Installation
Diagram
DW12-HFE2
The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over
to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help
prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling
of this product.
For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop
where you purchased the product.
GB
Code:0120504583
Safety Is a Good Habit to Develop
Close-up View (Interior)
NOTICE
Carefully read the instructions contained in this manual, as they
provide important information which is essential to safe and proper
installation, use and maintenance of the appliance.
This appliance complies with the following EEC
directives:
-73/23/EEC of 19 February 1973 (Low Voltage) and subsequent modifications;
- 89/336/EEC of 3 May 1989 (Electromagnetic Compatibility)
and subsequent modifications.
- Carefully dispose of the packing material.
- After removing the packing, check to make sure that the appli ance is not damaged. If in doubt, contact a qualified professional.
- The dishwasher must only be used by adults for the washing of
household dishes and cooking utensils.
- The appliance is not intended for use by young children or
inform persons without supervision.
- Young children should be supervised to ensure that they do
not play with the appliance.
- Keep detergents out of the reach of children, who must also
be kept away from the dishwasher when it is open.
- This appliance cannot be installed outdoors, not even if the
area in which it is installed is covered by a roof; it is also very
dangerous to leave it exposed to the rain and elements.
- Do not touch the heating element during or after a wash cycle.
- Do not lean or sit on the door when it is open as this could
over turn the dishwasher.
- If the appliance malfunctions, turn off water supply to the appli ance and disconnect the plug from the wall socket. Then, con sult the section entitled, "Troubleshooting". If you cannot solve
the problem, contact a service centre.
- Only specialised personnel are authorised to make repairs.
- Appliances which are no longer being used must be made
inoperable by cutting the power supply cord and removing
the door lock.
- If the supply cord is damaged, it must be replaced by a special
cord or assembly available from the manufacturer or its ser vice agent.
- After installation, the power plug must be accessible.
- Fundamental rules to follow when using the appliance:
* Never touch the dishwasher when barefoot or with wet hands
or feet;
* We discourage the use of extension cords and multiple
sockets;
* During installation, the power supply cord must not be exces sively or dangerously bent or flattened;
* If the appliance is not operating properly or maintenance must
be performed, disconnect the appliance from the power
supply.
To maintain the EFFICIENCY and SAFETY of this appliance,
we recommend:
- call only the Service Centers authorized by the manufacturer.
- always use original Spare Parts
L
K
V
J
I
J
L
H
A Cup Rack
B Upper Rack
C Rack Height Adjustor
D Top Spray Arm
A
B
C
D
E
F
G
G Washing Filter
H Detergent and Rinse Aid Dispenser
I Salt Container Cap
J Silverware Basket
Close-up View (control panel)
ON-OFF Light Low Salt Indicator Light
A
ON-OFF Button
B
Delay time display
C
Delay select Button
D
Half-load Button
E
DW12-HFE2
F
Low Rinse Aid Indicator Light
G
Handle For Opening Door
H
Cycle select button
I
Cycle indicator light
J
E Lower Rack
F Bottom Spray Arm
Technical characteristics
Width
Depth
Height
Capacity
Mains water pressure
Power voltage
Total absorbed power
K Knife Rack
L Third Sprayer
60 cm
60 cm
85 cm
12 standard place settings
0.03-0.6MPa
220-240V~ 50Hz
2150W
GB
GB
.2..1.
Salt
Detergent and Rinse Aid
Salt
The hardness of the water varies from place to place. If hard
water is used in the dishwasher, deposits will form on the dishes
and utensils.
The appliance is equipped with a special softener that uses a salt
specifically designed to eliminate lime and minerals from the
water.
Loading the Salt into the Softener
Always use salt intended for use with dishwashers.
The salt container is located beneath the lower rack and should
be filled as follows:
- Remove the lower rack and then unscrew and remove the cap
from the salt container;
- If you are filling the container for the first time, fill it with water;
- Place the end of the funnel (supplied) into the hole and intro duce about 2 kg of salt. It is normal for a small amount of water
to come out of the salt container.
- Carefully screw the cap back on.
