User Manual
Dishwasher
HDW15V2*2 Models
AA
Thank you for purchasing a Haier product
Please read these instructions carefully before using this appliance. The
instructions contain important information which will help you get the
best out of the appliance and ensure safe and proper installation, use and
maintenance.
Keep this manual in a convenient place so you can always refer to it for
the safe and proper use of the appliance.
If you sell the appliance, give it away, or leave it behind when you move
house, make sure you also pass on this manual so that the new owner
can become familiar with the appliance and safety warnings.
Legend
General information and tips
Warning – Important Safety information
Environmental information
Disposal
Help protect the environment and human health. Put the packaging
in applicable containers to recycle it. Help to recycle waste of electrical and electronic appliances. Do not dispose appliances marked
with this symbol with the household waste. Return the product to
WARNING!
Risk of injury or suffocation!
Disconnect the appliance from the mains supply. Cut off the mains
cable and dispose of it. Remove the door catch to prevent children
and pets to get closed in the appliance.
1
Content
Safety ............................................................................................... 3
Product Description ....................................................................... 5
Control Panel ................................................................................. 6
Programmes ................................................................................... 8
..............................................................................
Daily Use ....................................................................................... 12
Care and Cleaning ........................................................................ 20
Troubleshooting .......................................................................... 22
Economic and Environmental Use ............................................. 25
Installation .................................................................................... 26
Technical Data ............................................................................. 29
Customer Service ........................................................................ 30
Standards Test ............................................................................. 31
9
2
Safety
Intended Use
The appliance is designed for domestic use inside the house. It is not
intended for commercial or industrial use. Do not use it for purposes other
than that for which it was designed.
may cause hazards and loss of warranty claims.
Standards and Directives
This product meets the requirements of all applicable EC directives with
the corresponding harmonised standards, which provide for CE marking.
Before Switching on the Appliance for the First Time
Do…
▶
make sure all packaging is removed and is kept out of children’s reach.
▶ make sure that the electrical information on the rating plate agrees
with the power supply. If it does not, contact an electrician.
▶ use a separate earthed socket for the power supply. The appliance
must be earthed.
▶ make sure the plug is easy accessible.
▶ make sure only the delivered electric cable and hose set are used.
▶ hold the plug and not the electric cable when unplugging the power
supply.
▶ make sure not to damage the electric cable and the plug. If damaged,
have it replaced by an electrician.
▶
leakage.
Do not…
install or use the appliance where the temperature is below 5 °C.
use multi-plug adapters and extension cables.
let persons, children included, with reduced physical sensory, reduced
mental functions or lack of experience and knowledge use the appli-
ance if not supervised by a person responsible for their safety.
products in, near, or on the appliance.
3
Safety
During Daily Use
Do…
▶ supervise children to prevent them playing with the appliance.
▶ put sharp pointed objects (e.g. knives) in a way that there is no
danger of injury.
Do not…
open the door while a programme operates. The appliance can
release hot steam.
keep the appliance door open without supervision to prevent trip-
ping and falling.
let children or pets come close to the appliance when the door is
open.
sit or place heavy items on the open door.
remove the dishes from the appliance until the programme is
completed. There can still be detergent on the dishes.
drink the water in the appliance. The water may be contaminated
with detergent residues.
cover any ventilation openings in the base by a carpet or similar
object.
use water spray or steam to clean the appliance.
let the children make the cleaning and user maintenance without
supervision.
WARNING:
Some dishwasher detergents are strongly alkaline.They can be extremely
dangerous if swallowed.Avoid contact with the skin and eyes and keep
children away from the dishwasher when the door is open.Check that
the detergent receptacle is empty after completion of the wash cycle.
4
Product Description
1.
Upper basket
Upper spray arm
2.
Lower spray arm
3.
Lower basket
4.
Cutlery basket
5.
Rating label
6.
Detergent dispenser
7.
Rinse aid dispenser
8.
Filters
9.
Knife rack
10.
Thermo dry
11.
Accessories
Check the accessories and literature in accordance with this list:
water inlet hose
5
U-support
User manual
Control Panel
HDW15V2*2 :
1
1.
