This manual contains proprietary information, which is protected by
copyright. All rights are reserved. No part of this manual may be
photocopied, reproduced or translated to another language without
prior written consent of Good Will company.
The information in this manual was correct at the time of printing.
However, Good Will continues to improve products and reserves the
rights to change specification, equipment, and maintenance
procedures at any time without notice.
Good Will Instrument Co., Ltd.
No. 7-1, Jhongsing Rd., Tucheng Dist., New Taipei City 236, Taiwan.
Menu Tree .......................................... 287
GSP-9330 Specifications .................... 332
GSP-9330 Dimensions ....................... 340
Declaration of Conformity .................. 341
INDEX .......................................................................... 342
2
SAFETY INSTRUCTIONS
WARNING
Warning: Identifies conditions or practices that
could result in injury or loss of life.
CAUTION
Caution: Identifies conditions or practices that
could result in damage to the instrument or to
other properties.
DANGER High Voltage
Attention Refer to the Manual
Earth (ground) Terminal
Frame or Chassis Terminal
Do not dispose electronic equipment as unsorted
municipal waste. Please use a separate collection
facility or contact the supplier from which this
instrument was purchased.
SAFETY INSTRUCTIONS
This chapter contains important safety
instructions that you must follow during
operation and storage. Read the following before
any operation to ensure your safety and to keep
the instrument in the best possible condition.
Safety Symbols
These safety symbols may appear in this manual or on the
instrument.
3
GSP-9330 User Manual
General
Guideline
CAUTION
Do not place any heavy object on the
instrument.
Avoid severe impact or rough handling that
leads to damaging the instrument.
Do not discharge static electricity to the
instrument.
Use only mating connectors, not bare wires, for
the terminals.
Ensure signals to the RF input do not exceed
+30dBm.
Ensure reverse power to the TG output terminal
does not exceed +30dBm.
Do not supply any input signals to the TG
output.
Do not block the cooling fan opening.
Do not disassemble the instrument unless you
are qualified.
(Measurement categories) EN 61010-1:2010 specifies the
measurement categories and their requirements as follows. The
instrument falls under category II.
Measurement category IV is for measurement performed at the
source of low-voltage installation.
Measurement category III is for measurement performed in the
building installation.
Measurement category II is for measurement performed on the
circuits directly connected to the low voltage installation.
Measurement category I is for measurements performed on
circuits not directly connected to Mains.
Safety Guidelines
4
SAFETY INSTRUCTIONS
Power Supply
WARNING
AC Input voltage range: 100V~240V
Frequency: 50/60Hz
To avoid electrical shock connect the protective
grounding conductor of the AC power cord to
an earth ground.
Battery
CAUTION
Rating: 10.8V, 6 cell Li-ion battery
Turn off the power and remove the power cord
before installing or removing the battery.
Cleaning
Disconnect the power cord before cleaning.
Use a soft cloth dampened in a solution of mild
detergent and water. Do not spray any liquid.
Do not use chemicals containing harsh material
such as benzene, toluene, xylene, and acetone.
Operation
Environment
Location: Indoor, no direct sunlight, dust free,
almost non-conductive pollution (Note below)
Temperature: 5°C to 45°C
Humidity: <90%
(Pollution Degree) EN 61010-1:2010 specifies the pollution degrees
and their requirements as follows. The instrument falls under
degree 2.
Pollution refers to “addition of foreign matter, solid, liquid, or
gaseous (ionized gases), that may produce a reduction of
dielectric strength or surface resistivity”.
Pollution degree 1: No pollution or only dry, non-conductive
pollution occurs. The pollution has no influence.
Pollution degree 2: Normally only non-conductive pollution
occurs. Occasionally, however, a temporary conductivity caused
by condensation must be expected.
Pollution degree 3: Conductive pollution occurs, or dry, non-
conductive pollution occurs which becomes conductive due to
condensation which is expected. In such conditions, equipment
is normally protected against exposure to direct sunlight,
precipitation, and full wind pressure, but neither temperature
nor humidity is controlled.
Do not dispose this instrument as unsorted
municipal waste. Please use a separate collection
facility or contact the supplier from which this
instrument was purchased. Please make sure
discarded electrical waste is properly recycled to
reduce environmental impact.
6
SAFETY INSTRUCTIONS
Green/ Yellow:
Earth
Blue:
Neutral
Brown:
Live (Phase)
Power cord for the United Kingdom
When using the instrument in the United Kingdom, make sure the
power cord meets the following safety instructions.