Adjusting Salt Consumption
The dishwasher is designed to allow for adjusting the amount of
salt consumed based on the hardness of the water used. This is
intended to optimize and customize the level of salt consumption
so that it remains at a minimum. Your local Water Board can
supply the degree of hardness of the water in your area.
To adjust salt consumption, proceed as follows:
Detergent
Detergent specifically intended for use with dishwashers must
be used. The dispenser must be refilled before the start of
each wash cycle following the instructions provided in the
"Wash Cycle Table." The detergent dispenser is located on
the inside panel of the door.
Loading the detergent
To open cover "A" on the dispenser, press button "B".
The detergent for the wash cycle should be poured into compartment "C".
After the detergent has been placed in the dispenser, close
the cover and press down until it clicks in place.
C
A
Rinse Aid
This product makes dishes sparkle and helps them to dry without spotting. The dispenser is located on the inside panel of the
door and should be filled after every 80 wash cycles (or when
the rinse aid indicator light comes on for those models with this
feature).
Loading the Rinse Aid
To open the dispenser, turn the "C" cap in the anti-clockwise
direction and then pour in the rinse aid, making sure not to overfill.
The amount of rinse aid used for each cycle can be regulated by
turning the "F" dose adjustor, located beneath the "C" cap, with
a screwdriver. There are 6 different settings; the normal dosage
setting is 3.
Important
Proper dosage of the rinse aid improves drying.
If drops of water remain on the dishes or spotting occurs, the
dosage adjustor should be turned to a higher setting.
If the dishes have white streaks, turn the dosage adjustor to a
lower setting.
The salt container must be filled when the "low salt" indicator
light (located on the control panel) comes on.
To prevent the formation of rust, load the salt just before beginning a wash cycle.
- Unscrew the cap from the salt container;
- There is a ring on the container with an arrow on it (see figure to
the side), If necessary, rotate the ring in the anticlockwise
direction from the "-" setting towards the "+" sign, according to
water hardness.
It is recommended that adjustments be made in accordance with
the following scheme:
Water Hardness
Clarke
Level
degrees
014 MNT MNIT
1
2
PSTN QRUV QIRUIV
3
4
ºdH
mmol/l
NIUQIQNUQQNQPS
[UV[TN [UIV
Selector
position
L
=?J?
jba
Salt
consumption
(Grams/cycle)
OM
QM
SM?H?
Autonomy
(cycles/2kg)
B
C
F
C
Notice: To facilitate closing the cover, remove any excess
detergent on the edges of the dispenser.
LM
SM
QM
OR
GB
GB
.4..3.
Loading the Dishwasher
Turning on the Appliance
Before placing the dishes in the dishwasher, remove larger food
particles to prevent the filter from becoming clogged, which results in reduced performance.
If the pots and pans have baked-on food that is extremely hard to
remove, we recommend that they are soaked before washed. This
will eliminate the need for extra wash cycles.
Pull out the rack to load the dishwasher.
How to use the lower rack
We recommend that you place the most difficult to clean items on
the bottom rack: pots, pans, lids, serving dishes and bowls, as
shown in the figure to the right.
It is preferable to place serving dishes and lids on the sides of the
racks in order to avoid blocking the rotation of the top spray arm.
- Pots, serving bowls, etc. must always be placed face down.
- Deep pots should be slanted to allow the water to flow out.
- The lower rack features fold down tine rows (see fig.A) so that
larger or more pots and pans can be loaded.
- The silverware basket can be doubled (see fig.B) so that only
one section may be used when the silverware load is light. This
also makes space for additional pots and pans and it can also be
placed in the upper rack.
- Silverware should be placed in the silverware basket with the
handles at the bottom; if the rack has side baskets, the spoons
should be located individually into the appropriate slots. Espe cially long utensils should be placed in the horizontal position at
the front of the upper rack.
How to use the upper rack
The upper rack is designed to hold more delicate and lighter
dishware, such as glasses, cups and saucers, plates, small bowls
and shallow pans (as long as they are not too dirty).
- Position the dishes and cookware so that they do not get moved
by the spray of water.
Adjust the upper basket to the higher level and you have more
space to accommodate those taller pans and trays in the bottom
basket.
Shelf
Lean tall glasses and those with long stems against the shelf-not
against other items to be washed.
Place glasses, cups and small bowls on the additional cup rack.
The additional cup rack can be swivelled in or out as required(see
fig.C).
Knife rack
The knife rack clips onto the side of the top basket, giving you the
freedom to wash your large sharp knives separately and out of
harm’s way (see fig.D).
Lower Rack
Load for 12 Standard Settings
Load for 12 Standard Settings (for IEC-EN 50242 tests)
fig.A
fig.C fig.D
Upper Rack
fig.B
Starting a wash cycle
After having completed all of the installation steps in the preceding paragraphs, turn on the water all the way and press the ONOFF button (B) located on the control pannel. The "A" indicator
light will come on. At this point, the appliance is on but you must
wait a few seconds before programming the cycle setting.
Setting and Starting a wash Cycle
Select the desired cycle by pressing the selector button (I). Each
time the button is pressed, one of the "J" cycle indicator lights will
come on in succession. Choose the wash cycle you feel is most
appropriate for the type of dishes that need washing (consult the
wash cycle table contained in this manual. After a few seconds,
the wash cycle has begun and can no longer be changed. If
necessary, read the paragraph entitled "Cancelling or modifying a
cycle" .
Cancelling or modifying a cycle
A cycle that is underway can only be modified if it has only been
running for a short time. Otherwise, the detergent may have already been used, and the appliance mayhave already drained the
wash water. If this is the case, the detergent dispenser must be
refilled (see the paragraph entitled, "Loading the Detergent"). To
modify a cycle that is already underway, press the ON/OFF button
(B), all of the settings will be cancelled. To set a new cycle, follow
the instructions contained in the paragraph entitled "Setting and
starting a wash cycle".
Wash Cycle Program Light
The dishwasher is equipped with a LED indicator light (J) that turns
on when the appliance is running the wash cycle.
At the end of the wash cycle
Six beeps will indicate that the wash cycle has finished and the
cycle indicator light (J) for the cycle will begin to die out. Turn off
the appliance using the ON-OFF button. Turn off the water supply
to the appliance and open the door. Wait a few minutes before
unloading the dishwasher to avoid handling the dishes and utensils while they are still hot and more susceptible to breakage. They
will also dry better.
Setting the Wash Cycle with a Delayed Start Time
By pressing the "D" button (see close-up view-'Control panel")
the start of wash cycle can be delayed for between 1 to 12
hours.
Each time the button is pressed, the display (C) will show the
number of hours for the delay period. Choose the amount of
time desired. After selecting the wash cycle, a short acoustic
signal will sound and after a few seconds, the delay time on
the display will blink, This indicates that the countdown has
begun.
After the time has lapsed, the cycle will start.
NOTE:
During the delay period, it is preferable not to change any of
the settings, If this is necessary, all of the settings must be
cancelled by pressing the ON/OFF button (B).
At this point, all of the steps for "setting the wash cycle with a
Delayed Start Time" and "Setting and Starting a wash cycle"
must be repeated, following the instructions contained in the
corresponding sections.
If the door is opened to the unit during the delay period, the
countdown will stop. It wil begin again when the door is closed.
All of the wash cycle set to reverse time function, we may in
focus stat circulate time.
Wash Cycle adjustment Buttons
1/2 load Button
This button (see "close-up View - Control Panel", letter"E")
makes it possible to wash dishes using only the upper rack if
there are not enough dishes for a full load. This will allow you
to save on water and power. It can be used before setting
any of the wash cycle, except for the intensive cycle ( if included in the wash cycle table). Please keep in mind that the
amount of detergent should also be cut in half.
GB
GB
.6..5.
Energy Saving Tips
Wash Cycle Table
- It is important to try and run the dishwasher when it is fully
loaded in order to save on energy. In order to prevent
odours from forming and food from caking onto the dishes,
you can use the soak cycle.
