DW12-HFM
DW12-HFM
DW12-HFM ME
DW12-HFM SS
GB
DE
FR
IT ES
PT
NL
0120503790
Safety Is a Good Habit to Get Into
NOTICE
Carefully read the instructions contained in this manual, as they
provide important information which is essential to safe and proper
installation, use and maintenance of the appliance.
This appliance complies with the following EEC
directives:
-73/23/EEC of 19 February 1973 (Low Voltage) and subsequent modifications;
- 89/336/EEC of 3 May 1989 (Electromagnetic Compatibility)
and subsequent modifications.
- Carefully dispose of the packing material.
- After removing the packing, check to make sure that the appli ance is not damaged. If in doubt, contact a qualified professional.
- The dishwasher must only be used by adults for the washing of
household dishes and cooking utensils.
- The appliance is not intended for use by young children or
inform persons without supervision.
- Young children should be supervised to ensure that they do
not play with the appliance.
- Keep detergents out of the reach of children, who must also
be kept away from the dishwasher when it is open.
- This appliance cannot be installed outdoors, not even if the
area in which it is installed is covered by a roof; it is also very
dangerous to leave it exposed to the rain and elements.
- Do not touch the heating element during or after a wash cycle.
- Do not lean or sit on the door when it is open as this could
over turn the dishwasher.
- If the appliance malfunctions, turn off water supply to the appli ance and disconnect the plug from the wall socket. Then, con sult the section entitled, "Troubleshooting." If you cannot solve
the problem, contact a service centre.
- Only specialised personnel are authorised to make repairs.
- Appliances which are no longer being used must be made
inoperable by cutting the power supply cord and removing
the door lock.
- If the supply cord is damaged, it must be replaced by a special
cord or assembly available from the manufacturer or its ser vice agent.
- After installation, the power plug must be accessible.
- Fundamental rules to follow when using the appliance:
* Never touch the dishwasher when barefoot or with wet hands
or feet;
* We discourage the use of extension cords and multiple
sockets;
* During installation, the power supply cord must not be exces sively or dangerously bent or flattened;
* If the appliance is not operating properly or maintenance must
be performed, disconnect the appliance from the power
supply.
To maintain the EFFICIENCY and SAFETY of this appliance,we
recommend:
- call only the Service Centers authorized by the manufacturer.
- always use original Spare Parts
Close-up View (control panel)
A
G
A
ON-OFF light
"Eco" button
B
"1/2" button
C
BC D
FE
Low salt indicator light
D
Knob for selecting cycle
E
Handle for opening door
F
ON-OFF button
G
.1.
GB
Close-up View (Interior)
Upper Rack
A
Rack Height Adjustor
B
Top Spray Arm
C
Lower Rack
D
Technical characteristics
Width
Depth
Height
Capacity
Mains water pressure
Power voltage
Total absorber power
Bottom Spray Arm
E
Washing Filter
F
Detergent and Rinse Aid Dispenser
G
Salt Container Cap
H
Third Sprayer
I
12 standard place settings
60 cm
60 cm
85 cm
0.03-0.6 MPa
220-240V~50Hz
2100W
GB
.2.
Salt
Salt
The hardness of the water varies from place to place. If hard
water is used in the dishwasher, deposits will form on the dishes
and utensils.
The appliance is equipped with a special softener that uses a salt
specifically designed to eliminate lime and minerals from the water.
Loading the Salt into the Softener
Always use salt intended for use with dishwashers.
The salt container is located beneath the lower rack and should
be filled as follows:
- Remove the lower rack and then unscrew and remove the cap
from the salt container;
- If you are filling the container for the first time, fill it with water;
- Place the end of the funnel (supplied) into the hole and intro duce about 2 kg of salt. It is normal for a small amount of water
to come out of the salt container.
- Carefully screw the cap back on.
Adjusting Salt Consumption
The dishwasher is equipped with a system to adjust the level of
salt consumption in function of the hardness of the water being
used in order to optimize and customize the level of salt consumption while keeping it to a minimum.
To adjust the salt consumption level, follow these instructions:
- Unscrew the cap on the salt container;
- On the neck of the container there is an arrow (see figure to the
side).
- If necessary, turn the arrow in the anti-clockwise direc tion from the "-" setting to the "+" setting based on the hard ness of the water being used.
The salt container should be filled after about every 30 wash cycles.
To prevent the formation of rust, load the salt just before beginning a wash cycle.
It is highly recommended that the table be consulted when
making adjustments .
Water Hardness
Clarke
Level
degrees
010 MNT MNIT
1
2
ORRM QRUV QIRUIV
3
4
ºdH
mmol/l
NIUQIQNUQQNMOR
[UV[RM [UIV
Selector
position
L
=?J?
jba
Salt
consumption
(Grams/cycle)
OM
QM
SM?H?
Autonomy
(cycles/2kg)
LM
SM
QM
OR
.3.
GB
Loading...