Haier HLC32K2, HLC32K2a Owner's Manual
HLC32K2
01
0090509706
LCD HDTV
Please READthismanual carefully before
operating yourTV,and retain it for future
reference.
OWNER’S MANUAL
Warning
EN-1 Haier LCD HDTV/DVD
CAUTION
!
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
RISK ELECTRIC SHOCK
DO NOT OPEN
!
The lightning flash with arrowhead
symbol, within an equilateral triangle is
intended to alert the user to the presence
of uninsulated dangerous voltage within
the product’s enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN EXTENSION
CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO
PREVENT BLADE EXPOSURE.
!
Caution:
These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do q
not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
Important Safety Instructions
Read t1. hese instructions.
Keep these instructions.2.
Heed all warnings.3.
Follow all instructions.4.
Do not use this apparatus near water.5.
Clean only with dry cloth.6.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.7.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including 8.
amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one 9.
wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the 10.
point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.11.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with 12.
the apparatus. When a cart is used, use caution when moving the cart/ Apparatus combination to
avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long periods of time.13.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has 14.
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, 15.
shall be placed on the apparatus.
The mains plug or appliance inlet is used as the disconnect device, remain it readily operable during the apparatus 16.
normal use.
Warning
Safety Instructions
Haier LCD HDTV/DVD EN-2
Class I apparatus shall be connected to a mains socket outlet with a protective earthing connection.
LASER SAFETY: This unit employs a laser. Only a qualified service person should remove the cover or attempt to
service this device, due to possible eye injury.
CAUTION: USE OF ANY CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO NOT STARE
INTO BEAM.
LOCATION: INSIDE, NEAR THE DECK MECHANISM.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rule. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, use and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However there is no guarantee that interference will not occur in particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encourage to try to correct the interference by one or more of the
following measures:
*Reorient or relocate the receiving antenna.
*Increase the separation between the equipment and receiver.
*Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
*Consult the dealer or an experienced radio/TV technician for help.
This device compiles with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may be not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired
operation.
FCC CAUTION:
To assure continued compliance and possible undesirable interference, the provided ferrite cores must be used
when connecting this LCD display to video equipment; and maintain at least 40cm spacing to other peripheral
device.
CANADIAN NOTICE:
This Class B digital apparatus compiles with Canadian ICES-003.
Safety Instructions
EN-3 Haier LCD HDTV/DVD
SAVE THESE INSTRUCTIONS
Thank you for purchasing the Haier product. This easy-to-use manual will guide you in getting the best use of your
product. Remember to record the model and serial number. They are on label in back of the unit.
Model number
serial number
Date of purchase
Staple your receipt to your manual. You will need it to obtain warranty service.
Contents
Haier LCD HDTV/DVD EN-4
Contents
How to Customize your own audio status................ 17
SAP Broadcasts Setup....................................................... 18
Function menu................................................... 18
Menu Language.................................................................. 18
OSD Timeout........................................................................ 18
OSD Transparency.............................................................. 18
DPMS ...................................................................................... 19
Blue Screen........................................................................... 19
DCR.......................................................................................... 19
Time Setup............................................................................ 19
Close Caption....................................................................... 19
Lock Menu..........................................................20
Parental Control rating and categories...................... 20
Lock setup............................................................................. 21
Other Functions.................................................23
Brief Info ................................................................................ 23
Using the Guide.................................................................. 23
Quick program view.......................................................... 24
CC (Closed Caption Display)........................................... 24
USB Input ...........................................................25
To play pictures................................................................... 25
To play music ....................................................................... 26
To play video........................................................................ 26
DVD Operation ..................................................29
Basic Playback ..................................................................... 29
Advanced Playback ...........................................................30
Special Function Playback .............................................. 30
DVD System Setup............................................................. 31
Playable Discs ...................................................................... 32
Discs Protection and DVD Characteristics................. 32
Maintenance 35
Specification 35
Troubleshooting 35
Warranty 36
Warning 1
Safety Instructions 3
Introduction 5
Controls................................................................5
Connection Options ............................................6
Universal Remote control ...................................7
Installation 8
External Equipment Connections ...................... 8
Accessories ..............................................................................8
Antenna Connection............................................................8
Choose Your Connection.................................................... 9
Connecting a VCR..................................................................9
External AV Source Setup...................................................9
Component Setup ................................................................9
Connecting a DTV (digital TV) ....................................... 10
Connecting a digital audio output .............................. 10
Connecting a computer................................................... 10
HDMI and DVI input .......................................................... 11
Connecting Headphones ................................................ 12
Power source........................................................................12
Removing the table stand and installing a wall
mount bracket .....................................................................12
Operation 13
Switching On/Off the TV set........................................... 13
Choose the Menu Language.......................................... 13
Choose the Input source .................................................13
Channel menu.................................................... 13
Channel Scan....................................................................... 13
Channel Skip ........................................................................ 14
Channel Labels.................................................................... 14
Time Shifting Mode........................................................... 14
Select the desired program............................................ 15
Select the desired sound................................................. 15
Mute........................................................................................ 15
Video menu........................................................15
How to select picture mode........................................... 15
How to customize your own picture status.............. 16
PC Set...................................................................................... 17
Audio menu........................................................17
How to select audio mode.............................................. 17
Introduction
EN-5 Haier LCD HDTV/DVD
Introduction
Controls
This is a simplified representation of the TV front panel, side panel control buttons and side inputs.
