1. When you clean the TV set, please
pull out the power plug from AC outlet.
Don't clean the cabinet and the
screen with benzene, petrol and other
chemicals.
2. In order to prolong the using life of
the TV set, please place it in a well
ventilated location.
3. Don't place the
TV set in direct
sunlight or near a
heat source.
4. Do not place the TV set near rain or
moisture as it may cause an electric
shock, or the TV set to catch fire. The
TV set must only
be used in dry in
door locations.
5. The back cover must only be
removed by a registered electrical
service person. Removing the back
cover may result in electric shock, fire
or damage to
the TV set.
6. If the TV set is not going to be used
for a long time, or there is a severe
thunder & Lighting storm, it is
recommended that the TV set be
disconnected from the AC power outlet
and the aerial plug removed.
Explanation on the display tube
Should the picture tube require cleaning, disconnect the power and use a dry
soft cotton cloth. Do not use any cleanser or abrasive cloths.
Installation
Antenna connection
General speaking, to enjoy a clearer picture, we recommend that you use a CATV
system or an outdoor antenna .In different places, the suitable antenna type and position
are different.
300 twin-lead cable
Antenna adapter
(additional purchase)
75 coaxial cable
Plug
(additional purchase)
Note
It is recommended that you'd better use 75
coaxial cable to remove the
Mixer
additional
purchase
Antenna input
75 standard
coaxial type
AC power socket
* the plug type may vary
depending on the model.
disturbance caused by airwave.
Don't bind antenna cable and electric wire together.
Preparation for the remote control
Battery installation
Take off the battery compartment cover. Place two AA batteries, make sure that battery
polarity matches with the +/- mark inside the battery compartment.
Operation notes for the remote control unit
Under normal conditions, the life time of batteries is one year.
If you don't intend to use the unit for a long period or the electricity of the batteries is
used up, remove the batteries to prevent batteries acid from leaking into the battery
compartment.
Never place batteries in a fire.
Avoid dropping the remote control and/or getting it wet.
Position of Buttons and Plug-ins
Front and Side panel
D29FV6 , D34FV6 Model
Channel position up/down
Volume up/ down
MENU
Back panel
D29FV6 Model
VGA input terminal
AV output terminals
Antenna input
TV/Video
Infrared receiver
(input selector
Power indicator
DVI input terminal
DVI IN
Power switch
D34FV6 Model
VGA input terminal
AV output terminals
Side AV terminal
DVI input terminal
Antenna input
DVI IN
S-video input terminal
HDTV input terminals
AV2 input terminals
AV1 input terminals
S-video input terminal
DVD component terminals
HDTV input terminals
AV2 input terminals
AV1 input terminals
DVD component terminals
S-video input terminal: Special video S-VIDEO AUDIO: L/MONO Track L/MONO ,R Track R
AV output terminals: VIDEO AUDIO L/MONO Track L/MONO ,R Track R
AV2 input terminals MONITOR : VIDEO AUDIO :L/MONO Track L/MONO ,R Track R
Av1 input terminals MONITOR :VIDEO AUDIO :L/MONO Track L/MONO ,R Track R
DVD component terminals:
Interleaved signal Y C
b CrAUDIOL/MONO Track L/MONO ,R Track R
Progressive signal YPb PrAUDIOL/MONO Track L/MONO ,R Track R
1.When the S-video terminal and the Video 1 terminals are connected
at the same time, the S-video terminal is preferential.
2.When the side AV is connected, please select the Video 2 terminal.
Function Buttons of the Remote Control
Function buttons of the remote control
Mute button
TV/AV
••••
SNAPSHOT
DVSCAN
CH+
VOL-VOL+
PICTRURE SOUNDTIME FUNCTION
TUNEDIGITAL ZOOMEXIT
MENU
CH-
CALL
SWAP
S.STDP.STD
H.LOCK
To eliminate the sound of the programs
DC standby and power button
TV and AV exchange button
A changeover between TV and other
input signals like AV
I/II select button
DV button
Screen call button
Snapshot button
Program scan button
Direct select button
Select a TV channel directly
Digital selection button
Changeover from one digital, two
digital and three digital
Program swap button
Picture mode selection button
Sound mode selection button
Volume adjustment button
Program adjustment button
Menu call/select button
Select menu, call and exit
(No available)
Hotel lock
(No available)
(No available)
(No available)
(No available)
Picture menu
Function menu
Sound menu
Time menu
Tune menu
Exit /
Calendar
Digital menu
Zoom
The Screen Display Menu
For your convenience of operation, here lists the screen display menus of this model
as your reference.
Picture menu
PIC.
Brightness 50
Contrast 50
Color 50
Sharpness 50
Hue 0
Color Temp. 0
Sound menu
Treble 50
SOU.
Bass 50
Balance 50
Sound Effect
Surround ON
Tuning menu
Prog NO.008
SkipOFF
Sound Sys.B/G
TUN.
Fine Tune
Search
Auto Search
Time menu
TIME
Clock 18:18
On Time --:--
On Prog. ---
Off Time --:--
Sleep 000
Remind Time --:--
Remind Prog. ---
Function menu
Language English
Color Sys. Auto
Prog. Sort
Amusement
FUN.
Special
RGB Sound
Digital menu
Digital Bass On
Digital Scan
DV Play
Comb Filter On
SVM On
DNR Off
DIG.
Current Prog. 2
To Prog. 20
Exchange
H.lock menu
Note:
When the TV set is powered on, there might be
different from what have been illustrated above.
Please do some adjustment as follows to meet your
needs.
1. Press the MENU button to select the menu in
the main menu: PICTURE, SOUND, TUNING,
FUNCTION and DIGITAL. Of course, you may
select these menus directly by pressing the
PICTURE, SOUND, TUNE ,FUNCTION and DIGITAL buttons on the remote control.
2. If you need adjust the numerical value of the TIME and H.LOCK menu, press the
TIME and H.LOCK button on the remote control to call the menu.
3. Press the CH+/- buttons to select the desired item, press the VOL-/+buttons to
adjust the numerical value.
4. If it is in sub-menu, press the VOL+ button to enter the sub-menu. Then press
the CH+/- to select the desired item, press the VOL-/+buttons to adjust the numerical
value. After that, press the MENU button twice to return the main menu.
5. If you want exit the menu, press the MENU button repetitiously or Exit button.
Lock Menu
New PW. ....
Tuning Lock OFF
Preset Prog OFF
Video Lock OFF
Child Lock OFF
Max Volume 100
Unlock
Switch on/ off the TV set
In the following, the methods of using power switch and remote control to switch on/off
power supply for the TV set will be explained.
Switch on/ off the TV set
Switch on/ off the TV set
Power indicator
Channel position up/down
Volume up/ down
MENU
Infrared receiver
Power switch
TV/Video
(input selector
POWER
1.Connect the power supply wire. Then press the power
switch button, the power indicator will light, in several
seconds the picture will display on the screen.
2. If the TV is in the state of standby, press the POWER
button or the CH+/- buttons on the remote control.
Note:
1. Press the P+/- buttons which is on the TV set to get
out of the standby state when the remote control is not
in use.
3
B/G
144MHz
NORMAL
2. Press the POWER button on the remote control
to the standby mode.
3. Press the power button on the TV set to
completely power off the TV.
4. To eliminate the magnetization completely, the
TV set degausses automatically. There is the
sound ofPENG, it is natural.
Automatic stand by function
When the SCREEN SAVER is ON, If no signal has
been received, and after five minutes, it will stand by
automatically. If the SLEEP has been used, the SLEEP
function is priority. When the
the
Automatic stand by function is no available.
When it is AV status, the TV set will enter the screen
saver, after 5 minutes turn to stand by automatically .
SCREEN SAVER is OFF,
Watching TV Programs
Watching TV programs
How to select the TV program
Select the desired program
1. Use the direct number selection button
Press the button from 0-9 to select a one-figure channel.
If you want to select a double figures channel, press the
figure-selection button and change it into two-figure mode, then
press the number of the channel.
If you want to select a three figures channel, press the figure-selection
button and change it into three-figure mode, then press the number
of the channel.
2. Use the CH+/- buttons
Press the CH+ button to select the channel of the larger number.
Press the CH- button to select the channel of the smaller number.
CH+
MENU
VOL-VOL+
CH-
FUNCTION
TIP: When the channel is stored, then the program number
is yellow. When the channel is empty, then the program
number is red.
Select the desired sound
Press the VOL+/- buttons to adjust the volume to your need.
If the colour or sound of a certain channel is
abnormal
If the TV set you bought is
abnormal in colour or sound in a
certain channel, it might be
because the colour or sound
system has been set improperly.
You may follow the instruction
below to adjust it. Press the
FUNCTION button, and you can
see the form .
Language English
Color Sys. Auto
Prog. Sort
Amusement
FUN.
Special
RGB Sound
CH+
VOL-VOL+
MENU
CH-
If the colour of the picture is abnormal
Press the CH+/- buttons to move the indicator to "Color Sys.", and
press the VOL+/- buttons to select the proper colour.
If the sound is abnormal
Press the CH+/- buttons to move
the indicator to "
press the VOL+/- buttons to select
the proper sound. (If the TV set you
bought had multi-system, then
M, B/G and I
Sound Sys.", and
D/K,
will appear alternately.)
Prog NO.008
SkipOFF
Sound Sys.B/G
TUN.
Fine Tune
Search
Auto Search
Watching TV Programs (continued)
Swap function enables quick swap to the last watched program.
Auto scan function enables automatic successive scanning of the programs in memory
with(There are 12 pictures display on the screen at the same time)."OFF" skip status
Program swap and auto scan functions
Program swap
SWAP
1. Suppose the channel number
you used just now is 8 and the
channel number you are using
is 18 (as shown in the figure).
2. If you want to return to the
last watched program channel
8, you can simply press the
SWAP button.
3. If you want to return to
channel 18, press the button
again. Through this function,
you can easily change
between the channel you are
using and the channel you
used last time.
8
B/G
144MHz
NORMAL
18
B/G
144MHz
NORMAL
18
B/G
144MHz
NORMAL
SCAN
CH+
MENU
VOL-VOL+
CH-
Auto program scan
1. Press the SCAN button to
scan through all the memorized
TV channels. The TV set screen
displays 12 pictures at the same
time. Press the S.STD button to
scan next page, and press the
P.STD to scan last page.
2.Press the CH+/- buttons and
VOL-/+ buttons to select the
program that you desired, and
press the MENU button to
confirm.
Tuning
The TV set has three methods to set the channels, which are Auto search, Search and Fine tune.
In this section, how to use the remote control to set the channel is explained. You can also use the buttons
on the TV set to set channel.
Auto Search
FUNCTION
CH+
MENU
VOL-VOL+
CH-
TUNE
Select the search mode
1. Press the FUNCTION button, the
function menu will appear on the
screen.
2. Press the CH+/- buttons to move
the indicator to "Special ", then
press the VOL+ button to sub-menu.
. Press the CH+/- buttons to move
the indicator to " ",
then press the VOL+ button to
select the desired auto search mode.
Auto search
1. Press the TUNE button, the tuning
menu will appear on the screen.
( For example, the auto search mode I.)
2. Press the CH+/- buttons to move
the indicator to " Auto Search " .
Language English
Color Sys. Auto
Prog. Sort
Amusement
FUN.
Special
RGB Sound
Prog NO.008
SkipOFF
Sound Sys.B/G
TUN.
Fine Tune
Search
Auto Search
Search Mode Ordinal
Curtain Mode Off
Screen Saver Off
Tilt 0
CH+
VOL-VOL+
MENU
CH-
3. Press the VOL+ button, and
"Auto Search" mode I will work.
The TV set will search
automatically all available programs,
after search is finished, all available
Prog NO.008
SkipOFF
Sound Sys.B/G
TUN.
Fine Tune
Search
Auto Search
AutoSearch Natrual 001
125.00MHz
programs will be stored in turn.
If you want to stop the search,
just press the MENU button.
The order of the automatic search is due to the frequency of
the program, generally speaking, it is used only the first time
you search the program, and after the order of the program
has been made, you don't have to use this function,
otherwise the order of the program will be mixed.
TIP: To eliminate the reorder for misapplying, you can set the
"Tuning Lock" of the Lock Menu to ON the order of the
after
program. (Refer to the page 33)
Tuning (Continued)
Search
After searching (Continued)
Press the CH+/- buttons to check channels.
CH+
MENU
VOL-VOL+
CH-
TUNE
CH+
MENU
VOL-VOL+
CH-
CH+
If the colour or sound is abnormal in a certain channel, it may be
because that the colour or sound system has not been set
properly, then, you may adjust it to proper system (Refer to
page 8).
Search
1. Press the CH+/- buttons or Direct
select button to select the desired
channel number.
2. Press the TUNE button, the tuning
menu will appear on the screen.
( For example, the auto search mode I.)
. Press the CH+/- buttons to
move the indicator to "Search".
Prog NO.008
SkipOFF
Sound Sys.B/G
TUN.
Fine Tune
Search
Auto Search
1
B/G
144MHz
NORMAL
MENU
VOL-VOL+
CH-
CALL
4. Press the VOL+ or VOL- buttons,
the TV set will begin to search up or
down, when the TV set has searched
a program, the TV set will stop
searching. If the program is not the
one you need, you can press the
button again, let the TV set continue
Prog NO.008
SkipOFF
Sound Sys.B/G
TUN.
Fine Tune
Search
Auto Search
Search 001
125.00MHz
to search until it has searched the TV
signal you need.
Note:
Usually, five seconds after the channel has been changed, the channel
number will disappear automatically. If you want to know which channel
you are watching, just press the CALL button once.
Tuning (Continued)
Fine Tune
Fine Tune
If the picture and/or sound are poor, try using the FINE
TUNE feature. Do not use this feature unless reception
is poor.
CH+
MENU
VOL-VOL+
CH-
TUNE
CH+
MENU
VOL-VOL+
CH-
1. Press the CH+/- buttons or Direct
select button to select the desired
channel number. ( For example, the
channel 1.)
2. Press the TUNE button, the tuning
menu will appear on the screen.
3. Press the CH+/- buttons to
move the indicator to " Fine Tune ".
4. Press the VOL+ button to enter
the Fine Tune Menu, and then
VOL- button to search downwards
or the VOL+ button to search
upwards
until it has searched the
TV signal you need.
the
TUN.
Prog NO.008
SkipOFF
Sound Sys.B/G
TUN.
Fine Tune
Search
Auto Search
1
B/G
144MHz
NORMAL
Prog NO.008
SkipOFF
Sound Sys.B/G
Fine Tune
Search
Auto Search
Fine Tune 001
125.00MHz
Loading...
+ 28 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.