Haier HEBF100BXS Installation and User Manual

Beverage Center Centre de boisson Centro de la bebida

Installation and User Manual

Instructions d’installation et

Guide de l’utilisateur

Instrucciones de instalación y

Manual del usuario

HEBF100BXS

ENGLISH

49-60809 Rev. 2 08-19 GEA

ENGLISH

49-60809 Rev. 2

TABLE OF CONTENTS

BEVERAGE CENTER SAFETY ................................................4

Proper Disposal of Your Old Appliance .......................................5

PARTS AND FEATURES ......................................................6

INSTALLATION REQUIREMENTS .............................................7

Location Requirements .....................................................7

Connecting Electricity ...................................................... 8

INSTALLATION INSTRUCTIONS .............................................9

Step 1 - Unpack Beverage center ............................................9

Step 2 - Door Reversing ....................................................10

Step 3 - Level the Beverage Center .........................................13

Step 4 - Complete Installation ..............................................13

BEVERAGE CENTER USE ..................................................14

Control ....................................................................14

Shelves ....................................................................14

Key Eject Lock .............................................................14

BEVERAGE CENTER CARE .................................................15

Cleaning ...................................................................15

Defrosting ............................................................... 16

Vacation and Moving .......................................................17

Reinstalling/Using Beverage center Again ...................................18

TROUBLESHOOTING ...................................................... 19

LIMITED WARRANTY ......................................................22

ENGLISH

RECORD KEEPING ........................................................2 4

49-60809 Rev. 2

ENGLISH

BEVERAGE CENTER SAFETY

IMPORTANT SAFETY INSTRUCTIONS

WARNING

center, follow basic precautions, including the following: Ŷ Use this appliance only for its

intended purpose as described in this user manual.

Ŷ This appliance must be properly

installed in accordance with the installation instructions before it is used. See grounding instructions in the installation section.

Ŷ Plug into a grounded 3 prong

outlet.

Ŷ Do not remove ground prong. Ŷ Do not use an adapter or

extension cord.

Ŷ Do not repair or replace any

part of the appliance unless specifically recommended in the manual. All other servicing should be referred to a qualified technician.

Ŷ Disconnect power before

servicing.

Ŷ Replace all parts and panels

before operating.

Ŷ Use nonflammable cleaner. Ŷ Keep flammable materials

and vapors away from the refrigerator.

To reduce the risk of fire, explosion, electrical shock,

injury to persons, or damage when using the beverage

Ŷ Do not store explosive

substances such as aerosol cans with a flammable propellant in this appliance.

Ŷ Before discarding or removing

from service, remove the door. This will reduce the possibility of danger to children.

Ŷ To avoid serious injury or death,

children should not stand on, or play in or with the appliance.

Ŷ Children and persons with

reduced physical, sensory or mental capabilities or lack of experience and knowledge can use this appliance only if they are supervised or have been given instructions on safe use and understand the hazards involved.

Ŷ This appliance is intended to be

used in household and similar applications such as: staff kitchen areas in shops, offices and other working environments; farm houses; by clients in hotels, motels, bed & breakfast and other residential environments; catering and similar non-retail applications.

CAUTION

To reduce the risk of injury when using your beverage

center, follow these basic safety precautions.

Ŷ Do not clean glass shelves or

covers with warm water when they are cold. Glass shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping or dropping. Tempered glass is designed to shatter into many small pieces if it breaks.

Ŷ Keep fingers out of the “pinch

point” areas; clearances between the door and cabinet are necessarily small. Be careful closing door when children are in the area.

ŶThis unit is designed for storing

and cooling beverages. Do not store perishable foods in this unit.

49-60809 Rev. 2

BEVERAGE CENTER SAFETY

WARNING

This appliance contains isobutane refrigerant, also known as R600a, a natural gas with high environmental compatibility. However, it is also combustible. Adhere to the warnings below to reduce the risk of injury or property damage.

1. When handling, installing and operating the appliance, care should be

taken to avoid damage to the refrigerant tubing.

