SPLIT TYPE ROOM AIR CONDITIONER
OPERATION MANUAL
AS09TACHRA
AS12TBCHRA
AS18TCCHRA
AS24TECHRA
AS26TACHRA
AS35TBCHRA
AS53TCCHRA
AS71TECHRA
Contents
PARTS AND FUNCTIONS
OPERATION
MAINTENANCE
CAUTIONS
TROUBLE SHOOTING
Please read this operation manual before using the air conditioner.
Keep this operation manual for future reference.
0011511007
1
2
5
6
7
条形码绘制区
Parts and Functions
Indoor Unit
Inlet
1
1
Inlet grille
2
2
Outlet
3
3
Anion generator
4
5
7
(adjust up and down air flow
Don't adjust it manually)
(inside)
Horizontal flap
Vertical blade
6
6
(adjust left and
ight air fl
r
Display board
Power indicator
1
(Lights up when unit starts.)
2
Timer mode indicator
(Lights up whenTimer operation is selected.)
Operation mode indicator
3
Remote signal receiver
4
(A beeping sound is generated when a signal from remote controller isreceived.)
Actual inlet grille may vary from the one shown in the
manual according to the product purchased
Outdoor Unit
4
Air Purifying Filter
5
4
(lights up when the compressor is on.)
(inside)
ow)
Display board
OUTLET
INLET
CONNECTING PIPING
AND ELECTRICAL WIRING
DRAIN HOSE
4
8
Emergency
Switch
Remote controller
1
2
3
4
5
9
10
11
12
13
14
15
16
17
1. Mode display
Operation mode
Remote controller
AUTO
COOL DRY
2. Signal sending display
3. SWING display
4. FAN SPEED display
LO MED HI
5. LOCK display
6. TIMER OFF display
TIMER ON display
7. TEMP display
NOTE:
Cooling only unit do not have displays and functions related with heating
If the unit which you purchased has healthy function,follow it.If not,please ignore.
Loading of the battery
FAN
HEAT
Display
circulated
AUTO
6
7
Additional functions display
8.
SLEEP
Operation mode
Remote controller
HEALTH
QUIET TURBO
9. QUIET button
10. HEAT button
11. COOL button
8
12. AUTO button
18
13. FAN SPEED button
14. TIMER button
19
15. SELF CLEAN button
16. LOCK button
20
Used to lock buttons and LCD display
21
17. LIGHT button
Control the lightening and
extinguishing of the indoor LED
22
display board.
23
18. POWER ON/OFF button
24
19. DRY button
20. TEMP button
25
21. SWING button
22. HOUR button
23. EXTRA FUNCTION button
Function: Sleeping---- Healthy
airflow position1--- Healthy airflow
position 2 --- Power ---
--- A-B yard---
HEALTH
24.CANCEL/CONFIRM button
Function: Setting and cancel to the
timer and other additional functions.
25. RESET button
When the remote controller appears
abnormal, use a sharp pointed
article to press this button to reset
the remote.
Air
sending
Remove the battery cover;
1
Load the batteries as illustrated.
2
2 R-03 batteries, resetting key
(cylinder);
Be sure that the loading
3
is in line with th
Load the battery,then put on the cover again.
4
Note:
The distance between the signal transmission head and the receiver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change- over
type fluorescent lamp or
room, the recei
so the distance to the indoor unit should be shorter.
Full display or unclear display during operation indicates the
ries have been used up.
batte
If the remote controller can't run normally during operation, please
remove the batteries and
ver is apt to be disturbed in receiving
wireless telephone is installed in the
Please change batteries.
reload several minutes later.
e" + "/"-";
the signals,
1
Operation
Unit start / stop
Remote controller
2
1. Unit start
Press ON/OFF on the remote controller, unit starts.
2.Select temp.setting
Press
/
Every time the button is pressed, temp.setting
increase 1
rapidly
Every time the button is pressed, temp.setting
decrease 1
decrease rapidly
Select a desired temperature.
button
o
C,if kept depressed, it will increase
o
C,if kept depressed, it will
3.Fan speed selection
Press FAN button. For each press, fan speed
changes as follows:
Remote controller:
nothing
MED HI
Remote
Controller
Under the mode of auto operation, air conditioner will
automatically select Cool or Heat operation according
to room temperature.
air conditioner
according to room
Cooling only unit do not have displays and functions
related with heating
In DRY mode, when room temperature becomes
lower than temp.setting+2
at LOW speed regardless of FAN setting.
In HEAT mode,warm air will blow out after a short
periodof the time due to cold-draft prevention function.
In FAN operation mode, the unit will not operate in
COOL or HEAT mode but only in FAN mode ,AUTO is
not available in FAN mode.And temp.setting is disabled.
When FAN is set to AUTO, the air conditioner automatically
adjusts the fan speed according to room temperature.
In FAN mode,SLEEP operation is not available.
automatically adjusts the fan speed
LOW
Air conditioner is running under displayed fan speed.
When FAN is set to AUTO, the air conditioner
automatically adjusts the fan speed according to room
temperature.
Operation
Mode
AUTO
COOL
HEAT
FAN
Display Board
DRY
1
3
2
Display
circulated
AUTO
Note
When FAN is set to AUTO, the
temperature.
o
C,unit will run intermittently
Air Flow Direction Adjustment
1.Vertical flap
Pos.1
Pos.2
Pos.3
Pos.4
(Autoswing)
Pos.5
2.Press button. changes as follows: Pos.4
Press button again ,
present position,
3.Press
the swing function will be cancelled
button to choose the Pos.2 and Pos.3.
Cautions:
When adjusting the flap by hand,turn off the unit.
When humidity is high,condensate water might occur
at air outlet if all vertical louvers are
right.
It is advisable not to keep horizontal flap at downward
position for a long time in COOLor DRY
otherwise, condensate water might occur.
Note:
When restart after remote turning off, the remote
controller will automatically
set swing position.
DRED Operation
(This function is unavailable on some models.)
Haier Peaksmart enabled air-conditioners have a Demand
Response Mode display on the indoor unit.
The display could be labelled d1, d2, d3 (wording may
differ model to model).
These modes are described in more detail below:
Your air-conditioner will continue
to cool or heat during the peak
DRM3 d3
DRM2 d2
DRM1 d1
demand event. The energy
consumed by your air-conditioner
is capped to 75%.
Your air-conditioner will continue
to cool or heat during the peak
demand event. The energy
consumed by your air-conditioner
is capped to 50%.
Your air-conditioner is still turned
on and the fan will continue to
operate. Your compressor is
turned off and cool/hot air will no
longer be generated
Remote controller
COOL/DRY/AUTO(Initial state):
HEAT(Initial state):
(no)
vertical flap will stop over
adjusted to left or
mode ,
return to the previous
odottahWnoitpircseDyalpsiDedoM
No action is required.
No action is required.
DRM1 mode is only activated during
emergency demand management
situations. This mode will automatically reset
the device within 2 hours .If your air-con is in
this mode for longer than 2 hours please
contact Energex on 13 12 53.
2
Operation
Timer On/Off On-Off Operation
1.After unit starts, select your desired operation mode.
2.Press TIMER button to change TIMER mode. Every
time the button is pressed, display changes as follows:
Remote controller:
0.5h
TIMER ON TIMER OFF TIMER ON-OFF
0.5h 0.5h
0.5h
TIMER OFF-ON
Then select your desired TIMER mode (TIMER ON or
TIMER OFF or TIMER ON-OFF). " "or " "will flash.
3.Press / button to set time.
Press the button for each time, setting time in the first
12 hours increased by 0.5 hour every time, after 12
hours,increased by 1 hour every time.
Press the button for each time, settiing time in the first
12 hours decreased by 0.5 hour every time, after 12
hours,decreased by 1 hour every time.
It can be adjusted within 24 hours.
4.Confirm timer setting
After adjust the time,press button and confirm the
time ON or OFF button will not flash any more.
BLANK
POWER/SOFT Operation
(This function is unavailable on some models.)
(1)
POWER Operation
When you need rapid heating or cooling, you can use this function.
Press button to enter additional options, when cycle
display to , will flash，and then press ,enter to
power function. When cancel the function, please enter
additional options again and to cancel power function.
(2)
QUIET Operation
You can use this function when silence is needed for rest or reading.
Press QUIET button, the remote controller will show ,
and then achieve to the quiet function. Press again this
QUIET button , the quiet function will be cancelled.
Note ：
During POWER operation, in rapid COOL mode ,
will show inhomogeneous temperature distribution.
Long period QUIET operation will cause effect of not too
cool or not too warm.
the room
5.Cancel timer setting
Press the button by times until the time display
eliminated.
Hints:
After replacing batteries or a power failure happens, time
setting should be reset.
According to the Time setting sequence of TIMER ON or
TIMER OFF, either Start-Stop or Stop-Start can be achieved.
Self Clean Operation
◆Functional description: the purpose of this function is to
clean the evaporator.
Entry and exit Press self clean button to enter this
function, then it will display "CL" on the panel of the indoor
unit and also on the remote controller. After running 20-30
minutes, this function will exit automatically when the " Pi "
sound is heard twice, then the unit returns to original state.
Under operation process of self clean, pressing the button
repeatedly has no effect and the function will not exit, but
pressing the power off button and other mode button can
make it exit.
Emergency operation and test operation
Emergency Operation:
Use this operation only when the remote controller
is defective or lost.
When the emergency operation switch is
pressed,the" Pi "sound is heard once, which means
the start of this operation.
In this operation, the system automatically selects
the operation modes,cooling or fan or heat,according
to the room temperature.
O
O
FAN
C
C
Timer
mode
NO
NO
Designated
temperature
O
C
26
AUTOMATIC
AUTOMATIC
Room
temperature
ABOVE 23
BELOW 23
(Cooling only uint）
Room temperature
It is not possible to operate in dry mode.
O
C
O
C
BELOW 23
Operation
mode
COOLING
HEAT
O
C
Designated
temperature
26
23
Operation
mode
Air flow
Timer
mode
NO
Pi
Air flow
AUTOMATIC
Test operation:
Test operation switch is the same as emergency switch.
Use this switch in the test operation when the room temperature is below
16 ℃, do not use it in the normal operation.
Continue to press the test operation switch for more
than 5 seconds. After you hear the “Pi” sound twice,
release your finger from the switch: the cooling
operation starts with the air flow speed “Hi”.
After 30 minutes, test operation ends automatically.
Pi Pi
3
Operation
Comfortable SLEEP
Press button to enter additional options, when
cycle display to , will flash. And then press
enter to sleep function.
Operation Mode
1. In COOL,DRY mode
1 hour after SLEEP mode starts,temp will become
O
higher than temp setting. After another 1 hour,
C
1
temp risesby 1 futher
6 hours then stops Temp is higher than temp setting
so that room temperature won’t be too low for your
sleep.
O
C
SLEEP operation starts SLEEP operation stops
.The unit will run for further
Approx.6hrs
5. When comfortable sleeping function is set to 8 hours the
comfortable sleeping time can not be adjusted.When TIMER
function is set,the comfortable sleeping function can't be set
up. After the sleeping function is set up,if user resets
TIMER function, the sleeping function will be cancelled; the
machine will be in the state of timing-on,if the two
are set up at the same time,
either of their operation time is
modes
ended first, the unit will stop automatically,and the other
mode will be cancelled.
Note
When TIMER function is set, the sleeping function can’t be
set up .After the sleeping function is set up,if user resets
TIMER function, the sleeping function will be cancelled; the
machine will be in the state of timing-on.
Power Failure Resume Function
If the unit is started for the first time, the compressor will not
start running unless 3 minutes have elapsed. When the power
resumes after power failure, the unit will run automatically,
and 3 minutes later the compressor starts running.
Healthy airflow Operation
1.Press to starting
Setting the comfort work conditions.
2.The setting of healthy airflow function
O
C
Rises 1
Rises 1
O
C
Unit stop
1 hr
1 hr
Temp.setting
In COOL, DRY mode
2.In HEAT mode
1 hour after SLEEP mode starts, temp will become
O
2 C lower than temp setting. After another 1 hour,
temp decrease by 2 C further. After more another
3 hours, temp rises by 1 C further.The unit will run
O
O
for further 3 hours then stops.Temp is lower than
temp setting so that room temperature won't be too
high for your sleep.
Temp.setting
1 hr
Decreases 2
1 hr
Decreases 2
Unit stop
O
C
O
C
3 hrs
3 hrs
SLEEP
operation starts
Rises 1OC
SLEEP
operation stops
In HEAT mode
3.In AUTO mode
The unit operates in corresponding sleep mode
corresponding sleep mode adapted to the
automatically selected operation mode.
4. In FAN mode
It has no SLEEP function.
Press button to enter additional options,Press this
button continuously, the louvers location will cycle between
in the following three locations, to choose the swing location
what you needed,and then press button to confirm.
Healthy
airflow
upwarder
Healthy
airflow
downwarder
Present
position
3.The cancel of the healthy airflow function
Press button to enter additional options,Press this
button continuously, the louvers location will cycle between
in the following three locations again,and then press
button to cancel.
Notice: Do not direct the flap by hand. Otherwise, the
grille will run incorrectly. If the grille is not run correctly, stop
for a minute and then start, adjusting by remote
controller.
Note:
1.After setting the healthy airflow function, the position
grill is fixed.
2.In cooling, it is better to select the
3.In cooling and dry, using the air conditioner for a long
time under the high air humidity, condensate water may
occur at the grille .
mode.
4
Maintenance
For Smart Use of The Air Conditioner
Setting of proper room
temperature
Proper
temperature
Close doors and windows
during operation
During cooling operation
prevent the penetration of
direct sunlight with
curtain or blind
If the unit is not to be used
for a long time, turn off the
power supply main switch.
OFF
Do not block the air inlet
or outlet
Use the timer effectively
Use the louvers effectively
Remote Controller
Do not use water ,wipe the controller with a
dry cloth.Do not use glass cleaner or chemical
cloth.
Do not use the following for cleaning
Gasoline,benzine, thinner or cleanser may
damage the coating of the unit.
Air Filter cleaning
Open the inlet grille by pulling it upward.
Remove the filter.
Push up the filter's center tab slightly until it is released
from the stopper, and remove the filter downward.
Clean the filter.
Use a vacuum cleaner to remove dust, or wash the filter with
water.After washing, dry the filter completely in the shade.
Attach the filter.
Attach the filter correctly so that the "FRONT" indication is
facing to the front.Make sure that the filter is completely
fixed behind the stopper.If the right and left filters are not
attached correctly, that may cause defects.
Close the inlet grille.
Indoor Body
Wipe the air conditioner by using a soft and
dry cloth.For serious stains,use a neutral
detergent diluted with water.Wring the water
out of the cloth before wiping.then wipe off
the detergent completely.
O
Hot water over 40
discoloring or deformation.
C(104OF) may cause
Once every
two weeks
Replacement of Air Purifying Filter
1.Open the lnlet Grille
Prop up the inlet grille by using a
small device named grille-support
which located in the right side of
the indoor unit.
2.Detach the standard air filter
Slide the knob slightly upward to
release the filter, then withdraw it.
Detach old Air Purifying Filter
3.Attach Air Purifying Filter
Put air purifying filter appliances into the
right and left filter frames.
(NOTE: Air purifying filter is optional part)
4.Attach the standard air filter
(Necessary installation)
ATTENTION:
The white side of the photocatalyst air purifying
filter face outside,
The green side of the bacteria-killing medium air
purifying filter face outside,
5.Close the Inlet Grille
Close the Grille surely
NOTE:
The photocatalyst air purifying filter will be solarized in fixed
time. In normal family,
The bacteria-killing medium air purifying filter will be used
for a long time,no need for replacement. But in the period
of using them ,you should remove the dust frequently by
using vacuum cleaner or flaping them lightly,otherwise ,
its performance will be affected.
and the black side face the unit.
and the white side face the unit.
it will be solarized every 6 months.
Please keep the bacteria-killing medium air purifying filter in
the cool and dry conditions
when you stop using it,or its ability of sterilization will
avoid long time directly sunshine
be
reduced.
5
Cautions
WARNING
Please call Sales/Service Shop for the Installation.
Do not attempt to install the air conditioner by yourself because improper works
may cause electric shock, fire, water leakage.
WARNING
When abnormality such as burnt-small found,
immediately stop the operation button and
contact sales shop.
Use an exclusive
power source
with a circuit
breaker
Check proper
installation of the
drainage securely
OFF
Connect power supply cord
to the outlet completely
STRICT
ENFORCEMENT
Do not use power supply
cord in a bundle.
PROHIBITION
Do not start or stop the
operation by disconnecting
the power supply cord
and so on.
PROHIBITION
STRICT
ENFORCEMENT
Use the proper voltage
STRICT
ENFORCEMENT
Take care not to damage
the power supply cord.
PROHIBITION
Do not channel the air flow directly
at people, especially at infants or
the aged.
PROHIBITION
STRICT
ENFORCEMENT
1.Do not use power supply cord extended
or connected in halfway
2.
Do not install in the place where there is any
possibility of inflammable gas leakage around the unit.
3.Do not get the unit exposed
to vapor or oil steam.
PROHIBITION
Do not insert objects into the air
inlet or outlet.
PROHIBITION
Do not try to repair or
reconstruct by yourself.
Connect the earth
cable.
earthing
Do not use for the purpose of storage of
food, art work, precise equipment,
breeding, or cultivation.
PROHIBITION
Do not install the unit near a fireplace
or other heating apparatus.
PROHIBITION
Do not place animals or plants in
the direct path of the air flow
PROHIBITION
CAUTION
Take fresh air occasionally especially
when gas appliance is running at the
same time.
STRICT
ENFORCEMENT
Check good condition of the
installation stand
PROHIBITION
Do not place any objects on or
climb on the unit.
PROHIBITION
Do not operate the switch with
wet hand.
PROHIBITION
Do not pour water onto the unit
for cleaning
PROHIBITION
Do not place flower vase or water
containers on the top of the unit.
PROHIBITION
6
Trouble shooting
Cautions
Before asking for service, check the following
first.
Cause or check points
When unit is stopped, it won't restart
immediately until 3 minutes have
elapsed to protect the system.
When the electric plug is pulled out
and reinserted, the protection circuit
will work for 3 minutes to protect the
air conditioner.
During unit operation or at stop,
a swishing or gurgling noise may
be heard.At first 2-3 minutes after
unit start, this noise is more noticeable.
(This noise is generated by
refrigerant flowing in the system.)
During unit operation, a cracking
noise may be heard.This noise is
generated by the casing expanding
or shrinking because of
temperature changes.
Should there be a big noise from
air flow in unit operation, air
filter may be too dirty.
This is because the system
circulates smells from the interior
air such as the smell of furniture,
paint, cigarettes.
During COOL or DRY operation,
indoor unit may blow out mist.
This is due to the sudden cooling
of indoor air.
In DRY mode, when room temperature
becomes lower than temp.
setting+2
intermittently at LOW speed
regardless of FAN setting.
Is power plug inserted?
Is there a power failure?
Is fuse blownout?
o
C,unit will run
Is the air filter dirty?
Normally it should be cleaned
every 15 days.
Are there any obstacles before
inlet and outlet?
Is temperature set correctly?
Are there some doors or
windows left open?
Is there any direct sunlight
through the window during the
cooling operation?(Use curtain)
Are there too much heat sources
or too many people in the room
during cooling operation?
Normal
Performance
inspection
Multiple
check
Phenomenon
The system
does not restart
immediately.
Noise is heard
Smells are
generated.
Mist or steam are
blown out.
In dry mode,
fan
speed can’t be
changed.
Poor cooling
Do not obstruct or cover the ventilation
conditoner.Do not put fingers
inlet/outlet and
This appliance is not intended for use by persons (including children)
with reduced physiced, sensory or mental capabilities or lack of
experience and knowledge, unless they have been given supervision
or instruction concerning use of appliance by person responsible for
their safety. Children should be supervised to ensure that they do not
play with the appliance.
swing louver.
or any other things into the
grille of the air
Specifications
The refrigerating circuit is leak-proo f.
The machine is adaptive in following
1.Applicable ambient temperature range:
Indoor
Cooling
Outdoor
Indoor
Heating
Outdoor
Outdoor
(INVERTER)
2. If the power supply cord is damaged, it
manufacturer
3. If the fuse of indoor unit on PC board is
it with the type of
broken,change it with the type of
4. The wiring method should be in line with
5. After installation, the power plug should
6. The waste battery should be disposed
7. The appliance is not intended for use
persons
8.Young children should be supervised
the appliance.
with
9. Please employ the proper power plug,
cord.
The power plug and connecting cable
10.
attestation.
11.In order to protect the units,please turn
30 seconds
or its service agent or a similar
without supervision.
later, cutting off the power.
Maximum:D.B/W.B
Minimum:D.B/W.B
Maximum:D.B/W.B
Minimum:
Maximum:D.B
Minimum:
Maximum:D.B/W.B
Minimum:D.B
Maximum:D.B/W.B
Minimum:D.B
T. 3.15A/ 250V
D.B
D.B
. If the fuse of
T.25A/250V
situation
32oC/23oC
o
21
C/15oC
o
C/26oC
46
o
-10
C
o
C
27
o
15
C
o
C/18oC
24
o
-10
C
o
C/18oC
24
o
C
-15
must be replaced
qualified
broken,please
properly.
by young children or
to ensure that th
which fit into the
off the A/C first,
outdoor
the local wiring
be easily reached.
must have
acquired the local
by the
person.
change
unit is
standard.
infirm
ey
do not play
p
ower supply
and at least
7
Loading...