Domestic Dishwasher
DDW300S
DDW300W
GB
Code: 0120504927
Safety Is a Good Habit to Get Into
Close-up View (Interior)
IMPORTANT
Carefully read the instructions contained in this manual, as it provides information that is essential to safe and proper installation,
use and maintenance of this appliance.
This appliance complies with following EEC directives:
- 73/23/EEC of 19/02/73(Low Voltage)and subsequent
modifications;
- 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and
subsequent modifications.
- Carefully dispose of the packing material.
- After removing the packing, check to make sure that the appli ance is not damaged. If in doubt, contact a qualified professional.
- The dishwasher must only be used by adults for the washing of
household dishes and cooking utensils.
- Fundamental rules to follow when using the appliance:
* Never touch the dishwasher with wet hands;
* We discourage the use of extension cords and multiple sockets;
* During installation, the power supply cord must not be exces sively or dangerously bent or flattened;
* If the appliance is not operating properly or, requires
maintenance, disconnect the appliance from the power supply.
- Keep detergents out of the reach of children. Also keep chil
dren away from the dishwasher when it is open to reduce the
risk of injury.
- This appliance cannot be installed outdoors or exposed to the
rain and elements. Not even if the area in which it is installed is
covered by a roof. It is very dangerous.
- Do not lean or sit on the door when it is open, as this could
overturn the dishwasher.
- If the appliance malfunctions, turn off water supply to the appli ance and disconnect the plug from the wall socket. Then, refer
to the "Troubleshooting". If you cannot resolve the problem,
contact an authorised service agent.
- Only specialised personnel are authorised to make repairs.
- Appliances which are being discarded must be made
inoperable by cutting the power supply cord and removing the
door lock.
- The appliance must be positioned so that the plug or isolating
switch is accessible.
- If the supply cord is damaged, it must be replaced by the manu facturer or an authorised service agent.
Warning:
Dishwasher Detergents can be extremely dangerous, if swallowed.
Avoid contact with skin and eyes and keep children away from the
dishwasher when the door is open.
Check that the detergent receptable is empty after completion of the
wash cycle.
K
J
I
H
A Cup Rack
B Upper Rack
A
B
V
C
D
E
F
J
G
L
G Washing Filter
H Detergent and Rinse Aid Dispenser
Close-up View (control panel)
D
ON-OFF Button
A
ON-OFF Light
B
"HALF LOAD" Button
C
Low rinse aid indicator light
D
C Rack Height Adjustor
D Top Spray Arm
E Lower Rack
F Bottom Spray Arm
BCEF
HG
I
Cycle indicator light
F
Cycle select button
G
"HALF LOAD" indicator light
H
Delay indicator light
I
A
Technical characteristics
Width
Depth
J
Height
Capacity
Mains water pressure
Power voltage
Total absorber power
I Silverware basket
J Knife rack
K Third Sprayer
60 cm
60 cm
85 cm
12 standard place settings
0.03-0.6MPa
220-240V~ 50Hz
2150W
Water heating indicator light
E
.1.
Delay select button
J
.2.
Detergent and Rinse Aid
Loading the Dishwasher
Detergent
Detergent specifically intended for use with dishwashers must
be used. The dispenser must be refilled before the start of each
wash cycle following the instructions provided in the "Wash Cycle
Table". The detergent dispenser is located on the inside panel of
the door.
Loading the detergent
To open the "A" cover on the dispenser, press the "B" button.
The detergent for the wash cycle should be poured into the "C"
compartment.
After the detergent has been placed in the dispenser, close the
cover and press down until it clicks into place.
C
A
B
Notice: To enable the cover to close, remove any excess detergent from the edges of the dispenser.
Rinse Aid
This product makes dishes sparkle and helps them to dry without spotting. The dispenser is located on the inside panel of the
door and should be filled after approx every 80 wash cycles (or
when the "low rinse aid" indicator light comes on for those models with this feature).
Loading the Rinse Aid
Regardless of the type of detergent dispenser installed on your
appliance, you must proceed as indicated below when loading
the rinse aid.
