1. When you clean the TV set, please
pull out the power plug from AC outlet.
Don't clean the cabinet and the
screen with benzene, petrol and other
chemicals.
2. In order to prolong the using life of
the TV set, please place it in a well
ventilated location.
3. Don't place the
TV set in direct
sunlight or near a
heat source.
4. Do not place the TV set near rain or
moisture as it may cause an electric
shock, or the TV set to catch fire. The
TV set must only
be used in dry in
door locations.
5. The back cover must only be
removed by a registered electrical
service person. Removing the back
cover may result in electric shock, fire
or damage to
the TV set.
6. If the TV set is not going to be used
for a long time, or there is a severe
thunder & Lighting storm, it is
recommended that the TV set be
disconnected from the AC power outlet
and the aerial plug removed.
Explanation on the display tube
Should the picture tube require cleaning, disconnect the power and use a dry
soft cotton cloth. Do not use any cleanser or abrasive cloths.
Installation
Antenna connection
General speaking, to enjoy a clearer picture, we recommend that you use a CATV
system or an outdoor antenna .In different places, the suitable antenna type and position
are different.
300 twin-lead cable
Antenna adapter
(additional purchase)
75 coaxial cable
Plug
(additional purchase)
Note
It is recommended that you'd better use 75
coaxial cable to remove the
Mixer
additional
purchase
Antenna input
75 standard
coaxial type
AC power socket
* the plug type may vary
depending on the model.
disturbance caused by airwave.
Don't bind antenna cable and electric wire together.
Preparation for the remote control
Battery installation
Take off the battery compartment cover. Place two AA batteries, make sure that battery
polarity matches with the +/- mark inside the battery compartment.
Operation notes for the remote control unit
Under normal conditions, the life time of batteries is one year.
If you don't intend to use the unit for a long period or the electricity of the batteries is
used up, remove the batteries to prevent batteries acid from leaking into the battery
compartment.
Never place batteries in a fire.
Avoid dropping the remote control and/or getting it wet.
Position of Buttons and Plug-ins
Front and Side panel
Side AV terminal
VIDEO
L
AUDIO
R
Infrared receiver
Note:
The cabinet and buttons of TV is
only for reference.
Back panel
Antenna input
AVOUT
VIDEO
AUDIO
AV output terminals
AV2 input terminals
VGA input terminal
VGA IN
AV2IN AV 1IN
L
LRLRL
R
AV1 input terminals
YUV
Pb(cb)
Pr(cr)
R
YUV input terminals
TV/Video (input selector
Volume up/ down
+CH -+ VOL -
Channel position up/down
S-video input terminal
Power switch
MENU
Power indicator
TV/AV MENU
S-video input terminal: Special video S-VIDEO AUDIO: L/MONO Track L/MONO ,R Track R
AV output terminals: VIDEO AUDIO L/MONO Track L/MONO ,R Track R
AV2 input terminals MONITOR : VIDEO AUDIO :L/MONO Track L/MONO ,R Track R
AV1 input terminals MONITOR :VIDEO AUDIO :L/MONO Track L/MONO ,R Track R
DVD component terminals:
Interleaved signal Y Cb Cr AUDIO L/MONO Track L/MONO ,R Track R
Progressive signal YPbPr AUDIO L/MONO Track L/MONO ,R Track R
1.When the AV2 terminal, the side AV terminal can not be connected at
the same time .
2.When the side AV is connected, please select the AV 2 terminal.
Function Buttons of the Remote Control
Function buttons of the remote control
SCAN
SHUTTLE
T.SKIP
D.ALBUM
POWER
CALL/HELP
SWAP
S.STD
SOUND
Q.SET
CAL./EXIT
Mute button
To eliminate the sound of the programs
DC standby and power button
TV and AV exchange button
A changeover between TV and other
input signals like AV
Select the 2.1, 3.1 or 5.1 function
Picture still button
Screen call/help button
HDM menu button
Program scan button
select button
Direct
Select a TV channel directly
selection button
Digital
Changeover from one digital, two
digital and three digital
Program swap button
Picture mode selection button
Sound mode selection button
Volume adjustment button
adjustment button
Program
Menu call/select button
Select menu, call and exit
Picture menu call
Sound menu call
Favorite program button
Shuttle(No available)
Function menu call
Q.SET(No available)
Zoom select button
Time skip button(No available)
Time menu call button
Calendar/amusement function exit button
Hotel lock button
Digital album No available
TV/AV
MUTE
HDM
STILL
P.STD
CH+
VOL-VOL+
PICTURE
FUNCTION
TIME
MENU
CH-
FAVORITE
ZOOM
H.LOCK
The Screen Display Menu
For your convenience of operation, here lists the screen display menus of this model
as your reference.
Picture menu
MENU
Picture
Sound
Tune
Setup
Timer
Picture Mode Standard
50
Brightness
Contrast
50
Color
0
Hue
Sharpness
Color Temp. Cool
Advance
50
30
Sound menu
MENU
Picture
Sound
Tune
Setup
Timer
Sound Mode
3D Mono Off
Off
SRS Dialog
Trubass Off
Balance
Equalizer
Tune menuSetup menu
MENU
Picture
Sound
Tune
Setup
Timer
Exchange
Program edit
Search
Auto Search
Quick Search
Timer menu
MENU
Picture
Sound
Tune
Setup
Timer
Current Time
Off Time
On Time
On program
Remind time
Remind program
Sleep Time
122 7
-- --
-- - 10
-- --
---
Off
MENU
Language English
Picture
Screen Saver On
Sound
Curtain
Color Sys. PAL50
Tune
HDM scan 100Hz
Setup
Transparency On
Tilt 0
Timer
H.lock menu
Lock Set
Change Password
New PWD --- Confirm PWD --- Confirm
Lock Off
Channel Lock Off
Standard
0
Note:
When the TV set is powered on, there might be different from what have been
illustrated above. Please do some adjustment as follows to meet your needs.
