COPYRIGHT © 1999 BY GRIZZLY INDUSTRIAL, INC.
1821 VALENCIA ST., BELLINGHAM, WA 98227
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
NOVEMBER, 1999 PRINTED IN U.S.A.
WWW.GRIZZLY.COM
3.6V CORDLESS SCREWDRIVER
AND FLASHLIGHT KIT
MODEL G8592
INSTRUCTION MANUAL
G8592 3.6V Cordless Screwdriver/Flashlight -3-
SAFETY
For Your Own Safety Read Instruction Manual
Before Operating This Equipment
Indicates an imminently hazardous situation which, if
not avoided, WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, COULD
result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, MAY
result in minor or moderate injury.
It may also be used to alert against unsafe practices.
This symbol is used to alert the user to useful information
about proper operation of the equipment.
The purpose of safety symbols is to attract your attention to possible hazardous
conditions. This manual uses a series of symbols and signal words which are
intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
NOTICE
Safety Instructions For Power Tools
5. KEEP CHILDREN AND VISITORS
AWAY. All children and visitors
should be kept a safe distance from
work area.
6. MAKE WORK SHOP CHILD
PROOF with padlocks, master
switches, or by removing starter
keys.
7. DON’T FORCE TOOL. It will do the
job better and safer at the rate for
which it was designed.
8. USE RIGHT TOOL. Don’t force tool
or attachment to do a job for which it
was not designed.
1. KEEP ALL SAFETY DEVICES IN
PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of check-
ing to see that keys and adjusting
wrenches are removed from tool
before turning on.
3. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite
accidents.
4. DON’T USE IN DANGEROUS
ENVIRONMENT. Don’t use power
tools in damp or wet locations, or
where any flammable or noxious
fumes may exist. Keep work area
well lighted.
G8592 3.6V Cordless Screwdriver/Flashlight-4-
9. USE PROPER EXTENSION CORD
for the charger. Make sure your
extension cord is in good condition.
Conductor size should be in accordance with the chart below. The
amperage rating should be listed on
the motor or tool nameplate. An
undersized cord will cause a drop in
line voltage resulting in loss of power
and overheating. Your extension
cord must also contain a ground wire
and plug pin. Always repair or
replace extension cords if they
become damaged.
Minimum Gauge for Extension Cords
10. WEAR PROPER APPAREL. Do not
wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving
parts. Non-slip footwear is recommended. Wear protective hair covering to contain long hair.
11. ALWAYS USE SAFETY GLASSES.
Also use face or dust mask if cutting
operation is dusty. Everyday eyeglasses only have impact resistant
lenses, they are NOT safety glasses.
12. SECURE WORK. Use clamps or a
vise to hold work when practical. It’s
safer than using your hand and frees
both hands to operate tool.
Safety Instructions For Power Tools
AMP LENGTH
RATING 25ft 50ft 100ft
0-6 18 16 16
7-10 18 16 14
11-12 16 16 14
13-16 14 12 12
17-20 12 12 10
21-30 10 10 No
13. DON’T OVERREACH. Keep prop-
er footing and balance at all times.
14. MAINTAIN TOOLS WITH CARE.
Keep tools sharp and clean for
best and safest performance.
Follow instructions for lubricating
and changing accessories.
15. DISCONNECT TOOLSbefore ser-
vicing and changing accessories,
such as blades, bits, cutters, and
the like.
16. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make
sure switch is in off position before
plugging in.
17. USE RECOMMENDED ACCESSORIES. Consult the owner’s
manual for recommended accessories. The use of improper accessories may cause risk of injury.
18. CHECK DAMAGED PARTS.
Before further use of the tool, a
guard or other part that is damaged should be carefully checked
to determine that it will operate
properly and perform its intended
function. Check for alignment of
moving parts, binding of moving
parts, breakage of parts, mounting, and any other conditions that
may affect its operation. A guard or
other part that is damaged should
be properly repaired or replaced.
19. NEVER LEAVE TOOL RUNNING
UNATTENDED. TURN POWER
OFF. Don’t leave tool until it comes
to a complete stop.