To open the dispenser, turn the "C" cap in an anti-clockwise
direction and then pour in the rinse aid, making sure not to overfill.
The amount of rinse aid used for each cycle can be regulated by
turning the "F" dose adjustor, located beneath the "C" cap, with
a screwdriver. There are 6 different settings; the normal dosage
setting is 3.
Important
Proper dosage of the rinse aid improves drying.
If drops of water remain on the dishes or spotting occurs,
the dosage adjustor should be turned to a higher setting.
If the dishes have white streaks, turn the dosage adjustor
to a lower setting.
C
F
C
Before placing the dishes in the dishwasher, remove larger food
particles to prevent the filter from becoming clogged, which results in reduced performance.
If the pots and pans have baked-on food that is extremely hard to
remove, we recommend that they are soaked before washed. This
will eliminate the need for extra wash cycles.
Pull out the rack to load the dishwasher.
How to use the lower rack
We recommend that you place the most difficult to clean items on
the bottom rack: pots, pans, lids, serving dishes and bowls, as
shown in the figure to the right.
It is preferable to place serving dishes and lids on the sides of the
racks in order to avoid blocking the rotation of the top spray arm.
- Pots, serving bowls, etc. must always be placed face down.
- Deep pots should be slanted to allow the water to flow out.
- The lower rack features fold down tine rows (see fig.A) so that
larger or more pots and pans can be loaded.
- The silverware basket can be halved (see fig.B) so that only
one section may be used when the silverware load is light. This
also makes space for additional pots and pans and it can also be
placed in the upper rack.
- Silverware should be placed in the silverware basket with the
handles at the bottom; if the rack has side baskets, the spoons
should be located individually into the appropriate slots. Long
utensils should be placed in a horizontal position in the upper
rack.
How to use the upper rack
The upper rack is designed to hold more delicate and lighter
dishware, such as glasses, cups and saucers, plates, small bowls
and shallow pans (as long as they are not too dirty).
- Position the dishes and cookware so that they do not get moved
by the spray of water.
The upper rack can be adjusted for height by using the knobs located on both sides of the rack itself (see fig.C).
Adjust the upper basket to the higher level and you have more
space to accommodate those taller pans and trays in the bottom
basket.
Shelf
Lean tall glasses and those with long stems against the shelf-not
against other items to be washed.
Place glasses, cups and small bowls on the additional cup rack.
The additional cup rack can be swivelled in or out as required(see
fig.D).
Knife rack
The knife rack clips onto the side of the top basket, giving you the
freedom to wash your large sharp knives separately and out of
Lower Rack
Load for 12 Standard Settings
fig.A
fig.C
fig.E
Upper Rack
fig.B
fig.D
harm’s way (see fig.E).
.3. .4.
Starting the Appliance
Wash Cycle Table
Starting a wash cycle
After having completed all of the installation steps in the preceding paragraphs, turn on the water to the unit, partially open the
door of the dishwasher, and press the ON-OFF button "A" located on the control panel. The "B" indicator light will come on.
At this point, the appliance is on and ready to be programmed.
Setting and Starting a wash Cycle
Choose the desired cycle by pressing the cycle selection button
"G". Each time it is pressed, the cycle indicator lights "F" will
change to indicate the cycle selected.
Choose the wash cycle you feel is most appropriate for the type
of dishes that need washing (consult the wash cycle table contained in this manual, especially when first using the appliance).
Close the door and after a few seconds, The wash cycle will begin.
Read the paragraph entitled, "Cancelling or changing a cycle while
underway. "The end of the cycle will be signalled by six beeps,
and the indicator light "F" will extinguish.
Cancelling or changing a cycle while underway...
Premise: A cycle that is underway can only be changed if it has
only been running for a short time.
Otherwise, the detergent may have already been used, and the
appliance may have already drained the wash water. If this is the
case, the detergent dispenser must be refilled (see the paragraph
entitled, "Loading the Detergent").
