Twin-tub Washing Machine
User's manual
Twin-tub Washing Machine
This manual is for
User's manual
Please read this manual
carefully before using.
Retain it for future reference.
Contents
Packing list
Names of the parts
Safety precautions
Installation and adjustment
Preparation before washing
The musts in washing
Usage of the detergent
Washing sequence
Disposal after washing
Trouble-Shooting Answers to question
Specification
Packing list
Name
User's manual
The cover 2
Quantity
One piece
Water inlet hose
Lint filter
Gland
Twin-tub washing machine
One piece
One piece
One piece
One set
Names of the parts
water-filling translation
Valve cover
Meaning and description of the symbols
Contents marked with that symbol are related
Warning sign
Forbidding sign
Please check if the power receptacle has good earthing
condition before using to guarantee your safety.
to the safety of the product and the personal
safety of the users. Please operate in strict
conformity to the contents, otherwise it may
cause damage of the machine or injure the
personal safety of the user.
Contents marked with that symbol are actions
forbidden to perform. Performing of those
actions may result in damage of the machine
or injure the personal safety of the user.
1
Safety precautions
Please insert the power cord into
special receptacle with rated voltage.Be sure to use single-phase
three pins receptacle.The earthing
terminal of the receptacle must be
earthed reliably.If possible,please
adopt electric leakage protector.
When the machine is normally
using, please put the power plug
at the location easily to be inserted and extracted by hand. Be sure
to pull the plug off when there's
power failure, or the machine is
being moved, cleaned or when it
is idle.
Earth
If the supply cord is damaged,it must be replaced
by the manufacturer or its service
agent or a similarly qualified person
in order to avoid a hazard.
Do not put the machine at damp
place like the bathroom . Never
wash it with water. Do not place
wet laundries on the control panel.
Do not use water hotter than50 C .
For washing machine with ventilation
openings in the base, that a carpet
must not obstruct the openings.
Ventilation hole at
the bottom of the
washing machine
Do not let the machine share one receptacle
with other electric appliances. If the power
plug is damaged, or the plugging into the
receptacle is loose, do not use the plug any
more.
2
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations.
Safety precautions
Do not stretch hands into the working
machine. It is dangerous even if the
rotation is slow. Take special care of
the children.
Do not put any hot or heavy items
( such as the kettle with hot water )
on the washing machine.
Handicapped or children without care
shall not use the machine.
Do not decompose, repair or alter the
machine by yourself.
Do not wash laundries with volatile
materials (such as thinner, petrol etc.).
Petrol
Keep the machine away from direct
sunlight and heat source like the
heater.
er
inn
Th
To protect your laundries and washing machine, please take out all of the
coins, buttons, sand, hairpin and
other foreign materials before washing.
Please check if the connection of the
water inlet pipe is proper.
It is suggested to use foamless washing
powder.
3
Installation and adjustment
Please install and adjust the machine according to the requirement of
the manual. It is very important to your security and correct operating
the machine.
Install the lint filter
After opening the package,please take out the lint
filter from the document bag,install it to the overflow
filter of the wash tub.See to the figure.
Overflow filter
Lint filter
Usage of the drain hose
The drainage shall be smooth with the drain hose.
1.The height of the drain hose shall be
less than 10cm , or the drainage will
not be smooth enough and cause
incomplete drainage.
2.Do not tramp or press the drain hose.
<10cm
3.If the drain hose is too long, cut it at mid point.
To make smooth drainage, cut the front end of
the hose slantingly.
4.If extra drain hose is needed , please make
separate purchase. The inner diameter of the
extra hose shall not less than 30mm, and the
length shall not exceed 1.5m.
If the extra hose is too long, cut it either
at point A or B.
4
> 30mm
<1.5m
BA
How to change the direction of the drain hoses
Figure 1 indicates the ex factory installation
position of the drain hose.
Soft item
Extend the drain hose from the side of wash tub.
Put soft items on the ground. Lean the machine
down gently with the front surface facing the
ground. Take off the drain hose from the cabinet.
