Page 1
FCD-JTHC80A- E
FCD-JTHC100A- E
Haier Household Electric Water Heater
User's Manual
Please read this manual before usage
Retain it for future reference
Rev. 01
Specific Number: 0040501044
Little Sea-ox
Qingdao Economic and Technological Development District
Haier Water Heater Co.,Ltd.
Add:Haier Garden,Qianwangang Road,Economic Development Zone,Qingdao, P.R.China
Website:http:// www.haier.com
Group
Page 2
Mark of
Haier Safe Water Heaters
Contents
See to the physical product for the appearance,color or pattern.
Friendly Hints
If water supply cutoff occurs in your home, please disconnect the power. Before
connecting power again, please open mixing valve to the mostest pitch of the hot water,
watch the showerhead until water comes out (indicating tank is full) and close mixing
valve. This can ensure a longer life of heating element.
If you live in high-rise apartment with water pressure beyond rated range (e.g. more
than 0.7 MPa), it is suggested you purchase a pressure reducing valve, which can
ensure reliable operation and normal service life of the water heater.
1.
2.
To ensure water heater life, a magnesium rod is used to resist corrosion. Like a battery,
magnesium rod is consumed and needs replacement. It is suggested you contact our
after-service once in two years to purchase a replacement magnesium rod. This can
ensure a much longer water heater life.
3.
Installation
2
Features
5
Safety precautions
3
2
Parameters
Installation
Electric circuit diagram
Before Usage
Dimensions
3
Setting environment
6-7
Operation
9
8
9
8
8-9
Packing list
Operation instructions
Attentions in operation
Attentions in installation
Cleaning and maintenance
FAQ
7
Friendly hints
10
This mark is the designation for Pre-Safe Expert of Haier
Water Heater Company, which indicates use of the company's
patented technology inside the product. It ensures you a safe
bath while monitoring whether your house ground wire is live or
not all the time. If this mark is lighted on, it indicates your house
ground wire has come live (poor grounding and live). In this
case, please immediately stop use and unplug from the power
supply, and remember not to touch any electric appliance shell
in your house. At the same time, immediately contact aftersales service and your property management company for
professional repair until the mark goes off.
Pre-Safe Expert will become the electric safeguard for your
family.
Note: Above hints only apply to electric water heaters.
Pre-safe Expert
FAQ*After service
Page 3
Rated voltage: 220V ~, 50Hz Dimensions: (see toFig. 1)
Power: 1200 W Weight: (see to Fig. 1)
Rated pressure: 0.75 MPa Volume :(see to Fig. 1)
Waterproof grade: Tap water pressure: not less than 0.05 MPaIPX4
Dear User,
Thanks for choosing Haier water heater product.
Haier products have good quality and excellent performance.To facilitate you to use the
product, please read the manual and operate accordingly.Please retain it for future
reference.
The international star service of Haier Group will always accompany you.No matter what
kind of problems you meet in usage,please contact with the local after-sales service
agent.We are at your service all the time.Thanks again for choosing Haier Product.
The water heater you purchased may not full comply with the figure in the manual due to
the improvement of product.We apologize for the inconvenience occurred therefrom.
1.
2.
3.
4.
5.
Safe:
High-quality imported heat-resistant stainless steel heating element, corrosion resistant
and more reliable. Over-temperature protection, tank liner over-pressure protection and
Safe Care patented design together with the function of monitoring and displaying of
live ground wire have become a real safeguard for family safety.
Durable:
Specially treated shell. Elegant and durable.
Tank liner produced with 3-layer liner enameling technology. More reliable quality.
Easy to use:
Heating temperature adjustable. Easy and flexible operation.
Water temperature adjustable between inlet temperature ~ 75 .
Product itself provided with a drain for regular tank cleaning and thus hot water of
higher quality.
Multi-purpose:
Closed structure suitable to connect several outlets for water use in locations like
washroom and kitchen. (outlet water is not suitable to drink) Suitable for use in homes,
enterprises and institutions, and service trade like hair & beauty saloons.
Horizontal installation, elegant style and space saving.
Your water heater is an improved product of this series. Please use it as instructed in
this manual.
Internal Cleaning: To ensure high working efficiency, heating elements and tank liner
of water heater shall be cleaned once in three years. Take care not to damage
protection layer on heating elements and tank liner inner surface. According to
different local water qualities and use habits, magnesium rod shall be periodically
replaced. If maintenance is needed, please contact local service station.
Tank Liner Cleaning: Do pull out power plug before cleaning. To clean, close water
inlet valve, open outlet valve, take down drain plug and empty the tank. Then open
water inlet valve to flush for several minutes until clean water flows out. Fit the drain
plug back.