2. Service shall only be performed by authorized service personnel. Use only manufacturer-authorized service parts.

3. Dispose of refrigerator in accordance with Federal and Local Regulations. Flammable refrigerant and insulation material used require special disposal procedures. Contact your local authorities for the environmentally safe disposal of your refrigerator.

4. Keep ventilation openings in the appliance enclosures or in the built-in structure clear of obstruction.

5. To remove frost, scrape with a plastic or wood spatula or scraper. Do not use an ice pick, metal, or sharp-edged instrument as it may puncture the freezer liner and then the flammable refrigerant tubing behind it.

6. Do not use electrical appliances inside the food storage compartment of the appliance.

7. Do not use any electrical device in defrosting your freezer.

FIRE OR EXPLOSION HAZARD

Flammable Refrigerant

ENGLISH

PROPER DISPOSAL OF YOUR OLD APPLIANCE

WARNING

Failure to follow these disposal instructions can result in death or serious injury.

IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned appliances are still dangerous even if they will sit for “just a few days.” If you are getting rid of your old appliance, please follow the instructions below to help prevent accidents.

Before You Throw Away Your Old Appliance:

Ŷ Take off the door. Ŷ Leave the shelves in place so that children may not easily climb inside.

49-60809 Rev. 2

SUFFOCATION AND ENTRAPMENT HAZARD

ENGLISH

BEVERAGE CENTER SAFETY

PROPER DISPOSAL OF YOUR OLD APPLIANCE (Cont.)

Refrigerant and Foam Disposal:

Dispose of beverage center in accordance with Federal and Local Regulations. Flammable refrigerant and insulation material used require special disposal procedures. Contact your local authorities for the environmentally safe disposal of your beverage center.

READ AND SAVE THESE INSTRUCTIONS

PARTS AND FEATURES

A. Full-width Glass Shelves (4) B. Temperature Control C. See-through Glass Door

D. Recessed Door Handle E. Lock with Key F. Leveling Legs (2)

49-60809 Rev. 2

INSTALLATION REQUIREMENTS

LOCATION REQUIREMENTS

WARNING

FIRE OR EXPLOSION HAZARD Keep flammable materials and vapors away from appliance. Failure to do so can result in death, explosion or fire.

Recommended Clearances:

Top

2" (5 cm)

ENGLISH

Back

2" (5 cm)

Sides

(12.7 cm)

IMPORTANT: This beverage center is designed for freestanding installation only. It should not be recessed or built-in an enclosed cabinet. To ensure your beverage center works at optimum efficiency, you should install it in a location where there is proper air circulation, and electrical connections.

LOCATION REQUIREMENTS

• Do not install the beverage center where the temperature will go below 55°F (13°C) because it will not run often enough to maintain proper temperatures.

• Do not install the beverage center where the temperature will go above 110°F (43°C) because it will not perform properly.

• Install it on a floor strong enough to support it fully loaded.

• Do not install the beverage center in a location exposed to water (rain, etc.) or direct sunlight.

49-60809 Rev. 2

ENGLISH

INSTALLATION REQUIREMENTS

CONNECTING ELECTRICITY

WARNING

Plug into a grounded 3-prong outlet. Do not remove the ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock.

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.

Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.

The beverage center should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate.

A 115 Volt AC, 60 Hz, 15- or 20-amp fused, grounded electrical supply is required. This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.

Never unplug your beverage center by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet.

Immediately discontinue use of a damaged supply cord. If the supply cord is damaged, it must be replaced by a qualified service professional with an authorized service part from the manufacturer.

When moving the beverage center away from the wall, be careful not to roll over or damage the power cord.

ELECTRICAL SHOCK HAZARD

49-60809 Rev. 2

INSTALLATION INSTRUCTIONS

STEP 1 - UNPACK BEVERAGE CENTER

WARNING

FIRE OR EXPLOSION HAZARD Do not puncture refrigerant tubing. Follow handling instructions carefully. Flammable refrigerant used. Failure to do so can result in death, explosion or fire.

IMPORTANT: Handle with care when moving beverage center to avoid

either damaging the refrigerant tubing or increasing the risk of a leak. IMPORTANT: When moving the beverage center, never tilt it more than

a 45° angle. This could damage the compressor and the sealed system. If the beverage center has been placed in a horizontal position for any period of time, wait 4 hours before plugging in the beverage center to allow the refrigerant to settle.

