GSI PNEG-1810 User Manual
PNEG-1810
Bin Manager Temperature Cable
Support Bracket Instructions
Instruction Manual
PNEG-1810
Date: 04-11-12
2 PNEG-1810 Bin Manager Temperature Cable Support Bracket Instructions
Table of Contents
Contents
Chapter 1 Introduction ..........................................................................................................................................4
Chapter 2 Safety .....................................................................................................................................................5
Safety Guidelines .................................................................................................................................. 5
General Safety Statement ..................................................................................................................... 6
Safety Instructions ..................... ... .... .......................................... ... ... ..................................................... 7
Chapter 3 Decals ....................................................................................................................................................9
Chapter 4 Temperature cable location ...............................................................................................................12
18'-30' Temperature Cable Locations ................................................................................................. 12
33'-36' Temperature Cable Locations ................................................................................................. 13
39'-42' Temperature Cable Locations ................................................................................................. 14
48' Temperature Cable Locations ....................................................................................................... 15
54'-60' Temperature Cable Locations ................................................................................................. 16
Chapter 5 Temperature cable support packages for eave height of less than or equal to 40' 5" ................17
Eave Heights of Less than or Equal to 40' 5" ...................................................................................... 17
18'-30' Temperature Cable Support Assembly for Farm Roofs
with Eave Heights of 40' 5" or Less ..................................................................................................... 18
33'-42' Temperature Cable Support Assembly for Farm Roofs
with Eave Heights of 40' 5" or Less ..................................................................................................... 20
Chapter 6 Temperature cable support system for eave height of less than or equal to 40' 5" ....................23
Eave Heights of Less than or Equal to 40' 5" ...................................................................................... 23
48' Temperature Cable Support Assembly for Farm Roofs
with Eave Heights of 40' 5" or Less ..................................................................................................... 24
24' Temperature Cable Support Assembly for 2 Post Bins
with Farm Roof and No Height Restrictions ........................................................................................ 26
27'-30' Temperature Cable Support Assembly for 2 Post Bins
with Farm Roof and No Height Restrictions ........................................................................................ 29
36' Temperature Cable Support Assembly for 2 Post Bins
with Farm Roof and No Height Restrictions ........................................................................................ 31
Chapter 7 Temperature cable support packages for eave height greater than 40' 5" ...................................33
Eave Heights Greater than 40' 5" ........................................................................................................ 33
27' Temperature Cable Support Assembly for 3 Post Bins
with Farm Roof and No Height Restrictions ........................................................................................ 34
30' Temperature Cable Support Assembly for 3 Post Bins
with Farm Roof and No Height Restrictions ........................................................................................ 36
33' Temperature Cable Support Assembly for 3 Post Bins
with Farm Roof and No Height Restrictions ........................................................................................ 38
36' Temperature Cable Support Assembly for 3 Post Bins
with Farm Roof and No Height Restrictions ........................................................................................ 40
Chapter 8 Temperature cable support packages for commercial roofs .........................................................43
Commercial Roofs ..................... ... .... ... .......................................... ... ... ................................................ 43
39'-48' Temperature Cable Support Assembly for Commercial Roofs and No Height Restrictions .... 44
54'-60' Temperature Cable Support Assembly for Commercial Roofs and No Height Restrictions .... 47
Typical 2 Rib External Mounting of Temperature Cable Bracket ........................................................ 49
Chapter 9 Warranty ..............................................................................................................................................51
PNEG-1810 Bin Manager Temperature Cable Support Bracket Instr uc tio ns 3
1. Introduction
READ THIS MANUAL carefully to learn how to properly use and install equipment. Failure to do so could
result in personal injury or equipment damage.
INSPECT the shipment immediately upon arrival. The customer is responsible for ensuring that all
quantities are correct. The customer should report and note any damage or shortage on the bill of
lading to justify their claim to the transport company.
THIS MANUAL SHOULD BE CONSIDERED a permanent part of your equipment and should be easily
accessible when needed.
This warranty provides you the assurance that the company will back its products when defects appear
within the warranty period. In some circumstances, the company also provides field improvements, often
without charge to the customer, even if the product is out of warranty. Should the equipment be abused,
or modified to change its performance beyond the factory specifications, the warranty will become void
and field improvements may be denied.
