Haier HPU-18H03, HPU-18C03, HPU-24C03, HPU-24H03 Operation Manual

PACKAGED UNIT

OPERATION MANUAL

Please read this operation manual

before using the air conditioner

.

0010519818

HPU-18C03/E1
HPU-24C03/E1
HPU-18H03/E1
HPU-24H03/E1

Cautions

Disposal of the old air conditioner

Before disposing an old air conditioner that
goes out of use, please make sure it's
inoperative and safe. Unplug the air
conditioner in order to avoid the risk of

child

entrapment.

It must be noticed that air conditioner
system contains refrigerants,which require
specialized waste disposal. The valuable
materials contained in an air conditioner

can
be recycled. Contact your local waste
disposal center for proper disposal of an
old air conditioner and contact your local
authority or your dealer if you haveany
question. Please ensure that the pipework
of your air conditioner does not get

damaged
prior to being picked up by the relevant
waste disposal center, and contribute to
environmental awareness by insisting on
an appropriate, anti-pollution method of
disposal.

Disposal of the packaging of your
new air conditioner

All the packaging materials employed in

the

package of your new air conditioner may

be
disposed without any danger to the
environment.

The cardboard box may be broken or cut

into
smaller pieces and given to a waste paper
disposal service. The wrapping bag made of
polyethylene and the polyethylene foam pads

All these valuable materials may be taken
to

a waste collecting center and used again

after adequate recycling.

Consult your local authorities for the name
and address of the waste materials
collecting centers and waste paper disposal
services nearest to your house.

Safety Instructions and Warnings

Before starting the air conditioner, read the
information given in the User's Guide
carefully. The User's Guide contains very
important observations relating to the
assembly, operation and maintenance of
the air conditioner.

The manufacturer does not accept
responsibility for any damages that may
arise due to non-observation of the following
instruction.

Damaged air conditioners are not to be

put into operation. In case

of doubt, consult

your supplier.

Use of the air conditioner is to be carried

out in strict compliance with the relative
instructions set forth in the User's Guide.

Installation shall be done by professional

people, don't install unit byyourself.

For the purpose of the safety,the air conditioner

must be properly grounded in accordance

with specifications.

Always remember to unplug the air

conditioner before openning inlet grill. Never
unplug your air conditioner by pulling on
the power cord. Always grip plug firmly and
pull straight out from the outlet.

All electrical repairs must be carried out
byqualified electricians. Inadequate repairs
may result in

amajor source of danger for

the user of the air conditioner.

Do not damage any parts of the air
conditioner that carry refrigerant by piercing
or performating the air conditioner's tubes

with sharp or pointed items

, crushing or

twisting any tubes

, or scraping the coatings

off the surfaces. If the refrigerant spurts
out and gets into eyes

, it may result in

serious eyeinjuries.

1

Cautions

Do not obstruct or cover the ventilation
grille of the air conditioner. Donotput
fingers or any other things into the
inlet/outlet and swing louver.

Do not allow

children to playwith the air
conditioner. In no case should children be
allowed to sit on the outdoor unit.

Specifications

The refrigerating circuit is leak-proof.

1. Applicable ambient temperature range:

2. If the power supply cord is damaged, it
must be replaced by the manufacturer
or its service agent or a similar qualified
person.

3. If the fuse on PC board is broken,please
change it with the type of T. 3.15A/ 250V.

4. The wiring method should be in line with
the local wiring standard.

5. After installation, the power plug should

be easily reached.

6. The waste battery should be disposed
properly.

7. The appliance is not intended for use by
young children or infirm persons without
supervision.

8. Young children should be supervised to
ensure that they do not playwith the
applience.

9. A breaker should be used in the circuits,

which should be all

-pole cutoff and the

distance between its two contacts should
be not at least 3mm .

10.Please employ the proper power plug,

which fit into the

power supply cord.

11.The power plug must haveacquired the

local attestation.

The machine is adaptive in following
situation

Cooling

Indoor

Outdoor

Maximum: D.B/W.B 32°C

/ 23°C

Minimum: D.B/W.B 18°C / 14°C

Maximum: D.B/W

.B 43°C / 26°C

Minimum: D.B 18°C

Maximum

: D.B 27°C

Minimum:

Minimum:

D.B 15°C

Maximum: D.B/W

.B 24°C / 18°C

D.B/W.B-7°C/-8°C

2

Indoor

Outdoor

Heating

Cautions

Please read the following SafetyInstructions carefully prior to use.