ENGLISH

REMOVE PACKAGING

Ŷ Remove tape and glue residue from surfaces before turning on the

beverage center. Rub a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

NOTE: Do not use sharp instruments, rubbing alcohol, flammable fluids,

or abrasive cleaners to remove tape or glue. These products can damage the surface of your beverage center. For more information, see “Beverage Center Safety.”

Ŷ Dispose of/recycle all packaging materials.

CLEAN BEFORE USING

After you remove all of the packaging materials, clean the inside of the beverage center before using it. See the cleaning instructions in “Beverage Center Care.”

49-60809 Rev. 2

ENGLISH

INSTALLATION REQUIREMENTS

STEP 2 - DOOR REVERSING (Optional)

WARNING

Follow all steps when reversing the door swing. Failure

to follow these instructions, leaving off parts, or overtightening screws, can lead to the door falling off and result in injury and property damage.

The door hinges are factory installed on the right-hand side. If you want the doors to open from the opposite direction, you can reverse the door swing.

TOOLS NEEDED

• 5/16” Hex-head Wrench

• 3 mm Hex Key

• Putty Knife

IMPORTANT:

• Before you begin, unplug the beverage center, or disconnect power.

• The door is heavy and fragile and the door front is glass. To avoid door glass breakage, use both hands and grasp only the sides of the door to remove.

1. Remove all items from inside the beverage center.

2. Using two or more people, gently lay the beverage center on its back.

Keep the machine standing over 4 hours before using if you lay the beverage center on its back.

3. Using a 5/16” hex-head wrench, remove the three hexagonal screws

fastening the bottom hinge to the cabinet, and set aside.

Bottom Hinge Screws

4. Remove the bottom hinge and the two washers. Set the washers aside.

49-60809 Rev. 2

INSTALLATION INSTRUCTIONS

STEP 2 - REVERSE DOOR (Optional) (Cont.)

5. Using a 3 mm hex key remove the hinge pin from the bottom hinge, and

then reinstall the hinge pin in the hole next to the hole from which it was removed. Replace the two washers.

Hinge Pin

Washers

6. Remove the screw from the bottom of the cabinet and move it to the

matching hole on the opposite side.

ENGLISH

Screw

7. Using the three hex-head screws removed earlier, reinstall the bottom

hinge on the opposite side.

Screws

49-60809 Rev. 2

ENGLISH

INSTALLATION INSTRUCTIONS

STEP 2 - REVERSE DOOR (Optional) (Cont.)

8. Using a putty knife, gently pry upward on

Hinge Cover

the back edge of the top hinge cover to remove.

9. Using a 5/16” hex-head wrench, remove

the two screws fastening the top hinge, and then remove the hinge.

10. Using the putty knife remove the hole plug

from the door and the two hole plugs from the cabinet, and then replace them in the holes remaining from removing the top hinge.

Top Hinge Screws

11. Reinstall the top hinge on the opposite

side.

12. Replace the top hinge cover.

Hole Plugs

13. Stand the beverage center upright, and check that the door is aligned

with the cabinet.

IMPORTANT: If the beverage center has been placed in a horizontal position for any period of time, wait 4 hours before plugging in the beverage center to allow the refrigerant to settle.

NOTE: If the top of the door is not aligned with the cabinet, loosen the top hinge screws, adjust door and re-tighten top hinge screws.

Top Hinge Screws

49-60809 Rev. 2

INSTALLATION INSTRUCTIONS

STEP 3 - LEVEL BEVERAGE CENTER

Your beverage center has two leveling legs located in the front, bottom corners. After placing the beverage center in its final position, level the beverage center.

NOTE: The beverage center door will close easier when leveling legs are extended.

Adjust the Leveling Legs:

Ŷ To Raise – Turn the leveling legs to the left. Ŷ To Lower – Turn the leveling legs to the right.

Raise Lower

STEP 4 - COMPLETE INSTALLATION

ENGLISH

WARNING

ELECTRICAL SHOCK HAZARD Plug into a grounded 3 prong outlet. Do not remove the ground prong from the power cord plug. Do not use an adapter. Do not use an extension cord. Failure to do so can result in death, fire or electrical shock.

Ŷ Plug into a grounded 3 prong outlet.

49-60809 Rev. 2

ENGLISH

BEVERAGE CENTER USE

TEMPERATURE CONTROL

The temperature control dial has three temperature settings and OFF. The MIN setting is the least cold and the MAX setting is the coldest.

IMPORTANT: Turning the control to OFF turns off cooling in the beverage center; it does NOT disconnect the beverage center from the power supply.

Set the temperature control to MED. Allow 24 hours to cool before making further temperature adjustments.

NOTE: The beverage center will automatically maintain the temperature level you select.

SHELVES

To accommodate your storage needs, there are four glass shelves.

CAUTION

when they are cold. Glass shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping or dropping.

Tempered glass is designed to shatter into many small pieces if it breaks.

To Remove or Replace a Shelf: Ŷ To Remove - Tilt the front of the shelf upward,

and then slowly slide it forward.

Ŷ To Replace - Align the shelf with the supports

and gently slide the shelf toward the rear.

Do not clean glass shelves or covers with warm water

KEY EJECT LOCK

The lock is spring loaded so the key cannot be left in the lock. To lock or unlock, press the key in while turning. If the key is lost, contact your dealer for a replacement or call 877.337.3639 for US customers. In Canada, call

877.470.9174. Always give the model and serial number of the beverage center when requesting a replacement key.

WARNING

prevent a child from being entrapped, keep the key out of reach of children and away from the freezer.

Key

49-60809 Rev. 2

BEVERAGE CENTER CARE

CLEANING

WARNING

EXPLOSION HAZARD Use nonflammable cleaner. Failure to do so can result in death, explosion or fire.

IMPORTANT: Do not use harsh chemicals, ammonia, chlorine bleach,

concentrated detergent, solvents, abrasives or metal scouring pads to clean your product inside or out. They can damage and/or discolor the finish.

WARNING

ELECTRICAL SHOCK HAZARD Unplug your appliance or disconnect power before cleaning. Failure to do so can result in death, electric shock or personal injury.

ENGLISH

General

1. Unplug or disconnect power.

2. Wash interior surfaces, accessories, and outer frame with a solution of warm water mixed with 3 - 4 tablespoons of baking soda.

NOTE: Before using cleaning products, always read and follow manufacturer’s instructions and warnings to avoid personal injury or product damage. Before cleaning glass shelves or covers, read SHELVES section for instructions.

3. Rinse with clean, warm water.

4. Dry thoroughly with a soft cloth.

5. Plug in or reconnect power.

Door Gaskets

Gaskets must be kept clean and pliable to ensure a proper seal. Ŷ Clean door gaskets every 3 months with solution of baking soda and

warm water.

Ŷ Petroleum jelly applied lightly to the hinge-side gasket will keep the

gasket pliable and ensure a good seal.

49-60809 Rev. 2

ENGLISH

BEVERAGE CENTER CARE

DEFROSTING

DANGER

FIRE OR EXPLOSION HAZARD Flammable refrigerant used. Do not puncture refrigerant tubing. Failure to do so can result in death, explosion or fire.

For most efficient operation and minimum energy consumption, defrost whenever the frost becomes 1/8” (3.2 mm) thick.

IMPORTANT:

Ŷ Do not use mechanical devices to defrost. Under normal operating conditions, the beverage center is designed to self

defrost during periods when the cooling system cycles off. Under conditions of extreme heat and humidity, and/or prolonged or

frequent door openings, you may notice frost build up on the cold plate on the interior rear wall. This frost can be removed through a manual defrost.

To manually defrost:

1. Turn the temperature control dial to OFF.

2. After the frost has been cleared, move the temperature control dial back to its original position.

WARNING

49-60809 Rev. 2

BEVERAGE CENTER CARE

VACATION AND MOVING

Vacation

If you will be away for an extended period of time and do not want to leave the appliance on while you are gone, prepare it for your absence.

