Haier HDW700BI User Manual

Domestic Dishwasher
HDW700BI

GB

Code: 0120504940

Safety Is a Good Habit to Get Into

NOTICE

Carefully read the instructions contained in this manual, as they
provide important information which is essential to safe and
proper installation, use and maintenance of the appliance.

This appliance complies with following EEC di­ rectives:

- 73/23/EEC of 19/02/73(Low Voltage) and subsequent modifi
cations;

- 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and
subsequent modifications.

- Carefully dispose of the packing material.

- After removing the packing, check to make sure that the appli­ ance is not damaged. If in doubt, contact a qualified professional.

- The dishwasher must only be used by adults for the washing of
household dishes and cooking utensils.

- Fundamental rules to follow when using the appliance:
* Never touch the dishwasher when barefoot or with wet hands
or feet;
* We discourage the use of extension cords and multiple sock­ ets;
* During installation, the power supply cord must not be exces­ sively or dangerously bent or flattened;
* If the appliance is not operating properly or maintenance must
be performed, disconnect the appliance from the power supply.

- Keep detergents out of the reach of children, who must also be
kept away from the dishwasher when it is open.

GB

- This appliance cannot be installed outdoors, not even if the
area in which it is installed is covered by a roof; it is also very
dangerous to leave it exposed to the rain and elements.

- Do not touch the heating element during or after a wash cycle.

- Do not lean or sit on the door when it is open, as this could
overturn the dishwasher.

- If the appliance malfunctions, turn off water supply to the appli­ ance and disconnect the plug from the wall socket. Then, con­ sult the section entitled, "Troubleshooting." If you cannot re­ solve the problem, contact a service centre.

- Only specialised personnel are authorised to make repairs.

- Appliances which are no longer being used must be made inop­ erable by cutting the power supply cord and removing the door
lock.

Notice:

The appliance is not instruct for use of young children of
infirm persons without supervision.
Young children should be supervised to ensure that they do
not play with the appliance.
If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified per­son in order to avoid a hazard.

Close-up View (Interior)

Upper Rack

A

Rack Height Adjustor

B

Top Spray Arm

C

Bottom Spray Arm

E

Washing Filter

F

Detergent and Rinse Aid Dispenser

G

GB

Close-up View (control panel)

G

ON-OFF Button

A

ON-OFF Light

B

Delay select button

C

Delay indicator light

D

"HALF LOAD" Button

E

F
G
H
I
J

BEHJ

FI

D

"HALF LOAD" indicator light
Low rinse aid indicator light
Heat indicator light
Cycle select button
Cycle indicator light

C

A

Lower Rack

D

Technical characteristics

Width
Depth
Height
Capacity
Mains water pressure
Power voltage
Total absorber power

H

Third Sprayer

60 cm

58 cm
82 cm

12 standard place settings

0.03-0.6MPa

220-240V~ 50Hz

2150W

.1.

.2.

Detergent and Rinse Aid







GB

Loading the Dishwasher

GB

Detergent

Detergent specifically intended for use with dishwashers must
be used. The dispenser must be refilled before the start of each
wash cycle following the instructions provided in the "Wash Cycle
Table." The detergent dispenser is located on the inside panel
the door.

Loading the detergent

To open the "A" cover on the dispenser, press the "B" button.
The detergent for the wash cycle should be poured into the "C"
compartment.
After the detergent has been placed in the dispenser, close the
cover and press down until it clicks in place.

C

A

B

Notice: To facilitate closing the cover, remove any ex­cess detergent on the edges of the dispenser.
Dishwasher detergents are strongly alkaline. They can
be extremely dangerous if swallowed. Avoid contact
with the skin and eyes and keep children away from the
dishwasher when the door is open. Check that the de­tergent receptacle is empty after completion of the wash
cycle.

Rinse Aid

This product makes dishes sparkle and helps them to dry with­out spotting. The dispenser is located on the inside panel of the
door and should be filled after every 80 wash cycles (or when
the "low rinse aid" indicator light comes on for those models
with this feature).

Loading the Rinse Aid

Regardless of the type of detergent dispenser installed on your
appliance, you must proceed as indicated below when loading
the rinse aid.
To open the dispenser, turn the "C" cap in an anti-clockwise
direction and then pour in the rinse aid, making sure not to overfill.
The amount of rinse aid used for each cycle can be regulated by
turning the "F" dose adjustor, located beneath the "C" cap, with
a screwdriver. There are 6 different settings; the normal dosage
setting is 3.

Important

Proper dosage of the rinse aid improves drying.
If drops of water remain on the dishes or spotting occurs,
the dosage adjustor should be turned to a higher setting.
If the dishes have white streaks, turn the dosage adjustor
to a lower setting.

C

F

C

Before placing the dishes in the dishwasher, remove larger food
particles to prevent the filter from becoming clogged, which re­sults in reduced performance.
If the pots and pans have baked-on food that is extremely hard to
remove, we recommend that they are soaked before washed. This
will eliminate the need for extra wash cycles.
Pull out the rack to load the dishwasher.

How to use the lower rack

We recommend that you place the most difficult to clean items on
the bottom rack: pots, pans, lids, serving dishes and bowls, as
shown in the figure to the right.
It is preferable to place serving dishes and lids on the sides of the
racks in order to avoid blocking the rotation of the top spray arm.

- Pots, serving bowls, etc. must always be placed face down.

- Deep pots should be slanted to allow the water to flow out.

- The silverware basket can be doubled (see fig.A) so that only
one section may be used when the silverware load is light. This
also makes space for additional pots and pans and it can also be
placed in the upper rack.

- Silverware should be placed in the silverware basket with the
handles at the bottom; if the rack has side baskets, the spoons
should be located individually into the appropriate slots. Espe­ cially long utensils should be placed in the horizontal position at
the front of the upper rack.

How to use the upper rack

The upper rack is designed to hold more delicate and lighter
dishware, such as glasses, cups and saucers, plates, small bowls
and shallow pans (as long as they are not too dirty).

- Position the dishes and cookware so that they do not get moved
by the spray of water.
The upper rack can be adjusted for height by using the knobs lo­cated on the sides of the rack itself (see fig.B).

Shelf

Lean tall glasses and those with long stems against the shelf-not
against other items to be washed (see fig.C).
Long items, serving cutlery, salad, servers or knives should be
placed on the shelf so that they do not obstruct the rotation of the
spray arms. The shelf can be folded back when not required for
use.

Lower Rack Top Rack

Load for 12 Standard Settings

3

fig.C

1

2

4

fig.Bfig.A

fig.D

.3.

.4.

Starting the Appliance

GB

Wash Cycle Table

GB

Starting a wash cycle

After having completed all of the installation steps in the preced­ing paragraphs, turn on the water to the unit, partially open the
door of the dishwasher, and press the ON-OFF button "A" lo­cated on the control panel. The "B" indicator light will come on.
At this point, the appliance is on and ready to be programmed.







Setting and Starting a wash Cycle

Choose the desired cycle by pressing the cycle selection button
"P". Each time it is pressed, one of the cycle indicator lights "J"
will come on in succession.
Choose the wash cycle you feel is most appropriate for the type
of dishes that need washing (consult the wash cycle table con­tained in this manual, especially when first using the appliance).
Close the door and after a few seconds, the wash cycle has be­gun and cannot be modified. If necessary, read the paragraph
entitled, "Cancelling or modifying a cycle while underway. "The
end of the cycle will be signalled by a double acoustic sound, and
the indicator light "J" will begin to blink.

Cancelling or modifying a cycle while underway...

Premise: A cycle that is underway can only be modified if it has
only been running for a short time.

Otherwise, the detergent may have already been used, and the
appliance may have already drained the wash water. If this is the
case, the detergent dispenser must be refilled (see the paragraph
entitled, "Loading the Detergent").

At the end of the wash cycle...

The end of the cycle will be indicated by a double acoustical
signal and the blinking of the "J" indicator light. Open the door,
turn off the appliance using the ON-OFF switch and turn off the
water supply to the unit. Wait a few minutes before removing the
dishes so as to avoid handling them while still hot (when they
are more susceptible to breakage) and to get better drying results.

Setting The Start Delay Time

Open the door of the dishwasher partially. If the "C" button is
pressed (see, Close-up View" Control Panel"). The start time for
the wash cycle can be delayed for 2,4,6,8,10 or 12 hours.
Each time the button is pressed, the "D" light will come on indi­cating the length of the delay.
After selecting the delay time, the wash cycle can be set, as
explained in "Setting and starting a wash cycle..." There will be a
short acoustic signal, and at this point the delay period will begin
to count down. During this period the delay indicator light (D) will
blink. At the end of the delay time, the indicator will stop blinking
and the cycle will start.

NOTE:

During the delay period, none of the settings can be modified. If
the ON-OFF button "A" located on the contro panel, the door is
opened during the delay period, the clock will stop the countdown.
It will start again when the door has been closed.

Cycle

Heavy Duty

Normal Wash

Light Wash

Glassware

Cycle
Selection
Information

Very dirty dishes,
pots and pans. (Not
to be used with deli­cate items)

Normal dirty dishes,
pots and pans. Stan­dard daily cycle.

Normal dirty dishes,
pots and pans without
dried on residue.

Economic, fast cycle to
be used for items which
are sensitive to higher.
Run immediately after
dishes are used.

Description of
Cycle

Pre-wash with hot water.
Extended wash at 70K
Rinse with cold water.
Rinse with hot waterK
Drying.

Pre-wash with cold water.
Extended wash at 50.

Rinse with cold water.
Rinse with hot water.
Drying.

Pre-wash with cold water.
Extended wash at 50K
Rinse with cold water.
Rinse with hot waterK
Drying.

Wash at 45.
Rinse with warm water.
Hot rinse.
Drying.

Detergent Rinse Aid

30g

5+25g

30g

15g



ERF





To change the cycle currently underway, open the door, the ON­OFF bution "A". Follow the instructions contained in the para­graph entitled "Starting a wash cycle...","Setting and starting a
wash cycle".

To set a new wash cycle, follow the instructions contained in the
paragraph entitled, "Setting and Starting a Wash Cycle".

If you forget to load some of the dishes...

The wash cycle can be interrupted by opening the door carefully
(in order to avoid being sprayed by hot water). When the door is
closed again, the cycle will automatically restart at the point where
it left off.

Wash Cycle Adjustment Buttons

1/2 Load Button

This button (see" Close-up View-Control Panel", letter "E") makes
it possible to wash dishes using only the upper rack if there are
not enough dishes for a full load, This will allow you to save on
water and electrical energy.

.5.

Rapid Wash

Soak

Heat wash

Economic, fast cycle to
be used to on not very
dirty dishes right after
they are used. No dry­ing cycle.

Pre-wash of dishes,
pots and pans while
waiting for the load to
be completed after the
subsequent meal.

The cycle of heat wash­ing and dry tableware.

Short wash at 40.
Cold rinse.

Short cold wash to prevent
food residue from drying on
the dishes K

Heat washing.

.6.

15g



Energy Saving Tips

GB

Troubleshooting

GB

-It is important to try and run the dishwasher when it is fully
loaded in order to save on energy. In order to prevent odors
from forming and food from caking onto the dishes, you can run
the hold cycle.

-Choose the right wash cycle: the choice of cycle depends on
the type of dishware, cookware and utensils being washed and
how dirty they are.

How to keep Your Dishwasher in Shape

After Every Wash

After every wash, turn off the water supply to the appliance and
leave the door slightly ajar so that moisture and odors are not
trapped inside.

Remove the plug

Before cleaning or performing maintenance, always remove the
plug from the socket. Do not run risks.

No solvents or Abrasive Cleaning Products

To clean the exterior and rubber parts of the dishwasher, do not
use solvents or abrasive cleaning products. Rather, use only a
cloth and warm soapy water.
To remove spots or stains from the surface of the interior, use a
cloth dampened with water and white vinegar, or cleaning prod­uct made specifically for dishwashers.

Cleaning and Special Maintenance

Filter Assembly

For best performance and results, the filter assembly must be
cleaned frequently.
The filter efficiently removes food residue from the wash water,
allowing it to be recirculated during the cycle. For this reason, it
is a good idea to remove the larger food particles trapped in the
filter after each wash cycle by rinsing the "A" semi-circular filter
and cup under running water. To remove the filter assembly, pull
on the cup handle in the upward direction. The entire filter as­sembly (made up of the "A" semicircular filter and the "B" fine
filter) should be cleaned at least once a week.
To clean the filter and the fine filter, use a cleaning brush. Then,
reassemble the filter parts as shown in the figures below and
reinsert the entire assembly in the dishwasher, positioning in its
seat and pressing downward.

The dishwasher must never be
used without the filters. Improper
replacement of the filters may re­duce level of the appliance and
damage dishes and utensils.

-Use the right amount of detergent: if you use too much deter­gent, the result will not be cleaner dishes, but, rather, a greater
negative impact on the environment.

-There is no advantage in rinsing dishes, cookware and utensils
before placing them in the dishwasher.

When You Go on Holiday

When you go on holiday, it is recommended that you run a wash
cycle with the dishwasher empty and then remove the plug from
the socket, turn off the water supply and leave the door of the
appliance slightly ajar. This will help the seals last longer and
prevent odors from forming within the appliance.

Moving the Appliance

If the appliance must be moved, try to keep it in a vertical position.
If absolutely necessary, it can be positioned on its back.

Seals

One of the factors that cause odors to form in the dishwasher is
food that remains trapped in the seals. Periodic cleaning with a
damp sponge will prevent this from occurring.

Cleaning the Spray Arms

It may happen that food particle become encrusted on the spray
arms and block the holes. Check the spray arms periodically and
clean them when needed.

A

B

Cleaning the Water Inlet Filter

Periodically clean the water inlet filter (see figure) located on the
outlet of the water supply tap.
After turning off the water tap, unscrew the end of the water sup­ply hose, remove the filter and clean it carefully under running
water. Then, return the filter to its place and tighten the water
supply hose back into position.

It may occur that the dishwasher does not function or does not
function properly. Before calling for assistance, Iet us see what
can be done first: have you forgotten to press one of the buttons
or to perform an essential operation?

The Dishwasher Does Not Start

Have you checked whether:

- the plug is pushed into the socket correctly;

- the power is on in the house;

- the door is closed properly;

- the ON-OFF switch is on "ON";

- the water supply is turned on.

The Dishwasher Does Not Load Water

Have you checked whether:

- the water is turned on and the hose is connected properly;

- the water supply to the house is on and has sufficient pressure;

- the water supply hose is crimped or bent;

- the filter for the water supply hose is clogged.

The Dishes Are Not Clean

Have you checked whether:

- the water is turned on and the hose is connected properly;

- the water supply to the house is on and has sufficient pressure;

- the water supply hose is crimped or bent;

- the filter for the water supply hose is clogged.

The Dishwasher Does Not Drain

Have you checked whether:

- the drain hose is crimped or bent.

Lime Deposits or a White Film Form on the Dishes

Have you checked whether:

- the lid to the salt container is closed properly;

- the rinse aid dosage is correct.

Error Messages

The dishwasher is equipped with a safety system that is able to
detect operating problems and malfunctions. These malfunctions
are signalled by the rapid blinking of one of the program LEDs.
Only in the case where the indicator light for the soak cycle (see
table for cycles) blinks rapidly should you cancel the cycle as
described in the section entitled, "Changing a Cycle while Under­way." Then check to make sure that there is water in the mains
and that the tap is turned on. If the message continues, call for
technical assistance, indicating which message appeared.
If any of the other indicator lights begins to blink rapidly, turn off
the appliance and call for technical assistance, indicating which
light began to blink.

If, despite all these checks, the dishwasher still does not function
and/or the problem persists, contact the nearest authorised ser­vice centre and provide them with the following information:

- the nature of the problem;

- the model type number (Mod...) And the
serial number (S/N...), which are indicated on the plate located
on the side of the inner part of the door.

Never call on unauthorised technicians and refuse to
allow parts to be installed that are not original spare
parts.

.7.

.8.

Installation

Power switch

Wiring box

Door switch

Power indicator

switch

agent
missing

Rinsing

Overflow switch

Dispenser

Washing valve

Washing pump

Water level switch

Drain pump

Temperature limiter

Inlet valve

Temperature limiter

Heater

1

2(1)

220-240V ~ 50HZ

N

L

IG

3(1)

4(2)

F

IS

LS

1(2)

CnL1

43

287

65

1

4

CnP3

1

5
6

3

2

4

CnP1

6
5

8

7

11

CnP2
12

9

7

5

6

8

10

3
2
1

4

2

3

1

Temperature
Sensor

RELE’

1

3

1

2

L

D-ED

1/2

1

3

M

IAQS

2

ML

S

control panel

Relay

C

GB

Installation

Positioning the Appliance

Positioning the appliance in the desired location. The back should
rest against the wall behind it, and the sides, along the adjacent
cabinets or wall. The dishwasher is equipped with water supply
and drain hoses that can be positioned to the right or the left to
facilitate proper installation.

Levelling the Appliance

Once the appliance is positioned, adjust the feet (screwing them
in or out) to adjust the dishwasher, making it level. In any case,
the appliance should not be inclined more than 2˚. If the appli­ance is level, it will help ensure proper performance.

Cold Water Connection

Connect the cold water supply hose to a threaded 3/4 (gas)
connector, making sure that it is fastened tightly in place (see fig.1).
If the water pipes are new or have not been used for an extended
period of time, let the water run to make sure that the water is
clear and free of impurities. If this precaution is not taken, there
is a risk that the water inlet can get blocked and damage the
appliance.

Drain Hose Connection

Insert the drain hose into a drain pipe with a minimum diameter
of 4cm, Or let it run into the sink, making sure to avoid bending
or crimping it. Use the special plastic support that comes with
the appliance (see fig.2). The free end of the hose must be at a
height between 40 and 100 cm and must not be immersed in
water.

fig.2

Diagram

Hot Water Connection

The water supply to the appliance can also be connected to the
house's hot water line (centralised system, heating system), as
long as it does not exceed a temperature of 60
In this case, the wash cycle time will be shortened by about 15
minutes and the wash efficiency slightly reduced.
The connection must be made to the hot water line following the
same procedures as those for the connection to the cold water
line.



 .



fig.1

Attention:

The special plastic hose support must be solidly fastened to the
wall to prevent the drain hose from moving and allowing water to
spill outside the drain.
Use the new hose and the old hose should not be reused.

Electrical Connection

After making sure that the voltage and frequency values for the
current in the home correspond to those on the rating plate
(located on the stainless steel inner door of the appliance) and
that the electrical system is correct for the maximum voltage on
the rating plate, insert the plug into an electrical socket which is
earthed properly (the earthing of the appliance is a safety re­quirement mandated by law).
If the electrical socket to which the appliance must be connected
is not appropriate for the plug, replace the plug, rather than us­ing adaptors or the like as they could cause overheating and
burns.

Caution:

The dishwasher plug must be accessible even when the appli­ance is installed as a built-in unit so that maintenance can be
done safety.

.9.