Haier HDY-E60 User Manual

Extra Dry

100min

INNOVATIVE DESIGN

HDY-E60

number of the tumble dryer.

1 Read all instructions before using this dryer.
2 The interior of the dryer should be cleaned periodically by qualified service

personnel. An excessive amount of lint build up in the interior of the dryer could
result in inefficient drying and pose a possible fire hazard.

3 The appliance must not be installed behind a lockable door, a sliding door or a door with

a hinge on the opposite side to that of the tumble dryer in such a way that a full opening

of the tumble dryer is restricted.

4 Attention - rear panel can be hot.
5 The tumble dryer should not be used if industrial chemicals have been used to

6 The dryer must only be used for its intended purpose.
7 Clean lint screen before or after each load.
8 This appliance is not intended for use by people (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the

appliance by a person responsible for their safety. Young children should be

supervised to ensure that they do not play with the appliance.
9 Do not operate the dryer if any parts are missing or broken.
10 To avoid fire hazard or electrical shock do not use an adaptor plug or extension
cord or remove grounding prong from electrical power cord. Failure to follow this
warning can cause serious injury, fire or death.
11 To avoid fire hazard or electrical shock do not reach into the drum while the drum is

12 Do not attempt to modify or repair the controls.
13 The final part of a tumble dryer cycle occurs without heat (cool down cycle) to cool
items to a temperature that ensures that they will not be damaged. Never stop a
tumble dryer before the end of the drying cycle unless all items are quickly removed
and spread out so that the heat is dissipated.
14 Do not dry items that have been previously cleaned in, washed in, soaked in, or
spotted with substances such as cooking oil, acetone, alcohol, petrol, kerosene, spot
removers, turpentine,waxes and wax removers, etc. Do not store or use these items
on or in the vicinity of the dryer. Do not place items exposed to cooking oils in your
dryer. Items contaminated with cooking oils may contribute to a chemical reaction that
could cause a load to catch fire. Oil-affected items can ignite spontaneously, especially
when exposed to heat sources such as in a tumble dryer. The items become warm,
causing an oxidation reaction in the oil. Oxidation creates heat. If the heat cannot
escape, the items can become hot enough to catch fire. Piling, stacking or storing
oil-affected items can prevent heat from escaping and create a fire hazard. If it is
unavoidable that fabrics that contain vegetable or cooking oil or have been
contaminated by hair care products be placed in a tumble dryer they should first be
washed in hot water with extra detergent - this will reduce, but not eliminate, the
hazard.

moving. Wait until the dryer has stopped completely before reaching into the drum.

1

clean the dryer.

15 Do not dry unwashed items in the tumble dryer.

16 Fabric softeners, or similar products, should be used as specified by the fabric
softener instructions.
17 To prevent fire, do not use heat to dry items containing plastic, foam rubber or
similarly textured rubber-like materials, or items containing feathers or down. Items
such as foam rubber (latex foam), shower caps, waterproof textiles, rubber backed
articles and clothes or pillows fitted with foam rubber pads should not be dried in the
tumble dryer.
18 This dryer must be properly installed in accordance with the installation instructions

before it is used.
19 Do not install or store this dryer where it will be exposed to water and /or the weather.
Keep surrounding areas free from the accumulation of lint, dust and dirt.
20 To prevent shock hazard and assure stability during operation, the dryer must be
installed and electrically grounded by a qualified service person in accordance with

local codes.
21 Do not sit on top of the dryer.
22 If the power cord is damaged, it must be replaced by the manufacturer, its service

agent or similarly qualified persons in order to avoid a hazard.
23 Always disconnect dryer from electrical supply before attempting any service.
Disconnect power cord by grasping the plug, not the cord.
24 Do not repair or replace any part of the dryer or attempt any servicing unless

specifically

25 Before the dryer is removed from service or discarded, remove the dryer door to

prevent accidental entrapment.

26 Remove all objects from pockets such as lighters and matches.

recommended in the user-maintenance instructions.

Caution, risk of fire - this is a safety symbol. Failure to follow the warnings
outlined in these user instructions can cause a fire hazard.

