Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and
on your appliance. Always read and obey all safety messages.
DANGER
This is the safety alert symbol.
This symbol alerts you to potential hazards that can
kill or hurt you and others. All safety messages will
follow the safety alert symbol and either the word
“DANGER,” “WARNING” or “CAUTION.”
These words mean:
An imminently hazardous situation. You
could be killed or seriously injured if you
don’t immediately follow instructions.
A potentially hazardous situation
WARNING
CAUTION
All safety messages will tell you what the potential hazard is, tell you
how to reduce the chance of injury, and tell you what can happen if the
instructions are not followed.
which, if not avoided, could result in
death or serious bodily injury.
A potentially hazardous situation
which, if not avoided, may result in
moderate or minor injury.
1
WARNING
Fire Hazard
If the information in this manual is not followed exactly, a fire or
explosion may result causing property damage, personal injury or
death.
- Do not store or use gasoline or other flammable vapors and liquids in
the vicinity of this or any other appliance.
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s phone. Follow
the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer,
service agency or the gas supplier.
In the State of Massachusetts, the following installation instructions
apply:
Installations and repairs must be performed by a qualied or
•
licensed contractor, plumber, or gastter qualied or licensed by the
State of Massachusetts.
If using a ball valve, it shall be a T-handle type.
•
A exible gas connector, when used, must not exceed 3 feet.
•
2
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Connect anti-tip bracket to rear range foot.
Reconnect the anti-tip bracket, if the range is moved.
Failure to follow these instructions can result in death or serious burns
to children and adults.
INSTALLATION REQUIREMENTS
LOCATION REQUIREMENTS
IMPORTANT: Observe all governing codes and ordinances. Do not obstruct ow of
combustion and ventilation air.
It is the installer’s responsibility to comply with installation clearances specied
•
on the model/serial rating plate. The model/serial rating plate is located inside
the oven door on the right-hand side oven door trim.
The range should be located for convenient use in the kitchen.
•
Recessed installations must provide complete enclosure of the sides and rear of
•
the range.
To eliminate the risk of burns or re by reaching over heated surface units,
•
cabinet storage space located above the surface units should be avoided. If
cabinet storage is to be provided, the risk can be reduced by installing a range
hood or microwave hood combination that projects horizontally a minimum of 5”
(12.7 cm) beyond the bottom of the cabinets.
All openings in the wall or oor where range is to be installed must be sealed.
•
Do not seal the range to the side cabinets.
•
Cabinet opening dimensions that are shown must be used.
•
Grounded electrical supply is required. See “Electrical Requirements” section.
•
Proper gas supply connection must be available. See “Gas Supply Requirements”
•
section.
Contact a qualied oor covering installer to check that the oor covering can
•
withstand at least 200°F (93°C).
Use an insulated pad or ” (0.64 cm) plywood under range if installing range over
•
carpeting.
3
IMPORTANT: Some cabinet and building materials are not designed to withstand
the heat produced by the oven for baking and self-cleaning. Check with your builder
or cabinet supplier to make sure that the materials used will not discolor, delaminate
or sustain other damage.
GIVEN DIMENSIONS ARE MINIMUM CLEARANCES.
PRODUCT DIMENSIONS
ELECTRICAL REQUIREMENTS - U.S.A. ONLY
If codes permit and a separate ground wire is used, it is recommended that a
qualied electrical installer determine that the ground path is adequate and wire
gauge is in accordance with local codes.
Do not use an extension cord.
Be sure that the electrical connection and wire size are adequate and in
conformance with the National Electrical Code, ANSI/ NFPA No. 7-latest edition and
all local codes and ordinances.
A copy of the above code standards can be obtained from:
National Fire Protection Association
One Batterymarch Park
Quincy, MA 02269
4
Loading...
+ 14 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.