- Choose the right wash cycle: the choice depends on the
type of dishware, cookware and utensils being washed and
how dirty they are.
How to Keep Your Dishwasher in Shape
- Use the right amount of detergent: if you use too much detergent,
the result will not be cleaner dishes, but, rather, a greater
negative impact on the enviroment.
- There is no utility in rinsing dishes, cookware and utensils
before placing them in the dishwasher.
Cycle
Heavy Duty
Normal Wash
Rapid Wash
Cycle Selection
Information
Very dirty dishes, pots and
pans. (not to be used with delicate items)
Normal dirty dishes, pots and
pans. standard daily cycle.
Economic, fast cycle to be used
on not very dirty dishes right after they are used. No drying
cycle.
Desciption of Cycle Detergent Rinse Aid
Pre-wash with hot water.
.
.
.
Extended wash at 70
Rinse with cold water.
Rinse with hot water.
Drying.
Pre-wash with cold water.
Extended wash at 55
Rinse with cold water.
Rinse with hot water.
Drying.
Short wash at 40
Cold rinse .
30g
30g
15g
After Every Wash
After every wash, turn off the water supply to the appliance and
leave the door slightly ajar so that moisture and odours are not
trapped inside.
Remove the Plug
Before cleaning or performing maintenance, always remove the
plug from the socket. Do not run risks.
No Solvents or Abrasive Cleaning Products
To clean the exterior and rubber parts of the dishwasher, do not
use solvents or abrasive cleaning products. Use a cloth and warm
soapy water.
To remove spots or stains from the surface of the interior, use a
cloth dampened with water and a little white vinegar, or a cleaning product made specifically for dishwasher.
Moving the Appliance
If the appliance must be moved, try to keep it in the vertical position.
If absolutely necessarty, it can be positioned on its back.
Seals
One of the factors that cause odours to form in the dishwasher is
food that remains trapped in the seals. Periodic cleaning with a
sponge will prevent this from occuring.
When You Go on Holiday
When you go on holiday, it is recommended that you run a wash
cycle with the dishwasher empty and then remove the plug from
the socket, turn off the water supply and leave the door of the
appliance slightly ajar. This will help the seals last longer and prevent odours from forming within the appliance.
Light Wash
(IEC-EN50242)
Soak
Normal dirty dishes, pots and
pans. standard daily cycle.
Pre-wash of dishes, pots and
pans while waiting for the load to
be completed after the subsequent meal.
Pre-wash with cold water.
Extended wash at 50 °C.
Rinse with cold water.
Rinse with hot water .
Drying.
Short cold wash to prevent food residue from drying on the dishes .
25+5g
ERF
GB
GB
.8..7.
Cleaning and Special Maintenance
Installation
Filter Assembly
For best performance and results, the filter assembly must be
cleaned.
The filter efficiently removes food particles from the wash water,
allowing it to be recirculated during the cycle. For this reason, it
is advisable to remove the larger food particles trapped in the
filter after each wash cycle by rinsing the semi-circular filter and
cup (A) under running water. To remove the filter assembly, pull
on the cup handle in the upward direction. The entire filter assembly (made up of the semicircular filter (A) and fine filter (B))
should be cleaned at least once a month. To clean the filter and
fine filter, use a cleaning brush. Then, reassemble the filter parts
as shown in the figures below and refit the entire assembly in the
dishwasher, positioning it in its seat and pressing downward.
The dishwasher must never be used without the filters. Improper
replacement of the filters may reduce the performance of the
appliance and damage dishes and utensils.
Troubleshooting
It may occur that the dishwasher does not function or does not
function properly. Before calling for assistance, See what can
be done first: have you forgotten to press one of the buttons or
to perform an essential operation?
The Dishwasher Does Not Start
Have you checked whether:
- the plug is pushed into the socket correctly;
- the power is on in the house;
- the door is closed properly;
- the ON-OFF switch is on "ON";
- the water supply is turned on.
