DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of
uninsulated dangerous voltage within the product s
enclosure that may be of sufficient magnitude to constitute a
risk of electric shock.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS
POLARIZED PLUG WITH AN EXTENSION CORD,
RECEPTACLE OR OTHER OUTLET UNLESS THE
BLADES CAN BE FULLY INSERTED TO PREVENT
BLADE EXPOSURE.
CAUTION: These servicing instructions are for use by qualified service
personnel only. To reduce the risk of electric shock, do not perform any
servicing other than that contained in the operating instructions unless
you are qualified to do so.
CAUTION: USE OF ANY CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE. (This item is only for TV with DVD models.)
IMPORTANT SAFETY INSTRUCTIONS
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves,
or other apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third
prong are provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long
periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
15)The apparatus shall not be exposed to dripping or splashing and that no
objects filled with liquids, such as vases, shall be placed on the apparatus.
16)The mains plug or appliance inlet is used as the disconnect device, remain it
readily operable during the apparatus normal use.
Safety Instructions(for TV with DVD)
PRECAUTIONS
FCC WARNING-This equipment may
generate or use radio frequency
energy.Changes or modifications to this
equipment may cause harmful
interference unless the modifications are
expressly approved in the instruction
manual.The user could lose the authority
to operate this equipment if an
unauthorized change or modification is
made.
LASER SAFETY
This unit employs a laser.Only a qualified
service person should remove the cover
or attempt to service this device,due to
possible eye injury.
CAUTION:USE OF CONTROLS OR
ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION
EXPOSURE.
CAUTION:VISIBLE AND INVISIBLE
LASER RADIATION WHEN OPEN AND
INTERLOCK DEFEATED.DO NOT
STARE INTO BEAM.
required when you are installing, using and cleaning this machine. To
your safety and extend the life-span of LCD-TV, please read the following items
carefully before using:
Please read and understand all the instructions before operation;
Please keep this manual for later use;
Please comply strictly with the warning instructions on the machine and
in this book;
Please comply with the instructions provided;
Please do not use additional devices that are not recommended by
manufacturer:
Before operation, please make sure that the operating voltage of your unit is
correct;
Do not place the unit on unstable, dusty and humid places;
Never put the unit in direct sunlight or near heat sources;
Allow enough space for proper ventilation;
Please keep water away from the LCD-TV . If water comes in contact with the
LCD-TV, disconnect the power cord from the power source, then wipe the set
with a dry soft cloth;
Do not remove the back cover. If service is needed, please contact an
Authorized service technician.
To prevent this, please do as
ensure
Front Panel Controls
T1 series
R1 series
23451
TV/AV MENU VOL- VOL+ CH- CH+ POWER
67
Control Panel Function
1. Power
2. TV/AV
3. MENU Press to select the main menu
4. VOL- Volume down / Left button to adjust the item in the OSD
VOL+ Volume up / Right button to adjust the item in the OSD
/Press to enter
5. CH- TV channel down / to select the item in the menu
CH+ TV channel up / to select the item in the menu
6. Power indicator
7. Remote Sensor
Selects the input signals.
Receives the signals from the remote control
Connection Options
DVD
STOP
PLAY/PAUSE OPEN/CLOSE
PREVNEXT
DVD insert
The above figure is for reference only, connections
Label towards back
Please see the real set
of the DVD position
ANT IN(Antenna Input)
Connect cable or
antenna signals to
the TV, either
directly or through
your cable box.
may differ depending upon the models and terminals
of some models may be on the back bottom of the set
S-VIDEO
Connect S-Video
out from an S-Video
device to the jacks.
Component Input
Connect a component
video device to these
jacks
Y
Pb
Pr
PC audio in
Connect the audio
output from the pc
to the PC audio
input port
VGAINPCAUDIOIN HDMI
L
AUDIO
R
S-VIDEO
VIDEOIN
RAUDIOINL
ANTIN
ANT IN
Headphone
Connect audio
output from an
external device
to these jacks
R AUDIO IN L
Audio in
VIDEO IN
S-VIDEO
Pr
R
Video in
Connect video
output from an
external device
to this jack
Audio in
Connect audio
output from an
external device
to these jacks
AUDIO
Y
Pb
L
VGA INPC AUDIO INHDMI
VGA
Connect to the VGA
15PIN analog output
connector of a PC
graphics card to use
set as a PC display
HDMI
Connect to HDMI
output of other
equipment
Remote Control
Installing Batteries
Remove the battery cover.
