Haier YR-E06, YR-H71, AD142FCBHA, AD182FCBHA Operation Manual

No. 0010573682

C

Table of Contents

Operation

5-9

Parts and Functions

1-4

11

10

Use shielede wires for telecommunication
between wire controller and indoor unit;
indoor unit and outdoor unit. Ground the
shield on one side.
Otherwise misoperation because of noise
may occur.
Signal wire is self-provided by user.

Shielded wire

ground

OPERATION MANUAL

YR-E06&YR-H71

Please read this operation manual before using the air conditioner.
Please keep this manual carefully and safely.

Health Function and Installating the Reciever

Installating the

wire controller

11

Installating the

wire controller

5. Replace the upper cover of wire controller

Note

Try as far as possible a flat surface for installation.
Don't use excessive force when tightening screws,
or lower part might got deformed.

Hint

1. Power supply switch and signal wire should be prepaired by the user.

2. Don't touch PCB with hand.

Be careful not to hold down the wiring.

1. Remove upper cover of wire controller

Remove upper part of wire controller by press.

Lower cover of wire
controller

Upper cover of wire
controller

2. Install the wired remote controller

Please drill two holes on the wall according to the
back cover screw hole position of the wire remote
controller, then strike the wood block to the holes
respectively, then align the 2 screw hole of the wire
controller back cover to the wood block, fasten the
wire reote controller to the wall use wood screws.

3. Switch setting

The switchs setting as follows:1.ON 2.OFF 3.ON 4.OFF

4. Connecting method as the following chart

Back cover of the wire
controller

PCB is mounted on lower part of wire
controller, be careful not to damage it.

Switch button

Screw hole

No

Symbol

colour

contents

1

2

3

4

A

B

C

D

White or Green

Red

Yellow

COM

Gnd

12V

Remote controlller

Wire remote controlller

Remote controlller is an accessory, to be ordered extrally

Remote controlller

Remote receiver

Installation of receive display
Because of the temperature sensitive device, do not install the receive display at straight sunlight place,
either in front of air outlet grill, for it is effected greatly from cool air and heat air, the receive display is
at least 20mm distance to the air outlet grill.
Since there is light sensitive device which receives wireless remote signal, so do not installed behind the
window curtain or other obstacles, in order not to obstruct the signal.
Must fix the remote control wire far from strong electricity (such as the wiring of electric light, air cond­itioner, etc.) and weak electricity (such as the wiring of telephone, interphone, etc.).

2.Place the panel onto the fixed frame, pay attention
that the four claws must be placed into the
corresponding four poles on the frame

1.Fix the receive display with screws
on the selected place

C

C

1

3

4

5

2

OFF

RESET

LOCK

SLEEP

FAN

TEMP

ON

OFF

SWING

MODE

CLOCK

CODE

LIGHT

OFF

A
U
T
O

RESET

LOCK

SLEEP

FAN

TEMP

ON

OFF

SWING

MODE

CLOCK

CODE

LIGHT

OFF

A
U
T
O

CLOCK

RESET

LOCK

SLEEP

FAN

TEMP

ON
OFF

SWING

MODE

CODE

LIGHT

OFF

A
U
T
O

1

fig(1)

Left picture is a wired remote controller,
which can be used on

Series

wired control
units ,The remote controller can be purchased
extrally.
Wired remote Controller using method:

1.Use one wired remote controller. See fig (1)

2.Also can buy a remote controller extrally, realize
wired remote control + remote control dual control modes.

3.When the remote controller can be used on series wired
remote controller units ,than please press the botton
"CODE"to choose the program of code "A"

4.Series wired remote control units have power

failure

compensation.

The right figure is a remote controller, which can be used on

series

remote control units and the matching remote control receiver

1.Remote control receiver using method :
Use remote controller control the
remote control window of the remote
control receiver.

2.

Series

remote
controller units
please press the
botton "CODE"to choose
the program of code "B"

3.