ON / OFF button
PROGRAMME SELECT button
2.
Programme Indicators
3.
Status Indication
4.
Time & Info Display/Indicator Icon
5.
START DELAY button
6.
START / PAUSE button
7.
2
Time & Info display
►
Programme cycle time
►
Programme start delay time
►
Error codes and service information
5
4
33
6
7
like
► Remaining time in hours of a delayed programme starts, e.g.
► Remaining programme cycle time in hours + minutes, e.g.
While running it may vary due to local conditions and daily
working load.
6
Control Panel
Indicator Icon
Rinse aid
Water tap
Child Lock
Delay start
Status Indicators
Wash If the indicator lights up: the Dishwasher is washing.
Rinse
Dry
Option Indication
Delay start
Child Lock
If the indicator lights up
After adding Rinse Aid, press for 3 seconds
and the light goes out.
water.
Check section: “TROUBLESHOOTING”
If the indictor lights up:Child lock mode has been opened
If the indictor lights up:Delay start mode has been opened
If the indicator lights up: the Dishwasher is rinse washing.
If the indicator lights up: the Dishwasher is drying.
Rinse aid is empty!
:
You can delay the start of a programme in 1 hour steps up
to 24 hours. Check the according paragraph under “Daily
use”.
To activate or cancel Child lock , press and hold
until the Child lock indicator comes on or turn off.
7
Programmes
Light to heavy soil:
1)
Auto
Casseroles, sauces,
pasta, rice,
roasted or fried food
potatoes,
Heavy soil:
Heavy
Casseroles, sauces,
rice,
pasta,
roasted or fried food
potatoes,
Fresh soil:
2)
Light
Glass
Coffee, cake, milk,
salad,
sausages
Light soil:
Coffee, cake, milk,
sausages
salad,
cold drinks,
cold drinks,
Dishes to be stored
Rinse
3)
for a few days
before washing
Normal soil:
ECO
Soups, eggs, sauces,
pasta, rice,
roasted or fried food
potatoes,
Non-delicate:
Dinnerware,
pots and pans
Non-delicate:
Dinnerware,
pots and pans
Non-delicate:
Dinnerware,
cutlery,
glassware
Delicate:
Glassware,
cutlery
All:
Dinnerware,
glassware,
pots and pans
Non-delicate:
Dinnerware
glassware
cutlery,
cutlery,
dinnerware,
cutlery,
cutlery,
1) The appliance senses the type of soil and the quantity of items in the baskets. It automatically
adjusts the temperature and quantity of water, energy consumption and programme duration.
2)
With this programme you can wash a load with fresh soil. It gives good washing results in a
short time.
3)
Use this programme to quickly rinse the dishes. This prevents the remaining food to bond on
the dishes and bad odours to come out from the appliance. Do not use detergent with this
programme!
8
First Steps
Remove all packaging materials, keep them out of children’s reach and
dispose them in an environmentally friendly manner. There could be water
residue inside the appliance due to quality checks in the factory.
Perform the following steps:
1. Install the appliance.
Refer to section INSTALLATION.
2.
Only for use of Multitabs: Adjust the rinse aid setting.
Refer to section DIFFERENT SETTINGS FOR RINSE AID.
3.
Fill the rinse aid dispenser.
Refer to section HOW TO FILL THE RINSE AID DISPENSER.
Open the water tap.
4.
Start any wash programme (apart from Rinse programme）
5.
with detergent but no load to remove possible manufacturing residues.
Activate / De-Activate the Buzzer
An accoustic signal informs about the end of a programme. This signal
can be switched off.
Refer to section HOW TO ADJUST SETTINGS and select the -setting:
If the display shows the signal is switched off.
If the display shows
the signal is switched on.
9
Different Settings for Rinse Aid
Rinse aid is added during the last rinsing phase to dry the dishes without
streaks and stains.
Detergent (e.g. powder, tablets, ...)
requires separate rinse aid:
Factory default setting:
The rinse aid is added from the rinse aid dispenser only.
Detergent with multifunction (e.g. Multitabs)
combine detergent and rinse aid:
The rinse aid setting should be adjust to . Please use the setting
instructions in section HOW TO ADJUST SETTINGS and select the
-setting.