1. Remove all items.

2. Turn the temperature control to the OFF position.

3. Unplug or disconnect power.

4. Clean the interior. See “Cleaning.”

5. Clean lid/door gaskets. See “Cleaning.”

6. Prop doors open, so air can circulate inside.

Moving

If you are moving your beverage center to a new home, prepare the appliance for the move.

WARNING

FIRE OR EXPLOSION HAZARD Do not puncture refrigerant tubing. Follow handling instructions carefully. Flammable refrigerant used. Failure to do so can result in death, explosion or fire.

ENGLISH

IMPORTANT:

Ŷ Handle with care when moving to avoid either damaging the refrigerant

tubing or increasing the risk of a leak.

Ŷ When moving the beverage center, never tilt it more than a 45° angle. If

you do need to tilt it more than 45°or lay the beverage center on its back, keep it standing over 4 hours before using.

1. Complete vacation preparation steps 1 through 5. See “Vacation.”

2. Take out all removable parts, wrap them well, and tape them together so they don’t shift and rattle during the move.

3. Tape the lid/door closed and tape the power cord to the back of the beverage center.

49-60809 Rev. 2

ENGLISH

BEVERAGE CENTER CARE

REINSTALLING/USING BEVERAGE CENTER AGAIN

IMPORTANT: If the beverage center has been placed in a horizontal or tilted

position for any period of time, wait 4 hours before plugging in the beverage center to allow the refrigerant to settle.

1. Clean beverage center. See Cleaning.

2. Place beverage center in desired location and level. See Installation

Instructions.

WARNING

3. Plug into a grounded 3 prong outlet.

49-60809 Rev. 2

TROUBLESHOOTING

First try the solutions suggested here to possibly avoid the cost of a service call.

PROBLEM POSSIBLE CAUSE(S) SOLUTION

Beverage center does not run.

Compressor runs too frequently

Beverage center is unplugged.

The circuit breaker is

чхмууиз¦чшхсизтģтхчли

fuse is blown. The temperature control is in

the OFF position. The compressor has cycled

òģ

The room temperature is hot and/or humid.

Beverage center door is ajar. Close the door completely The door gasket is not

sealing properly. Frequent or prolonged door

openings.

Plug beverage center into a grounded 3 prong outlet.

Reset/Turn on circuit breaker or replace fuse.

Turn the temperature control to a setting between Min and Max.

Wait 30 to 40 minutes to see whether the compressor will start.

This is normal to maintain constant temperature during high temperature, humid days.

Clean the door gasket. See Cleaning.

Limit door openings to maintain the internal temperature.

ENGLISH

Door does not close properly

Beverage center is too warm

Beverage center is too cold

49-60809 Rev. 2

Door is blocked open. Rearrange or remove items

Beverage center is not level or door is not aligned.

Door is blocked open. Rearrange or remove items

The door is opened frequently.

A large amount of beverages was recently added.

The door is not sealing properly.

The control is not set to a cold enough temperature.

The control is set to a too cold setting.

that are keeping the door from closing completely.

Level beverage center or align the door.

that are keeping the door from closing completely.

Limit door openings.

Allow time for recently added beverages to cool.

Clean the door gasket. See Cleaning.

Adjust the temperature control to a colder setting.

Adjust the temperature to a less cold setting.

ENGLISH

TROUBLESHOOTING

First try the solutions suggested here to possibly avoid the cost of a service call.

PROBLEM POSSIBLE CAUSE(S) SOLUTION

Beverage center has an odor.

Gurgling sound Refrigerant circulating

Clicking The temperature control

Popping or cracking sound when compressor comes on

The beverage center needs cleaning.

through the cooling coils.

жьжпмсктсдсзтģ

Beverage center is not level.

The beverage center is touching a wall.

Clean beverage center. See Cleaning.

This sound is normal.

Level the beverage center.

ЬииХищипмскТйчлиĥттхмц

uneven, you may need to place metal or wood shims underpart of the beverage center.

Move the beverage center away from the wall and relevel, if necessary.

49-60809 Rev. 2

NOTES

ENGLISH

49-60809 Rev. 2

+ 47 hidden pages