Series

remote control units
have not power

failure compensation.

fig(2)

FRESH

HIGH/SO

TIMER

SET

FILTER

B

A

M D

HEALTH

FRESH

HIGH/SO

TIMER

SET

FILTER

B

A

M D

HEALTH

Parts and Functions

HEAT

HEAT

HEAT

HEAT

SET

ROOM

MODE

FAN

TEMP

CLOCK SET

TIMER SLEEP

RESET

FILTER RESET

HEALTH

SWING

C

ON

OFF

*

AUTO

ON/OFF

SET

ROOM

MODE

FAN

TEMP

CLOCK SET

TIMER SLEEP

RESET

FILTER RESET

HEALTH

SWING

C

ON

OFF

*

AUTO

ON/OFF

10

Health Function and Installating the Reciever

Connecting wiring method of receiver :

Refer the indoor unit wiring diagram .
Safety cautions see the electrical wiring part .

1.How to use the health function (only for units with this function)
After set the right function mode, press health button,
remote controller or wire controller displays " ",oxygen pump
or negative ion generator starts up to apply oxygen or negative
ion to indoor unit. Press the button again,the sign " " disapp­ eared and negative ion generator stops working. After all health
function of the indoor unit being fully canceled, oxygen pump
stopped.

On the "Health" mode, if you want
to setting timing open mode, should
close the health first: On the timing
open mode, please don't use health
function.

About health function

CAUTION:
When the temperature of the outdoor unit is lower than 4 ,
oxygen pump is automatically stopped, if press health button
just then, oxygen pump could not start up. But if the air condi­tioner has the negative ion function simultaneous,when press
the Health button, negative ion function could still be operated.
When the temperature of the outdoor unit is higher than 6 ,
oxygen pump could automatically resume to oxygen-make
function.

1 .Emergency switch
2 .Running lamp: When the compressor working, this lamp bright.
3 .Timing lamp: When the unit been setting Timing running, this lamp bright.
4 .Power lamp: After open the unit, this lamp bright when the unite enter
health running, the lamp change from orange to blue lamp.
5 .Indoor temp. sensor: Test the room temperature.

FRESH

HIGH/SO

TIMER

SET

FILTER

HEALTH

MODE

FAN

HEALTH

TEMP

CLOCK SET

TIMER SLEEP

RESET

ON/OFF

AM

SET

AM

SWING

FILTER RESET

HEAT

HEAT

Concerning MRV Auto Restart function for H-MRV models

Haier Auto Restart function when the unit power drops down suddenly, the unit microprocessor
will store the previous working condition and when the power is on again, the unit will run as this
memory.
Auto Restart function is designed basically on the MRV whole system, but it is suitable for each
indoor unit individually.
If some of indoor units power cut down, but the outdoor unit and the other
indoor units still work, maybe problems will happen such as freezing at cooling mode and overload
protection at heating mode on those indoor units without power.

Reason

When one or some indoor units power drops down and the other indoor units are still work, the
indoor units without the power, will keep the previous working condition before the power is off.
And expansion valve keeps open at a kind of opening rate condition as the previous requirement,
so there is refrigerant flowing in the exchanger, but the indoor fan stops working. If the units work
at cooling mode, the indoor units without the power will maybe make freezing. If the unit works
at heating mode, maybe the outdoor unit compressor will stop because of the pressure or temperature
protection. This is our design basically on Auto Restart function currently.

Haier, Herewith, solemnly informs our customers, installers, distributors, etc. when making installation,

please make sure when the power is shut down whether artificially or accidentally, the whole system
including outdoor unit and all the indoor units must be off. If you do not make the installation as
our indication, Haier will not be responsible for any problem resulting from this.

User Caution

Used to select Auxiliary
electric heater.

9

About the remote cnotrol operation, above only take wired remote controller and remote controller
as a example about the remote controller and remote receiver use method, it is the same remote co­ntroller , please use refer to above method.
No sleep function when use remote and remote receiver.