The Dishwasher Does Not Load Water
Have you checked whether:
- the water is turned on and the hose is connected properly;
- the water supply to the house is on and has sufficient pressure;
- the water supply hose is crimped or bend;
- the filter for the water supply hose is clogged.
Cleaning the Spray Arms
It may happen that food particles become encrusted on the
sprayer arms and block the holes (see "Close up view [interior]",
letters D-F ). Check the sprayer arms periodically and clean them
when needed.
A
B
Cleaning the Water Inlet Filter
Periodically clean the water inlet filter located on the outlet of the
water supply tap.
After turning off the water tap, unscrew the end of the water supply hose, remove the filter and clean it carefully under running
water. Then, return the filter to its place and tighten the water
supply hose back into position.
The Dishwasher Does Not Drain
Have you checked whether:
- the drain hose is crimped or bend.
Lime Deposits or a White Film Form on the Dishes
Have you checked whether:
- the lid to the salt container is closed properly;
- the rinse aid dosage is correct.
If, despite all these checks, the dishwasher still does not function
and/or the problem persists, contact the nearest authorised service centre and provide them with the following information:
- the nature of the problem;
- the model type number (Mod...) and the serial number (S/N...),
which are indicated on the plate located on the side of the inner
part of the door.
Never call on unauthorised technicians and refuse to allow
parts to be installed that are not original spare parts.
Positioning the Appliance
Position the appliance in the desired location. The back should
rest against the wall, and the sides along the adjacent cabinets
or wall. The dishwasher is equipped with water supply and drain
hoses that can be positioned to the right or the left to facilitate
proper installation.
Levelling the Appliance
Once the appliance is positioned, adjust the feet (screwing them
in or out) of the dishwasher until it is level. In any case, the
appliance should not be inclined more than 2°. If the appliance
is level, it will help ensure proper performance.
Cold Water Connection
Connect the cold water supply hose to a threaded 3/4 (gas)
connector and makeing sure that it is fastened tightly in place
(see Fig.1).
If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the
water is clear and free of impurities. If this precaution is not
taken, there is a risk that the water inlet can get blocked and
damage the appliance.
Hot Water Connection
The water supply to the appliance can also be connected to
the house's hot water line (centralised system, heating system),
as long as it does not exceed a temperature of 60.In this
case, the wash cycle time will be shortened by about 15 minutes and the wash efficiency slightly reduced.
The connection must be made to the hot water line following
the same procedures as those for the connection to the cold
water line.
Fig.1
Anti-Flooding Protection
The dishwasher is equipped with a system that stops the supply
of water in the event of a problem with the water supply hose, or
leaks within the unit, in order to prevent damage to your home. If
for any reason the box containing the electrical components happens to get damaged, remove the plug of the appliance from the
socket immediately. In order to guarantee that the anti-flooding
feature operates properly, the box "A" with the water supply hose
must be attached to the water supply tap as shown in Fig.1. No
other type of connection is acceptable. The water supply hose
must not, under any circumstances, be cut, as it contains electrical parts which are live. If the length of the hose is not adequate
to make a proper connection, the hose must be replaced with
one which is long enough. This hose is available upon request
from specialised retailers and service centres.
Fig.2
Drain Hose Connection
Insert the drain hose into a drain pipe with a minimum diameter
of 4cm, or let it run into the sink, making sure to avoid bending
or crimping it. Use the special plastic support that comes with
the appliance (see Fig.2). The free end of the hose must be at
a height between 40 and 100 cm and must not be immersed in
water.
Attention:
The special plastic hose support must be solidly fastened to
the wall to prevent the drain hose from moving and allowing
water to spill outside the drain.
Electrical Connection
After making sure that the voltage and frequency values for the
current in the home correspond to those on the rating plate (located on the stainless steel inner door of the appliance) and
that the electrical system is sized for the maximum voltage on
the rating plate, insert the plug into an electrical socket which is
earthed properly (the earthing of the appliance is a safety requirement mandated by law).
If the electrical socket to which the appliance must be connected
is not appropriate for the plug, replace the plug rather than using adaptors or the like as they could cause overheating and
burns.
GB
GB
.10..9.
Loading...