Grundig GCA-B3323V, GCA-B3326V, GCA-B3322D, GCA-B3326D Owner's Manual

GCA-B3323V.42.1.09.02.2012

Owner's Manual

EN

© ASP AG

Cameras & Domes

GCA-B3323V 1/3" CCD Col/B&W Fixed Dome Camera
GCA-B3326V 1/3" CCD Col/B&W Fixed Dome Camera w/ IR LED

Content:

1. Available Versions
2

2. Important Safety Instructions
2

3. Package Co

ntents

3

4. Installation
3

1. Part Names 4

2. Base Installation 5

3. Mounting Housings to Electrical Junction Boxes 6

4. Connections 7

5. 3-Axis Gimbal Adjustment 7

6. Zoom & Focus Adjustment 8

7. IR-LED On/Off Switch 8

8. Fan & Heater (optional) 9

5. OSD Control Keys
9

6. OSD Menu

10

1. LENS 11

2. SHUTTER/ AGC 12

3. WHITE BAL (White Balance) 13

4. PICT ADJUST (Picture Adjustment) 15

5. NR (Noise Reduction) 16

6. ATR (Adaptive Tone-Curve Reproduction) 16

7. BACKLIGHT 16

8. CAMERA ID 17

9. DAY/NIGHT 17

10. MOTION DET (Motion Detection) 18

11. PRIVACY 19

12. SYNC 20

13. LANGUAGE 20

14. CAMERA RESET 20

15. NEXT / BACK 20

16. EXIT 20

17. SAVE ALL 20

1. Available Versions

These instructions apply to the following products. For the different properties of the
products please refer to the table.

2. Important Safety Instructions

Be sure to use only the standard adapter that is specified in the specification sheet.
Using any other adapter could cause fire, electrical shock, or damage to the product.
Incorrectly connecting the power supply or replacing battery may cause explosion, fire,
electric shock, or damage to the product. Do not connect multiple products to one single
adapter. Exceeding the capacity may cause abnormal heat generation or fire.

Do not place conductive objects (e.g. screwdrivers, coins or any metal items) or
containers filled with water on top of the product. Doing so may cause personal injury
due to fire, electric shock, or falling objects.

If any unusual smells or smoke comes out of the unit, stop using the product. In this
case, immediately disconnect the power source and contact the service center.
Continued use in such a condition may cause fire or electric shock.

If this product fails to operate normally, contact the nearest service center. Never
disassemble or modify this product in any way. (GRUNDIG is not liable for problems
caused by unauthorised modifications or attempted repair.)

To prevent fire or electric shock, do not expose the inside of this device to rain or
moisture.

2

English

3. Package Contents

These parts are included:

- Torx Wrench: Length 90mm (1pc)

- Dowel: Length 30mm, Thickness 6mm (4pcs)

- Assembly Screws: FH M4x14 (4pcs)

- Mounting Screws: ST4x38 (4pcs)

These screws are used to mount both surface mount plate or flush mount base to a
sturdy surface. If necessary, use the dowels included.

- Pipe Cap Driver: (1pc)

This is used to open/close the pipe cap of the surface mount plate.

- Service monitor and control cable:

It is possible to set up the camera through a portable monitor and adjust the OSD menu
of the camera externally.

4. Installation

Do not install the product in a location subject to high temperature (over 50°C), low
temperature (below -10°C), or high humidity. Doing so may cause fire or electric shock.
Keep out of direct sunlight and heat radiation sources. This may cause fire. Avoid aiming
the camera directly towards extremely bright objects such as the sun, as this may
damage the image sensor.

Do not install the unit in humid, dusty or sooty locations. Doing so may cause fire or
electric shock. Install it in a place with good ventilation.

3

English

When installing the unit, fasten it securely and firmly. A falling unit may cause personal
injury.

If you want to relocate the already installed product, be sure to turn the power off and
then move or reinstall it.

4.1. Part Names

1. Bubble

2. Dome Cover Ring

3. Lens

4. Safety Wire

5. Service Monitor Output Port

6. Flush Mount Base

7. Surface Mount Plate

8. Assembly Screws (Torx M4x8)

9. Assembly Screws (Philips M4x14)

10. Gimbal Bracket

11. Mounting Screws (St4x38)

12. Video/Power Cable

Caution:
To avoid smear, do not expose the camera directly to a strong light source such as the
sun or spot light.

4

English

4.2. Base Installation

1. Remove the dome cover by loosening the 3 screws. Use the Torx wrench supplied.

2. Surface Mount :

Using the four ST4x38 screws, mount the surface plate to a sturdy surface.
Using the four M4x14 screws, affix the flush mount base to a surface plate.
(For flush mount application, disregard section 2.)

3. Flush Mount :

Using the four ST4x38screws, affix the flush mount base to a sturdy surface.

5English

4.3. Mounting Housings to Electrical Junction Boxes

This unit can be either flush mounted or surface mounted with Electrical Junction Boxes
using the pre-drilled mounting holes. The dome housing accommodates various
electrical junction boxes, making the installation easy and less time consuming.

NOTE:
The screws required for electrical junction boxes are not supplied with the Dome. These
screws are readily available at local electrical supply stores.

6

English