Operation

NOTE:In function of code B ,set and cancel Auto restart function by using of "SWING" button.

Auto restart (to be applied for a necessary situation)

:

Setting Method: When the wire remote controller is on (excluding timer mode and fan mode), press
the "Sleep" button on the wire remote controller 10 times within 5 seconds, and after the buzzer
rings 4 times, the air conditioner will enter the state of power failure compensation.

Cancel Method: Press the "Sleep" button on the wire remote controller 10 times within 5 seconds,
and after the buzzer rings 2 timer, the Auto restart mode will be cancelled.

Notes: When a power failure suddenly occurs during the air conditioner is working after the Auto restart
is set, if the air conditioner will not be used for a long time, please cut off the
power supply to prevent its operation from being resumed after the power is supplied again, or press
the "Switch On/Off" button after the power comes again.If the controller no sleep key ,use the "swing"
key instead the "sleeping" on setting the auto restart function.

After the Auto restart is set, if power failure suddenly occurs while the air conditioner is
working, it will resume the previous working state when the power is supplied again.

Used to adjust the time of
timer and clock

When the wire controller
appears abnormal
condition,use a sharp­pointed article to press this
button to make the wire
controller resume normal

After cleaning the air inlet,
press this button, the unit
can start to operate

24.Time Adjusting button

23.Sleep button
Used to set Sleep state

When there is too much dust collected on
the air inlet, the wire controller will show
this display to remind theuser to clean the
air inlet.After cleaning and installation,
just press the air filter reset button.

25.Reset button

26.Air Filter Reset button

27.Timer button
Used to set the

mode of timer

28.Lock state display

22.Setting button
Used to confirm the time

of timer and clock

29.Health
Used to control the
generating oxygen
function and negative
ion-function

30.Remote control window
Used to receive the
remote control signal

14.Network control display

15.Working mode display

2

Parts and Functions

Calibration of clock

When turning on the unit for the first time, the clock should be calibrated. The method of calibration is:

1.Press "Clock" button, the Clock display " AM" " PM" will flash.

2.Press or to adjust time. For each press, the time will increase or decrease 1 minute. If depressing
the button, the time will increase or decrease rapidly.

3.After confirming the time, press " Set" button, " AM" or " PM" will stop flashing,the clock will begin to work.

Note:

1.This model does not have the following related display and function

2.The outdoor unit no oxygen-bar function or no negative ion unit no health function and health display.

3.HEAT button:

This button can only be used for units with electric heater function.

29

10

5 6 7 9 11

12

14

16

26

SUR

1

2

3

4

5

6

7

8

9

11

12

13

14 15 16 17 18

20

21
22

23
24
25
26
27
28

AUTO

10

19

MODE

FAN SWING

TEMP

CLOCK

SET

TIMER

SLEEP

RESET

ON/OFF

SET

HEALTH

29

17.Operation mode button

21.Clock button
Used to calibrate the time
of timer and clock

16.Electric heating display

Used to set working mode:
Auto, Cooling, Dehumidifying,
Heating, Fan

18.Fan speed button
Used to set fan speed: Low
Fan, Med Fan, High Fan, Auto

20.Temperature Setting button
Used to set temperature,

temperature range: 16 C~30 C

19.Swing button

Used to set Auto Swing or
Fixed air sending direction

Working
mode

Auto
operation

Cooling
operation

Dehumidifying
operation

Heating
operation

Fan
operation

Wire
controller

12.Humidifying state display

Used to turn on/off unit

1.ON/OFF button

6.Air filter cleaning display

*

7.Super/Soft operation display

2.Temperature display

8.Fan speed display

9.Auto Swing display

11.Fresh air state display

4.Timer ON/OFF display

3.Clock display

5.Humidity display

10.Health state display

Auto

Low Fan Med Fan High Fan Auto

13.Sleep state display

FILTER RESET

HEAT

31.HEAT Button

30
31

15.SET Button

Used to confirm TIMER and CLOCK settings when
heating or cooling.