G8592 3.6V Cordless Screwdriver/Flashlight -5-
CHARGING SAFETY
1. READ ALL INSTRUCTIONS and
warnings on the battery and charger before charging the battery.
2. CHARGE ONLY USING THE SUPPLIED CHARGER AND BATTERY. Do not use with other batter-
ies, chargers or cordless equipment.
3. DO NOT EXPOSE BATTERY OR
CHARGER TO WET OR RAINY
CONDITIONS. Moisture greatly
increases the risk of a shock hazard.
4. DO NOT TOUCH BATTERY
POLES with any conductive materi-
als. Touching any two poles at the
same time causes a short condition
and can cause sparks, electrical
shock or fire.
5. DO NOT STORE BATTERY WITH
CONDUCTIVE MATERIALS.
Storing the battery in a box of
screws or nails can cause shorting
across the battery poles.
6. DO NOT THROW BATTERY IN
FIRE. Combustion of some of the
batteries’ component materials can
cause toxic fumes and possible
explosion.
7. IF CHARGER LIGHT FAILS TO
COME ON check the incoming
power supply. If power source is
okay, then the fuse inside the
charger needs replacement.
Charger should be serviced by a
qualified electrical technician only.
8. CHARGER HAS A POLARIZED
PLUG (one prong is wider than the
other). Do not attempt to modify the
plug. Modifying the plug will result
in a safety hazard and will void the
warranty.
9. CHARGER IS DESIGNED TO
OPERATE AT 110-120 VOLTS.
Never try to plug into any circuit that
is not 110-120 volts. Never modify
or change the plug that is attached
to the charger unit to attempt to
plug into 220 volt. This can cause
serious electrical damage to the
unit, possible fire or explosion.
BATTERY MUST BE RECYCLED
OR DISPOSED OF PROPERLY.
Consult your local Yellow Pages directory under the category “Recycling” to
locate a battery recycler in your area.
G8592 3.6V Cordless Screwdriver/Flashlight-6-
BEFORE YOU START
Unpacking
When unpacking, check to make sure all
of the following parts are included:
1 Cordless Screwdriver w/ Battery
1 Cordless Flashlight w/ Battery
1 Charging Adapter
1 Bit Extension
1 Square Drive Adapter
1 Double End Phillips®/Straight Bit
8Sockets (6mm - 13mm)
4 Straight Blade Screwdriver Bits
4 Phillips®Screwdriver Bits
4 Posi-Drive®Driver Bits
8 Torx®Driver Bits
8 Hex Driver Bits
If any parts are missing, please contact
Grizzly’s Customer Service department at
the phone number provided on the
Warranty/Returns page.
the storage capacity of the battery it should
be completely discharged (turn the flashlight and screwdriver on and let them run
until the batteries discharge), then fully
recharge for 10-12 hours.
For optimal life span, completely discharge
the battery after every use. Follow the
instructions below to charge your battery
NOTE: The battery does not need to be
removed from the tool in order to be
charged.
1. Plug the adapter into an appropriate
110/120V outlet.
2. Plug the other end of wire with the pin
plug into the receptacle on the base
of the Screwdriver or Flashlight battery pack (See Figure 2).
3. Let the battery charge for 10-12
hours. This will give the battery a full
charge. DO NOT let the battery
charge for more than 12 hours.
4. When charging is complete, unplug
the pin plug from the battery pack,
and unplug the adapter from the wall
outlet. The accessory should be
ready to use.
Fig 2. Plugging charger into battery.
Fig 1. Kit Contents (case not shown).
Initial Charging
The batteries in your new Cordless
Screwdriver/Flashlight Kit will not be fully
charged when you receive it. To maximize
G8592 3.6V Cordless Screwdriver/Flashlight -7-
OPERATION
Inserting and Removing
Drivers and Sockets:
The hex end of the screwdriver bits fit into
the hex opening on the end of the cordless
driver. The bits can be inserted directly into
the tool, or if additional extension is
required, you can insert the bit extender
first, then mount the bit on the end of the
extension (See Figure 3).
When using the supplied sockets you will
need to use the square drive adapter
which is included. You can easily distinguish this from the other drivers by the
spring loaded detent ball on the square
end. This helps to lock the socket into
place on the end of the driver. Attach the
socket to the adapter, then insert the
adapter into the end of the driver tool.
Torque Setting
Turn the torque setting dial to the desired
torque setting (See Figure 3). Line up the
number on the torque dial with the small
arrow embossed on the left hand side of
the case. Torque setting “1” has the highest torque, setting “6” the least. Use only
the necessary amount of torque to avoid
damaging the material you are driving into
or the tool.
The driver has a maximum speed of 150
RPM.
Fig 3. Using bit extension.
Torque Setting Dial
G8592 3.6V Cordless Screwdriver/Flashlight-8-
OPERATION
Operating this equipment has the
potential to propel debris into the air
which can cause eye injury. Always
wear safety glasses or goggles when
operating equipment. Be certain the
safety glasses you wear meet the
appropriate standards of the
American National Standards
Institute (ANSI).
Fig 4. Positioning the handle and switch
location.
Removing Battery From Tool
The battery can be removed by pressing
on the two circular depressions at the end
of the handle and pulling away from the
tool. When reinstalling the battery, be sure
the elongated end of the battery is aligned
with the slots on the inside of the compartment. The battery will lock into position
when fully inserted.
Handle Position and Switch
The driver and flashlight are both jointed in
the center to adjust to different types of
use. Adjust the angle to whatever is comfortable for the job to be done (See Figure
4.)
The driver has a two position rocker switch
with forward and reverse. If you want to
tighten a screw, push on the top of the
switch to drive clockwise. To operate
counterclockwise, push the bottom portion
of the switch.
There is also a locking switch just above
the forward/reverse switch. This allows
you to lock the tool to prevent accidental
use of the tool. You should always use the
LOCK position when placing, removing or
adjusting bits or when removing the battery.
The flashlight has only a slider ON/Off
switch on the top of the case.
Fwd/Rev Switch
Lock Switch
G8592 3.6V Cordless Screwdriver/Flashlight -9-
Maintenance
Your cordless power tool will give you hundreds of hours of operation time before
ever needing service. The electrical components of this cordless drill are not user
serviceable. Repair should always be
undertaken by a qualified electrical repair
technician.
Keep the drill free from dirt and grease.
Always store it in a dry place, preferably in
the case that is supplied.
The battery will require periodic recharging, and eventually replacement after it has
exceeded its recharge life (approximately
800-1000 recharge cycles). You will notice
extended charging times or shortened
operation time as the battery experiences
more cycles. Battery must be recycled or
disposed of properly. Refer to the Grizzly
catalog for replacement batteries.
OPERATING TIPS AND MAINTENANCE
Disassembly and improper reassembly of this device can result in electrical shock danger. Always have this
device serviced by an qualified electrical repair technician. Serious injury
will result.
Operating Guides and Tips
Avoid overloading the driver. Always
use a driver which matches the fastener you are trying to drive. Do not
apply excessive pressure to the driver while using. If the speed drops
abnormally, decrease pressure
immediately. If the driver stops
abruptly or becomes blocked,
release the switch at once.
Ensure the safety of the workplace.
Clear the work area of all parts and
debris that may cause injury by flying
objects. Securely fix the object to be
fastened in a vise or otherwise clamp
to avoid injury. Do not attempt to hold
workpiece by hand.
Inspect the driver before use. Run the
driver before using to ensure all parts
are running smoothly and there are
no abnormal sounds or sparks. If any
defect is found, have unit serviced.
Know your worksite. Before driving fas-
teners, check behind walls for wires,
other electrical hazards, or plumbing.
Use accessories properly. Use the low-
est possible torque setting when driving fasteners. This will increase the
life span of the driving bit and prevent damage to the fastener.
G8592 3.6V Cordless Screwdriver/Flashlight-10-
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original
purchaser from the date of purchase. This warranty does not apply to defects due directly
or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty and any and all warranties that may be
implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent that the
merchandise complies with the provisions of any law or acts unless the manufacturer so
warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price
paid for the product and any legal actions brought against Grizzly shall be tried in the State
of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details.