INSTALLATION INSTRUCTIONS

FREE STANDING
INVERTED WALL MOUNTING

STACKING INSTALLATION
CHANGE THE VENTING MODE

INSTALL THE FLEXIBLE HOSE

11

12

13

14

14

15

2

Extra Dry

100min

Control panel

Top panel

Program selector

Door

Lint filter

Power supply cord

Air intake grill

Door switch

Exhaust grill

Model number
and Serial number

Back plate

Outlet cover

Read all instructions before using this dryer.
This dryer has been designed for domestic use only.

SAVE THESE INSTRUCTIONS.

This diagram may be slightly different from the layout of the dryer you
have just purchased due to technical improvements.

3

Attention:

1.Before operation, clean off any dust and dirt inside the drum of the dryer with a damp

towel.

2.Clean off any debris on the lint filter and in the duct to increase the drying efficiency.

Turning on power

Before turning on the power of the dryer check whether the supply voltage is in

accordance with the value indicated on the name plate.

f

Preparation of laundry load

- The dryer can only dry laundry which has been spun dry. Do not put in laundry which

is still dripping wet or has excess water.

- Make sure all pockets are empty before placing laundry in the dryer.

- Pull up zippers, mend loosened fasteners and tie up ribbons to prevent the

laundry from being entangled. If necessary, put small items in a laundry bag.

- To achieve a better drying result ensure the clothes are separated before loading into the
dryer.

Load to dry

Laundry type Cotton fabric Synthetic fabric
Maximum load 6 kg 3 kg

Warning：

1. Avoid drying wool, silk and other

delicate fabrics, they maybe
damaged.

2. Do not exceed the recommended

load limit. This could damage the
dryer as well as the laundry.

4

1. Power up

Insert the power plug into an appropriate power outlet that is properly installed and

grounded. Operating power supply: 220-240V~50Hz.

2. Laundry loading

Open the door and load the laundry into the drum of the dryer. For a more energy
efficient and better drying result, make sure the load has been spun dry. Try to
loosen the load when placing in the dryer.

Note: Check labels on clothing before placing them in the dryer. Some articles are not

suitable for machine dry. High temperature may damage the fabric.

May be tumble dry .

Do not tumble dry .

Normal dry .

Air dry, only .

3.Setting drying program

Turn the program knob to set your desired drying program.

4.Delay setting.

You may choose to start the dryer after a preset time.
The delay range is between 0.5 and 24 hours.

5. Program operation

After a program is set, gently touch the “START/PAUSE” button to start the program.
Drum reversal: The dryer is designed to rotate in each direction, clockwise and
anti-clockwise in a certain period to minimize tangling and ensure clothes dry
efficiently.

6. Program completion

After the program is complete, the dryer will stop tumbling and the display screen will
display “End”. Open the door and remove the laundry.

If the laundry is not removed, the dryer will automatically commence an "anti-crease"

protection cycle to keep your laundry from settling in one position and creasing. This

cycle will last an hour unless stopped. The dryer will run with cool air at set intervals.

To stop the anti-crease cycle press the start/pause button or open the door, empty
the dryer and turn off as shown below.

7. Turning off the dryer

Turn the program knob to the “OFF” position and turn the power off at the wall.

Note: Clean the filter after each load.

5

Extra Dry

100min

A - Program control knob

A DE

B

F

C

F

B - Delay button

You may choose to start the dryer after a preset time. The delay range is between

0.5 and 24 hours. Gently touch the delay button before a program starts, each touch
will add one hour. When in excess of 24 hours, the remaining time will be re-displayed.
After a delay time is set, touch the Start/P ause button to start the delay operation
and the indicator light will flash.

C - LED screen

This screen displays the remaining time for a program and the delay time.

D - Start/Pause button

After turning on the power, select the drying program you desire.

Gently touch Start/Pause button to start the dryer. To Pause a program gently touch
this button during the operation of the dryer. The display screen will flash and the
machine will be halted.Press the Start/Pause button again and the program will
continue to operate.

E - Program setting

Heat Dry

Extra dry*

Sensor Program

Normal**

100 min 100 minute timed drying cycle, choose the program
according to the type and weight of the fabric.