NOTE: This lead/appliance must only be wired by competent persons
WARNING: THIS APPLIANCE MUST BE EARTHED
IMPORTANT: The wires in this lead are coloured in accordance with the
following code:
As the colours of the wires in main leads may not correspond with
the coloured marking identified in your plug/appliance, proceed
as follows:
The wire which is coloured Green & Yellow must be connected to
the Earth terminal marked with either the letter E, the earth symbol
or coloured Green/Green & Yellow.
The wire which is coloured Blue must be connected to the terminal
which is marked with the letter N or coloured Blue or Black.
The wire which is coloured Brown must be connected to the
terminal marked with the letter L or P or coloured Brown or Red.
If in doubt, consult the instructions provided with the equipment
or contact the supplier.
This cable/appliance should be protected by a suitably rated and
approved HBC mains fuse: refer to the rating information on the
equipment and/or user instructions for details. As a guide, a cable
of 0.75mm2 should be protected by a 3A or 5A fuse. Larger
conductors would normally require 13A types, depending on the
connection method used.
Any exposed wiring from a cable, plug or connection that is
engaged in a live socket is extremely hazardous. If a cable or plug is
deemed hazardous, turn off the mains power and remove the cable,
any fuses and fuse assemblies. All hazardous wiring must be
immediately destroyed and replaced in accordance to the above
standard.
This chapter provides a brief overview of the
GSP-9330, the package contents, instructions for
first time use and an introduction to the front
panel, rear panel and GUI.
The GSP-9330 builds on the strong feature set of the GSP-9300 and
significantly increases performance in almost every aspect; making
this the most comprehensive and feature-rich spectrum analyzer
GW Instek has released.
Like the GSP-9300, the GSP-9330 features a split window display to
view data in spectrum, topographic or spectrographic views. There
are also a number of additional test functions such as 2FSK, P1DB
and new dedicated EMC pretest functions for EMI and EMS testing.
Lastly, the GSP-9330 significantly reduces the sweep time.
Main Features
9
GSP-9330 User Manual
Two operating modes: Spectrum and Power
Meter mode
EMI Pretest functions
SEM measurement
ACPR measurement
OCBW measurement
2FSK measurement
Phase jitter measurement
Harmonics measurement
P1dB measurement
Channel power measurement
Demodulation analyzer
Diverse marker functions and features with
Peak Table
Sequence function to automatically perform pre-
programmed sequential operations
EMI quasi-peak and average detector
Optional battery operation
Interface
8.4 color LCD (800600)
On-screen menu icons
DVI-I video output
RS-232 with RTS/CTS hardware flow control
USB 2.0 with support for USB TMC
LAN TCP/IP with LXI support
Optional GPIB/IEEE488 interface
Optional 3G USB adapter for WLAN
Optional power meter adapter
IF output @ 886MHz
Headphone output
REF (reference clock) input/output BNC ports
10
GETTING STARTED
Alarm/Open collector output BNC port
Trigger/Gate input BNC ports
RF N-type input port
Tracking generator output
DC +7V/500mA output SMB port
11
GSP-9330 User Manual
Standard
Accessories
Part number
Description
Region dependant
Power cord
N/A
User manual CD:
Includes: User manual,
Programming manual,
SpectrumShot quick start
guide, SpectrumShot
software, IVI driver
N/A
Quick start guide
N/A
Certificate of calibration
Options
Option number
Description
Opt1.
Tracking generator
Opt2.
Battery (11.1V/5200mAH
Li-ion battery)
Opt3.
GPIB interface (IEEE 488
bus)
Optional
Accessories
Part number
Description
ADB-002
DC BLOCK BNC 50R
10MHz-2.2GHz
ADB-006
DC BLOCK N TYPE 50R
10MHz-6GHz
ADB-008
DC BLOCK SMA 50R
0.1MHz-8GHz
GSC-009
Soft Carrying Case
GRA-415
6U Rack mount kit
Accessories
12
GETTING STARTED
Software Downloads
PC Software for Windows System (SpectrumShot quick
start guide, SpectrumShot software)
3.5mm stereo headphone jack
(wired for mono operation)
USB B
USB B Device port. USB 1.1/2.0
LAN
RJ-45 10Base-T/100Base-Tx
20
Display
Scale and
Reference
level
Attenuation
level
Date
and time
Function
menu
Marker
information
Trace/
Detection
settings
Unassigned
setting
icons
Sweep,
Trigger,
Pre-amp
and USB
settings
Frequency/Bandwidth
settings
Status icons
Sweep
settings
Traces and
waveforms
LXI icon
Entry /
Message
area
Sweep
progress
bar
Scale
Displays the vertical scale of the vertical grid. For
details, see page 49.
Reference level
Displays the reference level. For details, see page
48.