TV Side panel controls and connections
L- AUDIO - R
HDMI1 INHDMI2 IN USB
AV 1 IN
S-VIDEO
VIDEO
MEN
UI
N
PU
TVO
L
+VO
L
-C
H
+CH
-PO
WER
1
MENU
Menu display. Press to access the on-screen
menu display.
2
INPUT
Press to access the input source mode. Press
repeatedly to change the source to the one
you want to watch. In the MENU screen, the
INPUT button serves as the ENTER button.
3
VOL +/-
Press to adjust the volume. In the MENU screen,
these buttons serve as left/right buttons.
4
CH +/-
Press to scan through channels. To scan quickly
through channels, press and hold down either
+/- . In the MENU screen, these buttons serve
as up/down buttons.
5
POWER Press to turn on and off the TV.
6
USB input
Connect a USB ash drive to view MPEG2 videos,
JPEG images or listen to MP3 songs
.
7
Av2 AUDIO IN
Connect the audio L/R cables from the video
signal source to these jacks.
8
AV2 VIDEO IN
Connects the composite video cable from an
external signal source to this jack.
9
S-VIDEO
Connects the S-VIDEO cables from an external
signal source to this jack.
0
Headphone
jack
Headphone audio output terminal.
A
HDMI In
Connect a HDMI device to receive digital audio
and uncompressed digital video.
B
Remote Sensor
Receivers IR signals from the remote control.
Do not put anything near the sensor, which
may block the remote control signal.
DVD panel controls
L
a
b
elTowa
rdsBack
DVD slot load
STOP:
Press to stop the DVD disc.
PLAY/PAUSE:
Press to play the DVD program disc, and press again to pause
the DVD program.
OPEN/CLOSE:
Press to open the disc tray, and press again to close the tray.
PREV:
Press to play the previous program.
NEXT:
Press to play the next program.
Insert DVD with label
towards back (Silver “shiny”
side facing towards you.)
Introduction
Haier LCD HDTV/DVD EN-6
Connection Options
Back panel connections
PC/DVI
PC
PC IN
3
4
AV2 IN
1
Digital Audio
Output
Connect various types of digital audio equipment.
Note
In standby mode, these ports will not R
work.
2
Antenna
Input
Connect cable or antenna signals to the TV,
either directly or through your cable box.
3
HDMI In
Connect a HDMI device to receive digital audio
and uncompressed digital video.
4
PC Audio In
Connect the audio L/R cables from a computer
to this jack.
5
PC Video In
Connect a video cable from a computer to this
jack.
6
VIDEO In
Connects the video signal from a video device.
7
Component
Video In
Connect a component video device to these jacks.
8
AUDIO In
Connect the audio L/R cables from the video signal
source to these jacks.
9
COMPONENT
AUDIO In
Connect the audio L/R cables from the component
video signal source to these jacks.
0
AUDIO Out
Connect the audio L/R cables to your audio equipment.
Introduction
EN-7 Haier LCD HDTV/DVD
Remote control
The remote control cannot be operated unless the batteries are properly loaded.
When using the remote control, aim it at the remote sensor on the T V.