The rinse aid is added from the rinse aid dispenser in addition to the
multitabs rinse aid.
Setting cuts off the rinse aid dosage and the rinse aid indication.
The higher the value for the higher the dosage.
Usually the recommended setting performs well. In case of streaks,
stains, shimmer etc.; refer to section TROUBLESHOOTING.
. No settings are necessary.
CAUTION!
Only use rinse aid for dishwashers.
Other products can cause damage to the appliance!
1. Press the release button (B) to open
the lid.
2.
Fill the tank (A) up to the ‘max’ mark.
3.
Remove any spilled rinse aid with
an absorbent cloth. Overdosed or
spilled rinse aid may cause problems
creating foam
4.
Close the lid. Make sure that the
release button locks into position.
10
How to Adjust Settings
To adjust the Rinse Aid level
1. The appliance is switched on.
2. Press and hold
►The display shows the current Rinse Aid setting (the default is ).
and
a
bout 3 seconds until
:
Press
3.
in steps between
To exit the Rinse Aid menu, press and hold for 1 second.
4.
to change the Rinse Aid setting
(minimum dispense) and
(maximum dispense).
Activate / De-Activate the Buzzer
1. The appliance is switched on.
2. Press and hold
►The display shows the current Rinse Aid setting.
3.
Press to scroll to the buzzer menu.
The display will show (buzzer off) or (buzzer on).
4.
Press to toggle between
5.
and
for about 3 seconds until:
(buzzer off) or (buzzer on).
To exit ,press and hold 1 second. 6.
Child lock
This feature disables all the buttons on the dishwasher. If any other
buttons are pressed while Child lock is activated, the Child lock
indicator will flash for a few seconds.
1.To activate Child lock, press and hold for 3 seconds.
and
2.The display will remain on (if no programme has been started it will
continue to flash while the control panel is locked).
3.To cancel Child lock, press and hold for 3 seconds.
and
11
Daily Use
Please note that not all sales models comes with identical features and
options. So pictures of that chapter are sometimes different to your dishwasher model. Explanations try only to point out basic model variants.
1. Load the baskets.
2. Press the ON/OFF button
▶
If the rinse aid indicator is on, fill the rinse aid dispenser and
the rinse aid indicator; refer to section HOW TO RESET
reset
3.
4. Close the door.
5. Set the programme according to the type of load and how dirty the
6. Maybe select a start delay time.
7. Press the START / PAUSE button
8.
After programme end the appliance change to auto off. Unload the
THE RINSE AID IDNICATOR.
Add the detergent; refer to section DETERGENT.
dishes, cups and cutlery are.
baskets.
to activate the appliance.
to start the programme.
How to Reset Rinse Aid Indicator
The appliance is switched on.
The rinse aid indicator is on:
1.
Always completely fill the rinse aid before starting the next wash
cycle.
2. Press and hold the START/PAUSE button
indicators
light up. The Status Indicators light up.
until the Rinse Aid
12
Daily Use
Load the Baskets
With delicate glasses and porcelain make sure they are labelled
dishwasher-proof.
Do not put in the appliance items made of wood, horn, aluminium,
pewter and copper.
Do not put in the appliance items that can absorb water (sponges,
household cloths).
▶ Only use the appliance to wash items that are dishwasher-safe.
▶ Remove remaining food from the items.
▶ Soften burned food on the items before washing.
▶ Put hollow items (cups, glasses and pans) with the opening down.
▶ Put items with deep hollows in a slanted position.
▶ Mix spoons with other cutlery to prevent them to bond together.
▶ Make sure that cutlery and dishes do not bond together and there
is a gap between each item.
▶ Make sure that glasses do not touch other glasses.
▶ Put small items in the cutlery basket.
▶ Put light items in the upper basket. Make sure that the items do
not move.
▶ Make sure that the spray arms can move freely before you start a
programme.
If jingling noises are heard during a programme run: Check that the
Lower Basket
Place heavily soiled items (like pots and
pans or dinner plates) in the bottom
basket. The more powerful spray jet
provides a better dishwashing result.
