DW12-LFE SS
Dishwasher
DW12-LFE SS
Instructions for Use
0120505062
en
Safety Is a Good Habit to Develop
NOTICE
Carefully read the instructions contained in this manual, as they
provide important information which is essential to safe and proper
installation, use and maintenance of the appliance.
This appliance complies with the following EEC di-
rectives:
-73/23/EEC of 19 February 1973 (Low Voltage) and subsequent modifications;
- 89/336/EEC of 3 May 1989 (Electromagnetic
Compatibility) and subsequent modifications.
- Carefully dispose of the packing material.
- After removing the packing, check to make sure that the appli ance is not damaged. If in doubt, contact a qualified professional.
- The dishwasher must only be used by adults for the washing of
household dishes and cooking utensils.
- The appliance is not intended for use by young children or
inform persons without supervision.
- Young children should be supervised to ensure that they do
not play with the appliance.
- Keep detergents out of the reach of children, who must also
be kept away from the dishwasher when it is open.
- This appliance cannot be installed outdoors, not even if the
area in which it is installed is covered by a roof; it is also very
dangerous to leave it exposed to the rain and elements.
- Do not touch the heating element during or after a wash cycle.
- Do not lean or sit on the door when it is open as this could over
turn the dishwasher.
- If the appliance malfunctions, turn off water supply to the appli ance and disconnect the plug from the wall socket. Then, con sult the section entitled, "Troubleshooting." If you cannot solve
the problem, contact a service centre.
- Only specialised personnel are authorised to make repairs.
- Appliances which are no longer being used must be made inop erable by cutting the power supply cord and removing the door
lock.
- If the supply cord is damaged, it must be replaced by a special
cord or assembly available from the manufacturer or its ser vice agent.
- After installation, the power plug must be accessible.
- Fundamental rules to follow when using the appliance:
* Never touch the dishwasher when barefoot or with wet hands
or feet;
* We discourage the use of extension cords and multiple sockets;
* During installation, the power supply cord must not be exces sively or dangerously bent or flattened;
* If the appliance is not operating properly or maintenance must
be performed, disconnect the appliance from the power supply.
To maintain the EFFICIENCY and SAFETY of this appliance,we
recommend:
- call only the Service Centers authorized by the manufacturer.
- always use original Spare Parts
Close-up View (Control Panel)
A
A
ON-OFF Button
LCD Display
B
Delayed Start Button
C
Button For "Extra Drying" or "Half Load" or "Delay"
D
Start/Pause Button
E
Program Button
F
Program indicator
G
CDB
F
E
HG Q
I
L
Extra drying indicator
H
Half load indicator
I
Delayed start indicator
L
Time-remaining and delayed start indicator
M
Low rinse aid indicator
N
Low salt indicator
O
Cycle phase indicator
P
Selection cursor
Q
M
N
P
O
.1.
GB
Close-up View (Interior)
A
C
D
A
B
C
Upper Rack
Rack Height Adjustor
Top Spray Arm
B
E
H
F
G
G
H
I
I
J
K
L
Detergent and Rinse Aid Dispenser
Salt Container Cap
Third Sprayer
D
E
F
Width
Depth
Height
Capacity
Mains Water Pressure
Power Voltage
Total Absorber Power
Maximum current intensity
Lower Rack
Bottom Spray Arm
Washing Filter
Specifications
J
K
L
Water inlet hose with "Aquastop"
Drain hose
Power supply cord
60cm
60cm
85cm
12 standard place settings
0.03-0.6MPa
220-240V~ 50Hz
2150W
13A
GB
.2.
Salt
Salt
The hardness of the water varies from place to place. If hard
water is used in the dishwasher, deposits will form on the dishes
and utensils.
The appliance is equipped with a special softener that uses a salt
specifically designed to eliminate lime and minerals from the water.
Loading the Salt into the Softener
Always use salt intended for use with dishwashers.
The salt container is located beneath the lower rack and should
be filled as follows:
- When the "low salt indicator " (O) twinkles,you must fill the salt.
- Remove the lower rack and then unscrew and remove the cap
from the salt container;
- If you are filling the container for the first time, fill it with water;
- Place the end of the funnel (supplied) into the hole and append
about 2 kg of salt. It is normal for a small amount of water to
come out of the salt container.
- Carefully screw the cap on the back.
Adjusting Salt Consumption
The dishwasher is designed to allow for adjusting the amount of
salt consumed based on the hardness of the water used. This is
intended to optimize and customize the level of salt consumption
so that it remains at a minimum. Your local Water Board can
supply the degree of hardness of the water in your area.
To adjust salt consumption, proceed as follows:
The salt container must be filled when the "low salt" indicator light (located on the control panel) comes on.
To prevent the formation of rust, load the salt just before beginning a wash cycle.
- Unscrew the cap from the salt container;
- There is a ring on the container with an arrow on it (see figure),
If necessary, rotate the ring in an anticlockwise direction from
the "-" setting towards the "+" sign, based on the hardness of
the water being used.
It is recommended that adjustments be made in accordance with
the following scheme:
Water Hardness
Clarke
degrees
014
NQPS
PSTN
[TN
ç
dH
MNT
NUQQ
QRUV
[UV
mmol/l
MNIT
NIUQIQ
QIRUIV
[UIV
Selector
position
L
=?J?
jba
?H?
Salt
consumption
(Grams/cycle)
M
OM
QM
SM
Autonomy
(cycles/2kg)
SM
OR
L
QM
.3.
GB
Loading...