3

Parts and Functions

Remote controller

1.TEMP Setting Button

(Used to set temperature. Setting ranges:
16 C to 30 C)

2.SWING Button

If you press this button once, auto swing will be
activated.
If you press this button again, the louver will fix
in the present position.

3.Power ON/OFF Button

Used for unit start and stop

After power on, the LCD of remote controller will
display the previous operation state (except for
TIMER,SLEEP and SWING state).

4.Operation MODE

Used to select operation mode.

Every time you press MODE button, operation mode
changes according to following sequence:

The function of code A

6.CLOCK Button

Used to set correct time.

7.TIMER Button

Used to select TIMER mode:TIMER
ON,TIMER OFF, TIMER ON/OFF.

(Note: if time of TIMER ON is the same as TIMER OFF,TIMER
ON/OFF cannot be set)

10.RESET Button

Press this button by using a sharp article to resume the
correct operation of the remote controller in case of need,
i.e. for example in case of malfunctions due to
electromagnetic disturbance.

5.HEALTH Button

13.HOUR Adjustment

Used to set clock and timer setting

8. FILTER Button

Used to set up/down function of filter.

NOTE: 1.Single cooling air conditioner does not have the displays and functions related to heating.

2.Some functions of this controller maybe not available according to the corresponding PCB's functions,such
as: In function of code A which are optional for different unit.

3.HIGH/SO button:This button is active in Cooling/Heating mode, the fan speed is in AUTO mode after pressing
it and " high functon/soft function " will be automatically cancelled after 15 minutes running.

4.HEAT button:

This button can only be used for units with electric heater function.

9.CODE Button

Used to select Code A or B,

Series

wired remote controller

units use Code A,

Series

remote controller units use code B.

14.HIGH/SO Button

Used to select HIGH or SOFT operation.

11.LIGHT Button

Used to light the control panel (only for cabinet unit)

12.LOCK Button

Used to lock operation button and LCD display contents: by
pressing this button, other buttons comes out of function and
lock state display appears; if you press it again, lock state
will be no more active and lock state display will disappear.

The function of code B

AUTO

FAN

HEAT

COOL

DRY

FRESH

HIGH/SO

TIMER

SET

FILTER

B

A

M D

HEALTH

RESET

LOCK

SLEEP

FAN

TEMP

ON
OFF

SWING

MODE

CLOCK

CODE

LIGHT

OFF

A
U
T
O

25

26

21

23

17

15

18

19

22

24

27

20

14

16

36

1

2

3

4

6
7

9

10

5

8

34

33

28

32

31

30

35

29

The function of code A

Used to select TIMER mode:TIMER
ON,TIMER OFF.

The function of code B

852 16 28 30 33291411 17 21 24

HEAT

13
37

12
11

HEAT

COOL

DRY

8

At night, before going to bed you can press
down the SLEEP button on the controller
and the air-conditioner will run by the
comfortable sleeping mode to make you sleep
more comfortable.

In cooling, dehumidifying mode

In heating mode

Comfortable Sleep

Note: In AUTO mode, unit will run in SLEEP function according to the operation mode.
After setting SLEEP function, it is forbidden to calibrate clock.
If the set sleep-time does not reach 8 hours, the unit will stop operation automatically after set time
is complete.
Set "TIMER-OFF" function first, then set SLEEP, and the sleep-set is performance; set TIMER-ON
function first, the sleep function can only be set before TIMER-ON; if set theSLEEP function first,
the TIMER function can not be set.

Note: Before using this function of code A, must
adjust the clock, or the sleep function will be disordered.

After setting sleep function, not allowed to adjust the clock. Can't use the remote controller operate the
AC. If so, please cancel the sleep function first.
After setting sleep function, can't set the timing function.