13
Upper basket
Daily Use
▶
The upper basket is designed
to hold items like glasses,
cups, saucers, plates, small
bowls and shallow pans.
▶
You can adjust the height of
the upper basket to create
more space for tall items in
the lower basket. See below.
▶
Place small items on the
foldable cup holder.
IMPORTANT!
Place sharp and pointed
items with the blade
pointing downward into the
knife rack, to keep
them out of harms way.
Adjusting the height of the upper basket
IMPORTANT!
Before you adjust its height,
Runner
Front safety
stop
1 Turn the front safety stops on
2
3
4
make sure the basket is
empty.
either side outwards.
Slide the empty bask
the runners.
Reinsert the higher or lower
set of rollers in the runners
and slide the basket all the
way back in.
Turn the front safety stops
inwards.
et out of
14
Daily Use
15
Daily Use
Detergent
Please use only a dedicated dishwasher detergent and follow the
related instructions and dosage on its package.
1.
If the lid is closed press the release
button (A) to open the lid.
2.
Put any detergent into compartment (B).
3.
If the programme has a pre-wash
phase, put a small quantity of
detergent on the inner part of the
appliance door. Refer to section
PROGRAMMES.
4.
Close the lid. Make sure that the
release button locks into position.
Multitabs
These Multitabs detergent tablets could include two different agents for
water
setting
softening, rinse aid and other functions. The softener and rinse aid
must be adjusted according to section BEFORE FIRST USE.
Usually the default setting performs well. If there are streaks, stains, shimmer etc.; refer to section TROUBLESHOOTING and BEFORE FIRST USE.
Detergent tablets do not fully dissolve with short programmes. That
may cause bad washing results and detergent residues.
If detergent without multifunction should be used again:
1. Save 3 to 5 tablets
2. Adjust the softener and rinse aid setting according to section BEFORE
FIRST USE.
3. Use
Multitabs
detergent tablets for the next 3 to 5 wash cycles.
16
Daily Use
Start a Programme
1.
Close the door.
2.
Press the ON/OFF button .
3.
Press the program button you want to select
programme indicator lights up.
4.
If desired select a start time for a delay start. Refer to section START
A PROGRAMME WITH DELAY.
5.
Press the START/PAUSE button to activate the programme or
the delay start.
The programme starts. The display acts now as countdown of the
remaining run-time.
The appliance remembers the last programme you used. The next
time the appliance will switch on, the appliance pre-selects the
programme last used.
Interrupt a Running Programme
To interrupt a programme run:
▶ Press the START/PAUSE button . In the display
and/or
▶
and then the required
is flashing.
Press the START/PAUSE button and/or close the door to continue
the programme from the point of interruption. Longer breaks may cause
bad cleaning results.
Activate / Deactivate options
On some models, the combination of all options is possible with all
programmes.
1. Switch on the appliance.
Press any of the currently extinguished washing procedure icons to
2.
select the washing procedure.
The display shows the duration of the programme.
If needed，press any unlit additional function button (1/2, wash block,
3.
increase the brightness).
If it can be matched with the current washing procedure,
17
You can set one option or combine all options.
Daily Use
the additional function indicates that the icon will be lit, and if it cannot
be matched, it will not be lit.
4.
If the currently selected washing procedure is rapid washing, washing and
single rinsing, press the and add the button, the washing time can be
increased by 10 minutes at a time ,up to three times .
5.
Press the button
Start a Programme with Delay
Set a start time by the following procedure in order to delay a programme
start:
1.
Set a programme.
2.
Press and hold the reservation button
required delay time (from 1 to 24hours).
3.
Press the START/PAUSE button .
▶ The display shows the countdown of the start delay. The count-
4.
down decreases with steps of 1 hour.
▶ When the countdown is completed, the programme starts.
to start the program．
until the display flashes the
Cancel a Delayed Start
When the current reservation time is displayed for 24h,
press the reservation
Afterwards the display flashes with the duration time
for the set programme.
The selected programme starts after a few seconds
button again to cancel the reservation
18
Daily Use
Cancel Start Delay / Programme
1. Press the ON/OFF button for about 1 second.
▶ The start delay is cancelled.
▶ The programme is aborted.
