Guild SS20G22OW Instruction manual

210x148mm
Corded 1000 Lumen | 16W 220-240V Led Worklight
Original Instruction Manual
1000
Important
These instructions contain important information that will help you get the best from your worklight, ensuring it is operated correctly and safely. If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800.Please visit the website www.argos.co.uk for more information.
Argos Limited 489-499 Avebury Boulevard, Saxon Gate West, Central Milton Keynes, MK9 2NW
40 m
- Please read these instructions fully before starting operating
Model No.SS20G22OW
After Sales Support
UK/Ireland 03456 400800
Web WWW.ARGOS.CO.UK
Contents
Saftey Information ..............................................................................................
In The Box...........................................................................................................
Operating Instructions.........................................................................................
Environmental Protection....................................................................................
Guarantee ........................................................................................................
Customer Helpline 03456 400800 Customer Helpline 03456 400800 Customer Helpline 03456 400800 Customer Helpline 03456 400800
Safety Information In The Box
2
3
3
4
4
1 2 3 4
READ AND UNDERSTAND ALL SAFETY AND OPERATING INSTRUCTIONS IN THIS MANUAL BEFORE USING THIS PRODUCT.
WARNING Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
BE EXTREMELY CAREFUL WHEN USING THIS DEVICE. Improper use of this workight can result in injury or death. Follow all safeguards stated in this manual in addition to normal safety precautions in working with electrical devices. DO NOT attempt to service this device.
-When using portable worklights, always follow basic safety precautions to reduce the risk of electric shock and personal injury.
-Failure to observe the following safety rules may result in FIRE, ELECTRICAL SHOCK, INJURY, or EXPOSURE TO EXCESSIVE ULTRAVIOLET RADIATION.
-To avoid electrical shock, do not use with extension cord near water or where water may accumulate. Keep worklight at least 5M from pools and spas. Keep plugs and receptacles dry. Use only Ground Fault Circuit Interrupter (GFCI) protected receptacles when using this worklight in wet or damp locations. Receptacles are available with built-in GFCI protection and are to be used for this measure of safety.
-To avoid burns, do not touch the lens or metal part of the lamp head while lamp is turned on.
-Do not look directly at the lighted lamps to avoid eye injuries.
-Always keep the worklight away from any flammable surfaces or materials.
-Unplug from outlet before servicing or cleaning. This will reduce the risk of electric shock.
-DO NOT store or use the light in locations where the temperature may reach or exceed 45°C.
-Risk of burns, do not operate without guard.
-The worklight should be located no further than 1.5m from the nearest outlet.
-Keep out of reach of children.
-Do not operate worklight if it has a missing or damaged lens cover. Contact customer service for a replacement. Read and follow all safety rules and operating instructions before first use of this product.
PARTS
A
B
C
D
When unpacking the box, do not discard any packaging materials until all of the contents are accounted for:
1. Corded 1000 lumen | 16W 220-240V led worklight
2. Stand “F”
3. Operator’s manual
Carefully lift the worklight out of the box.
DESCRIPTION
Handle
Light Fixture
Screw
U-Shaped Bracket
PARTS DESCRIPTION
E
F
G
Knob
Stand
Switch
Operating Instructions
BULB REPLACEMENT
The LED blub is not designed for replacement, as it is produced for a lifespan of over 20,000 hours. Contact a qualified electrician for further check if the LED bulb failed to work.
ASSEMBLY INSTRUCTIONS
Do not assemble while plugged into power.
1. Locate the worklight housing “B” and the Stand “F”.
2. Remove the knob “E” from stand “F”, position the U-shaped bracket “D” against the stand “F”.
3. Use knob “E” to connet the U-shaped bracket “D” and the stand “F”. Place the washer in between the knob ''E'' and bracket ''D''.
4. Put the worklight on its stand “F” and it’s ready to use.
OPERATION
1. Loosen the screw “C” on side, adjust the lamp to desired position and re-tighten the screw“C”.
2. Always press switch “G” to turn the lamp OFF before unplugging the worklight.
Symbols Used
This appliance conforms to relevant directives of the European Community.
Waste electrical and electronic equipment (WEEE), should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
Protected against solid foreign objects of 1.0 mm Ø and greater. Protected against water drops at 15 degree angle.
Replace any cracked protective shield.
Environmental Protection
Recycling electrical products: You should now recycle your waste electrical goods and in doing so help the environment. This symbol means an electrical product should not be disposed of with normal household waste. Please ensure it is taken to a suitable facility for disposal. Visit www.recycle-more.co.uk click on "bank locator" and enter your postcode to find your nearest recycling site.
Guarantee
This product is guaranteed against manufacturing defects for a period of 24 months. This does not cover the product where the fault is due to misuse, abuse, use in contravention of the instructions, or where the product has been the subject of unauthorised modifications or alterations, or has been the subject of commercial use. In the event of a problem with the product within the guarantee period please return it to your nearest store. If the item is shown to have an inherent defect present at the time of sale, the store will provide you with a replacement. Your statutory rights remain unaffected.
Loading...