Cleaning and Maintenance
FAQ
Packing List
Before Usage
Features
Parameters
Expansion
hook
(pcs)
User's
manual
(copy)
Electric
water
heater
(set)
Safety
valve
(pcs)
Expansion
bolt
(pcs)
Drain hose
(ply)
Quantity
Name
Phenomenon
Confirmation items
Remedy
Check
Check and clear
Check and open
Check power socket
Keep heating
Keep heating
Adjust temperature of water
Contact with service department
when are excluded
Contact with service department
when are excluded
Contact with service department
when are excluded
Adjust the flux of outlet water
Adjust the flux of outlet water
or use with constant water pressure
Adjust setting water temperature
No water supply or water pressure too low
Hot water access close
Hot water access close
No power to heater
Temperature not set to desired setting
Uncontrollable thermostat
heating time limit and setting
temperature not obtain
Defective heater
Setting water temperature not obtain
Temperature set too low
uncontrollable thermostat
Excessive water pressure
Unconstant water pressure
No water
Only cold
water but
pointer light
when heat
Only cold
water and
pointer not
light when heat
Heating pointer
always light
Insufficient
hot water
Unconstant
flow and
temperature
of water
Page 4
For the first use after installation, due to there's no water within the tank, first the city
water inlet valve and mixing valve must be opened. Close the mixing valve when water
flows out continuously from the showerhead or other outlets (the tank is full). Check
connections are free of water leakage, and insert the power plug.
Turn the knob to set your desired water heating temperature, which can be stepless
changed between cold water inlet temperature and 75 . In heating mode, heating lamp
is lighted on. Normally the knob shall be positioned at highest temperature. This
machine has a thermostat function, which automatically switches off the water heater
when temperature reaches the setting value, and switch on again when water
temperature decreases to certain value.
City water pressure 0.75 MPa will cause much water flowing out from safety valve
pressure relief vent. This is due to too big water pressure. Please ask after-sales
service for correction.
To avoid causing machine troubles, do not connect power before tank is full of water.
Adjust a suitable temperature before use, for water temperature above 50 may burn
your skin.
This product is closed water heater, which can supply hot water through pipe connection
to several points like bathroom (bathtub, washbasin, showerhead) and kitchen.
Provided hot water quantity can meet use demand, temperature setting shall be possibly
low. It can minimize heat dissipation, high-temperature corrosion and sedimentation,
ensuring a longer service life.
Regularly ask servicemen to make safety inspection, remove sediment on heating
elements, and check consumption of anode bar. Too much consumed anode bar shall be
replaced.
Heating adjustment can be made flexibly all year round adapting to climate changes. In
long-term out-of-use or maintenance, you can close city water pipe valve and set the
mixing valve to the highest water temperature rate after opening the safety valve handle.
Move up safety valve handle to drain the tank. To avoid injury, before next use, it is
suggested to first open hot water valve before switching on the water heater, exhausting
gas possibly retained in the pipeline. In this case, no smoke or fire is permitted near the
open valve. Carefully check and confirm all parts are in good condition.
This water heater shall only be repaired and maintained by qualified
servicemen. Improper maintenance may cause severe injury or damage.
Before opening or repairing water heater, please do pull out the power plug.
External Cleaning: Disconnect power supply before cleaning. Gently wipe with wet
cloth dipped with a little of mild detergent. Do not use gasoline or other solvents.
Finally dry with dry cloth. Keep water heater dry. Do not use cleansers containing
grinding agent (e.g. toothpaste), acids, chemical solvents (e.g. alcohol) or polishers to
clean.
L
N
E
HL
EH
E
BT
MT
L: Brown wire
N: Blue wire
MT:High temperature limiter
BT: Thermostat
HL: Heating indicator
EH: Heating element
E:Yellow/green wire
(Fig. 1)
1.
2.
3.
4.
5.
6.
Statement:
Note:
Before asking for service, please refer to troubleshooting section to resolve easy
problems.
Remarks:the permitted error limit of above parameters is 10%.
A
B
C
D
E
F
G
Hot water outlet
Cold water inlet
Heating element
Enamel tank
Wall-mounting bracket
Magnesium anode rod
Drain hole
Front View
Cutaway View
Bottom View
D
E
E
C
a1
e1
C1
d1
f1
b1
A
B
F
G
Model
Volume
Net
Weight
a1 b1 c1 d1 e1 f1
Dimensions
Electric Circuit Diagram
Operation Instructions
Attentions in Operation
Cleaning and Maintenance
Page 5
(Fig.4)
(Fig.5)
During installation, adequate space must be reserved for future maintenance and
repair. If the water heater is installed within decoration boards, the right board shall be
removable to facilitate removing the plastic cover during maintenance.
City water inlet pressure shall not be less than
Electric water heater shall be installed indoors with ambient temperature above 0 .
The pipes shall be collectively laid. Hot water outlet shall not be too far from use points.
In case farer than 8 m, hot water pipe shall have a thermal insulation to minimize heat
loss.
The mounting wall shall be firm and reliable to support twice the weight of water heater
full of water. Non-load bearing walls or air brick walls must have corresponding
protective measures like additional support, wall-through screws or back boards.
Electric water heater shall be located in a place easy for use, maintenance and with a
floor drainer. In case the tank or pipes leak, nearby or lower facilities shall not be
damaged. The installation location shall avoid being above toilet bowl, bathtub,
washbasin or doorframe, where will cause a suppressed or unsafe feeling to users.