▶ The appliance is switched off.
2. Start a new programme and a delayed start if desired.
CAUTION!
If a programme will be aborted in the process of washing dishes,
the residue of detergent remains on the dishes. These can cause
damage to health! Make sure to rinse off the detergent residues
completely before using these dishes again.
Make sure that there is detergent in the detergent dispenser before
start a new programme.
End of Programme
When the programme is completed, the display shows and an accoustic signal is heard (if it is not switched off). The display switches off.
1. Press
standby mode automatically after 2 minutes.
2. Open the door.
3. Remove dishes:
There can be water on the sides and on the door of the appliance.
to switch off the appliance or the appliance switches into
CAUTION!
If the door will be opened immediately after the end of
programme, hot steam can escape. Danger of scalding!
Open the door carefully!
▶
Open the door slightly and leave it ajar (about 100 mm) to
help the drying process.
▶
Let the dishes become cold before removing them from the appli-
ance. Hot dishes damage more easily.
▶ First remove the items from the lower basket, then from the
upper basket.
Stainless steel becomes cool more quickly than the dishes.
Standby Mode
The switched on appliance will go into standby mode if it is not activated
within 2 minutes before starting a programme, or at the end of a
programme. This saves energy. The display switches off. To interrupt the
standby mode push one button.
19
Care and Cleaning
Inspect and clean your appliance at regular intervals. Basically any detergent
Care and Cleaning the Filters
1. A anticlockwise and
remove it.
2.
the latches and unplug A1 from A2.
3.
4.
5. B to its initial posi-
tion.
6.
until it locks.
washing results and possibly serious damage to the appliance.
If any filter is removed make sure that no solid object of any size
is left beyond these filters!
B.
A and put it into
B. Turn it clockwise
A press
20
Care and Cleaning
Care and Cleaning of the Spray Arms
Spray arms should be regularly inspected for dirt. If needed the spray
arms could be removed.
Upper spray arm
1. Turn bayonet socket to the left to
remove spray arm.
2. Remove remaining parts of food
remnants with a thin pointed object.
3. Flush with water and check all the
holes are clear.
4. Turn bayonet socket clockwise to
fasten spray arm.
Lower spray arm
1. Pull at the center to remove spray
arm.
2. Remove remaining parts of food
remnants with a thin pointed object.
3. Flush with water and check all the
holes are clear.
4. Place spray arm at the center with a
light push.
External Cleaning
CAUTION!
Never clean the appliance with a steam cleaner.
Never use bleach or other chlorinated detergents.
▶ Clean the appliance with a damp soft cloth.
▶ Only use neutral detergents. Do not use abrasive products, abrasive
cleaning pads or solvents.
▶ Clean the door seal with a damp soft cloth.
21
Troubleshooting
expertise. In case of a problem please check all shown possibilities and
follow below instructions before you contact an after sales service
CAUTION!
▶ Before maintenance, deactivate the appliance and disconnect
the mains plug from the mains socket.
▶ -
trical experts, because improper repairs can cause considerable
consequential damages.
The appliance does not start, or it stops during operation
Problem Possible cause Possible solution
The programme
does not start.
Rinse Aid Indicator
is lighted.
Appliance door is open. Close the appliance door.
Delay start is set. Refer to displayed time.
Mains plug is not connected in
the mains socket.
Fuse in the house circuit is
damaged.
Rinse aid dispenser is empty.
Connect the mains plug.
Replace the fuse.
Refill Rinse aid until full
Press and hold the START/
PAUSE button for 3 sec after
22
Troubleshooting
Error codes on the display
Problem Possible cause Possible solution
Acoustic alarm,
display shows
ALARMCODE
The appliance does
Acoustic alarm,
display shows
ALARMCODE
The appliance does
Acoustic alarm,
display shows
ALARMCODE
Leak: The drain
pump
runs permanently!
All other Alarmcodes:
1. Note Alarmcode
2. Contact Service ; refer to CUSTOMER SERVICE
Water tap is closed. • Open the water tap.
Note: Whenever Error ‘ ’ is
solved switch off the appliance
and restart the programm.
Water inlet hose has a kink or
a bend.
