Haier HSU-09H03-K, HSU-12H03/K User Manual

SPLIT TYPE ROOM AIR CONDITIONER

OPERATION MANUAL

HSU-09H03/K(F) HSU-12H03/K(F)

Contents

PARTS AND FUNCTIONS

OPERATION

CAUTIONS

TROUBLE SHOOTING

1 2-5

6.7 7

Please read this operation manual before using the air conditioner.

Keep this operation manual for future reference.

0010531056

Parts and Functions

Indoor Unit

Inlet

Inlet grille

Air Purifying Filter (inside)

Outlet

Horizontal flap

(adjust up and down air flow Don't adjust it manually)

Vertical blade

(adjust left and right air flow)

Anion generator

Actual inlet grille may vary from the one shown in the manual according to the product purchased

Display board

Signal receiver hole

iFP display

HEALTH display

(If the unit which you purchased

has healthy function,follow it. If not,please ignore.)

TIMER OFF display

TIMER ON display SLEEP display

Ambient temp.display

When receiving the remote control signal, display the set temperature and in the rest time the room temperature is displayed and this room temperature is only for reference.

SMART display

COOL display

Dry display

HEAT display

Air Filter cleaning

Open the inlet grille by pulling it upward.

Remove the filter.

Push up the filter's center tab slightly until it is released from the stopper, and remove the filter downward.

Clean the filter.

Use a vacuum cleaner to remove dust, or wash the filter with water.After washing, dry the filter completely in the shade.

Attach the filter.

Attach the filter correctly so that the "FRONT" indication is facing to the front.Make sure that the filter is completely fixed behind the stopper.If the right and left filters are not attached correctly, that may cause defects.

Close the inlet grille.

Outdoor Unit

OUTLET

INLET

CONNECTING PIPING AND ELECTRICAL WIRING

DRAIN HOSE

(inside)

Once every two weeks

Remote controller

Outer side of the controller

Operation mode display

Display of each function status

SMART button

Used to set SMART operation.

COOL button

Used to set COOL operation.

HEAT button

Used to set HEAT operation.

DRY button

Used to set DRY operation.

ECONOMY button

Used to set ECONOMY operation.

iFP button

Induce the movement of the human body, so as to control the airflow/energy saving functioning.

Inner side of the controller

SWING button

Used to select up or down air sending direction.

HEALTH button

Used to set healthy operation.

HEALTH AIRFLOW button

Used to set the health airflow mode.

POWER / SOFT button

Use to set power/soft function.

LIGHT

button

Control the lightening and extinguishing of the indoor LED display board.

INQUIRE

button

Inquire the external environmental temperature and the operating power of the machine. (e.g. when the panel display “01”, the operating power is 100W; when the panel display “02”, the operating power is 200W, and so forth).

RESET button

When the remote controller appears abnormal,use a sharp pointed article to press this button to reset the remote controller normal.

Signal sending end

SMART

SET TEMP.

COOL

ROOM TEMP.

HEAT

FAN

DRY

AUTO AUTO

CTD

FAN SPEED

POWER

SOFT

ECO

iFP

AM PM

SMART ON/OFF

COOL

HEAT

DRY

ECONOMY FAN SPEED

iFP

SMART

SET TEMP.

COOL

AUTO

TIMER ON OFF

EVADE

ROOM TEMP.

HEAT

FAN DRY

AUTO AUTO

CTD

FAN SPEED

POWER

SOFT

ECO

iFP

AM PM

SMART

CODE button

Used to select CODE A or B with a press, A or B will be displayed on LCD. Please select A without special explanation.

AUTO

TIMER ON OFF

Signal sending display

TEMP display

Remote controller: to display the TEMP. setting.

FAN SPEED display SWING UP/DOWN display Left/right air flow display

TIMER ON display TIMER OFF display CLOCK display

ON/OFF button

Used for unit start and stop.

TEMP. button

Used to select your desired temperature.

FAN SPEED button

Used to select fan speed: LOW,MED, HI, AUTO.

FOOLLOW / EVADE button

Detect the location where the human body is, adjust the air deflector to blow/avoid the body.

NOTE:

This function unavailable on this models

SWING button

Used to select left or right air sending direction.

FRESH button

Used to set fresh operation.

SLEEP button

Used to select sleep mode.

CLOCK button

Used to set correct time.

TIMER ON / OFF button

Used to select TIMER ON, TIMER OFF,TIMER ON-OFF.

HOUR button

Used to set clock and timer setting.

CANCEL/CONFIRM button

Used to confirm timer and clock settings.

LOCK button

Used to lock buttons and LCD display. If pressed, the other buttons will be disabled and the lock condition

Press it once again, lock will be cancelled and lock condition display disappears.

display appears.

Operation

Loading of the battery

Remove the battery cover;

Clock set

SMART

Load the batteries as illustrated. 2 R-03 batteries,resetting key(cylinder); Be sure that the loading is in line with the" + "/"-";

Load the battery,then put on the cover again.

AM PM

Press CLOCK button,

"AM" or "PM" flashes.

Press “+” or “-” to set correct time.

Each press will increase or decrease 1min. If the

button

is kept pressed,time will change quickly.

SMATR Operation

One key can give you a comfortable room!

SMART

The air conditioning unit can judge the indoor temperature and humidity, and make the adjustment accordingly.

SMART

Press ON/OFF button, unit starts.

Press SMART button“ ” is displayed on the remote controller and “ ” is displayed on

the display board,

●

SMART FRESH

●

SMART Defrost SMART FAN SPEED

●

SMART FAN HEALTH

●

SMART DRY

●

SMART SOFT

●

SMART

Under the cooling, heating and dehumidifying mode, press the smart key to enter the smart function. Under the smart running mode, when the air conditioning is running, it will automatically select cooling, heating, dehumidifying or blowing mode as per the setting temperature. When the smart function is running, press the “cooling” “heating” or “dehumidifying” key to switch to the other mode, you will exit from the smart function.

SMART start

SMART

unit will run in SMART mode.

Control temperature

SMART stops

COOL,HEAT and DRY Operation

Select operation mode.

Unit start.

Confirm

time.

After time setting is confirmed, press CONFIRM,"AM "and "PM" stop flashing,while clock starts working.

Note:

The distance between the signal transmission head and the receiver hole should be within 7m without any obstacle as well.

When electronic-started type fluorescent lamp or change-over wireless telephone is installed in the type fluorescent lamp or room, the receiver is apt to be disturbed in receivingthe signals,

so the distance to the indoor unit should be shorter.

Full display or unclear display during operation indicates the

ries have been used up.

batte

If the remote controller can't run normally during operation,

please

If there are any display

remove the batteries and

Hint:

Remove the batteries in case unit won't be in usage for a long period.

after taking-out, just need to press reset key

Please change batteries.

reload several minutes later.

Press COOL button“ ” is displayed on the remote controller and “ ” is displayed on

SMART

1.In DR

Y mode, when room temperature becomes lower than temp.setting+2

unit will run intermittently at LOW speed regardless of FAN setting.

Remote controller can memorize each operation status. When starting it next time,

2. just press ON/OFF button and unit will run in previous status.

Cooling only unit do not have displays and functions related with heating.

the display board,

Press HEAT button“ ” is displayed on the remote controller and “ ” is displayed on the display board,

Press DRY button“ ” is displayed on the remote controller and “ ” is displayed on the display board,

unit will run in COOL mode.

unit will run in HEAT mode.

unit will run in DRY mode.

+ 5 hidden pages

Haier HSU-09H03-K, HSU-12H03/K User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual