Grizzly G0814X, G0814 User guide

MODEL G0814/G0814X

6" JOINTER w/STAND

OWNER'S MANUAL

(For models manufactured since 12/22)

COPYRIGHT © MARCH, 2016 BY GRIZZLY INDUSTRIAL, INC., REVISED JANUARY, 2023 (KS)

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#BL18046 PRINTED IN TAIWAN

***Keep for Future Reference***

V4.01.23

This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.

Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.

The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and compre­hension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.

The manufacturer will not be held liable for injury or property damage
from negligence, improper training, machine modifications or misuse.

Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State
of California to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks, cement and other masonry products.

• Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equip­ment, such as those dust masks that are specially designed to filter
out microscopic particles.

Table of Contents

INTRODUCTION ............................................... 2

Contact Info
Machine Differences
Manual Accuracy
Identification
Controls & Components
G0814 Machine Data Sheet
G0814X Machine Data Sheet

SECTION 1: SAFETY

Safety Instructions for Machinery
Additional Safety for Jointers

SECTION 2: POWER SUPPLY

Voltage Conversion to 220V

SECTION 3: SETUP

Needed for Setup
Unpacking
Inventory
Hardware Recognition Chart
Cleanup
Site Considerations
Assembly
Dust Collection
Test Run
Recommended Adjustments

SECTION 4: OPERATIONS

Operation Overview
Stock Inspection & Requirements
Setting Depth of Cut
Squaring Stock
Surface Planing
Edge Jointing
Bevel Cutting
Rabbet Cutting

................................................... 2

...................................... 2

........................................... 2

................................................... 3

................................. 4

.......................... 6

........................ 8

..................................... 10

................ 10

....................... 12

...................... 13

........................ 15

....................................... 16

......................................... 16

.................................................... 16

...................................................... 17

....................... 18

........................................................ 19

...................................... 20

..................................................... 21

............................................. 25

....................................................... 26

........................ 26

............................ 27

..................................... 27

............... 28

.................................... 29

............................................ 30

........................................... 31

............................................... 32

............................................... 33

............................................. 34

SECTION 5: ACCESSORIES

SECTION 6: MAINTENANCE

Schedule
Cleaning & Protecting
Lubrication

SECTION 7: SERVICE

Troubleshooting
Setting/Replacing Knives (G0814)
Rotating/Replacing Helical Cutterhead
Inserts (G0814X)
Setting Outfeed Table Height
Calibrating Depth Scale
Adjusting Gibs
Setting Fence Stops
Tensioning/Replacing V-Belt
Aligning Pulleys
Checking/Adjusting Table Parallelism
Checking/Adjusting Cutterhead Guard

SECTION 8: WIRING

Wiring Safety Instructions
110V Wiring Diagram
220V Wiring Diagram

SECTION 9: PARTS

Table
Fence
Cutterhead
Stand
Labels & Cosmetics

WARRANTY & RETURNS

...................................................... 38

................................................... 39

................................... 40

........................................... 40

......................................... 44

.............................................. 48

.................................... 49

........................................... 51

...................................... 55

....................................... 58

............................................................ 58

........................................................... 60

.................................................. 61

............................................................ 62

..................................... 64

......................... 36

......................... 38

.................................. 38

................. 42

....................... 46

............................... 47

........................ 50

.......... 52

........ 53

............................ 55

................................... 56

................................... 57

.............................. 65

We stand behind our machines! If you have ques­tions or need help, contact us with the information
below. Before contacting, make sure you get the

serial number

from the

machine ID label. This will help us help you faster.

We want your feedback on this manual. What did
you like about it? Where could it be improved?
Please take a few minutes to give us feedback.

Email: [e-mail]

We are proud to provide a high-quality owner’s
manual with your new machine!

We

instruc­tions, specifications, drawings, and photographs
in this manual. Sometimes we make mistakes, but
our policy of continuous improvement also means
that

you receive is

slightly different than shown in the manual

If you find this to be the case, and the difference
between the manual and machine leaves you
confused or unsure about something

check our

website for an updated version. W

current

manuals and

on our web-

site at

Alternatively, you can call our Technical Support
for help. Before calling, make sure you write
down the

serial number

from the machine ID label (see below). This
information is required for us to provide proper
tech support, and it helps us determine if updated
documentation is available for your machine.

INTRODUCTION

Contact Info

and manufacture date

Grizzly Technical Support

1815 W. Battlefield

Springfield, MO 65807

Phone: [phone]

Email: [e-mail]

Grizzly Documentation Manager

P.O. Box 2069

Bellingham, WA 98227-2069

Manual Accuracy

made every effort to be exact with the

sometimes the machine

.

,

e post

manual updates for free

www.grizzly.com.

manufacture date and

Machine Differences

Models G0814 and G0814X are 1 HP, 6" jointers
with the following difference:

• Model G0814 has a 3-knife cutterhead.

• Model G0814X has a V-helical cutterhead

with 4 rows and 26 indexable carbide inserts.

Manufacture Date

Serial Number

-2-

Model G0814/G0814X (Mfd. Since 12/22)

Identification

Become familiar with the names and locations of the controls and features shown below to better understand
the instructions in this manual.

M

O

A

N

B

C

D

E

I

J

K

L

F

H

G

A. Outfeed Table
B. Fence
C. Cutterhead Guard
D. Fence Lock
E. Fence Tilt Handle
F. Infeed Table
G. Infeed Table Lever

Fence Tilt Lock

H.

I. Depth Scale

Infeed Table Lock

J.
K. ON/OFF Paddle Switch w/Disabling Key
L. Foot Pedal Caster Assembly
M. Dust Port
N. Outfeed Table Lock

Outfeed Table Handwheel

O.

For Your Own Safety Read Instruction Manual Before Operating Jointer

a) Wear eye protection.
b) Always keep cutterhead and drive guards in place and in proper operating condition. ALWAYS

replace cutterhead guard after rabbeting operations.
c) Never make jointing or rabbeting cuts deeper than
d) Always use hold-down or push blocks when jointing material narrower than 3" or surface

planing material thinner than 3".
e) Never perform jointing, planing, or rabbeting cuts on pieces shorter than 8" in length.

1

⁄8" or planing cuts deeper than 1⁄16".

Model G0814/G0814X (Mfd. Since 12/22)

-3-

Controls &

To reduce your risk of
serious injury, read this
entire manual BEFORE

Components

G

B

C

D

using machine.

Refer to Figures 1–4 and the following descrip­tions to become familiar with the basic controls
and components of this machine. Understanding
these items and how they work will help you
understand the rest of the manual and stay safe
when operating this machine.

A

F

E

Figure 2. Main table controls, fence, and foot

pedal caster.

B. Fence: Guides workpiece as it moves across

cutterhead; determines angle of cut.

C. Fence Tilt Handle: Tilts fence throughout its

range of motion from 45° inward to 45° out­ward (135°).

D. Infeed Table: Supports workpiece before it

reaches cutterhead. Position of infeed table
relative to cutterhead determines depth of
cut.

E. Infeed Table Adjustment Lever: Adjusts

position of infeed table (when infeed table
lock is loosened).

Figure 1. ON/OFF paddle switch location.

A. ON/OFF Paddle Switch w/Disabling Key:

Turns motor ON and OFF. Remove yellow
key to disable switch.

-4-

F. Infeed Table Lock: Loosens to allow adjust-

ment of infeed table height or cutting depth;
tightens to secure infeed table.

G. Outfeed Table: Supports workpiece after

it passes over cutterhead. For safety and
best results, outfeed table must be properly
adjusted relative to cutterhead knives/inserts
before ANY operations (refer to Page 46 for
more details).

Model G0814/G0814X (Mfd. Since 12/22)

H

L

K

I

J

Figure 3. Cutterhead guard and depth-of-cut

scale.

H. Cutterhead Guard: Covers cutterhead

until pushed out of the way by workpiece
during operation. When workpiece leaves
cutterhead, guard springs back to its starting
position.

I. Depth-of-Cut Scale: Indicates cutting depth

of a single pass.

J. Outfeed Table Lock: Loosens to allow

adjustment of outfeed table height; tightens
to secure outfeed table.

P

O

Figure 4. Fence controls.

L. 90° Fence Stop: When engaged, stops

fence at 90°.

Note: Even when fence stop bolt contacts

swing stop, tilt lock must be tightened before
starting machine.

Note: Swing stop must be disengaged for

bevel cuts greater than 90°.

M. 45° Fence Stop: Stops fence at 45° outward

(135°).

M

N

K. Outfeed Table Handwheel: Adjusts position

of outfeed table. Typically only used when set­ting outfeed table even with cutterhead knives/
inserts or when servicing the cutterhead.

Note: Even when fence is resting against

stops, tilt lock must be tightened before start­ing machine.

N. Fence Tilt Lock: Secures fence tilt setting at

desired angle.

O. Fence Lock: Loosens to allow adjustment of

fence position along width of tables. Tightens
to secure fence.

P. Swing Stop: When engaged, stops fence

at 90°. When disengaged, allows fence to
adjust for bevel cuts.

Model G0814/G0814X (Mfd. Since 12/22)

-5-

MACHINE DATA

SHEET

Customer Service #: [phone] · To Order Call: [phone] · Fax #: [phone]

MODEL G0814 6" X 48" JOINTER WITH CABINET STAND

Product Dimensions:

Weight.............................................................................................................................................................. 245 lbs.

Width (side-to-side) x Depth (front-to-back) x Height..................................................................... 47-1/2 x 20 x 42 in.

Footprint (Length x Width)..................................................................................................................... 13-1/2 x 18 in.

Shipping Dimensions:

Carton #1

Type........................................................................................................................................... Cardboard Box

Content................................................................................................................................................. Machine

Weight.................................................................................................................................................... 183 lbs.

Length x Width x Height............................................................................................................. 49 x 22 x 13 in.

Must Ship Upright......................................................................................................................................... Yes

Carton #2

Type........................................................................................................................................... Cardboard Box

Content...................................................................................................................................................... Stand

Weight...................................................................................................................................................... 77 lbs.

Length x Width x Height............................................................................................................. 21 x 17 x 30 in.

Must Ship Upright.......................................................................................................................................... No

Electrical:

Power Requirement............................................................................................. 110V or 220V, Single-Phase, 60 Hz

Prewired Voltage.................................................................................................................................................. 110V

Full-Load Current Rating....................................................................................................... 14A at 110V, 7A at 220V

Minimum Circuit Size.......................................................................................................... 20A at 110V, 15A at 220V

Connection Type....................................................................................................................................... Cord & Plug

Power Cord Included.............................................................................................................................................. Yes

Power Cord Length................................................................................................................................................. 6 ft.

Power Cord Gauge......................................................................................................................................... 16 AWG

Plug Included.......................................................................................................................................................... Yes

Included Plug Type................................................................................................................................. 5-15 for 110V

Recommended Plug Type...................................................................................................................... 6-15 for 220V

Switch Type.................................................................................................. Paddle Safety Switch w/Removable Key

-6-

Motors:

Main

Horsepower................................................................................................................................................ 1 HP

Phase............................................................................................................................................ Single-Phase

Amps....................................................................................................................................................... 14A/7A

Speed................................................................................................................................................ 3450 RPM

Type................................................................................................................. TEFC Capacitor-Start Induction

Power Transfer .................................................................................................................................. Belt Drive

Bearings........................................................................................................ Sealed & Permanently Lubricated

Centrifugal Switch/Contacts Type......................................................................................................... External

Model G0814/G0814X (Mfd. Since 12/22)

Main Specifications:

Main Specifications

Fence Information

Cutterhead Information

Knife Information

Jointer Size.................................................................................................................................................. 6 in.

Bevel Jointing............................................................................................................................. 0 – 45 deg. L/R

Maximum Width of Cut................................................................................................................................ 6 in.

Maximum Depth of Cut............................................................................................................................. 1/8 in.

Minimum Workpiece Length........................................................................................................................ 8 in.

Minimum Workpiece Width....................................................................................................................... 3/4 in.

Minimum Workpiece Thickness................................................................................................................ 1/2 in.

Maximum Rabbeting Depth...................................................................................................................... 1/2 in.

Number of Cuts Per Minute..................................................................................................................... 15,000

Fence Length....................................................................................................................................... 29-1/8 in.

Fence Width.......................................................................................................................................... 1-1/4 in.

Fence Height............................................................................................................................................... 4 in.

Fence Stops............................................................................................................................. 45, 90, 135 deg.

Cutterhead Type........................................................................................................................... Straight Knife

Cutterhead Diameter............................................................................................................................. 2-1/2 in.

Cutterhead Speed............................................................................................................................. 5000 RPM

Number of Knives............................................................................................................................................. 3

Knife Length................................................................................................................................................. 6 in.

Knife Width.................................................................................................................................................. 1 in.

Knife Thickness........................................................................................................................................ 1/8 in.

Knife Adjustment............................................................................................................................ Jack Screws

Table Information

Table Length........................................................................................................................................ 47-3/8 in.

Table Width........................................................................................................................................... 6-5/8 in.

Table Thickness.................................................................................................................................... 1-1/4 in.

Floor to Table Height........................................................................................................................... 33-5/8 in.

Table Adjustment Type........................................................................................................... Handwheel/Lever

Table Movement Type............................................................................................................. Dovetailed Ways

Construction

Base........................................................................................................................................................... Steel

Body Assembly.................................................................................................................................... Cast Iron

Cabinet....................................................................................................................................................... Steel

Fence Assembly.................................................................................................................................. Cast Iron

Guard.......................................................................................................................................... Die Cast Metal

Table....................................................................................................................... Precision-Ground Cast Iron

Paint Type/Finish....................................................................................................................... Powder Coated

Other Information

Number of Dust Ports....................................................................................................................................... 1

Dust Port Size.............................................................................................................................................. 4 in.

Mobile Base............................................................................................................................................. Built-In

Other Specifications:

Country of Origin .............................................................................................................................................. Taiwan

Warranty ........................................................................................................................................................... 1 Year

Approximate Assembly & Setup Time .............................................................................................................. 1 Hour

Serial Number Location .................................................................................................................................. ID Label

ISO 9001 Factory .................................................................................................................................................. Yes

Model G0814/G0814X (Mfd. Since 12/22)

-7-

MACHINE DATA

SHEET

Customer Service #: [phone] · To Order Call: [phone] · Fax #: [phone]

MODEL G0814X 6" JOINTER W/STAND & V‐HELICAL

CUTTERHEAD

Product Dimensions:

Weight.............................................................................................................................................................. 245 lbs.

Width (side-to-side) x Depth (front-to-back) x Height..................................................................... 47-1/2 x 20 x 42 in.

Footprint (Length x Width)..................................................................................................................... 13-1/2 x 18 in.

Shipping Dimensions:

Carton #1

Type........................................................................................................................................... Cardboard Box

Content................................................................................................................................................. Machine

Weight.................................................................................................................................................... 183 lbs.

Length x Width x Height............................................................................................................. 49 x 22 x 13 in.

Must Ship Upright......................................................................................................................................... Yes

Carton #2

Type........................................................................................................................................... Cardboard Box

Content...................................................................................................................................................... Stand

Weight...................................................................................................................................................... 77 lbs.

Length x Width x Height............................................................................................................. 21 x 17 x 30 in.

Must Ship Upright.......................................................................................................................................... No

Electrical:

Power Requirement............................................................................................. 110V or 220V, Single-Phase, 60 Hz

Prewired Voltage.................................................................................................................................................. 110V

Full-Load Current Rating....................................................................................................... 14A at 110V, 7A at 220V

Minimum Circuit Size.......................................................................................................... 20A at 110V, 15A at 220V

Connection Type....................................................................................................................................... Cord & Plug

Power Cord Included.............................................................................................................................................. Yes

Power Cord Length................................................................................................................................................. 6 ft.

Power Cord Gauge......................................................................................................................................... 16 AWG

Plug Included.......................................................................................................................................................... Yes

Included Plug Type................................................................................................................................. 5-15 for 110V

Recommended Plug Type...................................................................................................................... 6-15 for 220V

Switch Type.................................................................................................. Paddle Safety Switch w/Removable Key

-8-

Motors:

Main

Horsepower................................................................................................................................................ 1 HP

Phase............................................................................................................................................ Single-Phase

Amps....................................................................................................................................................... 14A/7A

Speed................................................................................................................................................ 3450 RPM

Type................................................................................................................. TEFC Capacitor-Start Induction

Power Transfer ............................................................................................................................................ Belt

Bearings........................................................................................................ Sealed & Permanently Lubricated

Centrifugal Switch/Contacts Type......................................................................................................... External

Model G0814/G0814X (Mfd. Since 12/22)

Main Specifications:

ISO 9001 Factory .................................................................................................................................................. Yes

Main Specifications

Jointer Size.................................................................................................................................................. 6 in.

Bevel Jointing............................................................................................................................. 0 - 45 deg. L/R

Maximum Width of Cut................................................................................................................................ 6 in.

Maximum Depth of Cut............................................................................................................................. 1/8 in.

Minimum Workpiece Length........................................................................................................................ 8 in.

Minimum Workpiece Width....................................................................................................................... 3/4 in.

Minimum Workpiece Thickness................................................................................................................ 1/2 in.

Maximum Rabbeting Depth...................................................................................................................... 1/2 in.

Number of Cuts Per Minute..................................................................................................................... 20,000

Fence Information

Fence Length....................................................................................................................................... 29-1/8 in.

Fence Width.......................................................................................................................................... 1-1/4 in.

Fence Height............................................................................................................................................... 4 in.

Fence Stops............................................................................................................................. 45, 90, 135 deg.

Cutterhead Information

Cutterhead Type.................................................................................................................................. V-Helical

Cutterhead Diameter............................................................................................................................. 2-1/2 in.

Number of Cutter Rows.................................................................................................................................... 4

Number of Indexable Cutters.......................................................................................................................... 24

Cutterhead Speed............................................................................................................................. 5000 RPM

Cutter Insert Information

Cutter Insert Type.................................................................................................................. Indexable Carbide

Cutter Insert Length.................................................................................................................................. 15mm

Cutter Insert Width.................................................................................................................................... 15mm

Cutter Insert Thickness............................................................................................................................ 2.5mm

Table Information

Table Length........................................................................................................................................ 47-3/8 in.

Table Width........................................................................................................................................... 6-5/8 in.

Table Thickness.................................................................................................................................... 1-1/4 in.

Floor to Table Height........................................................................................................................... 33-5/8 in.

Table Adjustment Type........................................................................................................... Handwheel/Lever

Table Movement Type............................................................................................................. Dovetailed Ways

Construction

Base........................................................................................................................................................... Steel

Body Assembly.................................................................................................................................... Cast Iron

Cabinet....................................................................................................................................................... Steel

Fence Assembly.................................................................................................................................. Cast Iron

Guard.......................................................................................................................................... Die-Cast Metal

Table....................................................................................................................... Precision-Ground Cast Iron

Paint Type/Finish....................................................................................................................... Powder Coated

Other Information

Number of Dust Ports....................................................................................................................................... 1

Dust Port Size.............................................................................................................................................. 4 in.

Mobile Base............................................................................................................................................. Built-In

Other Specifications:

Country of Origin .............................................................................................................................................. Taiwan

Warranty ........................................................................................................................................................... 1 Year

Approximate Assembly & Setup Time .............................................................................................................. 1 Hour

Serial Number Location .................................................................................................................................. ID Label

Model G0814/G0814X (Mfd. Since 12/22)

-9-

SECTION 1: SAFETY

For Your Own Safety, Read Instruction

Manual Before Operating This Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions.
This manual uses a series of symbols and signal words intended to convey the level of impor­tance of the safety messages. The progression of symbols is described below. Remember that
safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures. Always use common sense and good judgment.

Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.

Alerts the user to useful information about proper operation of the

NOTICE

machine to avoid machine damage.

Safety Instructions for Machinery

OWNER’S MANUAL. Read and understand this

owner’smanualBEFOREusingmachine.

TRAINED OPERATORS ONLY. Untrained oper­ators have a higher risk of being hurt or killed.
Only allow trained/supervised people to use this
machine. When machine is not being used, dis­connect power, remove switch keys, or lock-out
machine to prevent unauthorized use—especially
around children. Make your workshop kid proof!

DANGEROUS ENVIRONMENTS. Do not use
machinery in areas that are wet, cluttered, or have
poor lighting. Operating machinery in these areas
greatly increases the risk of accidents and injury.

MENTAL ALERTNESS REQUIRED. Full mental
alertness is required for safe operation of machin­ery. Never operate under the influence of drugs or
alcohol, when tired, or when distracted.

ELECTRICAL EQUIPMENT INJURY RISKS.
You can be shocked, burned, or killed by touching
live electrical components or improperly grounded
machinery. To reduce this risk, only allow qualified
service personnel to do electrical installation or
repair work, and always disconnect power before
accessing or exposing electrical equipment.

DISCONNECT POWER FIRST.
nect machine from power supply BEFORE mak­ing adjustments, changing tooling, or servicing
machine. This prevents an injury risk from unin­tended startup or contact with live electrical com­ponents.

EYE PROTECTION. Always wear ANSI-approved
safety glasses or a face shield when operating
or observing machinery to reduce the risk of eye
injury or blindness from flying particles. Everyday
eyeglasses are NOT approved safety glasses.

Always discon-

-10-

Model G0814/G0814X (Mfd. Since 12/22)

may damage the wires inside. Do not handle

WEARING PROPER APPAREL. Do not wear
loose clothing, gloves, neckties, or jewelry that
can become entangled in moving parts. Always tie
back or cover long hair. Wear non-slip footwear to
reduce risk of slipping and losing control or acci­dentally contacting cutting tool or moving parts.

HAZARDOUS DUST. Dust created by machinery
operations may cause cancer, birth defects, or
long-term respiratory damage. Be aware of dust
hazards associated with each workpiece mate­rial. Always wear a NIOSH-approved respirator to
reduce your risk.

HEARING PROTECTION. Always wear hear­ing protection when operating or observing loud
machinery. Extended exposure to this noise with­out hearing protection can cause permanent
hearing loss.

REMOVE ADJUSTING TOOLS. Tools left on
machinery can become dangerous projectiles
upon startup. Never leave chuck keys, wrenches,
or any other tools on machine. Always verify
removal before starting!

USE CORRECT TOOL FOR THE JOB. Only use
this tool for its intended purpose—do not force
it or an attachment to do a job for which it was
not designed. Never make unapproved modifica­tions—modifying tool or using it differently than
intended may result in malfunction or mechanical
failure that can lead to personal injury or death!

AWKWARD POSITIONS. Keep proper footing
and balance at all times when operating machine.
Do not overreach! Avoid awkward hand positions
that make workpiece control difficult or increase
the risk of accidental injury.

CHILDREN & BYSTANDERS. Keep children and
bystanders at a safe distance from the work area.
Stop using machine if they become a distraction.

GUARDS & COVERS. Guards and covers reduce
accidental contact with moving parts or flying
debris. Make sure they are properly installed,
undamaged, and working correctly BEFORE
operating machine.

FORCING MACHINERY. Do not force machine.
It will do the job safer and better at the rate for
which it was designed.

NEVER STAND ON MACHINE. Serious injury
may occur if machine is tipped or if the cutting
tool is unintentionally contacted.

STABLE MACHINE. Unexpected movement dur­ing operation greatly increases risk of injury or
loss of control. Before starting, verify machine is
stable and mobile base (if used) is locked.

USE RECOMMENDED ACCESSORIES. Consult

thisowner’smanualorthemanufacturerforrec-

ommended accessories. Using improper acces­sories will increase the risk of serious injury.

UNATTENDED OPERATION. To reduce the
risk of accidental injury, turn machine OFF and
ensure all moving parts completely stop before
walking away. Never leave machine running
while unattended.

MAINTAIN WITH CARE. Follow all maintenance
instructions and lubrication schedules to keep
machine in good working condition. A machine
that is improperly maintained could malfunction,
leading to serious personal injury or death.

DAMAGED PARTS. Regularly inspect machine
for damaged, loose, or mis-adjusted parts—or
any condition that could affect safe operation.
Immediately repair/replace BEFORE operating
machine. For your own safety, DO NOT operate
machine with damaged parts!

MAINTAIN POWER CORDS. When disconnect­ing cord-connected machines from power, grab
and pull the plug—NOT the cord. Pulling the cord

cord/plug with wet hands. Avoid cord damage by
keeping it away from heated surfaces, high traffic
areas, harsh chemicals, and wet/damp locations.

EXPERIENCING DIFFICULTIES. If at any time
you experience difficulties performing the intend­ed operation, stop using the machine! Contact our
Technical Support at [phone].

Model G0814/G0814X (Mfd. Since 12/22)

-11-

Additional Safety for Jointers

Kickback or

cutterhead to reach full speed before feeding.

Loose knives or

Serious cuts, amputation, entanglement, or death can occur from contact with rotating cutter­head or other moving components! Flying chips from cutting operations can cause eye injuries
or blindness. Workpieces or inserts/knives thrown by cutterhead (kickback) can strike nearby
operator or bystanders with deadly force. To reduce the risk of serious personal injury from these
hazards, operator and bystanders MUST completely heed the hazards and warnings below.

KICKBACK. Occurs when workpiece is ejected

from machine at a high rate of speed. Kickback
injuries occur from getting struck by workpiece or
hands being pulled into cutterhead. To reduce the
risk of kickback, only use proper workpieces, safe
feeding techniques, and proper machine setup or
maintenance.

GUARD REMOVAL. Operating jointer without
guards unnecessarily exposes operator to knives/
inserts and other hazardous moving parts. Except
when rabbeting, never operate jointer or allow it to
be connected to power if any guards are removed.
Turn jointer OFF and disconnect power before
clearing any shavings or sawdust from around cut­terhead. After rabbeting or maintenance is com­plete, immediately replace all guards and ensure
they are properly installed/adjusted before resum­ing regular operations.

DULL OR DAMAGED KNIVES/INSERTS. Dull or
damaged knives/inserts increase risk of kickback
and cause poor workpiece finish. Only use sharp,
undamaged knives/inserts.

OUTFEED TABLE ALIGNMENT. Setting outfeed
table too high can cause workpiece to hit table or
get stuck while feeding. Setting outfeed table too
low may cause workpiece to rock or shift while
feeding. Both of these results will increase risk
of kickback. Always keep outfeed table even with
knives/inserts at highest point during rotation.

INSPECTING STOCK. Impact injuries or kick­back may result from using improper workpieces.
Thoroughly inspect and prepare workpiece before
cutting. Verify workpiece is free of nails, staples,
loose knots or other foreign material. Always joint
warped workpieces with cupped side facing down.

MAXIMUM CUTTING DEPTH. To reduce risk of
kickback, never cut deeper than

1

⁄8" per pass.

GRAIN DIRECTION. Jointing against the grain
or end grain can increase risk of kickback. It also
requires more cutting force, which produces chat­ter or excessive chip out. Always joint or surface
plane WITH the grain.

CUTTING LIMITATIONS. Cutting workpieces that
do not meet minimum dimension requirements can
result in kickback or accidental contact with cutter­head. Never perform jointing, planing, or rabbeting
cuts on pieces smaller than specified in machine
data sheet.

PUSH BLOCKS. Push blocks reduce risk of acci­dental cutterhead contact with hands. Always use
push blocks when planing materials less than 3"
high or wide. Never pass your hands directly over
cutterhead without a push block.

WORKPIECE SUPPORT. Poor workpiece sup­port or loss of workpiece control while feeding will
increase risk of kickback or accidental contact
with cutterhead. Support workpiece with fence
continuously during operation. Support long stock
with auxiliary tables if necessary.

FEED WORKPIECE PROPERLY.

accidental cutterhead contact may result if work­piece is fed into cutterhead the wrong way. Allow

Never start jointer with workpiece touching cutter­head. Always feed workpiece from infeed side to
outfeed side without stopping until cut is complete.
Never move workpiece backwards while feeding.

SECURE KNIVES/INSERTS.
improperly set inserts can be thrown from cutter­head with dangerous force. Always verify knives/
inserts are secure and properly adjusted before
operation. Straight knives should never project
more than

1

⁄8" (0.125") from cutterhead body.

-12-

Model G0814/G0814X (Mfd. Since 12/22)

SECTION 2: POWER SUPPLY

Before installing the machine, consider the avail­ability and proximity of the required power supply
circuit. If an existing circuit does not meet the
requirements for this machine, a new circuit must
be installed. To minimize the risk of electrocution,
fire, or equipment damage, installation work and
electrical wiring must be done by an electrician or
qualified service personnel in accordance with all
applicable codes and standards.

or equipment damage
may occur if machine is
not properly grounded
and connected to power

The full-load current rating is the amperage a
machine draws at 100% of the rated output power.
On machines with multiple motors, this is the
amperage drawn by the largest motor or sum of all
motors and electrical devices that might operate
at one time during normal operations.

The full-load current is not the maximum amount
of amps that the machine will draw. If the machine
is overloaded, it will draw additional amps beyond
the full-load rating.

If the machine is overloaded for a sufficient length
of time, damage, overheating, or fire may result—
especially if connected to an undersized circuit.
To reduce the risk of these hazards, avoid over­loading the machine during operation and make
sure it is connected to a power supply circuit that
meets the specified circuit requirements.

For your own safety and protection of

Note: Circuit requirements in this manual apply to

a dedicated circuit—where only one machine will
be running on the circuit at a time. If machine will
be connected to a shared circuit where multiple
machines may be running at the same time, con­sult an electrician or qualified service personnel to
ensure circuit is properly sized for safe operation.

A power supply circuit includes all electrical
equipment between the breaker box or fuse panel
in the building and the machine. The power sup­ply circuit used for this machine must be sized to
safely handle the full-load current drawn from the
machine for an extended period of time. (If this
machine is connected to a circuit protected by
fuses, use a time delay fuse marked D.)

This machine can be converted to operate on a
power supply circuit that has a verified ground
and meets the requirements listed below. (Refer
to Voltage Conversion instructions for details.)

This machine is prewired to operate on a power
supply circuit that has a verified ground and meets
the following requirements:

Availability

Electrocution, fire, shock,

supply.

Full-Load Current Rating

Circuit Information

property, consult an electrician if you are
unsure about wiring practices or electrical
codes in your area.

Full-Load Current Rating at 110V ..... 14 Amps

Full-Load Current Rating at 220V

Model G0814/G0814X (Mfd. Since 12/22)

....... 7 Amps

Circuit Requirements for 110V

Nominal Voltage .................... 110V, 115V, 120V

..........................................................60 Hz

Cycle
Phase
Power Supply Circuit
Plug/Receptacle

........................................... Single-Phase

......................... 20 Amps

............................. NEMA 5-15

Circuit Requirements for 220V

Nominal Voltage .........208V, 220V, 230V, 240V

..........................................................60 Hz

Cycle
Phase
Power Supply Circuit
Plug/Receptacle

........................................... Single-Phase

......................... 15 Amps

............................. NEMA 6-15

-13-

Improper connection of the equipment-grounding
wire can result in a risk of electric shock. The
wire with green insulation (with or without yellow
stripes) is the equipment-grounding wire. If repair
or replacement of the power cord or plug is nec­essary, do not connect the equipment-grounding
wire to a live (current carrying) terminal.

Check with a qualified electrician or service per­sonnel if you do not understand these grounding
requirements, or if you are in doubt about whether
the tool is properly grounded. If you ever notice
that a cord or plug is damaged or worn, discon­nect it from power, and immediately replace it with

We do not recommend using an extension cord
with this machine. If you must use an extension
cord, only use it if absolutely necessary and only
on a temporary basis.

Extension cords cause voltage drop, which can
damage electrical components and shorten motor
life. Voltage drop increases as the extension cord
size gets longer and the gauge size gets smaller
(higher gauge numbers indicate smaller sizes).

Any extension cord used with this machine must
be in good condition and contain a ground wire
and matching plug/receptacle. Additionally, it must
meet the following size requirements:

Grounding Requirements

This machine MUST be grounded. In the event
of certain malfunctions or breakdowns, grounding
reduces the risk of electric shock by providing a
path of least resistance for electric current.

For 110V operation: This machine is equipped
with a power cord that has an equipment-ground­ing wire and a grounding plug (see following fig­ure). The plug must only be inserted into a match­ing receptacle (outlet) that is properly installed
and grounded in accordance with all local codes
and ordinances.

For 220V operation: The plug specified under
“

on the previ­ous page has a grounding prong that must be
attached to the equipment-grounding wire on
the included power cord. The plug must only be
inserted into a matching receptacle (see following
figure) that is properly installed and grounded in
accordance with all local codes and ordinances.

Two-prong outlets do not meet the
grounding requirements for this machine.

provided—if it will not fit the outlet, have a

GROUNDED

5-15 RECEPTACLE

Grounding Pin

5-15 PLUG

GROUNDED

6-15 RECEPTACLE

Current Carrying Prongs

6-15 PLUG

Grounding Pin

Figure 6. Typical 6-15 plug and receptacle.

Neutral Hot

Figure 5. Typical 5-15 plug and receptacle.

SHOCK HAZARD!

Do not modify or use an adapter on the plug

qualified electrician install the proper outlet
with a verified ground.

Circuit Requirements for 220V”

-14-

Extension Cords

Minimum Gauge Size ........................... 14 AWG

Maximum Length (Shorter is Better)

Model G0814/G0814X (Mfd. Since 12/22)

.......50 ft.

Voltage Conversion

to 220V

4. Use wire nuts to connect wires as indicated

in Figure 8. Twist wire nuts onto their respec­tive wires and wrap them with electrical tape
so they will not come loose.

The voltage conversion MUST be performed by
an electrician or qualified service personnel.

The voltage conversion procedure consists of
rewiring the motor and installing the correct plug.
A wiring diagram is provided on Page 57 for your
reference.

IMPORTANT: If the diagram included on the
motor conflicts with the one on Page 57, the motor
may have changed since the manual was printed.
Use the diagram provided on the motor junction
box instead.

Item(s) Needed Qty

Phillips Head Screwdriver #2 ............................ 1

Electrical Tape
Wire Nut (16 AWG x 3)
6-15 Plug
Wire Cutters/Stripper

To convert voltage to 220V:

................................... As Needed

...................................... 1

........................................................... 1

......................................... 1

Connect Wires

and Secure

with Nuts

Figure 8. Motor rewired to 220V.

Close and secure motor junction box.

5.

6. Install a 6-15 plug according to manufac-

turer's instructions. If plug manufacturer's
instructions are not available, NEMA stan­dard 6-15 plug wiring is provided on Page 57.

To Switch

Ground

1. DISCONNECT MACHINE FROM POWER!

2. Cut off existing 5-15 plug.

3. Open motor junction box, remove (2) wire

nuts indicated in Figure 7, then disconnect
wires.

Remove

Wire

Nuts and

Disconnect

Wires

Figure 7. Inside motor junction box (motor pre-

To Switch

Ground

wired to 110V).

Model G0814/G0814X (Mfd. Since 12/22)

-15-

SECTION 3: SETUP

The following items are needed, but not included,
for the setup/assembly of this machine.

This machine was carefully packaged for safe
transport. When unpacking, separate all enclosed
items from packaging materials and inspect them
for shipping damage.

,

please

IMPORTANT: Save all packaging materials until
you are completely satisfied with the machine and
have resolved any issues between Grizzly or the
shipping agent. You MUST have the original pack-

aging to file a freight claim. It is also extremely
helpful if you need to return your machine later.

Needed for Setup

This machine presents
serious injury hazards
to untrained users. Read
through this entire manual
to become familiar with
the controls and opera­tions before starting the
machine!

Wear safety glasses during
the entire setup process!

HEAV Y LIFT!
Straining or crushing injury
may occur from improperly
lifting machine or some of
its parts. To reduce this risk,
get help from other people
and use a forklift (or other
lifting equipment) rated for
weight of this machine.

Description Qty

• Safety Glasses (for each person) ............... 1

• Another Person .......................................... 1

• Solvent/Cleaner .......................... As Needed

• Disposable Rags/Gloves ............ As Needed

• Wrench or Socket 9⁄16 " ................................ 1

• Hex Wrench 5mm ....................................... 1

• Hex Wrench 1⁄8" (G0814X Only) ................. 1

• Straightedge 4' ........................................... 1

• Stubby Phillips Head Screwdriver #2 ......... 1

• Dust Collection System .............................. 1

• 4" Dust Hose (length as needed) ............... 1

• 4" Hose Clamps ......................................... 2

• Scrap Wood ................................ As Needed

call us immediately at [phone].

Unpacking

If items are damaged

Like all machinery there is potential danger
when operating this machine. Accidents
are frequently caused by lack of familiarity
or failure to pay attention. Use this machine
with respect and caution to decrease the
risk of operator injury. If normal safety pre­cautions are overlooked or ignored, seri­ous personal injury may occur.

-16-

No list of safety guidelines can be com­plete. Every shop environment is different.
Always consider safety first, as it applies
to your individual working conditions. Use
this and other machinery with caution and
respect. Failure to do so could result in
serious personal injury, damage to equip­ment, or poor work results.

Model G0814/G0814X (Mfd. Since 12/22)

Inventory

The following is a list of items shipped with your
machine. Before beginning setup, lay these items
out and inventory them.

If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.

A

Box #1 Inventory (Figure 9) Qty

A. Jointer Assembly w/Carriage Mount........... 1

Fence Assembly & Carriage ...................... 1

B.

Cutterhead Guard Assembly ...................... 1

C.

D. Belt Guard .................................................. 1

. Knife-Setting Jig (G0814) ........................... 1

E

Push Blocks ................................................ 2

F.

Hex Wrench 3mm (G0814) ......................... 1

G.

Belt ............................................................. 1

H.

Fence Lock w/Locking Nut & Washer ........ 1

I.

Fence Tilt Lever .......................................... 1

J.

Open-End Wrenches 8/10, 12/14mm ...1 Ea.

K.

T-Handle Torx Wrench 1⁄4" (G 0 814X) ........... 1

L.

T20 Torx Bits (G0814X) ............................... 5

M.

Flat HD Torx Screws M6-1 x 15 (G0814X) ... 10

N.

Indexable Inserts 15 x 15 x 2.5 (G0814X) ... 5

O.

Outfeed Table Handwheel .......................... 1

P.

Carriage Support Key 3⁄8" x 3⁄8" x 9" ........... 1

Q.

Dust Port 4" ................................................ 1

R.

Foot Pedal Caster Assembly ...................... 1

S.

B

F

E

I

H

M

L

P

R

Figure 9. Box #1 inventory.

C

J

N

S

D

G

K

O

Q

Box #2 Inventory (Not Shown) Qty

• Stand Assembly w/Motor ........................... 1

Fasteners (Page 18)

• Hex Bolts 3⁄8"-16 x 21⁄2 " (Wheel/Stand) ....... 2

• Flat Washers 3⁄8" (Wheel/Stand) ................ 4

• Hex Nuts 3⁄8"-16 ( Wheel/Stand) .................. 2

• Hex Bolt 5⁄16 "-18 x 2" (Wheel/Stand) ........... 1

• Flat Washer 5⁄16 " (Wheel/Stand) ................. 1

• Hex Bolts 3⁄8"-16 x 3⁄4" (Jointer/Stand) ......... 3

• Flat Washers 3⁄8" (Jointer/Stand) ................ 3

• Hex Bolt 5⁄16 "-18 x 21⁄2 " (Belt Guard) ........... 1

• Flat Washer 5⁄16 " (Belt Guard) ..................... 1

Model G0814/G0814X (Mfd. Since 12/22)

NOTICE

If you cannot find an item on this list, care­fully check around/inside the machine and
packaging materials. Often, these items get
lost in packaging materials while unpack­ing or they are pre-installed at the factory.

-17-

Hardware Recognition Chart

USE THIS CHART TO MATCH UP
HARDWARE DURING THE INVENTORY
AND ASSEMBLY PROCESS.

Flat
Head
Cap
Screw

-18-

5mm

5mm

Model G0814/G0814X (Mfd. Since 12/22)

parts of the

The unpainted surfaces of your machine are
coated with a heavy-duty rust preventative that
prevents corrosion during shipment and storage.
This rust preventative works extremely well, but it
will take a little time to clean.

Be patient and do a thorough job cleaning your
machine. The time you spend doing this now will
give you a better appreciation for the proper care
of your machine's unpainted surfaces.

There are many ways to remove this rust preven­tative, but the following steps work well in a wide
variety of situations. Always follow the manufac-

turer’sinstructionswithanycleaningproductyou

use and make sure you work in a well-ventilated
area to minimize exposure to toxic fumes.

Before cleaning, gather the following:

• Disposable rags

• Cleaner/degreaser (WD•40 works well)

• Safety glasses & disposable gloves

• Plastic paint scraper (optional)

Basic steps for removing rust preventative:

1.

2.

3.

4.

Many cleaning solvents

work in a well-ventilated

Cleanup

Gasoline and petroleum
products have low flash
points and can explode
or cause fire if used to
clean machinery. A v o id
using these products
to clean machinery.

Put on safety glasses.

Coat the rust preventative with a liberal

amount of cleaner/degreaser, then let it soak
for 5–10 minutes.

Wipe off the surfaces. If your cleaner/degreas-

er is effective, the rust preventative will wipe
off easily. If you have a plastic paint scraper,
scrape off as much as you can first, then wipe
off the rest with the rag.

are toxic if inhaled. Only

area.

NOTICE

Avoid harsh solvents like acetone or brake
parts cleaner that may damage painted sur­faces. Always test on a small, inconspicu­ous location first.

T23692—Orange Power Degreaser

A great product for removing the waxy ship­ping grease from the non-painted
machine during clean up.

Order online at

www.grizzly.com

OR

Call 1-800-523-4777

Repeat Steps 2–3 as necessary until clean,

then coat all unpainted surfaces with a quality
metal protectant to prevent rust.

Model G0814/G0814X (Mfd. Since 12/22)

Figure 10. T23692 Orange Power Degreaser.

-19-

Site Considerations

Weight Load

Refer to the
of your machine. Make sure that the surface upon
which the machine is placed will bear the weight
of the machine, additional equipment that may be
installed on the machine, and the heaviest work­piece that will be used. Additionally, consider the
weight of the operator and any dynamic loading
that may occur when operating the machine.

Space Allocation

Consider the largest size of workpiece that will
be processed through this machine and provide
enough space around the machine for adequate
operator material handling or the installation of
auxiliary equipment. With permanent installations,
leave enough space around the machine to open
or remove doors/covers as required by the main­tenance and service described in this manual.

See below for required space allocation.

Physical Environment

The physical environment where the machine is
operated is important for safe operation and lon­gevity of machine components. For best results,
operate this machine in a dry environment that is
free from excessive moisture, hazardous chemi­cals, airborne abrasives, or extreme conditions.
Extreme conditions for this type of machinery are
generally those where the ambient temperature
range exceeds 41°–104°F; the relative humidity
range exceeds 20%–95% (non-condensing); or
the environment is subject to vibration, shocks,

Place this machine near an existing power source.
Make sure all power cords are protected from
traffic, material handling, moisture, chemicals, or
other hazards. Make sure to leave enough space
around machine to disconnect power supply or

Lighting around the machine must be adequate
enough that operations can be performed safely.
Shadows, glare, or strobe effects that may distract
or impede the operator must be eliminated.

Machine Data Sheet for the weight

or bumps.

Electrical Installation

Children or untrained people
may be seriously injured by
this machine. Only install in an
access restricted location.

471/2"

apply a lockout/tagout device, if required.

Lighting

Wall

Min. 30"

for Maintenance

20"

-20-

= Electrical Connection

Figure 11. Minimum working clearances.

Model G0814/G0814X (Mfd. Since 12/22)

Assembly

The machine must be fully assembled before it
can be operated. Before beginning the assembly
process, refer to

and gather

all

To ensure the assembly process
goes smoothly, first clean any
ered or coated in heavy-duty rust preventative (if
applicable).

5. With help of another person, place jointer

assembly onto stand. Attach assembly to

3

stand with (3)

⁄8"-16 x 3⁄4" hex bolts and 3⁄8"

flat washers (see Figure 13).

Needed for Setup

listed items.

parts that are cov-

To assemble machine:

Turn stand upside down and place top on flat

1.

surface.

Attach foot pedal caster assembly to side of

2.

mobile base chassis with leveling feet, using

3

⁄8"-16 x 21⁄2" hex bolts, (4) 3⁄8" flat wash-

(2)
ers, (2)
hex bolt and (1)

3

⁄8"-16 hex nuts, and (1) 5⁄16"-18 x 2"

5

⁄16" flat washer, as shown in

Figure 12.

x 2

Note: Reach through dust chute to install fas-

teners on left side of stand. Ensure cutterhead
pulley is positioned above slot in stand.

Slot

x 3

Figure 13. Example of jointer assembly attached

to stand.

Place straightedge against pulleys to check

6.

their alignment (see Figures 14–15).

— If pulleys are aligned, go to Step 8.

— If pulleys are not aligned, go to Step 7.

(Interior View)

Figure 12. Pedal assembly attached to right side

of stand.

3. Place stand in upright position and adjust lev-

eling feet as needed with hex nuts so stand
rests level and stable on floor.

Remove rear panel to access mounting holes

4.

in stand during next step.

Model G0814/G0814X (Mfd. Since 12/22)

Straightedge

Figure 14. Example of checking belt alignment.

Cutterhead

Pulley

Alignment

Motor

Pulley

Figure 15. Pulley alignment.

-21-

7.

Loosen set screws on cutterhead or motor

pulley as needed to align pulleys, then tighten
set screws (see Figure 16).

x 2

Pulley

Figure 16. Motor pulley set screw locations.

9.

Slide motor upward, place belt around

cutterhead and motor pulleys, then slide
motor down to rest on belt (see Figure 18).

Belt

8. Loosen motor mount hex nuts shown in
Figure 17, but DO NOT completely remove

them.

x 4

Figure 17. Location of motor mount hex nuts.

Figure 18. Example of belt installed onto

cutterhead and motor pulleys.

10. Adjust belt tension by applying downward

pressure on motor until there is approxi-

1

mately

⁄4" deflection when belt is pushed with

moderate force, as shown in Figure 19.

Note: After the first 16 hours of operation,

check and re-tension the belt, as it may
stretch and seat during this time, which will
cause it to lose the initial tension you set.

Cutterhead Pulley

Approximately

1

/4" Deflection

Motor Pulley

-22-

Figure 19. Correct belt deflection when properly

tensioned.

11.

Tighten motor mount bolts/nuts (see

Figure 17) and replace rear panel.

Model G0814/G0814X (Mfd. Since 12/22)

12.

Remove 1⁄4"-20 x 1⁄2" Phillips head screw and

1

⁄4" flat washer from end of cutterhead guard

shaft, loosen set screw in rabbeting table,
then slide shaft down through cutterhead
guard mounting hole (see Figure 20).

— If guard does fully seat in hole, proceed to

Step 13.

— If guard does not fully seat in hole, rotate

guard until it is fully seated, then proceed
to Step 13.

Cutterhead Guard

Assembly

Cutterhead Guard

Mounting Hole

Infeed Table

Rotate cutterhead guard counterclockwise

14.

and secure temporarily with a piece of scrap
wood (see Figure 22).

Scrap
Wood

Figure 22. Example of cutterhead guard secured

in place.

15. Place carriage support key and fence onto

fence carriage base, making sure fence
fits over key, and insert fence lock with flat
washer on top through carriage, then secure
with fence locking nut (see Figure 23).

Figure 20. Installing cutterhead guard.

Align corner of cutterhead guard with edge

13.

of carriage, then secure set screw,

1

⁄2" Phillips head screw, and 1⁄4" flat washer

1

⁄4"-20 x

removed in Step 12 (see Figure 21).

Alignment Area

Carriage

Cutterhead

Guard

Figure 21. Cutterhead guard aligned with

carriage.

Top View

Fence

Flat

Lock

Washer

Carriage

Support

Key

Fence

Carriage

Base

Bottom View

Fence

Locking

Nut

Figure 23. Fence assembly installed onto

carriage base and secured with fence lock.

Model G0814/G0814X (Mfd. Since 12/22)

-23-

Note: There is a small, plastic pin in under-

side of fence (see Figure 24). This pin should
slide along table or carriage base to prevent
fence from scraping table.

Fence Support

Pin

Figure 24. Location of plastic fence support pin.

16. Install fence tilt lever (see Figure 25).

Outfeed table MUST be level with cutterhead
knives/inserts when they are at top dead
center (at their highest point during rota­tion). Otherwise, workpiece cannot properly
feed past cutterhead, which may cause a
kickback hazard for the operator.

18. Verify outfeed table height is set correctly

with knives/inserts at top dead center (TDC)
(refer to Setting Outfeed Table Height on
Page 46) and all knives/inserts are securely
tightened in cutterhead.

Cutterhead guard must always return to
closed position whenever it is moved. If it
does not do this, it must be re-adjusted or
re-installed.

Tilt Lever

Figure 25. Fence tilt lever installed.

17. Install outfeed table handwheel, as shown

3

in Figure 26, using 10-24 x

⁄8" pre-installed

Phillips head screw and #10 flat washer.

Outfeed

Table

Handwheel

Remove scrap wood installed in Step 14 and

19.

test operation of guard by pulling it back.
Guard should spring back over cutterhead
and stop against fence.

If guard does not snap back, or snaps back

—

slowly, proceed to Checking/Adjusting
Cutterhead Guard on Page 53 before
continuing to Step 20.

Figure 26. Outfeed table handwheel installed.

-24-

Model G0814/G0814X (Mfd. Since 12/22)

20. Install belt guard with 5⁄16"-18 x 21⁄2" hex bolt

21.

Figure 27. Belt guard and dust port installed.

22. G0814 Only: Assemble knife-setting gauge,

5

⁄16" flat washer (see Figure 27).

and

Install dust port, as shown in Figure 27, using

(4) pre-installed flange screws.

x 4

Dust

Port

as shown in Figure 28.

Dust Collection

This machine creates a lot of wood chips/
dust during operation. Breathing airborne
dust on a regular basis can result in perma­nent respiratory illness. Reduce your risk
by wearing a respirator and capturing the
dust with a dust-collection system.

Recommended CFM at Dust Port: 400 CFM

Do not confuse this CFM recommendation with
the rating of the dust collector. To determine the
CFM at the dust port, you must consider these
variables: (1) CFM rating of the dust collector,
(2) hose type and length between the dust col­lector and the machine, (3) number of branches
or wyes, and (4) amount of other open lines
throughout the system. Explaining how to cal­culate these variables is beyond the scope of
this manual. Consult an expert or purchase a
good dust collection "how-to" book.

Figure 28. Knife-setting gauge assembled.

To connect dust collection hose:

1. Fit 4" dust hose over dust port, as shown in
Figure 29, and secure with a hose clamp.

Figure 29. Dust hose attached to dust port.

2.

Tug hose to make sure it does not come off.

Model G0814/G0814X (Mfd. Since 12/22)

Note: A tight fit is necessary for proper

performance.

-25-

Test Run

Once assembly is complete, test run the machine
to ensure it is properly connected to power and
safety components are functioning correctly.

If you find an unusual problem during the test run,
immediately stop the machine, disconnect it from
power, and fix the problem BEFORE operating the
machine again. The

table in the

SERVICE section of this manual can help.

DO NOT start machine until all preceding
setup instructions have been performed.
Operating an improperly set up machine

ed results that can lead to serious injury,

connecting machine to power before

Troubleshooting

The Test Run consists of verifying the following:

1) The motor powers up and runs correctly, and

2) the switch disabling key disables the switch
properly.

Serious personal injury could occur from

completing the setup process described in
this manual. DO NOT connect power until
instructed to do so later in this manual.

Figure 30. Removing key from paddle switch.

Try to start machine with paddle switch.

5.

Machine should not start.

— If machine does not start, switch dis-

abling feature is working as designed.
Congratulations! Test run is complete.
Proceed to Recommended Adjustments.

— If machine does start, immediately stop

machine. Switch disabling feature is not
working correctly. This safety feature must
work properly before proceeding with
operations. Call Tech Support for help.

Recommended

Adjustments

may result in malfunction or unexpect-

death, or machine/property damage.

To test run the machine:

1. Clear all setup tools away from machine.

2. Connect machine to power supply.

3. Turn machine ON, verify motor operation,

and then turn machine OFF.

The motor should run smoothly and without

unusual problems or noises.

Remove switch disabling key, as shown in

4.
Figure 30.

-26-

For your convenience, the adjustments listed
below have been performed at the factory and no
further setup is required to operate your machine.

However, because of the many variables involved
with shipping, we recommend that you at least
verify the following adjustments to ensure the best
possible results from your new machine.

Step-by-step instructions for these adjustments
can be found in SECTION 7: SERVICE.

Factory adjustments that should be verified:

Knife/Insert Settings (Pages 42 & 44).

1.

2. Depth Scale Calibration (Page 47).

Fence Stop Accuracy (Page 49).

3.

Table Parallelism (Page 52).

4.

Model G0814/G0814X (Mfd. Since 12/22)

SECTION 4: OPERATIONS

The purpose of this overview is to provide the
novice machine operator with a basic understand­ing of how the machine is used during operation,
so the

discussed

later in this manual

Due to the generic nature of this overview, it is
not intended to be an instructional guide. To learn
more about specific operations, read this entire
manual,

training from experienced
machine operators, and do additional research
outside of this manual by reading "how-to" books,
trade magazines, or websites.

To reduce your risk of
serious injury, read this
entire manual BEFORE

To reduce risk of eye injury from flying

Operation Overview

machine controls/components

are easier to understand.

seek additional

using machine.

To complete a typical operation, the operator
does the following:

Examines workpiece to verify it is safe and

1.

suitable for jointing.

Adjusts fence for width of workpiece and

2.

locks it in place.

Adjusts fence tilt, if necessary.

3.

Adjusts infeed table height to set depth of cut

4.

per pass.

Ensures cutterhead guard position and oper-

5.

ation are functioning properly.

Puts on safety glasses, respirator, and any

6.

other required protective equipment.

Starts dust collection and jointer.

7.

Using push blocks as needed, holds

8.

workpiece firmly against infeed table and
fence, and feeds workpiece into cutterhead at
a steady and controlled rate until entire length
of workpiece has been cut and it clears the
cutterhead on the outfeed table side.

chips or lung damage from breathing dust,
always wear safety glasses and a respirator
when operating this machine.

If you are not experienced with this type
of machine, WE STRONGLY RECOMMEND
that you seek additional training outside of
this manual. Read books/magazines or get
formal training before beginning any proj­ects. Regardless of the content in this sec­tion, Grizzly Industrial will not be held liable
for accidents caused by lack of training.

Model G0814/G0814X (Mfd. Since 12/22)

Repeats cutting process described above

9.

until desired results are achieved.

Stops jointer and dust collection.

10.

-27-

Stock Inspection &

Follow these rules when choosing and jointing
stock:

• DO NOT joint or surface plane stock that

Injury to the
operator or damage to the workpiece can
occur if a knot becomes dislodged during the

• DO NOT joint or surface plane against the

Cutting against the grain

increases the likelihood of kickback, as well

• Jointing and surface planing with the

grain produces a better finish and is safer

Cutting with the grain is
described as feeding the stock on the jointer so
the grain points down and toward you as viewed

If the grain changes direction along the
edge of the board, decrease the cutting depth
and make additional passes.

• Scrape all glue off the workpiece before

Glue deposits on the workpiece,

hard or soft, will gum up the cutterhead and

• Remove foreign objects from the work-

Make sure that any stock you pro­cess with the jointer is clean and free of dirt,
nails, staples, tiny rocks or any other foreign
objects that could damage the cutterhead.
These particles could also cause a spark as
they strike the cutterhead and create a fire

Wood stacked on a concrete

or dirt surface can have small pieces of con-

• Make sure all stock is sufficiently dried

Wood with a moisture con­tent over 20% will cause unnecessary wear
on the cutters and poor cutting results. Excess
moisture can also hasten rust and corrosion.

10" Min.

1

/4" Min.

3

/4" Min.

Edge Jointing

• Only cut natural wood. This jointer is only

designed for cutting natural wood stock.

wood, laminates, drywall, backer board, metals,
glass, stone, tile, products with lead-based
paint, or products that contain asbestos. Cutting
these may lead to injury or machine damage.

Make sure your workpiece exceeds the
minimum dimension requirements shown
below before processing it through the

jointing.

Requirements

contains large or loose knots.

cutting operation.

grain direction.

as tear-out on the workpiece.

for the operator.

on the edge of the stock (see Figure below).

produce poor results.

piece.

hazard.

IMPORTANT:

crete or stone pressed into the surface.

before jointing.

Note:

CORRECT

INCORRECT

Figure 31. Proper grain alignment with cutterhead.

Never use it to cut MDF, particle board, ply-

-28-

With Grain

Against Grain

jointer, or the workpiece may break or kick
back during the operation.

Edge Jointing

10" Min.

3

/4" Min.

1

/4" Min.

Surface Planing

10" Min.

1

/2" Min.

3

/4" Min.

Figure 32. Minimum stock dimensions for jointer.

Model G0814/G0814X (Mfd. Since 12/22)

Setting Depth of Cut

The depth of cut on a jointer is the amount of mate­rial removed from the bottom of the workpiece as
it passes over the cutterhead.

The depth of cut is set by adjusting the height of
the infeed table relative to the cutterhead knives/
inserts at TDC (top dead center).

Depth-of-Cut Scale

The depth of cut can be referenced directly from
the depth scale located on the front of the jointer
(see Figures 34–35).

Note: The depth scale can be calibrated or
"zeroed" if it is not correct. Refer to Calibrating
Depth Scale on Page 47 for more information.

DO NOT exceed 1⁄8" depth of cut per pass
when edge jointing and
pass when surface planing on this machine
or kickback and serious injury may occur!

1

⁄16" depth of cut per

Adjusting Infeed Table Height

To adjust the infeed table height, loosen the infeed
table lock, adjust the infeed table lever, then tight­en the lock to secure the setting (see Figure 33).
To set the maximum height (i.e. minimum depth of
cut), thread the stop bolt into the base and tighten
the jam nut shown in Figure 35.

Figure 34. Location of depth-of-cut scale.

Depth

Indicator

Scale

Jam Nut

Stop Bolt

Infeed

Table

Lock

Figure 33. Infeed table controls.

Model G0814/G0814X (Mfd. Since 12/22)

Infeed

Table
Lever

Figure 35. Example of depth-of-cut scale

components.

-29-

Squaring Stock

Jointed Edge

Squaring stock involves four steps performed
in the order below:

1. Surface Plane on Jointer—Concave face of

workpiece is surface planed flat with jointer.

2. Surface Plane on a Thickness Planer—

Opposite face of workpiece is surface planed
flat with a thickness planer.

3. Edge Joint on Jointer—Concave edge of

workpiece is jointed flat with jointer.

4. Rip Cut on a Table Saw—Jointed edge

of workpiece is placed against a table saw
fence and opposite edge cut off.

Opposite Edge

45

30

15

Rip Cut with

Table Saw

Previously

Previously Surface

Planed Face

-30-

Model G0814/G0814X (Mfd. Since 12/22)

To surface plane on jointer:

1.
Stock Inspection &

2. Set infeed table height to desired cutting

To minimize risk of kickback,

" per pass

3.

4.

5. Place workpiece firmly against fence and

To ensure workpiece remains

of workpiece

6.

head while keeping it firmly against fence

Keep hands at least 4" away
from cutterhead during the entire cut. Instead
of allowing a hand to pass directly over cut­terhead, lift it up and over cutterhead, and
safely reposition it on the outfeed side to con­tinue supporting workpiece. Use push blocks
whenever practical to further reduce risk of

7.

When squaring up stock, cut opposite
side of workpiece with a planer instead of the
jointer to ensure both sides are parallel.

Surface Planing

Failure to use push blocks when surface

ing rotating cutterhead, which will cause
serious personal injury. ALWAYS use push

The purpose of surface planing (see example

Figures

on the jointer is to make one flat
face on a piece of stock to prepare it for thickness
planing on a planer.

below)

planing could result in your hands contact-

Inspect stock to ensure it is safe and suitable

for the operation (see
Requirements section).

depth for each pass.

CAUTION:

do not exceed a cutting depth of
when surface planing.

Set fence to 90°.

1

⁄16

blocks when surface planing on jointer!

Start jointer.

infeed table.

CAUTION:

stable during cut, concave sides
must face toward table and fence.

Feed workpiece completely across cutter-

and tables during the entire cut.

CAUTION:

accidental hand contact with cutterhead.

Repeat Step 6 until entire surface is flat.

Removed

Figure 36. Example photo of a surface planing

Model G0814/G0814X (Mfd. Since 12/22)

Surface

operation.

Tip:

-31-

Edge Jointing

To edge joint on jointer:

1.

Stock Inspection &

2.

Surface

3. Set infeed table height to desired cutting

To minimize risk of kickback,

.

4.

5.

6. Place workpiece firmly against fence and

To ensure workpiece remains

of workpiece

7.

head while keeping it firmly against fence

Keep hands at least 4" away
from cutterhead during the entire cut. Instead
of allowing a hand to pass directly over cut­terhead, lift it up and over cutterhead, and
safely reposition it on the outfeed side to con­tinue supporting workpiece. Use push blocks
whenever practical to further reduce risk of

8.

When squaring up stock, cut opposite
edge of workpiece with a table saw instead
of the jointer—otherwise, both edges of work­piece will not be parallel with each other.

Edge jointing (see example Figures below) pro­duces a flat and true surface along the side of
a workpiece by removing uneven areas.

an

essential step for

or rough
stock and when preparing a workpiece for joinery
or finishing.

Inspect stock to ensure it is safe and suitable

for the operation (see
Requirements section).

squaring up warped

It is

Surface plane workpiece (see

Planing section).

depth for each pass.

CAUTION:

do not exceed a cutting depth of

Set fence to 90°.

Start jointer.

infeed table with concave side facing down.

CAUTION:

stable during cut, concave sides
must face toward table and fence.

Feed workpiece completely across cutter-

and tables during the entire cut.

CAUTION:

1

⁄8" per pass

Figure 37. Example photo of an edge jointing

-32-

Removed

Surface

operation.

accidental hand contact with cutterhead.

Repeat Step 6 until the entire edge is flat.

Tip:

Model G0814/G0814X (Mfd. Since 12/22)

Bevel Cutting

To bevel cut on jointer:

1.

Stock Inspection &

2.

Surface

3.

g

4. Set infeed table height to cutting depth

Cutting depth for bevel cuts is

, depending on

5.

6.

7.

8.

workpiece against table and fence with firm
pressure, and feed workpiece over cutter-

When your leading hand gets
within 4" of the cutterhead, lift it up and over
cutterhead, and place push block on portion

.
Now, focus your pressure on outfeed end
of the workpiece while feeding, and repeat
same action with your trailing hand when it

keep

your hands safe, DO NOT let them get closer

at any time

9.

you are satisfied with the results.

Bevel cuts (see example Figures below) can be
made by setting the fence at the desired angle
and feeding the workpiece firmly along the fence
face, with the bottom inside corner firmly against
the table. The cutting process typically requires
multiple passes or cuts to bevel the entire edge
of a workpiece.

Inspect stock to ensure it is safe and suitable

for the operation (see
Requirements section).

Surface plane workpiece (see

Planing section).

Edge joint workpiece (see Edge Jointin

section).

desired for each pass.

CAUTION:

typically between
hardness and width of stock.

Set fence tilt to desired angle of cut.

Place workpiece against fence and infeed

table with concave side face down.

Start jointer.

With a push block in your leading hand, press

head with a push block in your trailing hand.

CAUTION:

of the workpiece once it is 4" past cutterhead

1

⁄16" and 1⁄8"

Removed

Figure 38. Example photo of fence setup for a

bevel cut of 45°.

Model G0814/G0814X (Mfd. Since 12/22)

Surface

gets within 4" of cutterhead. To help

than 4" from moving cutterhead
during operation!

Repeat cutting process, as necessary, until

-33-

Rabbet Cutting

A rabbet cut removes a portion of a workpiece
edge, so it fits together with an opposing, equally
sized rabbet cut on another workpiece (see exam­ple

. This is a classic method of

joining two workpieces that is simple, yet strong.

This jointer can be used to make high-quality rab­bet cuts, but there are some situations—whether
it

s due to an excessively large/small workpiece
size or rabbet cutting width/depth—when it will not
be safe or appropriate for making the rabbet cut
on this jointer. In these cases, you need to use
another tool or method for rabbet cutting that will
be a safer alternative.

A

alternatively be made using a
table saw, router, or even a hand saw. As with any
type of cutting operation, always consider your
safety first and use good

Typically, rabbet cutting with a jointer requires
the cutterhead guard to be removed first, so the
workpiece can slide along the rabbeting ledge
during the cut. However, it is possible to make
rabbet cuts with workpieces up to 1

without
removing the cutterhead guard. This is done by
performing the rabbet cut with the workpiece on
end (similar to when you are edge jointing).

To rabbet cut on jointer:

Inspect stock to ensure it is safe and suitable

1.
for the operation (see Stock Inspection &
Requirements section).

Figure below)

Removed

Surface

i

Rabbet Joints

2. Set infeed table height to desired cutting
depth for each pass.

CAUTION: For safety reasons, cutting

depth should never exceed

Remove cutterhead guard if necessary to per-

3.

form operation (see Figure 39).

Guard Installed

1

⁄8" per pass.

rabbet cut can

-34-

judgement!

" thick

Guard Removed

Figure 39. Examples of typical rabbet cutting

operations.

Model G0814/G0814X (Mfd. Since 12/22)

When cutterhead guard is removed,

essary exposure to cutterhead, always

Feed workpiece completely across cutterhead

7.

while keeping it firmly against fence and
tables during entire cut.

attempting any other cut besides a rabbet
directly exposes operator to moving cutter­head. To minimize risk of injury and unnec-

keep cutterhead guard installed when pos­sible, and ALWAYS immediately replace it
after performing rabbet cuts.

4. Set fence to 90° and near front of jointer,

so amount of exposed cutterhead in front of
fence matches size of desired rabbet.

Start jointer.

5.

6. Place workpiece firmly against fence and

infeed table.

CAUTION: To ensure workpiece remains

stable during cut, concave sides of workpiece
must face toward table and fence.

CAUTION: Keep hands at least 4" away

from cutterhead during the entire cut. Instead
of allowing a hand to pass directly over
cutterhead, lift it up and over cutterhead, and
safely reposition it on the outfeed side to con­tinue supporting workpiece. Use push blocks
whenever practical to further reduce risk of
accidental hand contact with cutterhead.

Repeat Step 7 until rabbet is cut to depth.

8.

Re-install cutterhead guard if removed in

9.
Step 3 as instructed in Checking/Adjusting
Cutterhead Guard on Page 53.

Model G0814/G0814X (Mfd. Since 12/22)

-35-

SECTION 5: ACCESSORIES

Installing unapproved accessories may

order online at www.grizzly.com or call 1-800-523-4777

cause machine to malfunction, resulting in
serious personal injury or machine damage.
To reduce this risk, only install accessories
recommended for this machine by Grizzly.

NOTICE

Refer to our website or latest catalog for
additional recommended accessories.

T23246—The Missing Shop Manual: Jointer

Dedicated to providing integral information about
woodworking tools and techniques that other
manuals overlook, the books in this series contain
safety facts, explanations about basic project set­up, and tips for maximizing tool performance.

W1210A—Jointer Pal® Magnetic Knife Gauge
(Up to 8", polycarbonate body)
W1211A—Jointer Pal
(Up to 8", all-steel body)

This magnetic knife-setting system lets you set
jointer knives in perfect alignment every time!

Figure 41. W1211A Jointer Pal® Knife Gauge.

D1123—Jointer/Planer Knife Hone

This handy tool sharpens flat and beveled sur­faces quickly and easily. Great for touch-ups.

®

Magnetic Knife Gauge

Figure 40. Instructional reference book.

-36-

Figure 42. D1123 Jointer Knife Hone.

Model G0814/G0814X (Mfd. Since 12/22)

order online at www.grizzly.com or call 1-800-523-4777

1

G10 28 Z 2—1 

⁄2 HP Portable Dust Collector

• Motor:1 1⁄2 HP

• Air suction capacity: 1300 CFM

• Max Static Pressure: 9"

• Inlet: 6" diameter with 4" "Y" adapter

• Impeller:12 3⁄4" Cast aluminum

• Bag capacity: 5.7 Cubic feet

• Portablebasesize:21 1⁄2"x33 1⁄2"

• BagSize:19 1⁄2" x 33"

• CSA Certified

T24736—Carbide Inserts (10 Pack)

These indexable carbide inserts can be rotated to
provide four factory sharp edges before replace­ment. Inserts measure 15 x 15 x 2.5mm.

Figure 44. Replacement carbide inserts for

Model G0814X.

G6 6 97—6" x 1" x 1⁄8" HSS Jointer Knives,
Set of 3

These jointer knives are made from M-2 high
speed steel and are hardened to 62–64 Rockwell
and tempered in a salt bath. All sets are balanced
to within one gram.

Figure 43. G1028Z2 1 1⁄2 HP Portable Dust

Collector.

Figure 45. G6697 Replacement Knives for

Model G0814.

Model G0814/G0814X (Mfd. Since 12/22)

-37-

SECTION 6: MAINTENANCE

To reduce risk of shock or
accidental startup, always
disconnect machine from

The cleaning process for this machine is simple.
Vacuum excess wood chips and sawdust, and
wipe off the remaining dust with a dry cloth. If any
resin has built up, use a resin dissolving cleaner
to remove it. Treat all unpainted cast iron and steel
with a non-staining lubricant after cleaning.

Cleaning &

Protecting

power before adjustments,
maintenance, or service.

Schedule

For optimum performance from this machine, this
maintenance schedule must be strictly followed.

Ongoing

To minimize your risk of injury and maintain proper
machine operation, shut down the machine imme­diately if you ever observe any of the items below,
and fix the problem before continuing operations:

• Loose mounting bolts.

• Dust or debris on and around machine.
Dull or damaged cutterhead knives/inserts.

•
Unprotected cast-iron surfaces.

•
Worn or damaged wires.

•
Any other unsafe condition.

•

Monthly Check

• V-belt tension, damage, or wear (Page 50).

• Clean/vacuum dust buildup from inside cabi-

net and off motor.

Protect the unpainted cast iron surfaces on the
table by wiping the table clean after every use—
this ensures moisture from wood dust does not
remain on bare metal surfaces.

Keep tables rust-free with regular applications of
quality lubricants.

G5562—SLIPIT® 1 Qt. Gel
G5563—SLIPIT® 11 Oz. Spray

-38-

Figure 46. Recommended products for

protecting unpainted cast-iron and steel.

Model G0814/G0814X (Mfd. Since 12/22)

Lubrication

Since all bearings are sealed and permanently
lubricated, simply leave them alone until they
need to be replaced. DO NOT lubricate them.

It is essential to clean components before lubri­cating them because dust and chips build up on
lubricated components and make them hard to
move. Simply adding more grease to them will not
yield smooth moving components.

Clean the components below with mineral spirits
or other oil/grease solvent cleaner and shop rags.

SB1365—South Bend Way Oil-ISO 68

Table Ways

Oil Type ................ SB1365 or ISO 68 Equivalent

Oil Amount
Lubrication Frequency

Lower infeed and outfeed tables to access ways.
Place a couple of drops of oil at top of each way,
at both front and rear of machine, and move tables
up and down to distribute oil (see Figure
Wipe off excess oil.

...........................................1–2 Drops

....................... As Needed

49).

Figure 47. Recommended product for machine

lubrication.

Outfeed Table Leadscrew

Oil Type ................ SB1365 or ISO 68 Equivalent

Oil Amount

Frequency.......................................... As Needed

Lubricate the outfeed table leadscrew with light
machine oil as needed (see Figure 48). Wipe off
excess oil and sawdust with a cloth.

............................................Thin Coat

Figure 49. Example of location to lubricate table

ways.

Fence

Oil Type ................ SB1365 or ISO 68 Equivalent

Oil Amount
Lubrication Frequency

Place one or two drops of light machine oil on
fence pivot points (see Figure 50) as needed.

...........................................1–2 Drops

....................... As Needed

Figure 48. Leadscrew lubrication location.

Model G0814/G0814X (Mfd. Since 12/22)

Figure 50. Fence lubrication locations.

-39-

Review the troubleshooting procedures in this section if a problem develops with your machine. If you need
replacement parts or additional help with a procedure, call our Technical Support.

the

serial number and manufacture date of your machine before calling.

SECTION 7: SERVICE

Troubleshooting

Motor & Electrical

Symptom Possible Cause Possible Solution

Machine does not
start or a breaker
trips immediately
after startup.

Machine stalls or is
underpowered.

Machine has
vibration or noisy
operation.

1. Switch disabling key removed.

2. Incorrect power supply voltage/circuit size.

3. Power supply circuit breaker tripped/fuse
blown.

4. Motor wires connected incorrectly.

5. Wiring open/has high resistance.

6. ON/OFF switch at fault.

7. Centrifugal switch at fault.

8. Start capacitor at fault.

9. Motor at fault.

1. Workpiece material not suitable.

2. Excessive feed rate.

3. Excessive cutting depth.

4. Dull knives/inserts.

5. Dust collection problem, causing internal
components to clog up with shavings.

6. Belt slipping; oil/grease on belt.

7. Pulley loose or not properly aligned.

8. Motor overheated.

9. Motor wires connected incorrectly.

1. Motor or other component loose.

2. Belt worn/loose; belt slapping cover.

3. Pulley loose or not properly aligned.

4. Motor fan rubbing on fan cover.

5. Foot-pedal caster engaged.

6. Dull knives/inserts.

7. Cutterhead bearings at fault.

8. Centrifugal switch at fault.

9. Motor bearings at fault.

1. Install switch disabling key.

2. Ensure correct power supply voltage/circuit size.

3. Ensure circuit is sized correctly and free of shorts.
Reset circuit breaker or replace fuse.

4. Correct motor wiring connections (Page 56).

5. Check/xbroken,disconnected,orcorrodedwires.

6. Test/replace switch.

7. Adjust/replace centrifugal switch if available.

8. Test/replace capacitor.

9. Test/repair/replace.

1. Ensure workpiece is suitable for jointing (Page 28).

2. Reduce feed rate.

3. Reduce cutting depth (Page 29).

4. Sharpen/replace knives (Page 42); rotate/replace
inserts (Page 44).

5. Clear blockages; move machine closer to dust
collector; upgrade dust collector.

6. Tension/replace belt (Page 50); clean belt; ensure
pulleys are aligned (Page 51).

7. Re-align pulleys (Page 51); replace shaft key;
tighten pulley set screw(s).

8. Clean motor, let cool, and reduce depth of cut.

9. Correct motor wiring connections (Page 56).

1. Replace damaged bolts/nuts; retighten loose bolts/

nuts.Usethread-lockinguidifconditionrepeats.

2. Tension/replace belt (Page 50).

3. Re-align pulleys (Page 51); replace shaft key;
tighten pulley set screw(s).

4. Fix/replace fan cover; replace loose/damaged fan.

5. Release foot-pedal caster to stabilize machine.

6. Sharpen/replace knives (Page 42); rotate/replace
inserts (Page 44); set knife/insert alignment/height
correctly (Pages 42 & 44).

7. Replace bearing(s)/realign cutterhead.

8. Replace.

9. Test by rotating shaft; rotational grinding/loose shaft
requires bearing replacement.

Note: Please gather

-40-

Model G0814/G0814X (Mfd. Since 12/22)

Machine Operation

Symptom Possible Cause Possible Solution

Table(s)difcultto

adjust.

Excessive snipe
(gouge in end of
board that is uneven
with rest of cut).

Workpiece stops in
middle of cut.

Workpiece chipping,
tear-out, or overall
rough cuts.

Fuzzy grain. 1. Wood has high moisture content.

Long lines or ridges
that run along length
of workpiece.

1. Table lock(s) engaged/partially engaged.

2. Infeed table stop blocking upward
movement.

1. Outfeed table set too low, or knives/inserts
set too high.

2. Operator pushing down on trailing end of
workpiece as it leaves cutterhead.

1. Outfeed table set too high. 1. Align outfeed table with cutterhead knife/insert at

1. Not feeding workpiece to cut "with the
grain."

2. Dull knives/inserts.

3. Workpiece not suitable for jointing.

4. Nicked or chipped knives/inserts.

5. Feeding workpiece too fast.

6. Excessive cut depth.

7. Lack of proper dust collection or clogged
dust port.

2. Dull knives/inserts.

1. Nicked or chipped knives/inserts. 1. Replace knives (Page 42); rotate/replace inserts

1. Completely loosen table lock(s) (Page 4).

2. Loosen/reset infeed table stop bolt (Page 29).

1. Align outfeed table with cutterhead knife/insert at

top dead center (Page 46); adjust height of knives/
inserts evenly with outfeed table (Page 42).

2. Reduce/eliminate downward pressure on trailing
end of workpiece as it leaves cutterhead.

top dead center (Page 46).

1. Turn the workpiece 180° before feeding again.

2. Sharpen/replace knives (Page 42); rotate/replace
inserts (Page 44).

3. Ensure workpiece is suitable for jointing (Page 28).

4. Replace knives (Page 42); rotate/replace inserts
(Page 44).

5. Reduce feed rate.

6. Reduce cut depth (Page 29).

7. Clear blockages, ensure dust collector is operating

efciently;upgradedustcollector.

1. Ensure wood moisture content is less than 20%.
Allow to dry if necessary (Page 28).

2. Sharpen/replace knives (Page 42); rotate/replace
inserts (Page 44).

(Page 44).

Uneven cutter
marks, wavy
surface, or chatter
marks across face
of workpiece.

Glossy surface;
scorching or
burn marks on
workpiece.

Workpiece is
concave or convex
along its length after
jointing.

1. Feeding workpiece too fast.

2. Knives/inserts not properly adjusted.

1. Dull knives/inserts.

2. Feed rate too slow.

1. Workpiece not held with even pressure
against outfeed table during cut.

2. Workpiece too uneven at start of operation.

3. Outfeed table not parallel with infeed table.

1. Reduce feed rate.

2. Properly adjust knives/inserts (Page 42).

1. Sharpen/replace knives (Page 42); rotate/replace
inserts (Page 44).

2. Increase feed rate.

1. Apply even downward pressure against workpiece
throughout entire travel along outfeed side during
cut.

2. Take partial cuts to remove extreme high spots
before doing a full pass.

3. Check/Adjust table parallelism (Page 52).

Model G0814/G0814X (Mfd. Since 12/22)

-41-

Setting/Replacing

Setting the knives correctly is crucial to the proper
operation of the jointer and

important
role in keeping the knives sharp. If one knife is
higher than the others, it will do the majority of the
work, and thus,

The knife jig included with the jointer is designed
to set

at the correct

height

Th

with
jack screws that allow for careful positioning of
the knives.

The cutterhead on this jointer comes with both
jack screws and springs for setting knife height.
Which one you choose is a matter of personal
preference. However, only one of these options is
needed to set the knives.

There are two options for setting the knives—the
straightedge method and the knife-setting jig
method. Each option has advantages and disad­vantages; the correct one for you will be a mat­ter of personal preference. For best results, the
tables must be parallel with each other (refer to
Checking/Adjusting Table Parallelism) and the
outfeed table height must be properly set (refer to

Setting Outfeed Table Height

Straightedge Method

A high quality straightedge (or Jointer Pal) is held
flat against the outfeed table and the knife heights
are set to the bottom of the straightedge, as
shown. Because the knife projection height from
the cutterhead is dependent on the outfeed table
height, the outfeed table must be set as described
in

for this method

to work correctly.

When using the straightedge method to set the
knives, you will not need to move the outfeed
table once it is set and you will always be assured
that the knives are even with the outfeed table in
their highest point of rotation (TDC)—even if the
cutterhead is not perfectly parallel with the out-

To check knife height with a straightedge:

1.

2.

3.

Knives (G0814)

DISCONNECT MACHINE FROM POWER!

Remove cutterhead guard or block it open.

it plays an

become dull much faster.

all the knives evenly and

in the cutterhead.

e cutterhead in this jointer is equipped

).

Using a straightedge on outfeed table, check

height of each knife at positions as shown.

Black Lines Represent
Straightedge Positions
From Overhead View

Knife at TDC

Straightedge

Outfeed Infeed

Setting Outfeed Table Height

Item(s) Needed Qty

Precision Straightedge or Knife-Setting Jig ...... 1

Hex Wrench 3mm

Open-End Wrench 8mm.................................... 1

-42-

.............................................. 1

Figure 51. Setting knife height with a straightedge.

Figure 52. Setting knife height with a Jointer Pal®.

— Knives are set correctly when they just

touch bottom of straightedge at TDC in
each of straightedge positions.

— If knives do not touch straightedge or they

lift up at any position, then those knives
need to be adjusted (refer to Setting/
Replacing Knives on Pag

Model G0814/G0814X (Mfd. Since 12/22)

e 43).

To check knife height with a knife-setting jig:

1.

2.

3.

4.

knife.

Knife-Setting Jig Method

The infeed table is lowered to fit the jig on the
cutterhead, as shown, and the knife heights
are set to just touch the middle pad of the jig.
The knife

-setting

jig included with the jointer is

designed to set

at the

correct height in the cutterhead.

Setting/Replacing Knives

1.

2. Remove cutterhead guard from table and

" on depth-of-cut

scale. This will provide unrestricted access to

3.

4. Rotate cutterhead pulley to provide good

access to cutterhead knives.

To check knife height with a knife-setting jig:

1. DISCONNECT MACHINE FROM POWER!

2. Remove cutterhead guard or block it open.

3. Lower infeed table to

1

⁄2" scale mark.

4. Place knife jig on cutterhead, directly over a

knife.

5. Closely examine how jig touches cutterhead

and knife. Knife is set correctly when, on
each side of cutterhead, both legs of jig sit
firmly on cutterhead body and middle pad of

— If jig does not sit as described, then that

Repeat this inspection

with other knives before resetting.

5. Loosen cutterhead gib bolts, starting in the

middle, and alternating back and forth until all

The first time you set or replace a knife,

lean
gib and clean inside cutterhead slot to remove
all pitch or sawdust. Coat knife and gib with a
metal protectant.

all the knives evenly and

Middle

Pad

Figure 53. Example of knife-setting jig positioned

over cutterhead knife.

Loosen
Tighten

Knife

jig just touches top edge of knife.

knife must be reset.

Figure 55. Using knife-setting jig to set knife

height.

Gib Bolt

Gib

Jack

Screw

Figure 54. Cutterhead profile diagram.

DISCONNECT MACHINE FROM POWER!

Remove cutterhead guard or block it open.

Lower infeed table to 1⁄2" scale mark.

Place knife jig on cutterhead, directly over a

Model G0814/G0814X (Mfd. Since 12/22)

DISCONNECT MACHINE FROM POWER!

lower infeed table to 1⁄2

cutterhead.

Remove cabinet rear access panel to expose

cutterhead pulley.

gib bolts are loose, but not falling out.

remove gib and knife from cutterhead. C

-43-

5. Loosen cutterhead gib bolts, starting in the

middle, and alternating back and forth until all
gib bolts are loose, but not falling out.

The first time you set or replace a knife,

remove gib and knife from cutterhead. Clean
gib and clean inside cutterhead slot to remove
all pitch or sawdust. Coat knife and gib with a
metal protectant.

6. Position knife jig over knife. Loosen gib bolts

until knife is completely loose.

7. Access jack screws through holes in cut-

terhead. Using a hex wrench, rotate jack
screws to raise or lower knife. When knife is
set correctly, it will barely touch middle pad of
knife jig or bottom of straightedge in each of
the straightedge positions. Snug gib bolts just
tight enough to hold knife in place. Repeat
with remaining knives.

8. Rotate cutterhead to reveal the first knife

you started with. Lightly snug all gib bolts,
alternating from one side to the other, and
working from the ends to the middle. Repeat
with remaining knives.

5. Loosen cutterhead gib bolts, starting in the

middle, and alternating back and forth until all
gib bolts are loose, but not falling out.

The first time you set or replace a knife,

remove gib and knife from cutterhead. Clean
gib and clean inside cutterhead slot to remove
all pitch or sawdust. Coat knife and gib with a
metal protectant.

6. Position knife jig over knife. Loosen gib bolts

until knife is completely loose.

7. Access jack screws through holes in cut-

terhead. Using a hex wrench, rotate jack
screws to raise or lower knife. When knife is
set correctly, it will barely touch middle pad of
knife jig or bottom of straightedge in each of
the straightedge positions. Snug gib bolts just
tight enough to hold knife in place. Repeat
with remaining knives.

8. Rotate cutterhead to reveal the first knife

you started with. Lightly snug all gib bolts,
alternating from one side to the other, and
working from the ends to the middle. Repeat
with remaining knives.

9. Tighten each gib bolt in the same alternating

10. Make sure outfeed table is set even with the

11.

rear

access panel.

5. Loosen cutterhead gib bolts, starting in the

middle, and alternating back and forth until all
gib bolts are loose, but not falling out.

The first time you set or replace a knife,

remove gib and knife from cutterhead. Clean
gib and clean inside cutterhead slot to remove
all pitch or sawdust. Coat knife and gib with a
metal protectant.

6. Position knife jig over knife. Loosen gib bolts

until knife is completely loose.

7.

terhead. Using a hex wrench, rotate jack
screws to raise or lower knife. When knife is
set correctly, it will barely touch middle pad of
knife jig or bottom of straightedge in each of
the straightedge positions. Snug gib bolts just
tight enough to hold knife in place. Repeat
with remaining knives.

Rotating/Replacing

Access jack screws through holes in cut-

-44-

Figure 56. Jack screw access hole.

3

Figure 57. Gib bolt tightening sequence.

manner as you did in the previous step.

new knives at top dead center.

Replace cutterhead guard and cabinet

1

42

Helical Cutterhead

Inserts (G0814X)

The Model G0814X V-helical cutterhead is
equipped with 4-sided indexable carbide inserts.
Each insert can be removed, rotated, and re­installed to use any of its four cutting edges. If one
cutting edge becomes dull or damaged, simply
rotate it 90º (see Figure 58) to use a sharp cut­ting edge.

Reference Number

Figure 58. Insert rotating sequence.

The inserts have a reference number on each
corner. The position of the reference number on
installed inserts can be used to track which edges
are sharp/unused and which edges are dull or
damaged. Replace inserts once reference num­ber has been rotated back to its original position.

Item(s) Needed

Heavy Leather Gloves .......................... 1 Pair

•

Safety Glasses (per person)........................ 1

•
Flat Hd Torx Screws

•

T20 M6-1 x 15 ..............................As Needed

Indexable Carbide Inserts

•

15 x 15 x 2.5mm ...........................As Needed

Torx Bit T-20 1⁄4" Shank ................................ 1

•

T-Handle Bit Driver 1⁄4" ................................. 1

•

Phillips Head Screwdriver #2 ...................... 1

•

Wrench or Socket 1⁄2 " .................................. 1

•

Hex Wrench 3mm ........................................ 1

•

Torque Wrench 0–50 in.-lb. ......................... 1

•

Clean Shop Rags .........................As Needed

•

Degreaser .....................................As Needed

•

Light Machine Oil .........................As Needed

•

Model G0814/G0814X (Mfd. Since 12/22)

Cutterhead inserts are extremely sharp.
Wear heavy leather gloves to avoid the risk
of serious personal injury during the follow­ing steps.

To replace or rotate an indexable insert:

1. DISCONNECT MACHINE FROM POWER!

Set fence to 90° and move it all the way back.

2.

Remove cutterhead guard, and lower infeed

3.

table as far down as it will go.

Remove belt guard to access V-helical

4.

cutterhead pulley.

Rotate pulley as needed to make inserts

5.

accessible for removal or rotation.

Remove any sawdust from head of carbide

6.

insert Torx screw.

Clean all dust and dirt off insert and cutterhead

9.

pocket from which insert was removed, and
replace insert so a fresh, sharp edge is facing
outward.

— If all four insert cutting edges have been

used, replace insert with a new one.
Always position reference dot in same
position when installing a new insert to aid
in rotational sequencing.

Note: Proper cleaning is critical to achiev-

ing a smooth finish. Dirt or dust trapped
between insert and cutterhead will slightly
raise insert, and make noticeable marks on
your workpieces the next time you cut.

Lubricate Torx screw threads with a light

10.

machine oil, wipe excess oil off threads, and
torque Torx screw to 48–50 inch pounds.

Note: Excess oil may squeeze between insert

and cutterhead or in screw hole, thereby
lifting insert or screw slightly and affecting
workpiece finishes.

Put on heavy leather gloves to protect fingers

7.

and hands.

8. Remove Torx screw and indexable insert (see
Figure 59).

Torx

Screw

Cutterhead

Insert

Figure 59. Example of cutterhead inserts and

Torx screws.

11. Install belt guard and raise infeed table.

12. Install cutterhead guard back over cutterhead,

making sure that spring tension in guard
is properly set so guard springs back over
cutterhead when it is pulled back and released.

If guard does not snap back, or snaps back

—

slowly, proceed to Checking/Adjusting
Cutterhead Guard on Page 53.

Model G0814/G0814X (Mfd. Since 12/22)

-45-

Setting Outfeed

Table Height

To help ensure safe operation and best cutting
results, set the outfeed table height level with the
knives/inserts when they are at top-dead-center
(TDC).

If the outfeed table is set too low, the workpiece
will be tapered from front to back or there will be
snipe (a gouge in the end of the board that is
uneven with the rest of the cut). If the outfeed table
is set too high, the workpiece will hit the edge of
the outfeed table during operation, increasing the
chance of kickback.

Item(s)

Precision Straightedge 3'................................... 1

Phillips Head Screwdriver #2
Open-End Wrenches 12mm

To set outfeed table height:

1.

Needed Qty

............................ 1

.............................. 2

DISCONNECT MACHINE FROM POWER!

Cutterhead knives/inserts are extremely
sharp. Wear heavy leather gloves to avoid
the risk of serious personal injury during
the following steps.

3. G0814 Only: Make sure knife heights are set

correctly (refer to Setting/Replacing Knives
on Page

Loosen outfeed table lock (see Figure 60).

4.

Outfeed

Table

Lock

42).

Infeed

Table

Lock

2. Remove cutterhead guard, fence, and

cabinet rear access panel.

Figure 60. Location of table locks.

5. Place straightedge on outfeed table so it

extends over cutterhead.

-46-

Model G0814/G0814X (Mfd. Since 12/22)

The depth scale can be calibrated or "zeroed" to
make sure the cutting depth shown on the scale
matches the actual cutting depth (per pass).

6.

Top Dead

Center

Use motor pulley to rotate cutterhead until

one knife or insert is at TDC (its highest point
during rotation), as shown in

Figures 61–62.

Calibrating Depth

Scale

Top Dead

Center

G0814X

Figure 61. Knife or insert at TDC.

Straightedge

Outfeed Infeed

G0814

G0814

Before beginning, set outfeed table height as
described in Setting Outfeed Table Height.

Tools Needed Qty

Straightedge ...................................................... 1

Phillips Head Screwdriver #2
Open-End Wrench 12mm

To calibrate depth scale:

1. DISCONNECT MACHINE FROM POWER!

Place straightedge across infeed and outfeed

2.

tables (see Figure 63).

G0814

............................ 1

.................................. 1

G0814X

Straightedge

Outfeed Infeed

Figure 62. Using straightedge to check outfeed

table height.

7. Use outfeed table handwheel to set outfeed

table so knife or insert barely touches straight­edge, as shown in

Tighten outfeed table lock so outfeed table

8.

will not move during operation.

Re-install cutterhead guard, fence, and

9.

cabinet rear access panel.

Figure 62.

Straightedge

InfeedOutfeed

G0814X

Straightedge

InfeedOutfeed

Figure 63. Infeed table adjusted even with

outfeed table.

Model G0814/G0814X (Mfd. Since 12/22)

-47-

3. Loosen jam nut on table stop bolt (see Figure

64) and unthread it several turns.

Adjusting Gibs

Depth

Indicator

Scale

Stop Bolt

Jam Nut

Figure 64. Example of depth indicator set to "0".

4. Adjust infeed table until it is level with outfeed

table.

5. Using a screwdriver, precisely adjust scale

pointer to “0”, then thread stop bolt into table
and secure with jam nut.

The function of the table gibs is to eliminate
excessive play in the table movement. The gibs
also control how easy it will be to move the tables
up and down.

Tools Needed Qty

Open-End Wrench 12mm .................................. 1

Hex Wrench 4mm

To adjust table gibs:

1. Loosen two infeed table gib nuts on front of

jointer base (see Figure 65).

.............................................. 1

Gib Nut

Gib Set Screw

Figure 65. Example of infeed table gib controls.

2. Oil table ways and outfeed leadscrew if

needed (see Page 39).

Evenly tighten gib set screws a small amount,

3.

then check table by moving it up and down.
Adjust set screws as needed until friction of
table movement is balanced between mini­mal play and ease of movement.

Note: Tighter gibs reduce play but make it

harder to adjust tables.

Repeat Steps 1–3 with outfeed table.

4.

Set outfeed table height as described in

5.
Setting Outfeed Table Height on Page 46.

-48-

Model G0814/G0814X (Mfd. Since 12/22)

Setting Fence Stops

The fence stops simplify the task of adjusting the

fenceto90˚and135˚(45˚outward).

Tools Needed Qty

45° Square......................................................... 1

90° Square
Sliding Bevel
Open-End Wrench 12mm

Setting 90° Fence Stop

1. Usea90˚squaretoadjustfenceto90˚(see

Figure 66).

........................................................ 1

...................................................... 1

.................................. 1

Setting 135° Fence Stop

1. Disengage swing stop (see Figure 67).

Useaslidingbeveladjustedto135˚toadjust

2.

fence to 135˚ (45˚ outward) position, as

shown in Figure 68.

Figure 68.Exampleofadjustingfence45˚

outward.

Figure 66.Exampleofadjustingfenceto90˚.

2. Flip 90˚ swing stop into position shown in

Figure 67.

3. Loosen jam nut on 90˚ fence stop bolt (see

Figure 67).

Fence Stop Bolt

Jam Nut

Swing Stop

3.

 Loosen jam nut on 135˚ stop bolt (see

Figure 69).

135° Stop Bolt

Jam Nut

Figure 69.Locationof135˚stopboltand

jam nut.

 Adjust 135˚ stop bolt until it makes contact

4.

with back of fence.

Figure 67.90˚swingstopengaged.

4. Adjust the 90˚ fencestop boltuntil itmakes

contactwith90˚swingstop.

5. Retighten jam nut loosened in Step 3.

Model G0814/G0814X (Mfd. Since 12/22)

Retighten jam nut loosened in Step 3.

5.

-49-

Tensioning/

Replacing V-Belt

To ensure optimum power transmission from
the motor to the cutterhead, the V-belt must be
in good condition (free from cracks, fraying and
wear) and properly tensioned.

After approximately 16 hours of opera­tion, belts will stretch and seat into pul­ley grooves. The belts need to be re-ten­sioned after this initial break-in period
to ensure optimum power transfer and
maximum overall life of the belts.

Item(s) Needed Qty

Phillips Head Screwdriver #2 ............................ 1

Open-End or Socket Wrench 12mm

Tensioning Belt

1. DISCONNECT MACHINE FROM POWER!

2. Remove cabinet rear access panel.

................. 1

Belts and pulleys will be hot after operation.
Allow them to cool before handling.

5.

Press belt with moderate pressure in center to

check belt tension. Belt is correctly tensioned
when there is approximately
when pushed, as shown in Figure 71.

— If there is more than 1⁄4" deflection when

you check belt tension, repeat the tension­ing procedure until it is correct.

Cutterhead Pulley

Approximately

1

/4" Deflection

Motor Pulley

Figure 71. Correct belt deflection when properly

tensioned.

1

⁄4" deflection

3. Loosen motor mount hex nuts shown in
Figure 70. DO NOT completely remove nuts.

x 4

Figure 70. Location of motor mount hex nuts.

Press down on motor to keep tension on belt.

4.

6.

Tighten motor mount hex nuts (see Figure 70)

6. Tighten motor mount hex nuts (see Figure 70)

and replace cabinet rear access panel.

and replace cabinet rear access panel.

Replacing Belt

1. DISCONNECT MACHINE FROM POWER!

2. Remove cabinet rear access panel and belt

guard.

Loosen motor mount hex nuts shown in

3.
Figure 70.

Have another person lift motor as you remove

4.

belt and replace it with a new one. Make sure
ribs of belt are seated in pulley grooves.

Follow Steps 4–5 in Tensioning Belt proce-

5.

dure to set correct belt tension.

Tighten motor mount hex nuts (see

6.
Figure

panel and belt guard.

70), and replace cabinet rear access

-50-

Model G0814/G0814X (Mfd. Since 12/22)

Aligning Pulleys

Pulley alignment is another important factor in
power transmission and belt life. The pulleys
should be parallel to each other and in the same
plane (coplanar) for optimum performance.

The pulleys can be adjusted by loosening the
pulley set screws, aligning the pulleys, and
retightening the set screws.

Straightedge

Item(s) Needed Qty

Hex Wrench 3mm .............................................. 2

Straightedge

To align pulleys:

DISCONNECT MACHINE FROM POWER!

1.

2. Remove cabinet rear access panel and belt

guard.

Place straightedge against pulleys to check

3.

their alignment (see Figure 72).

Note: This can also be done visually (without

a straightedge) if you do not have a straight­edge available that will fit; however, the
most accurate results will come from using a
straightedge.

...................................................... 1

Cutterhead

Pulley

Alignment

Motor

Pulley

Figure 72. Example of checking pulley

alignment.

— If they are not aligned, loosen set screws

on cutterhead or motor pulley as needed
to align pulleys, then tighten set screws
(see Figure 73).

Model G0814/G0814X (Mfd. Since 12/22)

x 2

Pulley

Figure 73. Motor pulley set screw locations.

Replace cabinet rear access panel and belt

4.

guard.

-51-

Checking/Adjusting

The infeed and outfeed tables must be parallel
with each other in order to produce a straight,
jointed edge. When the tables are not parallel
with each other, the jointer will produce workpiec­es that are cupped (concave) or bowed (convex)
along their length.

Table parallelism is factory-set, and should not
normally need to be adjusted when the machine
is new. However, after prolonged use, or if
machine has been jarred during lifting or trans­portation, it may become necessary to adjust the
table parallelism.

Table parallelism is adjusted by inserting shims
between the dovetailed ways of the outfeed table
to make it parallel with the infeed table. Once
this adjustment is made, the outfeed table height
should not need to be adjusted again.

To check/adjust table parallelism:

1.

2.

3. Set outfeed table height as described in

4.

ger at TDC, extend straightedge over both
tables, raise infeed table until it contacts

), then lock infeed

table.

5. Look down length of straightedge on outfeed

side to see if there are any noticeable gaps
between straightedge and outfeed table. Do

— If there are no gaps, and the straightedge

makes full contact with both tables at front
and rear, the tables are parallel with each

— If there are gaps anywhere between one

of the tables and the straightedge, the
tables are not parallel to each other and

6. Insert feeler gauge between table and

straightedge where gap is greatest (see

). Maximum allowable tolerance is

0.003".

7. Loosen outfeed table lock(s). Place shims

between dovetailed ways, as shown, until

of parallel with

infeed table at front and rear of tables.

8. Re-check outfeed table height (refer to

), and re-ad-

just if necessary.

Table Parallelism

Item(s) Needed Qty

Straightedge 4–8' .............................................. 1

Feeler Gauge Set
Metal Shims

.............................................. 1

....................................... As Needed

this at both front and rear of table.

other and no adjustments are necessary.

must be adjusted. Proceed to Step 6.

Figure

Insert Feeler Gauge

Where Gap is Greatest

Straightedge

Outfeed

Figure 75. Example of feeler gauge location for

checking table parallelism.

Infeed

DISCONNECT MACHINE FROM POWER!

Move cutterhead guard out of the way.

Setting Outfeed Table Height.

Rotate cutterhead until knife/insert is no lon-

straightedge (see Figure

Straightedge

Figure 74. Checking table parallelism.

-52-

outfeed table is within 0.003"

Possible Shim

Locations

Figure 76. Example of typical locations to place

shims when adjusting table parallelism.

Infeed Outfeed

Setting Outfeed Table Height

Model G0814/G0814X (Mfd. Since 12/22)

Checking/Adjusting

Cutterhead Guard

The cutterhead guard is a critical safety
feature of this jointer. You MUST verify its
operation before using the jointer! Failure
to properly install this guard will greatly
increase risk of serious personal injury.

The cutterhead guard is designed to reduce the
risk of accidental contact with hands or fingers
with the spinning cutterhead. When properly
installed and functioning correctly, the guard auto­matically rotates clear of the cutterhead during the
cutting operation and then springs back over the
cutterhead as soon as the operation is complete.

To check/adjust cutterhead guard:

. DISCONNECT MACHINE FROM POWER!

1

Pull cutterhead guard away from fence and

2.

let it go (see Figure 77).

If cutterhead guard does spring back over

—

cutterhead, contacts fence, and does not
drag across infeed table, then cutterhead
guard is properly adjusted.

If cutterhead guard does not spring back

—

over cutterhead, does not contact fence,
or drags across infeed table, proceed to
Step 3.

Cutterhead Guard

In order to function as intended, the guard must
be installed as low as possible over the infeed
table without actually touching it (approximately

1

⁄16 " above infeed table), and it must have enough

spring tension at the mounting shaft to quickly
reposition itself against the fence after it is rotated
away from the cutterhead and released. Before
performing rabbeting operations, adjust guard
height to just clear outfeed table.

Item(s)

Additional Person .............................................. 1

Precision Ruler 6"
Phillips Head Screwdriver #2
Hex Wrench 3mm
Scrap Wood

Needed Qty

.............................................. 1

............................ 1

.............................................. 1

....................................... As Needed

Figure 77. Example of cutterhead guard

components.

Model G0814/G0814X (Mfd. Since 12/22)

-53-

Remove fence locking nut on fence lock

3.

handle, then remove handle, flat washer, and
fence assembly (see Figure 78).

Top View

Fence

Flat

Washer

Lock

Alignment Area

Carriage

Cutterhead

Guard

Carriage

Support

Key

Bottom View

Fence

Locking

Nut

Figure 78. Fence component locations.

4. Loosen Phillips head screw on cutterhead

guard shaft, and set screw in rabbeting table
(see Figure 77).

Note: Back off set screw so it is no longer

contacting cutterhead guard shaft.

Fence

Carriage

Base

Figure 79. Cutterhead guard aligned with

carriage.

6.

Rotate cutterhead guard counterclockwise

and secure temporarily with a piece of scrap
wood (see Figure 79).

Scrap
Wood

Figure 80. Example of cutterhead guard secured

in place.

Align corner of cutterhead guard with edge

5.

of carriage (see Figure 79), raise guard 1⁄16 "
above infeed table, then secure set screw
and Phillips head screw loosened in Step 4.

-54-

Place carriage support key and fence onto

7.

fence carriage base, making sure fence
fits over key, and insert fence lock with flat
washer on top through carriage, then secure
with fence locking nut (see Figure 78).

Remove scrap wood installed in Step 6 and

8.

repeat Step 2. If necessary, repeat Steps 3–8
until cutterhead guard is properly adjusted.

Model G0814/G0814X (Mfd. Since 12/22)

These pages are current at the time of printing. However, in the spirit of improvement, we may make chang­es to the electrical systems of future machines. Compare the manufacture date of your machine to the one
stated in this manual, and study this section carefully.

If there are differences between your machine and what is shown in this section, call Technical Support at
[phone] for assistance BEFORE making any changes to the wiring on your machine. An updated
wiring diagram may be available.

number and manufacture date of your

machine before calling. This information can be found on the main machine label.

SECTION 8: WIRING

Note: Please gather the serial

Wiring Safety Instructions

SHOCK HAZARD. Working on wiring that is con-

nected to a power source is extremely dangerous.
Touching electrified parts will result in personal
injury including but not limited to severe burns,
electrocution, or death. Disconnect the power
from the machine before servicing electrical com­ponents!

MODIFICATIONS. Modifying the wiring beyond
what is shown in the diagram may lead to unpre­dictable results, including serious injury or fire.
This includes the installation of unapproved after­market parts.

WIRE CONNECTIONS. All connections must
be tight to prevent wires from loosening during
machine operation. Double-check all wires dis­connected or connected during any wiring task to
ensure tight connections.

CIRCUIT REQUIREMENTS. You MUST follow
the requirements at the beginning of this manual
when connecting your machine to a power source.

WIRE/COMPONENT DAMAGE. Damaged wires
or components increase the risk of serious per­sonal injury, fire, or machine damage. If you notice
that any wires or components are damaged while
performing a wiring task, replace those wires or
components.

MOTOR WIRING. The motor wiring shown in
these diagrams is current at the time of printing
but may not match your machine. If you find this
to be the case, use the wiring diagram inside the
motor junction box.

CAPACITORS/INVERTERS. Some capacitors
and power inverters store an electrical charge for
up to 10 minutes after being disconnected from
the power source. To reduce the risk of being
shocked, wait at least this long before working on
capacitors.

EXPERIENCING DIFFICULTIES. If you are expe­riencing difficulties understanding the information
included in this section, contact our Technical
Support at [phone].

The photos and diagrams
included in this section are
best viewed in color. You
can view these pages in
color at www.grizzly.com.

Model G0814/G0814X (Mfd. Since 12/22)

-55-

110 VAC

5-15 Plug

GND

110V Wiring Diagram

Neutral

Hot

Ground

ON/OFF Switch

(Viewed from Behind)

KEDU
HY-18

20/12A

125/250V

Figure 81. Motor junction box.

MOTOR

GND

Figure 82. ON/OFF switch wiring

(viewed from behind).

Ground

Motor Junction Box

Start Capacitor

300MFD
125VAC

-56-

READ ELECTRICAL SAFETY

ON PAGE 55!

Model G0814/G0814X (Mfd. Since 12/22)

220V Wiring Diagram

Hot

ON/OFF Switch

(Viewed from Behind)

GND

Hot

Ground

125/250V

KEDU
HY-18

20/12A

GND

G

6-15 Plug

220VAC

Indicates wiring

changes for

220V conversion

MOTOR

Figure 83. ON/OFF switch wiring

(viewed from behind).

Model G0814/G0814X (Mfd. Since 12/22)

Ground

Motor Junction Box

Start Capacitor

300MFD
125VAC

READ ELECTRICAL SAFETY

ON PAGE 55!

-57-

33

55

13

SECTION 9: PARTS

We do our best to stock replacement parts when possible, but we cannot guarantee that all parts shown
are available for purchase. Call [phone] or visit www.grizzly.com/parts to check for availability.