In case of aqua-stop system:
water protection is triggered;
the marker (C) is red.
Filter in the water inlet hose
is clogged.
Water inlet is clogged. Check water flow from tap.
Water pressure is too low. Contact your local water
Filters are clogged. • Scoop out as much water as
.
The drainage is blocked.
Anti-flood device is on:
• There are water leakages in
the appliance.
• The water inlet valve is
open and blocked.
• The drainage is blocked.
Make sure that the position of
the hose is correct.
The hose must be replaced.
Clean the filter at the inlet hose
connections at tap and the rear
of the appliance.
authority.
•
• Continue programme by
• Scoop out as much water as
• Make sure that drain water-
• Continue programme by
•
1 Close the water tap.
2 Disconnect appliance from
3 Contact Service.
.
possible.
pressing the
button.
possible.
connection and piping is
correct and not blocked.
pressing the
.
button
If the fault persists, contact
customer care.
power supply.
START/PAUSE
START/PAUSE
23
Troubleshooting
Washing Results are not satisfactory
Problem Possible cause Possible solution
The dishes are not
clean.
Filters are clogged.
Filters are not correctly assem-
bled and installed. correctly assembled and installed.
Spray arms are clogged. Remove remaining food remnants
Programme was not applicable
for the type of load and food
remnants.
Incorrect position of the items
in the baskets. Water could not
wash all items.
Spray arms could not turn freely. Make sure that the position of the
No detergent or insufficient
quantity of detergent in the detergent dispenser.
The wash cycle was interrupted
by a long break.
with a thin pointed object.
Make sure that the programme is
applicable for the type of load and
food remnants.
Make sure that the position of the
items in the baskets is correct and
that the water can easily wash all
items.
items in the baskets is correct and
does not cause the blockage of the
spray arms.
Make sure that you add the correct
quantity detergent in the dispenser
before you start a programme.
Do not open the door or cut power
supply during the wash cycle.
Whitish streaks,
stains or bluish layers
on glasses and dishes.
Released quantity of rinse aid is
too much.
Quantity of detergent was too
much.
Multitab detergent tablets used
with a short programme might
not fully dissolve.
Decrease the released quantity of rinse aid. Refer to section
DIFFERENT SETTINGS FOR RINSE
AID.
Make sure that you add the correct
quantity of detergent in the dispenser
before you start a programme.
Select a longer programme when
using Multitab detergent tablets.
24
Troubleshooting
Problem Possible cause Possible solution
Dry water drop
stains on glasses
and dishes.
The dishes are
wet.
The dishes are
wet and matte.
Rinse aid dosage is too low. Increase the released quantity of rinse aid.
Quality of rinse aid or Multitab. Cleaning product too old; change the
• Programme had no drying
phase.
• Programme had a low
temperature drying phase.
Rinse aid dispenser is empty.
Refer to section DIFFERENT SETTINGS
FOR RINSE AID.
product.
Open the door slightly and leave it ajar
(about 100 mm) to help the drying
process.
Refill rinse aid into the dispenser and
reset the rinse aid indicator.
Quality of rinse aid or Multitab. Cleaning product too old; change the
product.
Economic and Environmental Use
▶ It is not recommended to pre-rinse the dishes under running water.
▶ Select the washing programmes by type and degree of contamina-
tion of the dishes.
▶
Select the economy mode programme ECO for normal soiled items.
▶ The most economically use you will have with full loading.
▶
Only use the manufacturer’s recommended detergent or rinse
aid dosages.
25
WARNING!
Any i
refer to section SAFETY.
Free Standing Installation
1.
Installation under Worktop
1. The dimensions of the recess should
2. Put the appliance adjacent to the
Installation
Install the appliance on solid
ground. Adjust accurately all feet
INFORMATION!
Only with a correct level the
appliance door closes and seals
correctly.
at least agree with the dimensions in
.
slot. Make sure that all connections
(water, drain water, power) are neatly
positioned and connected.
3. Optional: Remove the worktop of
the appliance.
4.
level position.
5. Install the appliance carefully into
the recess.
WARNING!
If used as free standing appliance again, the worktop must be
remounted.