Insert two size AA batteries matching
the +/-polarities of the battery to the +/marks inside the battery compartment
(see image 1-for remote of TV with
DVD) ..
Insert two size AAA batteries matching
the +/-polarities of the battery to the +/marks inside the battery compartment
(see image 2-for remote of TV without
DVD) .
Image 1
Image 2
Precautions
Make sure that there is no
obstacle between the remote
controller and television set.
Keep the remote control
away from heat sources or
humid areas to ensure
effective performance of
the remote.
As strong light may interfere with the
signals, change your position to
operate the remote control if
the television cannot be turned
on or off as expected.
Make sure that two AA 1.5V or AAA
depending up the model alkaline
batteries are loaded. The batteries
must be of the same type, must be
inserted properly, and must not be
rechargeable.
Remote Control Key Functions
When using the remote control, aim it
towards the remote sensor on the TV
INFO
OPEN/CLOSE
MUTE
TV/AV
POWERTV/DVD
SLEEP Q.VIEW
1234
5678
CC
90
SAP
CH+
VOL
MENU
-
OKS.MODE
CH-
STOP
SETUP
REVFWDPREVNEXT
D.MENU
PLAY/ENTER
ANGLE
PROGRAM
AUDIO
10+
EXITARCGUIDE
CH.LIST FAV.LIST
(For TV with DVD)
P.M O DE
VOL
+
PAUSE/STEP
SUBTITLE
A-B
REPEAT
SLOW
TITLE/PBC SEA RCH
D.CALL
ZOOM
Buttons on the remote control
Power
DVD Open/close
Input selection
TV Sleep button
TV/DVD
Mute
Return to previous channel in TV mode
Program Infromation
Program Number
Select MONO,STEREO, SAP in NTSC system
CC( closed caption) On / Off
Select additional channels
Adjust Picture Mode
Volume/Channel Selection
MENU
Confirm button
Adjust sound mode
DVD STOP
DVD SUBTITLE
DVD SETUP
DVD PAUSE/STEP
DVD FAST REVERSE
DVD FAST FORWARD
DVD MENU
DVD Next Chapter
DVD Previous Chapter
DVD REPEAT
DVD PLAY/ENTER
DVD A-B REPEAT
DVD Cursor Move button
DVD SLOW
DVD ANGLE
DVD SEARCH
DVD AUDIO Mode
DVD TITLE/PBC
DVD PROGRAMZoom Function
DVD CALL DVD 10+
Exit On Screen Display
Select the aspect ratio
Shows program schedule in TV
Open the channel list in TV
Open the favourite channel list in TV
LEFT
UP
RIGHT
DOWN
Remote Control Key Functions
When using the remote control, aim it
towards the remote sensor on the TV
Buttons on the remote control
MUTE
Q.VIEWINFO
INPUTEXIT
SAPP.MODE
OK
CH+
VOL
MENU
-
CC
SLEEPS.MODE
GUIDEARCCH.LIST
FAV.LIST
CH-
VOL
+
Mute
Return to previous channel in TV mode
Input selection
Program Number
Select MONO, STEREO, SAP in NTSC system
Confirm button
Volume/Channel Selection
CC ( closed caption) On / Off
TV Sleep button
Shows program schedule in TV
Select the aspect ratio
Open the favorite channel list in TV
Open the channel list in TV
Adjust sound mode
MENU
Select additional channels
Adjust Picture Mode
Exit On Screen Display
Program Infromation
Power
(For TV without DVD)
Note: the instruction on this manual takes
remote of TV with DVD for example.
Connection Instructions
Grounding
Ensure that you connect the grounding / earth wire to prevent possible
electric shock. If grounding methods are not possible, have a qualified
electrician install a separate circuit breaker. Do not try to ground the
unit by connecting it to telephone wires, lightening rods, or gas pipes.
External Equipment Connections
Antenna Connection
- Antenna or Cable Service with a Cable Box Connections
- For optimum picture quality, adjust antenna direction if needed.
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
wall antenna
socket
RF coaxial wire (75 ohm)
Bronze Wire
VHF antenna
UHF antenna
outdoor
antenna
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
NOTE: Cables shown are not included with the TV
Turn clockwise to tighten.
Be careful not to bend the bronze
wire when connecting the antenna.
To improve picture quality in a poor
signal area, purchase and install a
signal amplifier.
If the antenna needs to be split for two
Tvs, install a 2-Way Signal Splitter
in the connections.
If the antenna is not installed properly,
contact your dealer for assistance.
Bronze Wire
Connection Instructions
VGA Setup
You can use your LCD-TV as a monitor for your personal computer using a VGA
cable (not supplied).
Connection and use steps:
1.Read the user guide supplied with
your computer and ensure that it has
a VGA connector;
2.Make sure that the power of the LCD
-TV and the PC are off;
3.Connect a D type 15-pin PC interface
cable ( not supplied ) to the PC video
interface connector on the PC. Then
connect the other end to the PC video
interface connector on the back of the
LCD-TV.Tighten the screws on the PC
connectors once they are firmly
connected;
4.Turn on the power of the LCD-TV first ,
and then turn on the power of the PC;
5.Press the TV/AV button to set the video input mode of the LCD-TV to PC;
Once the input for PC is selected and if you see no image press function
F8 on you pc.
6.Check the image on your TV. There may be noise associated with the resolution,
vertical pattern, contrast or brightness in PC mode. If noise is present, change
the PC mode to another resolution, change the refresh rate to another rate or
adjust the brightness and contrast on the menu until the picture is clear. If the
refresh rate of the PC graphic card can not be changed, change the PC graphic
card or consult the manufacturer of the PC graphic card.
Resolution
Mode
VGA
SVGA
XGA
Note: All above listed are subject to VESA criteria.
Resolution
640x480
800x600
1024x768
Line frequency(KHz)
31.5
37.9
48.4
Frame frequency(Hz)
60
60
60
Component Setup
How to connect
Connect the DVD video outputs (Y, PB, PR)
to the Component(Y, Pb, Pr) IN jacks on
the TV and connect the DVD audio outputs
to the AUDIO IN jacks on the TV, as shown
in the figure.
NOTE: If your DVD player does not have
component video output,use S-Video.
How to use
1. Turn on the DVD player, insert a DVD.
2. Use the button on the remote
control to select the proper input.
TV/AV
Connection Instructions
VCR Setup
- To avoid picture noise (interference), leave an adequate distance between the
VCR and TV
Connection and use steps:
1.Read the user guide supplied with your AV devices and ensure that it has
Composite or S-Video connectors;
2.Make sure that the power of the LCD-TV and the AV device are off;
Connection Option 1
Set VCR output switch to 3 or 4 and then
tune TV to the same channel number.
Connection Option 2
1. Connect the audio and video cables from
the VCR's output jacks to the TV input jacks,
as shown in the figure.
When connecting the TV to VCR, match
the jack colors (Video = yellow, Audio
Left = white,and Audio Right = red).
If you connect an S-VIDEO output from
VCR to the S-VIDEO input, the picture
quality is improved; compared to conne cting a regular VCR to the Video input.
2. Insert a video tape into the VCR and press
PLAY on the VCR. (Refer to the VCR owner s
manual.)
.
3
.Turn on the LCD-TV first ; and then turn on the
power of the AV device;
4.Press the TV/AV button to set
the video input mode of the
LCD-TV to S-Video mode or
Video mode.
1
2
VCR
HDMI Input
How to connect
Connect the cables from the external equipment's
output jacks to the TV input jacks, as shown in the figure.
How to use
1. Select the input source by using TV/AV button
on the remote control or on the TV.
2.
Operate the corresponding external equipment.
Refer to external equipment operating guide.
HDMI
Connection Instructions
Cable TV Setup
- After subscribing to a cable TV service from a local provider you can watch cable
TV programming. The TV cannot display TV programming unless a TV tuner
device or cable TV converter box is connected to the TV.
- For further information regarding cable TV service, contact your local cable TV
service provider(s).
Connection Option 1
1. Select 3 or 4 with channel switch on cable
box.
2. Tune the TV channel to the same selected
output channel on cable box.
3. Select channels at the cable box or with
the cable box remote control.
Connection Option 2
1. Connect the audio and video cables from
the Cable Box's output jacks to the TV
input jacks, as shown in the figure.When
connecting the TV to a Cable Box, match
the jack colors
(Video = yellow, Audio Left = white, and
Audio Right = red).
2. Select the input source by using the
button on the remote control.
3. Select your desired channel with the
remote control for cable box.
TV/AV
External Component Source Setup
How to connect
Connect the audio and video cables from
the external equipment's output jacks to the
TV input jacks, as shown in the figure.
When connecting the TV to external equipment, match the jack colors (Video = yellow,
Audio Left = white, and Audio Right = red).
How to use
1. Select the input source by using the
button on the remote control.
2. Operate the corresponding external equi-
pment. Refer to external equipment ope rating guide.
TV/AV
Loading...
+ 32 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.