OPEN/CLOSE
PLAY/PAUSE
REV
D.MENU
SEARCH
D.CALL
ANGLE
D.AUDIO
SUBTITLE
ENTER
STOP REPEAT
PREV NEXT
SETUP
PROGRAM
USB
GUIDE
INPUT
MUTE
VOL CH
MENU
SLEEP DISPLAY
EXIT
RECALL
PICTURE AUDIO ARC FAVORITE
CCD MTS/SAP CH.LIST
DVD
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Function introduction
1
Power Press to turn on and o the TV
2
USB Press to switch input source to USB in
3
GUIDE
Display the guide when you are watching analog or digital channels
4
CCD (closed caption) Select a closed caption option
5
PICTURE Press repeatedly to cycle through the available picture modes
6
AUDIO Press to cycle through dierent sound settings
7
INPUT
Show the input source
8
MUTE
Switches the sound on or o
9
VOLUME UP/DOWN
Press to adjust the volume
0
MENU
Press to open the on-screen menu
A
Thumbstick (Up/Down/
Left/Right)
Allows you to navigate the on-screen menus and adjust the
system settings to your preference
B
SLEEP button
Press to display the sleep timer option
C
DVD/USB PLAY/PAUSE
D
DVD Open/close
E
DVD/USB FAST FORWARD
F
DVD/USB FAST REVERSE
G
DVD CALL
H
DVD MENU
I
DVD SEARCH
J
DVD ANGLE
K
DVD Mode
L
CH.LIST
Open the channel list in TV
M
MTS/SAP
Select MONO, STEREO, SAP in NTSC system
N
FAVORITE
Open the favourite channel list in TV
O
ARC
Select the aspect ratio
P
Number buttons Press to change a channel
Q
tCVUUPO
Press to select digital channels. For example, to enter “54-3”,
QSFTTiwitwBOEiw
R
RECALL Press to jump back and forth between two channels
S
CHANNEL UP/DOWN
Press to scan between the last two channels, press and hold
down either +/--
T
EXIT
Clears all on-screen displays and returns to TV viewing from any
menu
U
ENTER
Accesses the highlighted item in the on-screen menu
V
DISPLAY
Press to display the TV status information on the top of the TV screen
W
DVD/USB STOP
X
DVD/USB REPEAT
Y
D
VD/USB Previous Chapter
Z
DVD/USB Next Chapter
[
DVD AUDIO Mode
\
DVD SETUP
]
DVD PROGRAM
`
DVD SUBTITLE
Installation
Haier LCD HDTV/DVD EN-8
Installation
External Equipment Connections
Accessories
Remote control Owner’s manual Alkaline battery (AAA) x2
Antenna Connection
Over-the-air TV reception quality will depend on your antenna type, antenna location and antenna positioning.
ANT IN
VHF Antenna
UHF Antenna
Turn clockwise to tighten
Bronze Wire
Be careful not to bend thebronze wire
when connecting the antenna.
Bronze Wire
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
Wall Antenna
Socket
RF Coaxial Wire (75 ohm)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
Outdoor Antenna
To improve the picture quality in a poor signal
area, please purchase a signal amplifier and install
properly.
If the antenna needs to be split for two TV’s, install a
“2-Way Signal Splitter” in the connections.
To install the antenna properly please contact a
professional in your area.
Note
All cables shown are not included with the TV.R
3/$<3$86(
5(9
5(3($7
*8,'(
0766$3
&&' $5&
)5((=(
(17(5
6723 &(5%68
35(9 1(;7
&+/,67
)$925,7(
79
67%
,1387
087(
92/ &+
0(18
<$/36,'3((/6
(;,7
5(&$//
3,&785( $8',2 3& +'0,
&$%/( 9&5 $8'
'9'
ANT IN
Installation
EN-9 Haier LCD HDTV/DVD
Choose Your Connection
There are several ways to connect your television,
depending on the components you want to connect
and the quality of the signal you want to achieve. The
following are examples of some different ways to
connect your TV with different input sources.
Connecting a VCR
To avoid picture noise (interference), leave an adequate
distance between the VCR and TV.
How to connect
Connect the audio and video cables from the q
external equipment’s output jacks to the TV input
jacks, as shown in the figure.
When connecting the TV to external equipment, q
match the jack colors (Video = yellow, Audio Left =
white, and Audio Right = red).
Camcorder or video
game set
Video= yellow
Audio left= white
Audio right= red
Back of TV
AV2 IN
How to use
Select the input source with using the A INPUT button
on the remote control.
Press
B
/button to select the desired source.
Press
C ENTER button to confirm.
Operate the corresponding external equipment.
D
Component Setup
How to connect
Connect the DVD video outputs (COMPONENT) to the
Y Pb Pr jacks on the TV and connect the DVD audio
outputs to the YPbPr Audio IN jacks on the TV, as shown
in the figure.
Back of VCR
Back of TV
Video= yellow
Audio left= white
Audio right= red
AV2 IN
Connection Option 1
Set VCR output switch to channel 3 or 4 and then turn
the TV to the same channel number.
Connection Option 2
Connect the audio and video cables from the VCR’s A
output jacks to the TV input jacks, as shown in the
figure. When connecting the TV to VCR, match the
jack colors (Video = yellow, Audio Left = white, and
Audio Right = red). If you connect a S-VIDEO output
from VCR to the S-VIDEO input, the picture quality is
improved; compared to connecting a regular VCR to
the Video input.
Insert a video tape into the VCR and press
B PLAY on
the VCR. (Refer to the VCR owner’s manual.)
Select the input source with using the
C INPUT button
on the remote control, and then press
/button
to select the source, press ENTER button to confirm.