Timed Program

The dryer will automatically switch off the heater at the end of every heat drying cycle
and start a cool down phase. This is important as it removes the stored heat from the
laundry and helps prevent creasing.

Air dry

*) AS/NZS 2442.2 test program setting.
**) EN61121 test program setting.

F - Indicator light

60 min 60 minute timed cool air cycle, no heat applied.

30 min 30 minute timed cool air cycle, no heat applied.

60 min 60 minute timed drying cycle, choose the program
according to the type and weight of the fabric.

30 min 30 minute timed drying cycle, choose the program
according to the type and weight of the fabric.

The drying time will depend on the type of fabric.
The maximum time is 4 hours. Choose the program
according to the type of fabric.

6

WARNING! Unplug the power cord prior to any cleaning

Cleaning the surface
Wipe off any dust or dirt.

Note: Do not use excessive water,. a damp cloth is fine.

Do not use solvent.
Do not use spray cleaners when cleaning the interior.
Do not use harsh or abrasive cleaners.

Cleaning the filter screen
To ensure good ventilation during drying, the filter screen must be cleaned before
or after each use.

1. Remove the filter
Gently pull out the filter screen towards yourself.

2.Cleaning the filter
Remove the lint with a soft brush or vacuum
cleaner. Be careful not to damage the filters.
Remove any remaining lint from the lint screen
on the door.

3. Re-installing the filter
After cleaning filters, put the screen back in place.

Note: Never operate your dryer without the lint filter.

7

INSTALLATION INSTRUCTIONS

Unpacking your dryer

Dimensions
a=830 mm
b=600 mm
c=560 mm
Weight=30 kg

Remove the transport packaging (fig.1)
Remove the tape on the door (fig.2), the wall mounting kit and the inverted panel
film attached to the inside of the drum (fig.3) before starting the dryer.

fig.1

fig.2

fig.3

Packing accessories
Check list of the accessories and materials provided with the machine:

Name Quantity
User manual 1
Wall mounting kit 1
Inverted panel film 1
Flexible hose 1
Flexible hose clip 1
Hose connector 1

Stacking kit 1

To ensure the dryer operates normally, attention must be paid to the
following:

1. The rear of the dryer must not have any restriction to the intake of fresh
air.

2. Check the dryer for any damage. If any damage is found do not operate
and contact your supplier or Authorised Service Centre.

3.The dryer must be kept away from flammable substances.

4.The surrounding environment must be dry and ventilated.

5. For best results,the ambient temperature should be between 10
and 35 .

8

Extra Dry

100min

INSTALLATION INSTRUCTIONS

Extra Dry

100min

Free standing

The dryer stands on the floor and can easily be moved into position. Ensure
that it is placed on a level floor. Also ensure there is at least 50 mm air
clearance between the back of the dryer and the wall to allow fresh air flow
for efficient operation.

Attention:
Please don’t put a heavy
load on the dryer’s top panel,
such as a basket full of
wet laundry

Inverted wall mounting

The dryer can be mounted on the wall in the inverted position only by following
these instructions.
Invert the dryer so that the control panel is at the bottom (see figure 4) this
allows easier access to the controls.

1. Determine the location of the dryer on the wall and mark the bracket
position.

A minimum 50 mm is needed between the top of the dryer and the ceiling
for ease of installation;
If mounting above a washing machine, allow sufficient room to open the lid
of the washer.

Tools required

For plaster/ Drill & 3mm Bit

Wooden wall Philips head screwdriver

Wall mounting kit includes

Plastic spacers 2
Wall hanging brackets 2

Hanging hook 2

Description

Wood screws, 12gx50mm 4

Screws for hanging hooks 6

and plastic spacers.

1

1

Minimum lid

clearance

9

INSTALLATION INSTRUCTIONS

2.Fix the wall hanging brackets to the wall securely (eg. into the stud).

If the studs are too far apart, fit a timber slat to the studs then mount the
brackets onto the slat. The distance between each is 553 mm as per
diagram (Fig.1).

Fig.1

553 mm

Wood screw

3. Install the hooks to the dryer, in the inverted position.
Remove the 2 screws and 2 plastic plugs as indicated in Fig.2.

Fig.2

2 screws

2 plastic plugs

4. Align the hooks as shown in fig.3 and refit screws tightly. Install the
spacers provided in Fig.3.

Fig.3

2 hooks

3 screws

2 spacers

10

INSTALLATION INSTRUCTIONS

5. With assistance, mount dryer on wall brackets. See Fig.4.

Fig.4

6. A second control panel with inverted symbols is supplied. Peel the
release paper from the back of inverted film then place new control
panel film on the surface so that the writing is the correct way around.

7. Press the Start/Pause button and hold it in the pressed position, and at
the same time, turn the program dial knob from the OFF position to any
other program, until the inversion is displayed.

Caution：

Plug must be accessble after installation.

Stacking installation

You can use a stacking kit (included as an accessory) if you want to mount your dryer
on the top of a Haier front load washing machine, ensure the washer is the same
width as the dryer.

1. Remove 4 screws among screws on the bottom panel (see fig.1), and install the
stacking kit on the bottom panel (see fig.2).

Fig.1

4 Screws

Fig.2

11

stacking kit

INSTALLATION INSTRUCTIONS

Extra Dry

100min

2. Install the dryer with stacking kit on the top of the front load washing
machine (Fig.3). Drill two holes on both sides of washer with 2.9mm
diameter drill. Detailed drill postion as shown on the stacking kit. Make
sure the included screws are used. Fix the stacking kit on the top
cover of washing machine, as shown on Fig.4.

Dryer

Stacking kit

Washer

Fig.3

Fig.4

Change the venting mode

There are three venting options:

Front venting

The exhaust grill has a range of positions, which allows you to select the optimum
exhaust air angle. Simply hold the grill and rotate it until you reach the desired position.

Note: If the dryer is mounted on the wall you must use the front venting option.

12

INSTALLATION INSTRUCTIONS

Extra Dry

100min

Rear venting

If you want to choose the rear venting mode, the exhaust grill at the front of the dryer
needs to be replaced with the outlet cover from the back panel of the dryer. Gently
open the grill, using a thin tool such as a key. Next, remove the cover from the
back panel and clip it into the grill space at the front panel. The exhaust grill is not
required when using a flexible hose.

INSTALL THE FLEXIBLE HOSE(

optional

Flexible hose)

Connect the narrow end of the
connector to the dryer duct pipe mouth
at the back of the dryer. Then connect
the flexible hose to the wide end of
the connector. Use the clip to
fasten connection point between the
flexible hose and connector (fasten clip
with a screwdriver). Extend the flexible
hose through the duct hole, make
sure the flexible hose is not twisted to
allow the air to be vented outside.

Flexible connector

Flexible hose

Outdoor

Flexible hose clip

Vent cap

Duct hole

(diameter ＞100mm)

Notes: If duct hole is not available at user's home, make sure the flexible hose
is vented through a window.
If the dryer is mounted on the wall in the inverted position, you can not use the

flexible hose.
The flexible hose should be angled to avoid water running back into the dryer.

Ensure a vent cap is fitted when vented outside.

Correct fixing mode:

Fig.1

Fig.2 Fig.3

13

The following must be confirmed before calling for service:

Problem Possible Cause

Is the dryer plugged in?
Is the power on?

The dryer does not start

The drying result is not
good

Is the door closed properly?
Has a drying program been set?
Has the Start/Pause button been pressed?

Was the correct drying program set?
Is the filter screen clean?
Did the amount of the loaded laundry exceed
the rated load?
Was the laundry spun dry before being loaded
into the dryer?
Did the laundry become twisted during drying?

Door switch

NTC

Display board

Control board

Thermostat

Capacitor

Heater

L

M

～

N

Motor

14

Thermal cut-out

ITEM

TYPE

HDY-E60

Power supply

Maximum operating current (A)

Rated load (kg)

Drying program

Maximum power (W)

Dimensions (HxDxW) mm

Weight (kg)

Waterproof degree

（220-240)V~ · 50Hz

10

6

7

2100

830x560x600

30

IPX4

15

0180500432