4 PNEG-1810 Bin Manager Temperature Cable Support Bracket Instructions
2. Safety
DANGER
WARNING
CAUTION
NOTICE
This is the safety alert symbol. It is used to alert you
to potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible
injury or death.
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION, used with the safety alert symbol, indicates a
hazardous situation which, if not avoided, could result in
minor or moderate injury.
NOTICE is used to address practices not related to
personal injury.
DANGER indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
Safety Guidelines
This manual contains information that is important for you, the owner/operator, to know and understand.
This information relates to protecting personal safety and preventing equipment problems. It is the
responsibility of the owner/operator to inform anyone operating or working in the area of this equipment
of these safety guidelines. To help you recognize this information, we use the symbols that are defined
below. Please read the manual and pay attention to these sections. Failure to read this manual and its
safety instructions is a misuse of the equipment and may lead to serious injury or death.
PNEG-1810 Bin Manager Temperature Cable Support Bracket Instruc tions 5
2. Safety
This product has sharp edges, which may cause serious injury. To avoid injury, handle
sharp edges with caution and always use proper protective clothing and equipment.
General Safety Statement
Our foremost concern is your safety and the safety of others associated with grain handling equipment.
This manual is to help you understand safe operating procedures and some problems that may be
encountered by the operator and other personnel.
As owner and/or operator, you are responsible to know what requirements, hazards, and precautions
exist, and inform all personnel associated with the equipment or in the area. Safety precautions may be
required from the personnel. Avoid any alterations to the equipment, which may produce a very dangerous
situation, where SERIOUS INJURY or DEATH may occur.
You should consider the location of the bin site relative to power line locations or electrical transmission
equipment. Contact your local power company to review your installation plan or for information
concerning required equipment clearance. Clearance of portable equipment that may be taken to the bin
site should also be reviewed and considered. Any electrical control equipment in contact with the bin
should be properly grounded and installed in accordance with National Electric Code provisions and other
local or national codes.
This product is intended for the use of grain storage only. Any other use is a misuse of the product.
Sidewall bundles or sheets must be stored in a safe manner. The safest method of storing sidewall
bundles is laying horizontally with the arch of the sheet upward, like a dome. Sidewall sheets stored on
edge must be secured so that they cannot fall over and cause injury. Use care when handling and moving
sidewall bundles.
Personnel operating or working around equipment should read this manual. This manual must be
delivered with equipment to its owner. Failure to read this manual and its safety instructions is a misuse
of the equipment.
6 PNEG-1810 Bin Manager Temperature Cable Support Bracket Instructions
2. Safety
Follow Safety Instructions
Carefully read all safety messages in this manual and
safety signs on your machine. Keep signs in good
condition. Replace missing or damaged safety signs. Be
sure new equipment components and repair parts include
the current safety signs. Replacement safety signs are
available from the manufacturer.
Learn how to operate the machine and how to use controls
properly. Do not let anyone operate without instruction.
Keep your machinery in proper working condition.
Unauthorized modifications to the machine may impair
the function and/or safety and affect machine life.
If you do not understand any part of this manual or need
assistance, contact your dealer.
Read and Understand Manual
Practice Safe Maintenance
Understand service procedures before doing work. Keep area
clean and dry.
Never lubricate, service, or adjust machine while it is in operation.
Keep hands, feet, and clothing away from rotating parts.
Keep all parts in good condition and properly installed. Fix
damage immediately . Replace worn or broken p arts. Remove any
built-up grease, oil, and debris.
Maintain Equipment
and Work Area
Safety Instructions
Our foremost concern is your safety and the safety of others associated with this equipment. We want to
keep you as a customer. This manual is to help you understand safe operating procedures and some
problems that may be encountered by the operator and other personnel.
As owner and/or operator, it is your responsibility to know what requirements, hazards, and precautions
exist, and to inform all personnel associated with the equipment or in the area. Safety precautions may be
required from the personnel. Avoid any alterations to the equipment. Such alterations may produce a very
dangerous situation where SERIOUS INJURY or DEATH may occur.
This equipment shall be installed in accordance with the current installation codes and applicable
regulations, which should be carefully followed in all cases. Authorities having jurisdiction should be
consulted before installations are made.
PNEG-1810 Bin Manager Temperature Cable Support Bracket Instruc tions 7
2. Safety
Prepare for Emergencies
Be prepared if fire starts.
Keep a first aid kit and fire extinguisher handy.
Keep emergency numbers for doctors, ambulance service,
hospital, and fire department near your telephone.
