Haier HPU-18H03/HBF, HPU-24H03/HBF Operation Manual

PACKAGED TYPE ROOM AIR CONDITIONER OPERATION MANUAL

CONTENTS

PARTS AND FUNCTIONS

OPERATION

INSTALLATION

MAINTENANCE

2-3

4-5

6-9

The image shown here is indicative only, The actual product may differ

ΕΎϳϮΘΤϤϟ΍

ĂĂĂĂĂ

˯΍ΰΟϷ΍ΎϬϔ΋Ύχϭϭ

ĂĂĂĂĂ

ΔϧΎϴμϟ΍

ΔϴΑήόϟ΍

English

0010564839

Parts and Functions

Indoor Unit

FRONT OUTLET

CONTROL PANEL

FRONT BOARD

LEFT&RIGHT INLET

(AIR FILTER AND PROTECTING WIRE NET INSIDE)

LOWER INLET

(AIR FILTER AND PROTECTING WIRE NET INSIDE)

Outdoor Unit

MODE

INLET DRAIN HOSE

OUTLET

CONNECTING PIPING

AND ELECTRICAL WIRING

INLET

Fuzz display

COOL display

Dehu display

AMBIENT TEMP &SET TEMP display

FAN display

HEAT display

FAN SPEED display

TURBO/QUIET display

NEGATIVE ION display

Sleep display

TIMER ON/OFF display

Loading of the battery

Loading the batteries as illustrated. 2 R-03 batteries, resetting key(cylinder)

Remove the battery cover;

Load the battery: Be sure that the loading is in

line with the “+/-”pole request as illustrated.

Put on the cover again

Confirm indicator In disorderation, Reload the

batteries or load the new batteries after 6 mins.

Note:

Remove the batteries in case that unit won’t be in usage for a long period. If there are any display after taking-out just need to press reset key.

Remote controller

TURBO button COOL button AUTO button FAN SPEED button TIMER button SLEEP button LOCK button

LIGHT button POWER ON/OFF button DRY button TEMP button SWING button HOUR button EXTRA FUNCTION button CONFIRM/CANCEL button RESET button HEAT button

Remote controller Display

FAN display

DRY display

COOL display MODE display

Signal sending display

SWING display

FAN SPEED display

QUIET display

TIMER ON display& TIMER OFF display &SLEEP display

Elec Heat display

Negative Ion display

TURBO display

TEMP display

HEAT display

NOTE: The unexplained buttons and displays is not available for the unit.

Remote controller’s operation

When in use, put the signal transmission head directly to the receiver hole on the indoor unit.

The distance between the signal transmission head and the

receiver hole should be within 7m without any obstacle as well

Don’t throw or knock the remote controller

When electronic-started type fluorescent lamp or change-over type fluorescent lamp or wireless telephone is installed in the room, the receiver is apt to be disturbedin receiving the signals, so the distance to the indoor unit should be shorter.

NOTE

Use two same typed batteries when loading. If the remote controller can’t run normally during operation, please remove the batteries and reload several minutes later. False or unclear display during operation indicates the batteries have been used up. please change batteries. The waste battery should be disposed properly.

Display Board

TURBO

SLEEP



HEAT

Operation

Base Operation

Unit start

Press ON/OFF on the indoor unit ,or press ON/OFF on the remote controller,unit starts.

The liquid crystal will display the working state of last time (Except Timer and Sleep )

Select operation mode

Press HEAT,DRY,COOL ,or AUTO button,For each

Fan speed selection

Press FAN button. For each press,fan speed changes as follows:

Remote controller:

LOW

MED

AUTO

Display circulated

Air conditioner is running under displayed fan speed. When FAN is set to AUTO,the air conditioner automatically

adjusts the fan speed according to room temperature.

Unit stop

Press ON/OFF button, the unit stops.

Control panel display

Auto Operation

Fuzz

AUTO

COOL Operation

COOL

HIGH

DRY Operation

AUTO

Dehu

FAN Operation

LOW

FAN

HEAT Operation

HEAT

LOW

Remote controller button

Air Flow Direction Adjustment

Up and down air flow direction display

Pos.1

Pos.2

Pos.3

Pos.4

Pos.5

Pos.1 Pos.1

Pos.1

Pos.2

Pos.3

Pos.4

Pos.5

Pos.6

Pos.7

Pos.8

Left and right air flow direction display

Fig.1

Fig.2

Fig.3

Fig.4

(Auto swing)

Horizontal flap

Vertivcal flap

Sleep Operation

Operation Mode

In COOL,DRY mode

1 hours after SLEEP mode starts, temp. will become 1

for further 6 hours then stops. Temp. is higher than temp.setting so that room temperature won’t be too low for your sleep.

In HEAT mode

1 hours after SLEEP mode starts, temp. will become 2

for further 3 hours then stops. Temp. is lower than temp.setting so that room temperature won’t be too high for your sleep.

In FAN mode

It has no SLEEP function.

Temp.setting

SLEEP operation starts

Rises 1

Unit stop

SLEEP operation stops

In HEAT mode

In COOL DRY mode

SLEEP operation stops

SLEEP operation starts

Temp.setting

Unit stop

Rises 1

Decreases 2

Remote controller display

Up and down air flow direction adjustment

For each press of SWING button,the position of horizontal flap and the air flow direction on remote controller display changes as follows according to different operation models:

COOL/DRY/FAN

HEAT/AUTO mode

Remote controller

Horizontal flap

Pos.1

Pos.2

Pos.3

Pos.4

Pos.5

Pos.1

Pos.2

Pos.3

Pos.4

Pos.5

(Fig.1)

(Fig.3)

Note:When the unit is turned off by the remote controller or the control panel,the horizontal flap will close. When the power supply is cut off directly, the horizontal flap will not close. Please use the remote controller or the control panel to stop the unit.Do not start or stop the operation by disconnecting the power supply and so on

HEALTH Operation

Note:

When the HEALTH mode is set, the flap will keep the position you set.

It is advisable not to keep horizontal

flap at downward positionfor a long time in COOL or DRY mode,otherwise,condensate water might occur.

Remote controller

Vertical

flap

Pos.1

Pos.2

Pos.3

Pos.4 Pos.5

Pos.6

Pos.7

Pos.8

Pos.1

Pos.2

Pos.3

Pos.4

Pos.5

Pos.6

Pos.7

Pos.8

(Fig.2)

(Fig.4)

ć

TURBO

SLEEP

TURBO

Press button to enter additional options, when cycle display to

will flash, and then press

,enter to health function. When cancel the

function, please enter additional options again and to cancel health function.

press,operation mode changes.

Press button to enter additional options, when cycle display to

will flash. And then press , enter to Left and right air flow function.

Press . For each press, move the vertical blade by a knob on air conditioner

to adjust left and right direction referring to Fig. displays as follows:

Left and right air flow adjustment



Operation

Timer On/Off On-Off Operation

1.After unit starts, select your desired operation mode.

2.Press TIMER button to change TIMER mode. Every

time the button is pressed, display changes as follows:

Remote controller:

BLANK

TIMER ON TIMER OFF TIMER ON-OFF

Then select your desired TIMER mode (TIMER ON or

TIMER OFF or TIMER ON-OFF). " "or " "will flash.

3.Press / button to set time.

It can be adjusted within 24 hours.

Hints:

After replacing batteries or a power failure happens, time setting should be reset. According to the Time setting sequence of TIMER ON or TIMER OFF, either Start-Stop or Stop-Start

TIMER OFF-ON

0.5h

0.5h 0.5h

0.5h

Press the button for each time, setting time in the

first 12 hours increased by 0.5 hour every time,

after12 hours,increased by 1 hour every time. Press the button for each time, settiing time in the first 12 hours decreased by 0.5 hour every time, after 12 hours,decreased by 1 hour every time.

After adjust the time,press button and confirm

the time ON or OFF button will not flash any more.

4.Confirm timer setting

5.Cancel timer setting

Press the timer button by times until the time display

eliminated.

can be achieved.

Healthy airflow Operation

TURBO/QUIET Operation

(1)

TURBO Operation

Note

During POWER operation, in rapid HEAT or COOL mode, the room will show inhomogeneous temperature distribution.

Long period QUIET operation will cause effect of not too

cool or not too warm.

Power failure resume

(please set and apply as necessary)

With setting of power failure resume, if sudden power failure occurs,the unit will resume original operation when power is supplied again. Setting method: With ON of remote controller (except TIMER and SLEEP),repeateadly press SLEEP button 10 times in 5 seconds ,after 4 beep from the buzzer,the unit comes into power failure resume mode. To cancel: press SLEEP button continuously 10 times in 5 seconds,the buzzer sounds beep twice and power failure resume function is canceled.

Note:

1.When sudden power failure happens during unit operaition in power failure resume mode,if the air conditioner is not desired for use in a long period please shut off the power supply in case that the unit automatically resume operation.

2.when power is re-supplied,or press ON/OFF to turn off the unit when power resumes.

1.Press to starting

Setting the comfort work conditions.

2.The setting of healthy airflow function

Note:

1.After setting the healthy airflow function, the position

grill is fixed.

3.In cooling and dry, using the air conditioner for a long time under the high air humidity, condensate water may

occur at the grille .

3.The cancel of the healthy airflow function

Notice: Do not direct the flap by hand. Otherwise, the grille will run incorrectly. If the grille is not run correctly, stop for a minute and then start, adjusting by remote controller.

2.In cooling, it is better to select the mode.

Press button to enter additional options,Press this

button continuously, the louvers location will cycle between

in the following three locations, to choose the swing location

what you needed,and then press button to confirm.

Press button to enter additional options,Press this

button continuously, the louvers location will cycle between

in the following three locations again,and then press button to cancel.

Healthy airflow upwarder

Healthy airflow downwarder

Present position

ON OFF

(2)

QUIET Operation

When you need rapid cooling, you can use this function.

You can use this function when silence is needed for rest or

reading .Press button, when cycle display to

will flash, and then press

Press TURBO button, the remote controller will show

，

and then achieve to the turbo function. Press again this TURBO button, the turbo function will be canceled.

,enter to quiet function.

When cancel the function,please enter additional options again and to cancel the quiet function.



+ 11 hidden pages

Haier HPU-18H03/HBF, HPU-24H03/HBF Operation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual