is fixed side bar and lintel
Fix to side bar and lintel a mounting bar, Which is separately sold, and then fasten
the plate to the fixed mounting bar.
Refer to the previous article, " When the mounting plate is first fixed ", for the position of wall hole.
2.Making a Hole on the Wall and Fitting the Piping Hole Cover
Make a hole of 60 mm in diameter, slightly descending to outside the wall. Install piping hole cover and seal it off with putty after installation
Indoor side
Wall hole
60mm
(Section of wall hole)
G
Piping hole pipe
Outdoor side
Thickness of wall
3.Installation of the Indoor Unit
Drawing of pipe
[ Rear piping ]
Draw pipes and the drain hose, then fasten them with the adhesive tape
[ Left Left-rear piping ]
In case of left side piping, cut away, with a nipper, the lid for left piping. In case of left-rear piping, bend the pipes according to the piping direction to the mark of hole for left-rear piping which is marked on heat insulation materials.
3
Indoor unit
1. Insert the drain hose into the dent of heat insulation materials of indoor unit.
2. Insert the indoor/outdoor electric cable from backside of indoor unit, and pull it out on the front side, then connect them.
3. Coat the flaring seal face with refrigerant oil and connect pipes. Cover the connection part with heat insulation materials closel
y, and make sure fixing with adhesive tape
Lid for right piping
Lid for under piping
Fix with adhesive tape
Lid for left piping
Heat insulation material
Drain hose
Piping
Indoor/outdoor electric cable
Indoor/outdoor electric cable and drain hose must be bound with refrigerant piping by protecting tape.
[Other direction piping]
Cut awa to the position of wall hole. When bending, be careful not to crash pipes.
Connect beforehand the indoor/outdoor electric cable, and then pull out the connected to the heat insulation of connecting part speciall
y, with a nipper, the lid for piping according to the piping direction and then bend the pipe according
y.
Fixing the indoor unit body
Hang surely the unit body onto the upper notches of the mounting plate. Move the body from side to side to verify its secure fixing. In order to fix the body onto the mounting plate,hold up the body aslant from the underside and then put it down perpendicularl
y.
mounting plate
Unloading of indoor unit body
When you unload the indoor unit,please use your hand to arise
the body to leave agraffe,then lift the bottom of the body outward
slightly and lift the unit aslant until it leaves the mounting plate.
4
mounting plate
agraffe
Indoor unit
Connecting the indoor/outdoor Electric Cable
Removing the wiring cover
Remove terminal cover at right bottom corner of indoor unit, then take o
ff wiring cover by removing its screws.
When connecting the cable after installing the indoor unit
1. Insert from outside the room cable into left side of the wall hole, in which the pipe has already
2. Pull out the cable on the front side, and connect the cable making a loop.
When connecting the cable before installing the indoor unit
Insert the cable from the back side of the unit, then pull it out on the front side. Loosen the scr Pull the ca After the ca Note is not correct, proper ope
1. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person. The type of connecting wire is H05/07RN-F or 245IEC57(YZW).
2. If the fuse on PC board is broken please change it with the type of T. 3.15A/250V.
3. The wiring method should be in line with the local wiring standard.
4. After installation, the power plug should be easily reached. A breaker should be incorporated into fixed wiring. The breaker should be all-pole switch and the
5.
distance between its two contacts should be not less than 3mm.
ble slightly to make sure the cables have been properly inserted and tightened.
ble connection, never fail to fasten the connected cable with the wiring cover.
: When connecting the cable, confirm the terminal number of indoor and outdoor units carefully. If wiring
existed.
ews and insert the cable ends fully into terminal block, then tighten the screws.
ration can not be carried out and will cause defect.
3 4
) N
( 2
L) 1(
Indoor unit
connecting wiring:
-mod 09-12:
34:
HSU-09LF03
HSU-12LF03
3G1.0mm 2G1.0mm
5
1( L)
2( N)
Outdoor unit
Power cable:
-mod 09-12:
3G1.0mm
Outdoor unit
Outdoor unit
1.Installation of Outdoor Unit
Dr
Install according to
2.Connection of pipes
To bend a pipe, give the roundness as large as possible not to crush the pipe Connecting the pipe of gas side first ma The max
vertical distance between the indoor unit and the outdoor unit is 5 m.
awing for the installation of indoor and outdoor units
kes working easier.
Flare
Half union
Spanner
Torque wrench
Be careful that matters, such as wastes of sands, etc. shall not enter the pipe.
nut
Forced fastening without careful centering may damage the threads and cause a leakage of ga
Pipe Diameter ( )
Liquid side 6.35mm(1/4")
Liquid side 9.52mm(3/8")
Gas side 9.52mm(3/8")
Gas side 12.7mm(1/2")
s.
Fastening torque
18N.m
40N.m
42N.m
50N.m
3.Connection
Use the same method on indoor unit
rminal block, then tighten the screws.
te
rt the cable according to terminal number in the same manner as the indoor unit.
Inse If wi
ring is not correct, proper operation can not be carried out and controller may be damaged.
Fix the ca
4.Atta
ble with a clamp.
ching Drain-Elbow
. Loosen the screws on terminal block and insert the plugs fully into
If the drain-elbow is used, please attach it as figure. (Note: Only for heat pump unit.)
6
Outdoor unit
5.Purging Method:
Push the air out of the indoor unit and piping as followes:
(1) Remove the valve cap on 2-way valve in outdoor unit.
(2) Loosen by 1/2 turn the flare nut of gas pipe, which is conneted to 3-way valve.
(3) Loosen 2-way valve by 90 hexagon wrench, and after approx. 10 sec tighten it up. Gas comes out through flare nut on wide pipe. If no gas is discharged, tighten flare nut with specified torque.
o
using
way valve
2-
6.35mm(1/4")
3-way valve
9.52mm(3/8")
(4) Open 2-way and 3-way valves using specified torque.
(5)
Tighten the caps on the valves
with specified torque.
Tighten torque N.m
Valve rod
Valve cap
When connecting pipe exceeds 5 meters, 20g or 60g(only for 24k) refrigerant shall be added per exceeding meter . Charge according to the following list.
7-9
20-25
for 9k 12k
Piping length
Additional amount
5m 7m
No need
40g
10m
100g
HSU-09LF03 HSU-12LF03
Note: When extending piping, air inside piping shall be removed by using external refrigerant gas, charge according to the following list.
1.Power Source Installation
The power source must be exclusively used for air conditioner. (Over I0A) In the case of installing an air conditioner in a moist plac
rth leakage breaker.
ea For installation in other places, use a circuit breaker as far as possible.
e, please install an
2.Cutting and Flaring
Pipe cutting is car After inse
rting the flare nut, flaring work is carried out.
A
ried out with a pipe cutter and burs must be removed.
Flare tooling die
Correct
Lean Damage of flare Crack Partial Too outside
3.On Drain
Please install the d Please don't do the d
age
rain hose so as to be downward slope without fail.
rainage as shown below.
Work of Piping
Liquid side
Liquid side
Gas side
Gas side 12.7mm(1/2")
Incorrect
Pipe diameter( )
6.35mm(1/4")
9.52mm(3/8")
9.52mm(3/8")
Size A(mm)
0.8~1.5
1.0~1.8
1.0~1.8
1.2~2.0
It becomes high midway.
Please pour
ried out surely to outdoor.
car
The end is immersed
water.
in
water in the drain pan of the indoor unit, and confirm that drainage is
In case that the attached d to it without
Please kindly
fail.
ck for Installation and Test Run
Che
explain to our customers how to operate through the instruction manual.
Check Items for Test Run
Gas leak from pipe connecting? Heat insulation of pipe connecting? Are the connecting wi indoor and outdoor fi to the te
rminal block? Is the connecting wi and outdoor fi
rings of
rmly inserted
ring of indoor
rmly fixed?
Less than 5cm
It
waves. The gap with the ground
is too small
There is the bad smell from a ditch
rain hose is in a room, please apply heat insulation
Put che
ck mark in boxes
Is d
rainage securely carried out?
Is the ea
rth line securely connected? Is the indoor unit securely fi Is p
ower source voltage abided by the code? Is there a
ny noise?
xed?
Is the lamp no Are cooling and heating (when in heat pump) per Is the ope regulator no
rmally lighting?
formed normally?
ration of room temperature
rmal?
8
Loading...