Haier HSU-07HC03-R2, HSU-09HE03-R2, HSU-12HC03-R2, HSU-07HE03-R2, HSU-09HC03-R2 User Manual

Air Conditioner

       

Edition:2005/11/18

OPERRATION

SPLIT TYPE ROOM AIR CONDITIONER

OPERATION MANUAL

HSU-07HC03/R2 HSU-09HC03/R2 HSU-12HC03/R2 HSU-07HE03/R2 HSU-09HE03/R2 HSU-12HE03/R2

HSU-09HD03/R2 HSU-12HD03/R2 HSU-14HB03/R2 HSU-18HB03/R2 HSU-22HC03/R2 HSU-22HD03/R2 HSU-22HB03/R2HSU-07HD03/R2

Please read this operation manual before using the air conditioner.

No.0010557173

Contents

Cautions Parts and functions Operation

Maintenance Trouble shooting

1 2-4

5-12 13-14

Cautions

The machine is adaptive in following situation

I. Applicable ambient temperature range:

Indoor

Cooling

Outdoor

Indoor

Heating

Outdoor

Maximum: D.B / W.B 32 Minimum: D.B / W.B

Maximum: D.B Minimum: D.B Maximum: D.B

Minimum: D.B Maximum: D.B / W.B Minimum: D.B / W.B

2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person. The type of connecting wire is H05RN-F or H07RN-F

3. If the fuse on PC board is broken please change it with the type of T. 3.15A/250V.

4. The distance between the indoor unit and the floor should be more than 2m.

5. The wiring method should be in line with the local wiring standard.

6. After installation, the power plug should be easily reached.

7. The waste battery should be disposed properly.

8. The appliance is not intended to use by young children or infirm persons without supervision.

9.Young children should be supervised ensure that they do not play with the appliance.

10.The appliance must be installed on strong enough supporter.

11.The wiring diagram is attached inside the machine.

C/23oC

18oC/14oC

C/26oC

C/18oC

C/-8oC

-7

Parts and Functions

Indoor Unit

Inlet grille

Air filter

Vertical flap

Use remote controller to adjust up and down air flow. (Don't adjust it manually.)

HSU-07HC03/R2 HSU-07HE03/R2 HSU-09HC03/R2 HSU-09HE03/R2 HSU-12HE03/R2 HSU-12HC03/R2 HSU-14HB03/R2 HSU-18HB03/R2

Power indicator

Lights up when unit starts.

Timer mode indicator

Lights up when Timer operation is selected.

Test running switch(manual)

Used only for test running in cooling when room temp. is below 16 Don't use it in normal operation.

Emergency switch(manual)

Used when remote controller is lost or defective. Unit will run temporarily.

Remote signal receiver

A beeping sound is generated when a signal from remote controller is received.

Operation mode indicator

Lights up during compressor running.

HSU-09HD03/R2 HSU-12HD03/R2

HSU-07HD03/R2

HSU-22HB03/R2 HSU-22HC03/R2 HSU-22HD03/R2

Actual inlet grille may vary from the one shown in the manual according to the product purchased

Outdoor Unit

HSU-07HC03/R2 HSU-07HE03/R2 HSU-07HD03/R2

HSU-18HB03/R2

HSU-09HE03/R2 HSU-12HE03/R2 HSU-09HD03/R2 HSU-12HD03/R2HSU-09HC03/R2

HSU-12HC03/R2 HSU-14HB03/R2

HSU-22HD03/R2 HSU-22HC03/R2 HSU-22HB03/R2

OUTLET

INLET

CONNECTING PIPING AND ELECTRICAL WIRING

DRAIN HOSE

Parts and Functions

Operation

2 3

13 14

Clock set

ON/OFF

MODE SET

FAN

SWING

SLEEP

LOCK RESET

Buttons and display of the remote controller.

1. Mode display AUTO

COOL DRY HEAT

5 6

A U T O

ON OFF

TEMP

TIMER

CLOCK

18 19

FAN

2. SWING display

3. FAN SPEED display

4. SLEEP display

5. LOCK display

6. SIGNAL SENDING

7. TIMER OFF display

8. TIMER ON display

9. CLOCK display

10. TEMP display

11. POWER ON/OFF

Used for unit start and stop.

12. MODE

Used to select AUTO run, COOL, DRY, HEAT and FAN operation

13. FAN

Used to select fan speed LO, MED, HI, AUTO

14. HOUR

Used to set clock and timer setting.

15. SWING

Used to set auto fan direction.

16. SLEEP

Used to select sleep mode.

17. LOCK

Used to lock buttons and LCD display.

18. TEMP.

Used to select your desired temp.

19. SET

Used to confirm timer and clock settings.

20. TIMER

Used to select TIMER ON, TIMER OFF, TIMER ON-OFF

21. CLOCK

Used to set correct time

22. RESET

Used to reset the controller back to

normal condition.

When unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows: Press CLOCK button, "AM" or "PM" flashes. Press or to set correct time. Each press will increase or decrease 1min. If the button is kept depressed, time will change quickly. After time setting is confirmed, press SET, "AM "and "PM" stop flashing, while clock starts working.

NOTE: Cooling only unit do not have displays and functions related with heating

LO MED HIAUTO

Hints

After replacing with new batteries, remote controller will conduct self-check, displaying all information on LCD. Then, it will become normal.

Parts and Functions

Operation

Buttons and display of the remote controller.

If the unit which you purchased has healthy function, Remote controller should

like the following figure:

2 3

A U T O

OFF

ON/OFF TEMP

MODE SET

13 14

FAN TIMER

SWING CLOCK

SLEEP

HEALTH

LOCK RESET

BRIEF INTRODUCTION TO HEALTH OPERATION

The anion generator in the air conditioner can generate a lot of anion to effectively balance the quantity of position and anion in the air and also to kill bacteria and speed up the dust sediment in the room and finally clean the air in the room.

NOTE: Cooling only unit do not have displays and functions related with heating

5 6

18 19

1. Mode display AUTO

COOL

DRY

HEAT

FAN

2. SWING display

3. FAN SPEED display

4. SLEEP display

5. LOCK display

6. SIGNAL SENDING

7. TIMER OFF display

8. TIMER ON display

9. CLOCK display

10. TEMP display

11. POWER ON/OFF

Used for unit start and stop.

12. MODE

Used to select AUTO run, COOL, DRY, HEAT and FAN operation

13. FAN

Used to select fan speed LO, MED, HI, AUTO

14. HOUR

Used to set clock and timer setting.

15. SWING

Used to set auto fan direction.

16. SLEEP

Used to select sleep mode.

17. LOCK

Used to lock buttons and LCD display.

18. TEMP.

Used to select your desired temp.

19. SET

Used to confirm timer and clock settings.

20. TIMER

Used to select TIMER ON, TIMER OFF, TIMER ON-OFF

21. CLOCK

Used to set correct time

22. RESET

Used to reset the controller back to normal condition.

23. HEALTH

Used to set healthy operation

AUTO

MED

Hints

After replacing with new batteries, remote controller will conduct self-check, displaying all information on LCD. Then, it will become normal.

Operation

Remote controller's operation

When in use, put the signal transmission head directly to the receiver hole on the indoor unit.

The distance between the signal transmission head and the receiver hole should be within 7m without any obstacle as well.

Don't throw the controller, prevent it from being damaged. When electronic-started type fluorescent lamp or change-over

type fluorescent lamp or wireless telephone is installed in the room, the receiver is apt to be disturbed in receivering the signals so the distance to the indoor unit should be shorter.

Loading of the battery

Load the batteries as illustrated. 2 R-03 batteries, resetting key (cylinder)

Remove the battery cover:

Slightly press " " and push down the cover.

Load the battery:

Be sure that the loading is in line with the" + "/"-" pole request as illustrated.

Put on the cover again Confirmation indicator:

In disorderation, reload the batteries or load the new batteries after 6mins.

Note:

Use two new same-typed batteries when loading. If the remote controller can't run normally or doesn't work at all, use a sharp pointed item to press the reset key.

Hint:

Remove the batteries in case unit won't be in usage for a long period. If there are any display after taking-out just need to press reset key.

Power failure resume(please set and apply as necessary)

If sudden power failure occurs, the unit will resume original operation when power is supplied again.

Note:

When sudden power failure happens during unit operation in power failure resume mode, if the air conditioner is not desired for use in a long period, please shut off the power supply in case that the unit automatically resume operation when power is re-supplied, or press ON/OFF to turn off the unit when power resumes.

Operation

Auto run, Fan operation

Enjoy yourself by just a gentle press.

(1) Unit start

Press ON/OFF button, unit starts. Previous operation status appears on display. (Not Timer setting) Power indicator on indoor unit lights up.

(2) Select operation mode

Press MODE button. For each press, operation mode changes as follows:

AUTO COOL DRY HEAT FAN

Unit will run in selected mode. Stop display at " " AUTO or " "FAN.

(3) FAN

Press FAN button. For each press, fan speed changes as follows:

ON/OFF TEMP

MODE

FAN

CLOCKSWING

SLEEP

LOCK

SET

TIMER

RESET

AUTO LO MED HI

(4) Unit stop

Unit will run at selected fan speed. Note:AUTO is not available in FAN mode.

Press ON/OFF button. Only time remains on LCD. All indicators on indoor unit go out. Vertical flap closed automatically.

Hints

Remote controller can memorize settings in each operation mode. To run it next time just select the operation mode and it will start with the previous setting. No reelecting is needed.(TIMER ON/OFF needs reelecting)

Cautions: Note: On cooling only unit, heating mode is not available, The above information is the

After replacing batteries, press ON/OFF, and display explanation of the displayed becomes as follows: information therefore varies Operation mode: AUTO, Temp. No with those displayed in actual Timer mode: No, Fan speed :AUTO operation.

+ 18 hidden pages