1. Press the MENU button, and then press CH+/- buttons to select the menu in the
main menu: PICTURE, SOUND, TUNE ,SETUP and TIMER. Of course, you may
select these menus directly by pressing the PICTURE, SOUND, TIME and FUNCTION
buttons on the remote control.
2. If it is not in sub-menu, press the VOL-/+ buttons to enter the sub-menu.
3. Then press the CH+/- to select the desired item, press the VOL-/+buttons to adjust
the numerical value. After that, press the MENU button to return the main menu.
4. If you want to exit the menu, press the MENU button repetitiously.
Switch on/ off the TV set
In the following, the methods of using power switch and remote control to switch on/off
power supply for the TV set will be explained.
Switch on/ off the TV set
Switch on/ off the TV set
1.Connect the power supply wire. Then press the power
switch button, the power indicator will light, in several
seconds the picture will display on the screen.
2. If the TV is in the state of standby, press the POWER
button or the CH+/- buttons on the remote control.
Note:
1. Press the CH+/- buttons which is on the TV set to get
out of the standby state when the remote control is not
in use.
POWER
2. Press the POWER button on the remote control
to the standby mode.
3. Press the power button on the TV set to
completely power off the TV.
4. To eliminate the magnetization completely, the
TV set degausses automatically. There is the
sound of PENG, it is natural.
Automatic stand by function
If no signal has been received, and after five
minutes, it will stand by automatically.
Watching TV Programs
Watching TV programs
How to select the TV program
Select the desired program
1. Use the direct number selection button
Press the button from 0-9 to select a one-figure channel.
If you want to select a double figures channel, press the
figure-selection button and change it into two-figure mode, then
press the number of the channel.
If you want to select a three figures channel, press the figure-selection
button and change it into three-figure mode, then press the number
of the channel.
2. Use the CH+/- buttons
Press the CH+ button to select the channel of the larger number.
CH+
Press the CH- button to select the channel of the smaller number.
VOL-VOL+
VOL-VOL+
VOL-VOL+
MENU
CH-
CH+
MENU
CH-
CH+
MENU
CH-
Select the desired sound
Press the VOL+/- buttons to adjust the volume to your need.
If the colour or sound of a certain channel is
abnormal
If the TV set you bought is
abnormal in colour or sound in a
certain channel, it might be
because the colour or sound
system has been set improperly.
You may follow the instruction
below to adjust it. Press the
MENU button, then press CH+/buttons to select function menu,
and you can see the form . Then
press VOL+ button to enter submenu.
If the colour of the picture is abnormal
Press the CH+/- buttons to move the indicator to "Color Sys.", and
press the VOL+/- buttons to select the proper color.
If the sound is abnormal
Refer the above steps to enter the
Program edit menu. Press the CH+/ buttons to move the indicator to
"Sound Sys.", and press the VOL+/ buttons to select the proper sound.
MENU
Picture
Sound
Tune
Setup
Timer
Language English
Screen Saver On
Curtain
Color sys. PAL50
HDM scan 60Hz
Transparency On
Tilt 0
Program edit
Program NO. 2
Skip Off
Lock Off
Sound Sys. DK
Fine tune <144.20MHz>
Watching TV Programs (continued)
Swap function enables quick swap to the last watched program.
Program swap and auto scan functions
Program swap
1.
Suppose the channel number
you used just now is 8 and the
SWAP
channel number you are using
is 18 (as shown in the figure).
2. If you want to return to the
last watched program channel
8, you can simply press the
SWAP button.
3. If you want to return to
channel 18, press the button
again. Through this function,
you can easily change
between the channel you are
using and the channel you
used last time.
SCAN
CH+
VOL-VOL+
MENU
CH-
Auto program scan
1. Press the SCAN button to
scan through all the memorized
TV channels.
2.When it is the program that
you desired, and press the
MENU button to confirm.
Tune
The TV set has three methods to set the channels, which are Auto search, Search and Fine tune.
In this section, how to use the remote control to set the channel is explained. You can also use the buttons
on the TV set to set channel.
Auto search
Auto search
1. Press the MENU button to display
CH+
VOL-VOL+
MENU
CH-
the menu, then press CH+/-buttons
to select TUNE menu, press VOL+
button to enter.
2. Press the CH+/- buttons to move
the indicator to " Auto Search ".
MENU
Picture
Sound
Tune
Setup
Timer
MENU
Picture
Sound
Tune
Setup
Timer
Exchange
Program edit
Search
Auto Search
Quick Search
Exchange
Program edit
Search
Auto Search
Quick Search
3. Press the VOL+ button, and
"Auto Search" mode will work.
The TV set will search automatically
all available programs, after search
Auto Search
VHF-L 188.16 MHz CH NO:4
is finished, all available programs
will be stored in turn.
If you want to stop the search,
just press the MENU button.
The order of the automatic search is due to the frequency of
the program, generally speaking, it is used only the first time
you search the program, and after the order of the program
has been made, you don't have to use this function,
otherwise the order of the program will be mixed.
After searching (Continued)
Press the CH+/- buttons to check channels.
If the colour or sound is abnormal in a certain channel, it may be
because that the colour or sound system has not been set
properly, then, you may adjust it to proper system (Refer to
page 8).
Loading...
+ 25 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.