The instructions are classified into twolevels, WARNING and CAUTION according to the

seriousness of possible risks and damages as follows. Compliance to the instructions are

strictly required for safety use.

Safety Instruction

Installation

WARNING

Please call Sales/Service Shop for the Installation.

Do not attempt to install the air conditioner byyourself because improper worksmay
cause electric shock, fire,water leakage.

CAUTION

Installation in an inadequate place may cause accidents. Do not install in the following place.

Connect the earth

cable.

PROHIBITION PROHIBITION

STRICT

ENFORCEMENT

Do not install in the

place where there
is any possibilit y
of inflammable
gas leakage around
the unit.

Do not get the unit
exposed to vapor
or oil steam.

Check proper
installation of the
drainage securely

Use fuse with specified capacity.
Replacement with steel or copper wires are
absolutely prohibited.

Grounding wire should not be connected to

that of gas pipeline,water pipeline,lighting
arrester or telephone.

FUSE

STEEL WIRE

COPPE

RWIRE

3

When abnormality such as burnt-small found, immediately
stop the operation button and contact sales shop.

Connect power supply cord to the
outlet completely.

After installed, the unit shall be
tested for electric leakage.

Take

care not to damage the

power supply cord.

Do not use power supply cord in
a bundle.

Donotusepower supply cord
extended or connected in halfway.

Do not insert objects into the air
inlet or outlet.

Do not try to repair or reconstruct
byyourself.

PROHIBITION

PROHIBITION

PROHIBITION

PROHIBITION

PROHIBITION

OFF

STRICT

ENFORCEMENT

STRICT

ENFORCEMENT

Use an exclusivepower source with a circuit breaker.

CAUTION

Do not use for the purpose of

storage of food, art work, precise
equipment,

breeding , or cultivation.

Take fresh air occasionally
especiallywhen gas appliance is
running at the same time.

Do not operate

the switch with wet

hand.

Do not pour water onto the unit
for cleaning.

Check good condition of the
installation stand.

Do not install

the unit near a fireplace

or other heating apparatus.

Do not place animals or plants in
the direct path of the air flow.

Do not place any objects on or
climb on the unit.

Do not place flower vase or water
containers on the top of the unit.

PROHIBITION

PROHIBITION

PROHIBITIONPROHIBITION

PROHIBITION

PROHIBITION

PROHIBITION

PROHIBITION

STRICT

ENFORCEMENT

Cautions

WARNING

Use of Air Conditioner

Do not channel the air flow directly
at people, especially at infants or
the aged.

Do not start or stop the operation
by disconnecting

the power supply

cord and so on.

PROHIBITION

4

Parts and Functions

Outdoor unit

Indoor unit

1.OUTLET

2.CONTROL PANEL

4.INLET

3.INLET GRILLE

2.INLET 4.DRAIN HOSE

1.OUTLET 3.CONNECTING PIPING AND ELECTRICA

L WIRING





5

HPU-18C03/E1
HPU-18H03/E1

HPU-24C03/E1
HPU-24H03/E1

Operation mode

AUTO FANCOOLDRY

Remote controller

Display board

18.Singal sending display

When the remote controller appears abnormal,
use a sharp pointed article to press this button
to reset the remote controller normal.

1. RESET

Used to select TIMER ON, TIMER OFF,
TIMER ON-OFF.

3. TIMER button

Used to set correct time.

4. CLOCK button

Used to select sleep mode.

25. . SLEEP button

6. MODE button

Used to set clock and timer setting.

7. HOUR button

Used to set healthy operation.

5. HEALTH button

Used for unit start and stop.

9. ON/OFF button

10. TIMER ON display

11. FAN SPEED display

12. LOCK displa

y

13. SWING UP/DOWN display

14. SLEEP display

15. HEALTH display

16. E.HEAT display

Used to select your desired temperature.

17. Operation mode display

19. Left/right air flow display

Remote controller: to display the TEMP. setting.

20. TEMP display

21. TIMER OFF display

23. TEMP button

Used to select fan speed: LOW,MED, HI, AUTO.

24. FAN button

8. SWING UP/DOWN button

Used to select up or down air sending direction.

Used to confir

m timer and clock settings.

26. SET button

Used to loc

k b

uttons and LED displa

y. If pressed, the

other b

uttons will be disabled and the loc

k condition

display appears

. Press it once again, lock will be

canceled and lock condition display disappears.

28.

LOCK

22. TIMER display

Remote controller

LOW HI

MED AUTO

19

2. LIGHT button

Control the lightening and extinguishing of
the indoor LED display board.

6

20

15

17

28

14

E.HEAT

HEAT

AUTO COOLDRY FAN

HEAT

28

Used to operate electricity

heat

function.

27.

E.HEAT button

B

A

Control panel: See p17

NOTE:(1) The following functions and related displays are not available:

(2) Cooling only unit do not have functions and displays related with heating

.

5

(3)The air conditioner you bought, may not include the E.Heat function, is subject to the actual product.

Parts and Functions

17.Singal sending display

When the remote controller appears abnormal,
use a sharp pointed article to press this button
to reset the remote controller normal.

1. RESET

Used to select TIMER ON, TIMER OFF,
TIMER ON-OFF.

3. TIMER button

Used to set correct time.

4. CLOCK button

Used to select sleep mode.

24. . SLEEP button

6. MODE button

Used to set clock and timer setting.

7. HOUR button

Used to set healthy operation.

5. HEALTH button

Used for unit start and stop.

9. ON/OFF button

10. TIMER ON display

11. FAN SPEED display

12. LOCK displa

y

13. SWING UP/DOWN display

14. SLEEP display

15. HEALTH display

Used to select your desired temperature.

16. Operation mode display

18. Left/right air flow display

Remote controller: to display the TEMP. setting.

19. TEMP display

20. TIMER OFF display

22. TEMP button

Used to select fan speed: LOW,MED, HI, AUTO.

23. FAN button

8. SWING UP/DOWN button

Used to select up or down air sending direction.

Used to confir

m timer and clock settings.

25. SET button

Used to lock buttons and LED display. If pressed, the
other buttons will be disabled and the lock condition
display appears. Press it once again, lock will be
canceled and lock condition display disappears.

26. LOCK

21. TIMER display

Remote controller

Control panel: See p17

LOW HI

MED AUTO

19

2. LIGHT button

Control the lightening and extinguishing of
the indoor LED display board.

7

19

15

16

26

14

Operation mode

AUTO FANCOOLDRY

Remote controller

Display board

AUTO COOLDRY FAN

B

A

NOTE:(1) The following functions and related displays are not available:

(2) Cooling only unit do not have functions and displays related with heating

.

5

Parts and Functions

Remove the batteries in case unit won't be in usage for a long period. If there are any display
after taking-out, just need to press reset key.

Clock Set

When unit is started for the first time and after replacing batteries in
remote controller, clock should be adjusted as follows:

Remote controller's operation

3. After time setting is confirmed, press SET, "AM" or "PM" stop flashing,
while clock starts working.

2. Press or to set correct time. Each press will increase or decrease
1 min. If the button is kept depressed, time will change quickly.

1. Press CLOCK button,"AM" or "PM" flashes.

When in use, put the signal transmission head directly to the receiver hole on the indoor unit.

The distance between the signal transmission head and the receiver hole should be within
7m without any obstacle as well.

Don't throw or knock the remoter controller.

When electronic-started type fluorescent lamp or change-over type fluorescent lamp or
wireless telephone is installed in the room, the receiver is apt to be disturbed in receiving
the signals, so the distance to the indoor unit should be shorter.

Loading of the battery

Load the batteries as illustrated right
2 R-03 (7#) batteries

Remove the battery cover:

Slightly press" "area and push down the cover
as illustrated.

Load the battery:

Be sure that the loading is in line with the "+" / "-".
request as illustrated on the bottom of the case.

Put on the cover again.

Confirmation indicator:

After pressing power ON/OFF, if no display, reload the batteries.

Note:

Full display or unclear display during operation indicates the batteries have been used up.
Please change batteries.

Used two new same-typed batteries when loading.
If the remote controller can't run normally during operation, please remove the batteries and

reload several minutes later.

Hint:

8

E.HEAT

Parts and Functions