One hour after start up, the temp. decrease 2 lower than the setting one. After another hour decrease by
more 2 .
The temperature will automatically rise by 1 after another 3hrs' operation, and then automatically close
after 3hrs' continuous operation. The actral temperature is lower than the setting one which is to prevent
from being too hot to your sleep.

One hour after sleeping operation start, the temp. is 1 higher than the setting one. After another hour the
temp. rises 1 and then run continuously for another 6hrs' and then close. The actual temp. is higher than
the setting one which is to prevent from being too cool to your sleep.

FRESH

HIGH/SO

TIMER

SET

FILTER

A

HEALTH

RESET

LOCK

SLEEP

FAN

TEMP

ON

OFF

SWING

MODE

CLOCK

CODE

LIGHT

OFF

A
U
T
O

Operation

SETTING T

SLEEP RUN BEGINS SLEEP RUN STOPS

1 hr

1 hr

3 hrs

about 3 hrs

decrease 2

decreases 2

increase1

SHUT DOWN

Heat mode

about 6 hrs

1 hr

1 hr

increase 1

increase 1

SLEEP RUN STOPS

SLEEP RUN BEGINS

SETTING T

SHUT DOWN

Cooling mode

The function of code A:Sleep function

*

MODE

FAN

HEALTH

TEMP

CLOCK SET

TIMER SLEEP

RESET

ON/OFF

AM

SET

OFF

AM

SWING

FILTER RESET

HEAT

HEAT

Just press TIMER button several times until TIMER mode disappears.

OFF

ON

OFF

ON OFF

Used to select Auxiliary electric heater.

2

RESET

LOCK

SLEEP

FAN

TEMP

ON

OFF

SWING

MODE

CLOCK

CODE

LIGHT

Battery loading
Batteries are fitted as follows:

Loading the battery

Ensure that batteries are correctly placed in the compartment
as required for positive and negative terminals.

Replacing the battery compartment lid

The battery compartment lid is reinstalled in the reverse
sequence.

Display review

Press the button to see if batteries are properly fitted. If no
display appears, refit the batteries.

Remove the battery compartment lid
Slightly press and disengage the battery compartment lid marked
with

" "

and then hold the remote controller by the upper
section and then remove the battery compartment lid by pressing
in the direction of the arrow as shown in the figure above.

Note:
It is recommended that the batteries be removed from the
compartment if the remote controller is not used for an extended
period.
The remote controller is programmed for automatic test of
operation mode after the batteries are replaced. When the test
is conducted, all icons will appear on the screen and then
disappear if the batteries are properly fitted.

When the display become weak, this display no power
in the battery, please change the battery.

Caution:
If the remote controller does not operate as designed after
fitting new batteries of the same
type, press the Reset button (marked ) with a pointed article.

+ -

- +

RESET

LOCK

SLEEPMODE

CLOCK

CODE

LIGHT

A
U
T
O

A
U
T
O

7

blank

ON

Operation mode will be displayed on LCD.
Power indicator lights up.

Every time the button is pressed, display changes as
follows:

Select .

(3)Time setting for TIMER ON

Press TIME button.

(5)Time setting for TIMER OFF

To cancel TIMER mode

Every time the button is pressed, time increases 10min.
If button is kept depressed, time will change quickly.
Every time the button is pressed, time decreases 10min.
If button is kept depressed, time will change quickly.
Time will be shown on LCD.
It can be adjusted within 24hours.

AM refers to morning and PM to afternoon.

Time displayed: Unit starts at Xhour X min.

After time setting, press TIMER button to
confirm."ON" stops blinking, While "OFF"
starts blinking.

(4) Time confirming for TIMER

Follow the same procedures in "Time setting
for TIMER ON".

(6)Time confirming for TIMER OFF

After time setting, press SET button to confirm
"OFF" stops flashing.
Time displayed: Unit stops at X hour X min.

According to the Time setting sequence of TIMER ON or TIMER OFF, either Start-Stop or Stop-Start
can be achieved.

(1)After unit start, select your desired operation mode

(2) Press TIMER button to change TIMER mode

ON
OFF

Operation

The function of code A:TIMER ON/OFF

FRESH

HIGH/SO

TIMER

SET

FILTER

A

HEALTH

1

HEAT

*

MODE

FAN

HEALTH

TEMP

CLOCK SET

TIMER SLEEP

RESET

FILTER RESET

ON/OFF

PM

AM

1

SET

SWING

HEAT

6

3

2

4

5

4

Parts and Functions

When operating the remote controller in an area where
electronically controlled lights are installed or wireless handsets
are used, please move closer to the indoor unit as the function
of the remote controller might be affected by signals emitted by
the above mentioned equipments.

Battery loading

Confirmation indicator

If no indication is displayed after press ON/OFF button,
reload the batteries.

Remote Controller Operation

When in use, direct signal transmission head to
the receiver placed on the indoor unit

The distance between the remote controller and the receiver
should be max 7m and there should be no obstacle between them.
Do not throw the remote controller; prevent it from being damaged.

Clock Set

When unit is started for the first time and after replacing batteries in remote controller, clock should
be adjusted as follows:

1.Press CLOCK button, clock indication of " AM " or " PM " flashes.

2.Press or to set correct time. Each press will increase or decrease 1 min. If the button is kept
pressed, time will increase or decrease quickly.

3.After time setting is confirmed, press "SET" : AM or PM stop flashing, while clock starts working.

Note:AM means morning and PM means afternoon.

FRESH

HIGH/SO

TIMER

SET

FILTER

HEALTH

HEAT

16.FRESH Button

Used to set fresh mode, the unit will draw in fresh air.

Displays when healthy run function is set.

22.TEMPERATURE Display

34.LOCK State Display

33.BATTERY Energy Display

Notify the user when it is time to change the batteries.

24.HIGN/SO Run Display

26.SIGNAL SENDING Display

28.Fresh Display

29.Auxiliary ELECTRICAL HEATING Display

30.HEALTH Display

32.SLEEP State Display( In function of code A)

31.Operation MODE Display

35.FAN SPEED Display

23.AUTO SWING Display

20.TIMER Display

21.FILTER Display

36.TIMER ON Display

17.SLEEP Button(In function of code A)

(The clock must be corrected before setting sleep function)

Used to set sleep mode.

18.FAN Button

Used to select fan speed:LOW,MID,HIGH,AUTO.

19.TIMER OFF Display

When the filter need be cleaned, the sign will
appear automatically.

25.Code A display

27.Code B display

The function of code A The function of code B

LOW

MID

HIGH AUTO

LOW

MID

HIGH AUTO

37.HEAT Button

1

4

5

6

3

2

3

AUTO

RESET

LOCK

SLEEP

FAN

TEMP

ON

OFF

SWING

MODE

CLOCK

CODE

LIGHT

A
U
T
O

A
U
T
O

A
U
T
O

5

Use COOL in summer.Use HEAT in winter.
Use DRY in spring,autumn and in damp climate.

(1) Unit start

(2) Select operation mode

(3) Select temp. setting

Press ON/OFF button, unit starts.
Previous operation status appears on display
(Not Timer setting). Power indicator lights up.

Press MODE button. For each press, operation
mode changes as follows:

Unit will run in operation mode displayed on LCD.Stop display at your desired mode.

Every time the button is pressed, temp. setting
increases 1 C.
If button is kept depressed, temp.setting will
increase quickly.
Every time the button is pressed, temp. setting
decreases 1 C.
If button is kept depressed, temp. setting will
decrease quickly.

Recommendations

(4) Fan speed selection

Unit will start running to reach the temp. setting
on LCD.

Press TEMP button

Auto running: During the Auto running mode, air conditioning running and can auto-select the cooling,
heating, fan mode according to the room temperature.
Fan running: The AC only have air supply running no cooling and heating running at the condition, AC
can't have auto air supply running, and can't display the setting temperature value on the LCD.
During the heating running, after start the AC, in order to prevent cooled air, AC can stop for a while be­fore send heat air.
During the dehumification running, when the room temp. setting temp. , not setting condition according
to the air speed.

AUTO

MODE

FAN

HEALTH

TEMP

CLOCK SET

TIMER SLEEP

RESET

ON/OFF

AM

SWING

Hints

Wire controller can memorize each operation
status.
When starting it next time, just press ON/OFF
button and unit will run in previous status.

Press FAN button. For each press,
fan speed changes as follows:

Unit runs at the speed displayed on LCD.In HEAT
mode, warm air will blow out after a short period
of time due to cold-draft prevention function.
In DRY mode, when room temp. becomes 2 C
higher than temp. setting, unit will run intermitte­ntly at LOW speed regardless of FAN setting.

Press ON/OFF button.
Only time and room temp remains on LCD.
All indicators go out.
Vertical flap closes automatically.

(5) Unit stop

Remote controller

LOW

MID HIGH

AUTO

Wire controller

FRESH

HIGH/SO

TIMER

SET

FILTER

A

HEALTH

1

5

4

Operation

The function of code B

AUTO COOL DRY FANHEAT

The function of code A

COOL DRY HEAT

LOW

MID

HIGH AUTO

The function of code A The function of code B

LOW

MID

HIGH AUTO

FILTER RESET

HEAT

HEAT

6

Hints:

Set Clock correctly before starting Timer operation.

You can let unit start or stop automatically at following time: Before
you wake up in the morning, or get back from outside or after you
fall asleep at night.

Operation mode will be displayed
on LCD.Power indicator lights up.

(2)TIMER mode selection

Press TIMER button to change
TIMER mode.Every time the
button is pressed, display
changes as follows:

TIMER ON/OFF

Wire controller possesses memory function, when use TIMER mode next time, just
press SET button after mode selecting if timer setting is the same as previous one.

(1)After unit start, select your
desired operation mode.

Please close health function first before setting Timer, then you can do the TIMER ON
operation.Please do not use the health function when in TIMER ON state.

Wire remote controller or remote controller can memorize each working condition. Next time
open the unit, only need to press the ON/OFF key, the AC can work according to last time
working condition.(Timing, Sleeping and Swing mode not included.)

From Timing close to timing open, can setting sleep mode.

ON

MODE

FAN

HEALTH

TEMP

CLOCK SET

TIMER SLEEP

RESET

FILTER RESET

ON/OFF

AM AM

1

SET

3

4

2

SWING

Operation

Select your desired TIMER mode (ON or OFF)

(3)Timer setting

Press TIME button.

Every time the button is pressed, time increases 10min.If button is kept
depressed, time will change quickly.
Every time the button is pressed, time decreases 10min.If button is kept depressed,
time will change quickly.
Time will be shown on LCD. It can be adjusted within 24hours.

(4)Confirming your setting

After setting correct time, press SET button to confirm "ON" or "OFF" stops flashing.
Time displayed: Unit starts or stops at x hour x min (ON or OFF). Timer mode indicator lights up.

To cancel TIMER mode

Just press TIMER button several times until TIMER mode disappears.

According to the seting timing open, close sequence, can realize first open then colse the unit or first
close then open the unit.

The function of code B

The function of code A

blank

ON

OFF

ON

OFF

blank

ON

OFF

HEAT

FRESH

HIGH/SO

TIMER

SET

FILTER

A

HEALTH

RESET

LOCK

SLEEP

FAN

TEMP

ON

OFF

SWING

MODE

CLOCK

CODE

LIGHT

1

4

HEAT

5

1

3

2

4