We will then issue you a “Return Number’’, which must be clearly posted on the outside as
well as the inside of the carton. We will not accept any item back without this number. Proof
of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to achieve better quality equipment. We make every effort to ensure that our
products meet high quality and durability standards and we hope you never need to use this
warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail:
techsupport@grizzly.com
Web Site: http://www.grizzly.com
Thank you again for your business and continued support. We hope to serve you again
soon.
WARRANTY AND RETURNS
G8592 3.6V Cordless Screwdriver/Flashlight -11-
Name__________________________________________________________
Street__________________________________________________________
City____________________State________Zip_________
Phone Number____________E-Mail___________________FAX____________
MODEL # G8592 3.6V Cordless Set Order #_______________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help
us develop better products and services. Of course, all information is strictly confidential.
WARRANTY CARD
9. How many of the machines checked above are
Grizzly? ____________
10. Which portable/hand held power tools do you own?
Check all that apply.
___Belt Sander ___Orbital Sander
___Biscuit Joiner ___Palm Sander
___Circular Saw ___Portable Planer
___Detail Sander ___Saber Saw
___Drill/Driver ___Reciprocating Saw
___Miter Saw ___Router
___Other_________________________________
11. What machines/supplies would you like Grizzly
Industrial to carry?
___12" Table Saw ___Radial Arm Saw
___12" Jointer ___Panel Saw
___Brass Hardware ___Lumber
___Paint & Finishing Supplies
___Contractor’s Supplies
___Combination Planer/Jointer
___Other_________________________________
12. What new accessories would you like Grizzly
Industrial to carry?
___Builders Hardware ___Hand Tools
___Fasteners
___Wood Components
___Other_________________________________
13. What other companies do you purchase your tools
and supplies from?
_________________________________________
_________________________________________
_________________________________________
14. Do you think your purchase represents good value?
___Yes ___No
15. Would you recommend Grizzly to a friend?
___Yes ___No
16. Would you allow us to use your name as a reference for Grizzly customers in your area? Note: We
never use names more than three times.
___Yes ___No
17.Comments:________________________________
_________________________________________
_________________________________________
_________________________________________
1. How did you learn about us?
___Advertisement ___Friend
___Catalog ___Card Deck
___World Wide Web
___Other__________________________
2. What is your annual household income?
___$20,000-$29,999 ___$60,000-$69,999
___$30,000-$39,999 ___$70,000-$79,999
___$40,000-$49,999 ___$80,000-$89,999
___$50,000-$59,999 ___$90,000 +
3. What is your age group?
___20-29 ___50-59
___30-39 ___60-69
___40-49 ___70 +
4. How long have you been a woodworker?
___0 - 2 Years ___8 - 20 Years
___2 - 8 Years ___20+ Years
5. How would you rank your woodworking skills?
___Simple ___Advanced
___Intermediate ___Master Craftsman
6. What stationary woodworking tools do you own?
Check all that apply.
___Air Compressor ___Panel Saw
___Band Saw ___Planer
___Drill Press ___Power Feeder
___Drum Sander ___Radial Arm Saw
___Dust Collector ___Shaper
___Spindle Sander ___Jointer
___Table Saw ___Lathe
___Mortiser ___Wide Belt Sander
___Horiz.Boring Machine
___Vacuum Veneer Press
___Other______________________________
7. How many of your woodworking machines are
Grizzly? _____________
8. Which benchtop tools do you own? Check all
that apply.
___1"x42" Belt Sander ___6" - 8" Grinder
___5" - 8" Drill Press ___Mini Lathe
___8" Table Saw ___8" - 10" Bandsaw
___Scroll Saw ___Disc/Belt Sander
___Spindle/Belt Sander ___Mini Jointer
___10"-12"Thickness Planer
___Other______________________________
G8592 3.6V Cordless Screwdriver/Flashlight-12-
FOLD ALONG DOTTED LINE
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Name________________________________
Street________________________________
City______________State______Zip_______
Send a Grizzly Catalog to a friend:
Loading...