To change the cycle currently underway, open the door, press
the "G" programming button and hold it in for about 5 seconds.
Once the cycle has been cancelled, the dishwasher will emit a
short acoustic sound and the relative indicator light will turn off.
To set a new wash cycle, follow the instructions contained in the
paragraph entitled, "Setting and Starting a Wash Cycle."
At the end of the wash cycle...
Six beeps will indicate that the wash cycle has finished and the
cycle indicator light “F” will begin to extinguish. Open the door,
turn off the appliance using the ON/OFF switch and turn off the
water supply to the unit. Wait a few minutes before removing the
dishes so as to avoid handling them while still hot (when they
are more susceptible to breakage) and to get better drying results.
Setting The Start Delay Time
Open the door of the dishwasher partially. Press button "J" (see,
Close-up View" Control Panel") to delay the starting time for a
wash cycle.
.1st press, “2h” indicator comes on, the cycle will start in 2 hours.
.2nd press, “4h” light indicator comes on, the cycle will start in 4
hours.
.3rd press, “6h” light indicator comes on, the cycle will start in 6
hours.
.4th press, “2h” and “6h” light indicators come on, the cycle will
start in 8 hours.
.5th press, “4h” and “6h” light indicators come on, the cycle will
start in 10 hours.
.6th press, “2h” , “4h” and “6h” light indicators come on, the cycle
will start in 12 hours.
.last press, all light indicators will extinguish and you can reset.
After selecting the delay time, the wash cycle can be set, as
explained in "Starting a wash cycle..." There will be a short acoustic signal, and at this point the delay period will begin to count
down. During this period the delay indicator light (I) will blink. At
the end of the delay time, the indicator will stop blinking and the
cycle will start.
NOTE:
a) During the delay period, none of the settings can be modified.
If necessary, they can be cancelled by pressing cycle selector
"P" for about 5 seconds.
b) If the power to the appliance goes off or the door is opened
during the delay period, the clock will stop the countdown. It will
start again when the power has come back on, or when the door
has been closed.
Wash Cycle Adjustment Buttons
1/2 Load Button
This button (see" Close-up View-Control Panel", letter "C") makes
it possible to wash dishes using only the upper rack if there are
not enough dishes for a full load, This will allow you to save on
water and electrical energy.
Cycle
Intensive
Normal Wash
Light Wash
Glassware
Rapid Wash
Soak
Cycle
Selection
Information
Very dirty dishes,
pots and pans. (Not
to be used with delicate items)
Normal dirty dishes,
pots and pans. Standard daily cycle.
Normal dirty dishes,
pots and pans without
dried on residue.
Economic, fast cycle to be
used for delicate items which
are sensitive to higher. Run
immediately after dishes are
used.
Economic, fast cycle to
be used to on not very
dirty dishes right after
they are used. No drying cycle.
Pre-wash of dishes,
pots and pans while
waiting for the load to
be completed after the
subsequent meal.
The cycle of heat washing and dry tableware.
Description of
Cycle
Pre-wash with hot water.
Extended wash at 70K
Rinse with cold water.
Rinse with hot waterK
Drying.
Pre-wash with cold water.
Extended wash at 50.
Rinse with cold water.
Rinse with hot water.
Drying.
Pre-wash with cold water.
Extended wash at 50K
Rinse with cold water.
Rinse with hot waterK
Drying.
Wash at 45.
Rinse with warm water.
Hot rinse.
Drying.
Short wash at 40.
Cold rinse.
Short cold wash to prevent
food residue from drying on
the dishes K
Heat washing.
Detergent Rinse Aid
30g
5+25g
30g
15g
ERF
15g
.5.
Heat wash
.6.
Energy Saving Tips
Troubleshooting
-It is important to try and run the dishwasher when it is fully
loaded in order to save on energy. In order to prevent odors
from forming and food from caking onto the dishes, you can run
the soak cycle.
-Choose the right wash cycle: the choice of cycle depends on
the type of dishware, cookware and utensils being washed and
how dirty they are.