26
Installation
FreshWater Connection
IMPORTANT!
The appliance should be connected to
▶
▶
>10mm
▶
fig.A
1. Take note of water connection requirements.
▶ The dishwasher has a single valve water connection.
▶
We recommend a cold water connection for best performance
and energy efficiency.
▶
The incoming water temperature should not exceed
2. Take note of the permitted water pressure extremes.
▶
Lowest: 0.3 bar = 3 N/cm = 30kPa
▶
Where pressure is below 1 bar, contact a qualified plumber.
▶
Highest: 10 bar = 100 N/cm = 1MPa
Where pressure is above 10 bar, a pressure reduction valve
▶
must be installed. Contact a qualified plumber.
3. Connect the water inlet hose to an accessible water tap with
a 3/4” BSP connector (see fig.A). Ensure that there is no kink in
the inlet hose that could restrict the flow of water. A 90° bend
requires a minimum height of 200 mm for a kink-free curve.
▶
Ensure incoming water is clear. If the water pipes have not
been used for a long period of time, let the water run to make
sure it is clear with no impurities. Not doing so may result in
the water inlet hose getting blocked and damaging the appliance.
▶
If required, use a filter insert to filter out deposits from the
piping. The filter insert is available from your Authorised
Service Centre or Customer Care.
4. Tighten the hose coupling a further half turn after seal contact.
5. Check that the connection does not leak.
the water main using the new water
inlet hose supplied. Old hoses should
not be used.
▶
Do not shorten the inlet hose.
25°C.
2
2
27
Drain Water Connection
Fix the water drain hose properly to
the piping. The hose has to reach at one
point a height between 400 and 850 mm
above the appliance bottom line!
An extension hose for the water drain
hose must not exceed a total length of
4 m and must have the same diameter as
the water drain hose.
Following connections are possible:
Drain hose to sink
▶
▶
Drain hose to waste water
connection
▶
▶
Installation
Hang the drain hose with the
U-support over the edge of a sink
with adequate size.
against slipping.
The internal diameter of the stand
pipe with vent-hole must be minimum
40 mm.
Put the drain hose for approx
in the wastewater pipe.
Attach the U-suppor
▶
t and secu
80 mm
.
re it
Drain hose to sink connection
When connecting the drain hose to a
▶
sink trap with a drain hose spigot, make
sure that the drain hose is supported
to the height of the bench.
▶
Ensure the drain spigot has a minimum
hole diameter of 15 mm and it has been
CAUTION!
Ensure always that all connections (power supply, drain and fresh
water hose are firm, dry and leak free!
Take care these parts are never to be crushed, kinked, or twisted
If the supply cord is damaged, it must be replaced by the service
agent (see warranty card) in order to avoid a hazard.
)
drilled out.
28
Technical Data
Check the electrical data on the rating label (located on the left-hand
side of the dishwasher’s stainless steel inner door). Should the data on
the rating label be different to those specified below, consider those on
the rating label as correct.
Suppliers name or trade mark
Supplier´s model identifier
Rated capacity in standard
-place settings
Mains water pressure
Power voltage
Maximum current intensity
Total absorbed power
Colour
White
Stainless Steel
Black
Haier
HDW15V2*2
15
0.03-1 MPa (= 0.3-10 bar)
220-240 V (50Hz)
10 A
1720-2050 W
HDW15V2*2
29
Customer Service
We recommend our Haier Customer Service and the use of original spare
parts.
TROUBLESHOOTING.
▶ your local dealer or
▶ the Service & Support area at www.haier.com.au
or at www.haier.co.nz
To contact our Service, ensure that you have the following data available.
The information can be found on the rating plate at the door.
Model ____________________
Serial No. ____________________
30
Standards Test
Wash programme
Powdered detergent quantities 5 g pre-wash +
Rinse aid dosage level
Maximum number of place settings 15
Height adjustment of upper basket Ensure the upper basket is in its upper most
Recommended loading patterns
Eco
When the programme is finished, open the
door 100mm to help with drying
g main wash
28.75
position
31
Upper basket
3 3
Lower
basket
3
Upper basket with Utensil tray
Cutlery basket
2 3
1
4 5
Loading...