Attenuation
Displays the vertical scale (attenuation) of the
input signal. For details, see page 49.
Date/Time
Displays the date and time. See page 116 for
details.
Marker
information
Displays marker information. For details see page
90.
GETTING STARTED
21
GSP-9330 User Manual
LXI icon
This icon indicates the status of the LXI connection.
For details, see page 268.
Function menu
Soft menu keys associated with the F1 to F7
function keys to the right of the display.
Sweep Mode
This icon displays the sweep mode,
as set by the Sweep Mode key. See
page 75.
Sweep settings
Sweep icon that shows the sweep
status. See page 69 for details.
Trace and
detection settings
Trace icon that shows the trace type
and the detection mode used for
each trace. See from page 77 for
details.
Blank
Unassigned setting icons.
Trigger settings
Trigger icon that shows the trigger
status. See page 85 details.
Pre-amp settings
Pre-amplifier icon that shows the
Pre-amplifier status. See from page
60 for details.
USB settings
Displays the status of the USB A
port.
Status Icons
Displays the interface status, power source status
and alarm status, etc. See the Status Icon Overview
on page 24 for a list of the status icons.
22
GETTING STARTED
Frequency/
Bandwidth
settings
Displays the Start, Center and Stop frequencies,
RBW, VBW, Span and Sweep settings.
Entry/Message
area
This area is used to show system messages, errors
and input values/parameters.
Trace and
waveforms
Main display showing the input signals, traces
(page 77), limit lines (222) and marker positions
(90).
Sweep progress
bar
The sweep progress bar shows the progress of
slow sweeps (greater than 2 seconds).
23
GSP-9330 User Manual
3G Adapter
Indicates that the 3G adapter is
installed and turned on.
Demo Kit
Indicates that the demo kit is
installed and turned on.
PreAmp
Indicates that the pre amplifier is
on.
AC
Shown when running on AC
power.
AC Charge
Shown when the AC power is
charging the battery.
Alarm Off
Alarm buzzer output is currently
off.
Alarm On
Alarm buzzer output is currently
on.
Amplitude Offset
Indicates that the amplitude-shift is
active. This icon appears when
amplitude-related functions are
used:
Reference level offset
Amplitude Correction
Input Z = 75Ω and Input Z cal >0
Battery indicator
~
Indicates the battery charge.
Bandwidth
Indicator
Indicates that the RBW or VBW
settings are in manual mode.
Status Icon Overview
24
GETTING STARTED
Average
Indicates that the Average function
is active.
External Lock
Indicates that the system is now
locked and refers to the external
reference input signal
External Trigger
External trigger signal is being
used.
Math
Trace math is being used.
Sequence
Indicator
Shown when a sequence is running.
Sweep Indicator
Indicates that the sweep time is
manually set.
Tracking
generator
Indicates that the tracking generator
is turned on.
TG Normalization
Indicates that the tracking generator
has been normalized.
Wake-up clock
Indicates that the wake-up clock is
turned on.
USB
Indicates that a USB flash drive is
inserted into the front panel and is
recognized.
Micro SD
Indicates that a micro SD card is
inserted into the front panel and is
recognized.
25
GSP-9330 User Manual
Description
The GSP-9330 has two adjustable rubber feet
that can used to position the instrument into
two preset orientations.
Upright Position
Tuck the feet under
the bottom of the
instrument to stand
the instrument
upright.
Leaning Position
Pull the feet back to
have the instrument
leaning back.
First Use Instructions
Use the procedures below when first using the GSP-9330 to tilt the
stand, insert the battery pack, power up the instrument, set the
internal clock, set the wake-up clock, update the firmware and to
restore the default settings. Lastly, the Conventions sections will
introduce you to the basic operating conventions used throughout
the user manual.
Tilting the Stand
26
GETTING STARTED
Description
The GSP-9330 has an optional battery pack.
The battery should be inserted before power is
connected to the AC power socket and before
the unit is turned on.
Steps
1. Ensure the power is off and the AC power is
disconnected.
2. Remove the battery cover.
3. Insert the battery as shown in the diagram
below.
4. Replace the battery cover.
Display Icon
The battery icon is displayed when GSP9330 is running on battery power.
Insertion Diagram
Inserting the Battery Pack
27
Power UP
Steps
1. Insert the AC power cord into the power
socket.
2. The power button exterior will be lit blue to
indicate that the GSP-9330 is in standby mode.
3. Press the power button for a few seconds to
turn the GSP-9330 on.
4. The power button will turn orange and the
GSP-9330 will start to boot up.
Note
It takes a little less than 1 minute for the GSP-9330
to fully startup.
GSP-9330 User Manual
28
Loading...
+ 317 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.