Take the hose out of the fixing groove.
(See to Figure 2).
Figure 1
Soft item
Figure 2
Embed the drain hose into the groove along the side
of the spin tub in the order of (1)~(3), heading for the
side of the wash tub. (See to Figure 3).
Embed the drain hose into the groove with
hands. Take care not to damage the drain
hose in fastening the fixing clamp.
Extend to the
spin tub side
Figure 3
Embed into the
groove in turn
Install the water inlet hose; Select the water level
Insert the water inlet hose into the water-filling
entrance on the control panel directly.(pull it
out to dismantle it)
Select water level according to the
quantity of the laundries.
Set the water level adjusting lever
to needed line.
Use the new water inlet hose provided
with the machine to connect to the
water faucet.Old hose sets should
not be reused.
Water inlet hose
Maximum
Medium
Minimum
Water-filling
entrance
Water level
indicator
Max.
Med
Min
5
Preparation before washing
Preparation before washing
1.Connect the water inlet hose.
2.Confirm that the washing machine is earthed
reliably . Then insert the power plug into the
receptacle. Do not connect the earth terminal
to the gas pipe and tap water pipe.
3.Put down the drain hose .
4.Slanting or uneven ground may result in
unstable working or abnormal noise. Please
make the machine stand horizontally.
Pay attention to followings before washing the laundries
Check if
the laundries
has special
requirement
on washing
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries that are not colorfast from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like
mud or dust. For the parts with heavy soil, please apply detergent on
them in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn
it over before putting in.
f. Do not put those laundries polluted by chemicals into the washing
machine directly.
Clear the
pocket. Take
out the coins,
sand, hairpins
etc.
Tie the long
strips; fasten
the buttons;
close zippers.
The quantity of
the laundries
shall not be too
large. Stretch
and loosen the
laundries before
putting them in
the tub.
When the pulsator
is running , the
buttons of the
laundries may
cause noise. For
the sake of
discretion, please
put the laundries
with buttons into
other laundries.
6
The musts in washing
The capacity of washing and spinning of the
machine refer to the weight of the
standard laundries under dry condition that can
be washed or spinned in one time. Laundries
quantity in one washing cycle shall be lower
than the standard capacity.
the largest capacity is only the loading capacity
of the drum
The thickness ,size , type of the cloth will influence the actual washing capacity. It is suitable to put in reasonable amount of laundries
and the laundries can be turned round in washing for one time washing.
Do not select " Maximum " water level for
laundries less than 1.0kg, so as to avoid
splashing of water.
It is suggested not to use high sudsing detergent.
Usage of the detergent
How to use the whitener
Fill water to decided level. Dilute
the whitener with container.
Pour it slowly into the washing tub.
Avoid using whitener on laundries with color or pattern as they
are prone to lose color.
The whitener shall not touch
the laundries directly.
Refer to the user's manual for
the usage and quantity of the
whitener.
For powder whitener, please
dissolve it before using.
How to use the washing powder
Direct dissolved in the machine:
1.Fill small quantity of water.
2.Add the powder . Run for 30
seconds to dissolve it completely.
3.Put in laundries. Select suitable
water level.
The instant dissolving of the washing
powder:
1.Prepare warm water of 30 C and a
container.
2.Add the powder while stirring to fully
dissolve it.
The powder is more prone to pollute the
laundries than the detergent. Therefore
please use it with proper quantity.
Dosage of different washing powder is
different. Please refer to the instruction
of the washing powder for the detail
dosage.
7
STANDARD
STRONG
DRAIN
Washing sequence
WASH TIMER
OFF
12
9
6
3
15
WASH SELECTOR
STANDARD
STRONG
DRAIN
SPIN TIMER
1
4
3
2
5
OF
F
O
FF
12
9
6
3
15
STANDARD
STRONG
DRAIN
Wash timer
(To set to below 2 minute,
first set to 5 minute then
turn it back. it can increase
the service life of the timer).
WASH TI MER
Wash selector
(Strong current,
standard current)
STRONG
STANDARD
DRAIN
WASH SELECTOR
Spin timer
(to set to below 1 minute,
first set to 2 minute then
turn it back. it can increase
the service life of the timer).
OF
F
SPIN TIMER
Wash
Figure 1
SPIN
INLET SELECTOR
WASH
Figure 2
STRONG
STANDARD
DRAIN
Figure 3
1 Inlet selector
(1) Set inlet selector to Wash side. Figure 1
(2 )Adjust water level rod to a position as needed.
2. Fill the water and add the dissolved washing
powder to make the water level reach the preset
position. (Figure 2)
Run washing program for some time to stir and
dissolve the powder completely.
3.Put in the laundries. If the water quantity is
insufficient, please add water.
4.Select the current.
Select the strength of the current according to
the laundries. (Figure 3)
5.Select the washing time
Select the washing time according to the
laundries. (Figure 4)
6.After washing,the buzzer will ring .Set
the "WASH SELECTOR" at "DRAIN".
(Figure 5).
8
STANDARD
OF
F
Figure 4
DRAIN
Figure 5
Midway spinning
1
Set the inlet selector handle on spin side and
fill water for about 1 min.
2
Close the spin tub outer cover and spin
for about 1 - 2 min.
In case water flows out from wash tub side
due
to too much inflow, please turn down
the water tap a bit.
1.Put the laundries into the spin tub evenly and smoothly.
2.Spin
(1) Put the gland in properly.
Please put in the gland properly even if the
laundries quantity is small.
Push
Gland
Push
3.Run the foam-removing spinning.
Set the inlet selector handle on spin side and
1
fill water for about 1 min.
In case water flows out from wash tub side
due to too much inflow, please turn down
the water tap a bit.
Close the spin tub outer cover and spin
2
for about 1 - 2 min.
Proper
The laundries
are slanting
Proper
No gland
(2) Close the inner and outer cover of the spin tub.
Outer cover of
The spin tub
(3) Spin for 1-2 minutes.
Inner cover of
The spin tub
Inlet selector handle
Water inlet
Wash
Inlet selector
9
Spin
Rinsing
Rinse with water-filing
1.Put the laundries into the wash tub. Select
suitable current according to the laundries.
2.Adjust the water level
Set the water level with water level adjusting
lever according to the laundries quantity.
Then fill suitable water continuously.
3.Rinse
Adjust the wash timer to 5-7 minutes to do
rinsing.
(Repeat the midway spinning and rinsing with stored water
for 2-3 times)
OVERFILL
If you find water flowing out here,please
twist the water tap to
limit the water filling.
Rinse with stored water
1. Put the laundries into the wash tub. Select suitable current according to
the laundries.
2. Fill water to preset water level.
3. Rinse
Adjust the wash timer to 2-3 minutes to do rinsing.
When the laundries quantity is few, please use "Soft" current.
If you use "Standard" current, it may splash.
10
Spinning
1. Put the laundries into the spin tub
evenly and smoothly.
2. Press the gland in the tub properly.
Close the inner and outer cover of
the spin tub.
3. Spin
Select suitable spin time according
to the laundries, and do spinning.
During spinning, if there's abnormal
sound, it is generally owing to slanting
placement of the laundries. Please
stop the machine and re-order the
laundries.
In spinning, it will pause the work if you open the outer cover of the spin
tub. Close it to resume the spinning.
To do spinning and draining
or rinsing with water-filling
together, please first do
spinning for around 1 minute,
then do draining or rinsing
with water-filling. Otherwise
the spinning will stop owing
to too much water stored in
the spin tub.
11
Disposal after washing
After using, please clean the lint and eyewinker of the lint filter and
overflow filter in time. Otherwise it may influence your using the machine.
Please first pull off the power plug from the receptacle before cleaning.
Cleaning the lint filter
The lint filter must be used during washing.
It must be cleaned in time after each using.
1. Take off the lint filter
Put hand at the indicated position.
Push down to take it off. ( See
Figure 1)
2. Clean the lint
Put it in water and clean while it is
still wet.(See Figure 2)
3. Install the lint filter
After cleaning, insert the bottom
of the lint filter ( marked with
"down side") into the overflow filter ,
then push the upper part of the
filter in ( marked with " up side ").
(See Figure 3)
Figure 2
Cleaning the overflow filter
Too much lint on the overflow filter will influence
the normal usage of the machine. Please
clean it every two months.
Take off the overflow filter.
As indicated in the figure, nip the elastic fixing
claw and pull it to the direction of the arrow to
take it off.
Elastic fixing
claw
Figure 1
Figure 3
12
Cleaning the overflow filter
2. Take off the corrugation pipe.
Dismantle the upper part of the
corrugation pipe inside the
overflow filter ( as indicated in
Figure 1).
3. Cleaning the overflow filter
Clean the lint around the filter
and flush with tap water.
4. Install the overflow filter.
(1).Install the corrugation pipe.
(2).Insert the mounting plate at
the bottom of the filter into
the valve cover.
(3).Hang up the hook at the left
upper side.
(4).Push the upper part in as
indicated in Figure 2.
Hook
Water level
adjusting lever
Figure 1
Figure 2
Cleaning the protective cover
During washing clothes,must use
Finished washing everytime ,please clean lint on the
surface
Please clean lint under the termly
protective cover
protective cover
Corrugation
Pipe
Cleaning method:
1.Push as the figure ,take down the protective
cover as the arrowhead way
13
Down
Push
Cleaning the
protective cover
2.cleaning dirty under the
protective cover
take out the sundries using the plier or other wiry
3.install the
protective cover
after cleaning, install it as origin assure it reliable
Disposal of the complete unit
After washing, dismount the water inlet
Wipe the complete unit with soft
cloth twisted dry.
Wipe with neutral detergent if too dirty
Do not wash it directly by water
Thinner
Petrol
Alcohol
hose.
Do not store water in the tub for long
period. Discharge the water immediately
after each using.
Pull off the power plug and hang up the
power cord.
Hang up the drain hose.
Wipe off the water drops on the surface
and inside the tub with clean soft cloth.
Open the cover of the wash tub and the
inner/outer cover of the spin tub for
some time (about one hour), then close
them.
Trouble-shooting Answers to question
If the laundries fall to the outer side of the spin tub
If the laundries fall to the outer side of the spin tub,
Please contact the after-sales service department.
14
Trouble-shooting Answers to question
(If there's breakdown, please pull off the power plug before checking) The following
phenomena are not breakdowns sometimes. Please confirm again before sending
it to repair. If there are real breakdowns, please come to the special maintenance
department or after-sale service department of our company. Do not repair it by yourself.
Phenomena
The machine does
not act.
The draining
does not work
There's abnormal
sound during washing
There's abnormal
sound and violent
vibration during
spinning
Is there power failure?
Is the power plug loose?
Is the pulsator twisted by
foreign materials?
Is the drain hose put down?
Is the drain hose blocked by
foreign material?
Are there laundries falling to
the outer side of the spin tub?
Are there hair pin, coins or
metal items brought inside
the tub?
Is the machine slanting?
Is the gland pressed evenly?
Are there laundries falling to
the outer side of the spin tub?
Are the laundries in spin tub
too much?
The reason
How to settle
Use it when the power is on.
Insert the power plug tightly.
Remove the foreign materials?
Put down the drain hose?
Remove the foreign material?
Please contact the after-sales
service department.
Remove the hair pin, coins or
metal items
Level the machine properly.
Pressed the gland evenly
Remove the laundries
Remove a little laundries
Specification
Water level Water quantity about (L)
Washing capacity(kg)
Spinning capacity(kg)
Injection pressure(MPa)
Maximum/48 Medium/39 Minimum/33
7.0
4.5
0.02~0.2
15
Loading...