How to keep Your Dishwasher in Shape
After Every Wash
After every wash, turn off the water supply to the appliance and
leave the door slightly ajar so that moisture and odors are not
trapped inside.
Remove the plug
Before cleaning or performing maintenance, always remove the
plug from the socket. Do not run risks.
No solvents or Abrasive Cleaning Products
To clean the exterior and rubber parts of the dishwasher, do not
use solvents or abrasive cleaning products. Rather, use only a
cloth and warm soapy water.
To remove spots or stains from the surface of the interior, use a
cloth dampened with water and a little while vinegar, or cleaning
product made specifically for dishwashers.
Cleaning and Special Maintenance
Filter Assembly
For best performance and results, the filter assembly must be
cleaned frequently.
The filter efficiently removes food residue from the wash water,
allowing it to be recirculated during the cycle. For this reason, it
is a good idea to remove the larger food particles trapped in the
filter after each wash cycle by rinsing the "A" semi-circular filter
and cup under running water. To remove the filter assembly, pull
on the cup handle in an upward direction. The entire filter assembly (made up of the "A" semicircular filter and the "B" fine filter)
should be cleaned at least once a week.
To clean the filter and the fine filter, use a cleaning brush. Then,
reassemble the filter parts as shown in the figures below and
reinsert the entire assembly in the dishwasher, positioning in its
seat and pressing downward.
The dishwasher must never be
used without the filters. Improper
replacement of the filters may reduce the performance level of the
appliance and damage dishes and
utensils.
.7.
-Use the right amount of detergent: if you use too much detergent, the result will not be cleaner dishes, but, rather, a greater
negative impact on the environment.
When You Go on Holiday
When you go on holiday, it is recommended that you run a wash
cycle with the dishwasher empty and then remove the plug from
the socket, turn off the water supply and leave the door of the
appliance slightly ajar. This will help the seals last longer and
prevent odours from forming within the appliance.
Moving the Appliance
If the appliance must be moved, try to keep it in a vertical position.
If absolutely necessary, it can be positioned on its back.
Seals
One of the factors that cause odours to form in the dishwasher is
food that remains trapped in the seals. Periodic cleaning with a
damp sponge will prevent this from occurring.
Cleaning the Spray Arms
Check the spray arms periodically and clean them when
needed.
A
B
Cleaning the Water Inlet Filter
Periodically clean the water inlet filter (see figure) located on the
outlet of the water supply tap.
After turning off the water tap, unscrew the end of the water supply hose, remove the filter and clean it carefully under running
water. Then, return the filter to its place and tighten the water
supply hose back into position.
If the dishwasher does not function or does not function properly.
Before calling for assistance, check to see what can be done
first: have you forgotten to press one of the buttons or to perform an essential operation?
The Dishwasher Does Not Start
Have you checked whether:
- the plug is pushed into the socket correctly;
- the power is on in the house;
- the door is closed properly;
- the ON-OFF switch is on "ON";
- the water supply is turned on.
The Dishwasher Does Not Fill With Water
Have you checked whether:
- the water is turned on and the hose is connected properly;
- the water supply to the house is on and has sufficient pressure;
- the water supply hose is crimped or bent;
- the filter in the water supply hose is clogged.
The Dishes Are Not Clean
Have you checked whether:
- Dishwasher was loaded properly. Jets of water could not reach
all parts of the dishes, etc;
- Too many items in the rack;
- Items in the rack were touching each other;
- Not enough detergent was added to dispenser;
- Selected wash programme was intensive enough;
- Rotation of spray arm was obstructed by dish, etc;
- Nozzles in spray arm are blocked by remnants of food;
- Coarse or fine filter or microfiller is blocked;
- Filters have been incorrectly fitted;
- Drain pump is jammed;
The Dishwasher Does Not Drain
Have you checked whether:
- the drain hose is crimped or bent.
Lime Deposits or a White Film Form on the Dishes
Have you checked whether:
- the rinse aid dosage is correct.