Keep Emergency Equipment
Quickly Accessible
Wear Protective Clothing
Wear close-fitting clothing and safety equipment appropriate
to the job.
Remove all jewelry.
Tie long hair up and back.
Wear safety glasses at all times to protect eyes from debris.
Wear gloves to protect your hands from sharp edges on
plastic or steel parts.
Wear steel-toed boots to help protect your feet from falling
debris. Tuck in any loose or dangling shoestrings.
A respirator may be needed to prevent breathing potentially
toxic fumes and dust.
Wear a hard hat to help protect your head.
Wear appropriate fall protection equipment when working at
elevations greater than six feet (6').
Eye Protection
Gloves
Steel-Toed Boots
Respirator
Hard Hat
Fall Protection
8 PNEG-1810 Bin Manager Temperature Cable Support Bracket Instructions
3. Decals
The manufacturer does not warrant any roof damage caused by excessive vacuum or internal
pressure from fans or other air moving systems. Adequate ventilation and/or “makeup air” devices
should be provided for all powered air handling systems. The manufacturer does n ot recommend
the use of downward flow systems (suction). Severe roof damage can result fro m any blockage of
air passages. Running fans during high humidity/cold weather conditions can cause air exhaust
or intake ports to freeze.
CAUTION!
Excessive vacuum (or pressure) may
damage roof. Use positive aeration
system. Make sure all roof vents are
open and unobstructed. Start roof
fans when supply fans are started.
Do not operate when conditions exist
that may cause roof vent icing.
DC-969
PNEG-1810 Bin Manager Temperature Cable Support Bracket Instruc tions 9
3. Decals
Rotating flighting will
kill or dismember.
Flowing material will
trap and suffocate.
Crusted material will
collapse and suffocate.
Keep clear of all augers.
DO NOT ENTER this bin!
Failure to heed these
warnings will result in
serious injury or death.
If you must enter the bin:
1. Shut off and lock out all power.
2. Use a safety harness and safety line.
3. Station another person outside the bin.
4. Avoid the center of the bin.
5. Wear proper breathing equipment or respirator.
DC-GBC-1A
ATTENTION: The decal shown below should be present on the outside of the door cover of the 2 ring,
24" porthole door cover and roof manway cover. If a decal has been damaged or is missing in any of these
locations, contact the manufacturer for a free replacement decal.
GSI Decals
1004 E. Illinois St.
Assumption, IL. 62510
Phone: 1-217-226-4421
10 PNEG-1810 Bin Manager Temperature Cable Support Bracket Instructions
3. Decals
ATTENTION: The decal shown below should be present on the outside of the door cover of the 2 ring,
24" porthole door cover and roof manway cover. If a decal has been damaged or is missing in any of these
locations, contact the manufacturer for a free replacement decal.
GSI Decals
1004 E. Illinois St.
Assumption, IL. 62510
Phone: 1-217-226-4421
WARNING
DON’T
DO
UNLOADING INSTRUCTIONS:
1. Use CENTER FLOOR OUTLET ONLY until NO grain
remains above this outlet.
2. Side floor outlets to be used ONLY when above
condition is satisfied.
3. Lock all side floor outlets to avoid accidental
premature use.
4. See manufacturers instructions for proper use of
factory supplied sidedraw (wall) discharge systems.
Failure to heed these warnings
could result in serious injury, death,
structural damage or collapse of tank.
DC-GBC-2A
PNEG-1810 Bin Manager Temperature Cable Support Bracket Instruc tions 11
4. Temperature cable location
18'-30' Temperature Cable Locations
Figure 4A
12 PNEG-1810 Bin Manager Temperature Cable Support Bracket Instructions
33'-36' Temperature Cable Locations
4. Temperature cable location
Figure 4B
PNEG-1810 Bin Manager Temperature Cable Support Bracket Instruc tions 13
4. Temperature cable location
39'-42' Temperature Cable Locations
Figure 4C
14 PNEG-1810 Bin Manager Temperature Cable Support Bracket Instructions
48' Temperature Cable Locations
4. Temperature cable location
Figure 4D
PNEG-1810 Bin Manager Temperature Cable Support Bracket Instruc tions 15
4. Temperature cable location
54'-60' Temperature Cable Locations
Figure 4E
16 PNEG-1810 Bin Manager Temperature Cable Support Bracket Instructions
Loading...