External A V Source Setup
Installation
Haier LCD HDTV/DVD EN-10
Component video device
Component video cable:
Green=Y
Blue=CB/PB
Red=CR/PR
Audio cable:
White=Left audio
Red=Right audio
Back of TV
How to use
Turn on the DVD player, insert a DVD disc.A
Use B INPUT button on the remote control to select
component mode.
Component Input portsQ
To get better picture quality, connect a DVD player to
the component input ports as shown below.
Component ports on the TV Y Pb Pr
Video output ports on DVD
player
Y
Y
Y
Y
Pb
B-Y
Cb
P
B
Pr
R-Y
Cr
P
R
Connecting a DTV (digital TV)
This TV can receive Digital Over-the-air/Cable signals
without an external digital set-top box. However, if you do
receive Digital signals from a digital set-top box or other
digital external device, refer to the figure as shown below.
This TV supports HDCP (High-bandwidth Digital Contents
Protection) protocol for Digital Contents (480 p,720 p,1080 i).
How to connect
Use the TV’s COMPONENT, VGA or HDMI jack for q
video connections, depending on your set-top box
connector. Then, make the corresponding audio
connections.
How to use
Turn on the digital set-top box. (Refer to the owner’s A
manual for the digital set-top box.)
Use INPUT on the remote control to select
B
COMPONENT, VGA or HDMI source.
Signal COMPONENT HDMI
480 i Yes Yes
480 p Yes Yes
720 p Yes Yes
1080 i Yes Yes
1080 p Yes Yes
Connecting a digital audio output
Send the TV’s audio to external audio equipment (stereo
system) via the Digital Audio Output (Optical) port.
How to connect
Connect one end of an optical cable to the TV Digital A
Audio (Optical) Output port.
Connect the other end of the optical cable to the
B
digital audio (optical) input on the audio equipment.
See the external audio equipment instruction
manual for operation.
Note
When connecting with external audio equipments, R
such as amplifers or speakers, please turn the TV
speakers off.
!
Caution:
Do not look into the optical output port. Looking q
at the laser beam may damage your vision.
Connecting a computer
How to connect
To get the best picture quality, adjust the VGA A
graphics card to 1024s 768.
Use the TV’s VGA or DVI (Digital Visual Interface) B
Audio IN port for audio connections, depending on
your computer connector.
If the graphic card on the computer does not q
output analog and digital RGB simultaneously,
Installation
EN-11 Haier LCD HDTV/DVD
connect only one of either VGA IN or HDMI IN to
display the VGA on the TV.
If the graphic card on the computer does output q
analog and digital RGB simultaneously, set the TV
to either VGA or HDMI; (the other mode is set to
Plug and Play automatically by the TV.)
Then, make the corresponding audio connection.
C
If using a sound card, adjust the VGA sound as
required.
Back of TV
PC/DVI
PC
PC IN
How to use
Turn on the computer and the TV.A
Use INPUT on the remote control to select VGA or B
HDMI source.
Check the image on your TV. There may be noise
C
associated with the resolution, vertical pattern,
contrast or brightness in VGA mode. If noise
is present, change the VGA mode to another
resolution, change the refresh rate to another rate
or adjust the brightness and contrast on the menu
until the picture is clear. If the refresh rate of the VGA
graphic card can not be changed, change the VGA
graphic card or consult the manufacturer of the VGA
graphic card.
Note
Use a DVI cable.R
Avoid keeping a fixed image on the TV’s screen R
for a long period of time. The fixed image may
become permanently imprinted on the screen.
The synchronization input form for Horizontal and R
Vertical frequencies is separate.
ResolutionY
Mode Resolution
Frame
frequency
(Hz)
VGA
640s480
60 Hz
SVGA
800s600
60 Hz
75 Hz
XGA
1024s768
60 Hz
75 Hz
HDMI and DVI input
When the source device (Blu-Ray player, DVD player
or Set Top Box) supports HDMI
How To Connect
Connect the source device to HDMI port of this TV A
with an HDMI cable (not supplied with this product).
No separated audio connection is necessary.
B
How To Use
Turn on the TV.q
Turn on the Blu- Ray player, DVD player or Set Top q
Box.
Select HDMI input source on the TV using the INPUT q
button or HDMI button on the remote control.
When the source device (DVD player or Set Top Box)
supports DVI
How To Connect
Connect the source device to HDMI port of this TV A
with a HDMI-to-DVI cable (not supplied with this
product).
A separated audio connection is necessary.
B
C
If the source device has an analog audio output
connector, connect the source device audio output to
DVI Audio In port located on the left side of HDMI port.
How To Use
If the source device supports Auto DVI function, q
the output resolution of the source device will be
Loading...