Error Messages
The dishwasher is equipped with a safety system that is able to
detect operating problems and malfunctions. These malfunctions
are signalled by the rapid blinking of one of the "M" program LEDs.
Only in the case where the indicator light for the soak cycle (see
table for cycles) blinks rapidly should you cancel the cycle as
described in the section entitled, "Changing a Cycle while Underway." Then check to make sure that there is water in the mains
and that the tap is turned on. If the problem continues, call for
technical assistance, indicating which light was flashing.
If any of the other indicator lights begin to blink rapidly, turn off
the appliance and call for technical assistance, advising which
lights were flashing.
If, despite all these checks, the dishwasher still does not function
and/or the problem persists, contact the nearest authorised service centre and provide them with the following information:
- the nature of the problem;
- the model number AND
serial number, which are on the plate located
on the side of the inner part of the door.
Never call on unauthorised technicians and refuse to
allow parts to be installed that are not original spare
parts.
.8.
Installation
Installation
Positioning the Appliance
Positioning the appliance in the desired location. The back should
rest against the wall behind it, and the sides, along the adjacent
cabinets or wall. The dishwasher is equipped with water supply
and drain hoses that can be positioned to the right or the left of
the appliance.
Levelling the Appliance
Once the appliance is positioned, adjust the feet (screwing them
in or out) to adjust the level of the dishwasher. The appliance
should not be inclined more than 2˚. If it is level, it will help ensure proper performance.
Cold Water Connection
Connect the cold water supply hose to a threaded 3/4 (gas)
connector, making sure that it is fastened tightly in place (see fig.2).
Some models are fitted with an "Aquastop" water supply hose
(see fig.1) in which the small filter is already housed in the
threaded end.
If the water pipes are new or have not been used for an extended
period of time, let the water run to make sure that the water is
clear and free of impurities. If this precaution is not taken, there
is a risk that the water inlet can get blocked and damage the
appliance.
Hot Water Connection
The water supply to the appliance can also be connected to the
house's hot water line (centralised system, heating system), as
long as it does not exceed a temperature of 60
In this case,the wash cycle time will be shortened by about 15
minutes and the wash efficiency slightly reduced.
The connection must be made to the hot water line following the
same procedures as those for the connection to the cold water
line.
.
the socket immediately. In order to guarantee that the anti-flooding feature operates properly, the "A" box with water supply hose
must be attached to the water supply tap as shown in Fig .1. No
other type of connection is acceptable.
The water supply hose must not, under any circumstances, be cut,
as it contains electrical parts which are live. If the length of the hose
is not adequate to make a proper connection, the hose must be
replaced with one which is long enough. This hose is available upon
request from specialised retailers and service centres.
Drain Hose Connection
Insert the drain hose into a drain pipe with a minimum diameter
of 4cm, Or let it run into the sink, making sure to avoid bending
or crimping it. Use the special plastic support that comes with
the appliance (see fig.3). The free end of the hose must be at a
height between 40 and 100 cm and must not be immersed in
water.
Diagram
fig.3
Attention:
The special plastic hose support must be solidly fastened to the
wall to prevent the drain hose from moving and allowing water to
spill outside the drain.
fig.1
fig.2
Anti-Flooding Protection
The dishwasher is equipped with a system that stops the supply
of water in the event of a problem with the water supply hose, or
leaks within the unit, in order to prevent damage to your home. If
for any reason the box containing the electrical components happens to get damaged, remove the plug for the appliance from
Electrical Connection
After making sure that the voltage and frequency values for the
current in the home correspond to those on the rating plate
(located on the stainless steel inner door of the appliance) and
that the electrical system is correct for the maximum voltage on
the rating plate, insert the plug into an electrical socket which is
earthed properly (the earthing of the appliance is a safety requirement mandated by law).
If the electrical socket to which the appliance must be connected
is not appropriate for the plug, replace the plug, rather than using adaptors or the like as they could cause overheating and
burns.
Caution:
The dishwasher plug must be accessible even when the appliance is installed as a built-in unit so that maintenance can be
done safety.
.9.
.10.
Loading...