Power socket for water heater shall be in a dry place free of water splash. (splashproof box is preferred)
Do not confuse inlet and outlet water pipes. Safety valve shall be installed at
designated position with no random modification.
0.05 MPa.
Installation
Attentions in Installation
Safety Precautions
Haier
C
²»
ÐÐ
£¡
²»ÐÐ
Á¢
¼´ ÓÃ ÓÚÏ´
Ô¡
²»
¿É
ÒÔ
²»
¿É
ÒÔ
Á¢¼´
ÓÃ
ÓÚ
Ï´
Ô¡
The product adopts Haier Safe Care patented technology. In normal installation, even in
severe case that ground wire is live due to wrong connection, the product Safe Care
technology can filter and efficiently ensure your safety. However, whenever your feel a
sensory current, please pull out the power plug and notify local after-service men in time. Do
not dismantle by yourself.
In winter in cold regions, for long-term outof-use, please lift the safety valve handle to
empty the water, avoiding ice formation
damaging the water heater.
Damaged power cord must be replaced
by after-service technicians with special
cable (factory provided). Other persons
shall not dismantle or repair. In addition,
do not place flammable matters nearby
the water heater.
Check if power meter and wire size are
consistent with water heater rated current.
If necessary, ask experienced qualified
electricians to check.
The water heater shall use 220 V / 50 Hz
power supply from a separate socket (no
multi-purpose socket) and be reliably
grounded. The power socket shall meet
national standard requirements. Power plug
pins shall be cleaned in time to avoid any
contamination causing accidents like fire.
Do not use damaged wire, socket or
appliances with loose plug, otherwise
accidents like electric shock, short circuit
and fire may occur. Make sure power plug
closely fits with power socket.
Power socket for water heater shall be
located in a dry place free of water spray.
Do not insert or pull the power plug with
wet hands, for accidents like electric
shock or injury may happen.
For first use after installation, the tank
must be full of water before connecting the
power. Otherwise, heating element
overheat may cause troubles.Children
taking shower must be attended by adults.
Please do not point the showerhead
towards human body when turning on or
off the faucet, avoiding to be scalded by a
small stream of hot water.
Connect to drain hose
Never do that
Be sure to act as per instructions
Description of the Symbols
Connection and Use of Safety Valve:
The safety valve should be connected to the cold water inlet pipe. Please check
carefully if the direction is correct after installation. The correct direction of
installation is that the arrowhead on the safety valve should point to the water heater.
If your water heater is not installed in a bathroom with sewage drain, please connect
the drain hose to the safety valve. Connect one end of the hose to the safety valve
vent and the other end to the sewage drain. The hose can be cut short or extended as
necessary. The hose shall be installed in a continuously downward direction and in a
frost-free environment.
The water may drip from the discharge pipe of the pressure relied device and that this
pipe must be left open to the atmosphere. Check safety valve once a month as follow:
move the small handle of safety valve, if there's water flowing out, safety valve is
normal; if there's no water flow, please contact local after-sales service station.
The pressure relief device is to be operated regularly to remove lime deposits and to
verify that it is not blocked.
Page 6
²»Òª°²×°ÓÚÎÞ·¨ÅÅË®µÄµØ·½
Do not install it outdoors.
Do not install it as stand-alone.
It shall be hung on firm and solid wall.
Do not install it in places unable to drain
water.
Installation must be made by installers of or designated by our company after-service
department.
The water heater shall be wall-mounted.
Before installation, make sure water heater rear wires are fit firmly. Determine an
installation location. Make four holes 12mm, 65 mm deep in the wall. Insert and fix
expansion hooks and expansion bolts in corresponding wall holes. Lift the water heater.
Insert wall rack onto the hooks and bolts. Fit flat washers, rear wires, spring washers
and nuts in turn onto the bolts. Tighten the nuts and check them firm. Install accessories
such as safety valve, drain hose as shown in Fig. 2. Use sealing compound to prevent
water leakage.
To facilitate installation and removal, it is suggested a G 1/2" movable nut is fitted at
appropriate locations on inlet and outlet pipes respectively. Find water supply location.
Connect inlet pipe, outlet pipe and city water pipe respectively to the use point.
Note: To avoid heat dissipation, hot water pipe shall not be too long.
For easy future maintenance and repair, adequate space must be reserved during
installation.
(Fig.3)
The tubes and pipes fitted on the product are inseparable parts of the Safe Care
technology, and shall not be removed by yourself. Otherwise, Haier shall not be liable
for any damages or injuries caused due to resulted potential risks.
Do not locate in freezing places. If
ice forms, tank and pipes will break,
causing scalding and leakage.
If a drain hose is connected, it shall be
connected to sewage drain, avoiding
spilling the room.
Hot water
valve
Cold water
valve
Mixing valve
Showerhead
Cold water inlet
Safety valve
Hot
water
outlet
Fig.2
For Installation Information Only
Setting Environment
Installation
Never do that
Be sure to act as per instructions
Description of the Symbols
Loading...