Table

42

41

58

11

32

3

63

8

9

10

40

12

43

6

52

7

25

16

43

51

14

1

36

15

34

62

21V2

62

19V2

29

30

30

34

18V2

2V2

5

39

28

26

60

4

-58-

BUY PARTS ONLI NE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

53

57

60

54

49V2

60

27

35

59

52

61

17

56

Model G0814/G0814X (Mfd. Since 12/22)

Table Parts List

REF PART # DES CRIP TIO N REF PART # DES CRIP TIO N

1 P0814001 TABLE BASE 31 P0814031 FLAT WASHER 3/8
2V2 P0814002V2 INFEED TABLE V2.12. 22 32 P0814032 KEY 3/ 8 X 3/8 X 9
3 P0814003 OUTFEED TABLE 33 P0814033 ROLL PIN 4 X 12
4 P0814004 GIB 34 P0814034 FLAT WASHER 3/8
5 P0814005 TABLE LOCK HANDLE M8-1.25 X 30 35 P0814035 PHLP HD SCR 8-32 X 1/4
6 P0814006 SET SCREW 3/8-16 X 5/ 8 36 P0814036 HEX BOLT 5/16-18 X 2-1/2
7 P0814007 HEX NUT 3/4-16 39 P0814039 ADJ HANDLE 89MM, M8-1.25 X 45
8 P0814008 PIVOT SHAFT 19 X 178MM 40 P0814040 FLAT WASHER 5/16
9 P0814009 HANDWHEEL TYPE-21 123D X 20-B X 5/16-18 41 P0814041 FLAT WASHER #10
10 P0814010 SET SCREW 1/4-20 X 1/4 42 P0814042 PHLP HD SCR 10-24 X 3/8
11 P0814011 OUTFEED TABLE ADJUST BLOCK 43 P0814043 FLAT WASHER 1/2
12 P0814012 OUTFEED TABLE LEADSCREW 49V2 P0814049V2 SET SCREW M6-1 X 20 V2.12.22
13 P0814013 HANDLE 1/2-12, 1-1/2 X 2-1/2 (PLASTIC) 51 P0814051 HEX BOLT 1/4-20 X 1/2
14 P0814014 BELT GUARD 52 P0814052 FLAT WASHER 1/4
15 P0814015 FLAT WASHER 5/16 53 P0814053 BASE ROD 12.5 X 180MM
16 P0814016 LEADSCREW BRACKET 54 P0814054 I NFEED TABLE ADJUST BLOCK
17 P0814017 PHLP HD SCR 1/4-20 X 1/2 55 P0814055 STUD-UDE 1/2-12 X 15-3/4, 3/4, 1-3/8
18V2 P0814018V2 CUTTERHEAD GUARD V2.12.22 56 P0814056 HEX BOLT 5/16-18 X 1-3/4
19V2 P0814019V2 GUARD SHAFT V2.12.22 57 P0814057 HEX NUT 5/16-18
21V2 P0814021V2 TORSION SPRING 2 X 17 X 15 V2.12. 22 58 P0814058 REVOLVING HANDLE 5/16-18, 3/ 4 X 3-1/4
25 P0814025 CAP SCREW 5/16-18 X 1 59 P0814059 PI VOT SHAFT 12.5 X 180MM
26 P0814026 DEPTH-OF-CUT SCALE 60 P0814060 E-CLIP 12MM
27 P0814027 POINTER 61 P0814061 HEX NUT 1/2-12
28 P0814028 NAMEPLATE RIVET 2 X 5 62 P0814062 FLAT WASHER 10 X 16 X 1.5MM
29 P0814029 CARRIAGE MOUNT 63 P0814063 E XT RE TAI NI NG RING 10MM
30 P0814030 HEX BOLT 3/8-16 X 1-1/4

Model G0814/G0814X (Mfd. Since 12/22)

BUY PARTS ONLI NE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

-59-

Fence

129

REF P ART # DES CRIP TIO N REF PART # DESCRI PTI ON

108

101

102

123

117

118

132

133

102

123

122

116

124

106

131

125

126

121

130

111

110

115

112

128

103

113

104

109

105

119

120

114

127

126

101 P0814101 FE NCE 118 P0814118 SWING STOP
102 P0814102 PI VOT STUD 1/2-20 X 5/ 8 119 P0814119 HEX NUT 5/8-18
103 P0814103 FE NCE HI NGE 120 P0814120 FENCE TI LT BUS HI NG
104 P0814104 SET SCREW 3/8-16 X 1-1/2 CONE-PT 121 P0814121 FENCE CARRIAG E
105 P0814105 HEX NUT 3/8-16 122 P0814122 FLAT WASHER 1/2
106 P0814106 TILT LEVER 3/8-16 X 1/2 123 P0814123 FENCE LOCK 1/2-13 X 1-1/ 8
108 P0814108 FLAT HD CAP SCR 5/ 16-18 X 1-5/8 124 P0814124 FENCE TI LT L OCK NUT 1/2-12
109 P0814109 FENCE BRACKET 125 P0814125 HEX BOLT 5/16-18 X 1
110 P0814110 FENCE STOP BRACKET 126 P0814126 HEX NUT 5/16-18
111 P0814111 SHOULDER BOLT 5/16-18 X 112, 3/8 X 3/ 4 127 P0814127 HEX BOLT 5/ 16-18 X 1-3/4
112 P0814112 HEX NUT 7/16-14 128 P0814128 FENCE LOCK BRACKET
113 P0814113 STANDOFF STUD 7/16-14 X 1-1/ 4, 5/8-18, 6-1/2L 129 P0814129 PHLP HD SCR 1/4-20 X 1/2
114 P0814114 FE NCE TI LT CLAMP 130 P0814130 FLAT WASHER 1/4
115 P0814115 STOP TAB-90 DEG 131 P0814131 SUPPORT PI N 1/4 X 1/2 (PLASTIC)
116 P0814116 ROLL PIN 4 X 12 132 P0814132 HEX NUT 1/2-20
117 P0814117 SHOULDER BOLT 5/16-18 X 3/8, 1/ 4 X 3/8 133 P0814133 FLAT WASHER 1/2

-60-

BUY PARTS ONLI NE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

Model G0814/G0814X (Mfd. Since 12/22)

Cutterhead

215

REF PART # DES CRIP TION REF P ART # DESCRI PTION

209

210

208

207

206

202

204

G0814

Only

205

217

201

202

211

G0814X

201

Only

212

222

213

221

214

208

207

206

219

218

218

220

219

203

201 P0814201 CUTTERHEAD 6" 3-KNIFE (G0814) 212 P0814212 BALL BEARING 6203-2RS
201 P0814X201 CUTTERHEAD 6" V-HELICAL (G0814X) 213 P0814213 BEARING BLOCK (RIGHT)
202 P0814202 KNIFE 6" X 1" X 1/8" 3-PC (G0814) 214 P0814214 CUTTE RHEA D PUL LEY
202 P0814X202 INDEXABLE I NSERT 15 X 15 X 2.5MM (G0814X) 215 P0814215 SET SCREW 1/4-20 X 3/ 8
203 G0814X203 FLAT HD TORX SCR T20 M6-1 X 15 217 P0814217 FLAT HD CAP SCR M5-.8 X 12
204 P0814204 KNIFE GIB 218A P0814218A KNIFE-SETTING J I G
205 P0814205 GIB BOLT 1/4-20 X 1/4 W/8MM HEAD 218 P0814218 KNIFE-SETTING JIG FOOT
206 P0814206 HEX NUT 3/8-24 219 P0814219 E-CLIP 9MM
207 P0814207 LOCK WASHER 3/8 220 P0814220 KNIFE-SETTING JIG SHAFT
208 P0814208 STUD-SE 3/18-16 X 3-1/ 2, 3/4" 221 P0814X221 T-HANDLE TORX DRI V ER 1/ 4"
209 P0814209 BEARING BLOCK (LEFT) 222 P0814X222 T-20 TORX BIT
210 P0814210 BALL BEARING 6202-2RS
211 P0814211 KEY 5 X 5 X 30

218A

(G0814 Only)

Model G0814/G0814X (Mfd. Since 12/22)

BUY PARTS ONLI NE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

-61-

Stand

350V2

333V2

334

384V2

328

329

322

393

386V2

327
308

326

331V2

333V2

332

326

316

315

325

390

382

381
380

367

341

366

367

370

378

365

371

366

369

373V2

339

350V2

377

361

368

377

338

362

340

376

377

376

363

364

372V2

371

372

371

319

383

317

318

360AV2

321

312

320

320-9

313

320-1

320-8

320-2

320-5

320-7

306

314

320-3

320-4

320-6

320-10

-62-

BUY PARTS ONLI NE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

Model G0814/G0814X (Mfd. Since 12/22)

REF PART # DES CRIP TIO N REF PART # DES CRIP TIO N

Stand Parts List

306 P0814306 MOTO R MOUNT P LA TE 338 P0814338 WRENCH 8 X 10MM OPEN-ENDS
308 P0814308 SWI TCH CO VE R 339 P0814339 WRENCH 12 X 14MM OPEN-ENDS
312 P0814312 HEX NUT 5/16-18 340 P0814340 HEX WRENCH 3MM
313 P0814313 FLAT WASHER 5/16 341 P0814341 PUSH BLOCK
314 P0814314 CARRI AGE BOLT 5/16-18 X 5/8 350V2 P0814350V2 WHEEL (BLACK) V2.03.19
315 P0814315 HEX BOLT 3/8-16 X 3/4 360AV2 P0814360AV2 FOOT PEDAL ASSEMBLY V2.03. 19
316 P0814316 FLAT WASHER 3/8 361 P0814361 PEDAL
317 P0814317 MOTOR PULLEY 362 P0814362 PEDAL BRACKET
318 P0814318 SET SCREW 1/4-20 X 3/ 8 363 P0814363 TROLLEY BRACKET (UPPER)
319 P0814319 V-BELT A36 364 P0814364 TROLLEY BRACKET (LOWER)
320 P0814320 MOTOR 1HP 110V/220V 1-PH 365 P0814365 CLEVIS PIN, HEADLESS-GROOVED
320-1 P0814320-1 MOTOR FAN COV ER 366 P0814366 FLAT WASHER 13 X 27 X 3MM
320-2 P0814320-2 MOTOR FAN 367 P0814367 E-CLIP 12MM
320-3 P0814320-3 CAPACI TOR COVER 368 P0814368 HEX BOLT 5/ 16-18 X 2
320-4 P0814320-4 MOTOR JUNCTI O N BO X 369 P0814369 FLAT WASHER 5/16
320-5 P0814320-5 S CAPACI TOR 300M 125V 1-3/4 X 3-3/8 370 P0814370 HEX BOLT 5/16-18 X 4
320-6 P0814320-6 BALL BEARING (FRONT) 371 P0814371 FLAT WASHER 5/16
320-7 P0814320-7 BALL BEARING (REAR) 372 P0814372 LOCK NUT 5/16-18 V1
320-8 P0814320-8 CONTACT PLA TE 372V2 P0814372V2 LOCK NUT 3/8-24 V2. 03.19
320-9 P0814320-9 CENTRI FUGA L S WI TCH 373V2 P0814373V2 WHEEL AXLE BOLT 3/8-24 X 2-1/ 2 V2.03. 19
320-10 P0814320-10 STRAIN RELIEF TYPE-2 M8-1.25 376 P0814376 HEX BOLT 3/8-16 X 2-1/2
321 P0814321 KEY 5 X 5 X 30 377 P0814377 FLAT WASHER 3/8
322 P0814322 PA DDLE SWI TCH KEDU HY-18 378 P0814378 HEX NUT 3/8-16
325 P0814325 POWER CORD 16G 3W 72" 5-15P 380 P0814380 LEVELING FOOT 3/18-16 X 2
326 P0814326 STRAIN RELI EF 5/8" TYPE-1 SNAP-I N SB6R-3 381 P0814381 FLAT WASHER 3/ 8
327 P0814327 FLANGE SCREW 10-24 X 3/8 382 P0814382 HEX NUT 3/8-16
328 P0814328 EXT TOOTH WASHER #10 383 P0814383 HEX BOLT 5/16-18 X 3/ 8
329 P0814329 HEX NUT 10-24 384V2 P0814384V2 WHEEL AXLE BOLT 3/8-24 X 2-1/ 2 V2.03. 19
331V2 P0814331V2 STAND V2.04.22 386V2 P0814386V2 LOCK NUT 3/8-24 V2. 03.19
332 P0814332 CABINET DOOR 390 P0814390 MOTOR CORD 16G 3W 31"
333V2 P0814333V2 FLANGE SCREW 8-32 X 3/8 V2. 04.22 393 P0814393 TAP SCREW #5 X 3/8
334 P0814334 DUST P ORT 4 "

Model G0814/G0814X (Mfd. Since 12/22)

BUY PARTS ONLI NE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

-63-

Labels & Cosmetics

401

G0814

REF PART # DESCRIPTION REF PART # DESCRIPTION

Specifications

Motor: 1 HP, 110V/220V, 1-Ph, 60 Hz
Full-Load Amp Draw: 14A
Cutterhead: 3-Knife, 2-1/2" Dia.
Knife Size: 6" x 1" x 1/8"
Maximum Depth of Cut: 1/8"
Maximum Rabbeting Depth: 1/2"
Cutterhead Speed: 5000 RPM
Cuts Per Minute: 15,000
Fence Tilt: 45º, 90º, 135º
Table Size: 47" x 7-1/4"
Weight: 245 lbs.

Date

S/N

Mfd. for Grizzly in Taiwan

Specifications

Motor: 1 HP, 110V/220V, 1-Ph, 60 Hz
Full-Load Current: 14A at 110V, 7A at 220V
Cutterhead: V-Helical w/Indexable Inserts
Insert Size: 15 x 15 x 2.5mm
Number of Inserts: 24
Replacement Inserts: T32014
Number of Insert Rows: 4
Maximum Depth of Cut: 1/8"
Maximum Rabbeting Depth: 1/2"
Cutterhead Speed: 5000 RPM
Cuts Per Minute: 20,000
Fence Tilt: 45º, 90º, 135º
Table Size: 47-3/8" x 6-5/8"
Weight: 245 lbs.

Date

S/N

Mfd. for Grizzly in Taiwan

403

WARNING!

INJURY HAZARD!

To reduce risk of short
and long-term injury,
wear safety glasses,
hearing protection, and
a respirator when using
this machine.

MODEL G0814

6

"

JOINTER w/CABINET STAND

To reduce the risk of serious injury when using this machine:

1. Read & understand owner’s manual before operating.

2. Always wear approved eye protection and respirator.

3. Only plug power cord into a grounded outlet.

4. Except when rabbeting, keep all guards in place and in proper

5. Never cut workpieces smaller than 8" long, 3/4" wide, or 1/2" thick.

6. Always use push blocks when face planing.

7. Never cut deeper than 1/8" on a single pass.

8. Tie back long hair, roll up sleeves, and DO NOT wear loose

9. Turn motor OFF and disconnect power before changing inserts,

10. Before starting, ensure tables are adjusted properly, blades are

11. Always support workpiece against fence and table. Never attempt

12. Always feed workpiece against cutterhead rotation. Never move

13. Prevent unauthorized use by children or untrained users; restrict

WARNING!

operating condition. Always replace guard after rabbeting.

clothing, gloves, or jewelry.

adjusting tables/fence, or servicing.

secure, and jointer is stable.

any operation free-handed.

workpiece backward while feeding.

access or disable machine when unattended.

410

MODEL G0814X

6

"

JOINTER w/STAND &

V-HELICAL CUTTERHEAD

To reduce the risk of serious injury when using this machine:

1. Read & understand owner’s manual before operating.

2. Always wear approved eye protection and respirator.

3. Only plug power cord into a grounded outlet.

4. Except when rabbeting, keep all guards in place and in proper

5. Never cut workpieces smaller than 8" long, 3/4" wide, or 1/2" thick.

6. Always use push blocks when face planing.

7. Never cut deeper than 1/8" on a single pass.

8. Tie back long hair, roll up sleeves, and DO NOT wear loose

9. Turn motor OFF and disconnect power before changing inserts,

10. Before starting, ensure tables are adjusted properly, inserts are

11. Always support workpiece against fence and table. Never attempt

12. Always feed workpiece against cutterhead rotation. Never move

13. Prevent unauthorized use by children or untrained users; restrict

WARNING!

operating condition. Always replace guard after rabbeting.

clothing, gloves, or jewelry.

adjusting tables/fence, or servicing.

secure, and jointer is stable.

any operation free-handed.

workpiece backward while feeding.

access or disable machine when unattended.

412

WARNING!

To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call [phone] or
go to www.grizzly.com.

Failure to keep hands clear
of cutterhead will result in
serious personal injury.

Cutterhead

exposed between

these lines.

411

INJURY/SHOCK

HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.

408

407

Failure to keep hands clear
of cutterhead will result in
serious personal injury.

404

409

ROTATING CUTTERHEAD BELOW!

Use this guard for all operations
possible, and immediately re-install it
following operations that require its
removal.

KICKBACK HAZARD!

1. Ensure outfeed table is even with
knives.

2. Never exceed maximum depth of cut.

3. Do not stand directly behind workpiece.

ALWAYS USE PUSH BLOCKS!

Push blocks minimize possibility of

operator’s hands contacting cutterhead

while cutting.

402

405

G0814X

406

404

401 P0814401 CUTTERHEAD EXPOSURE WARNI NG LABEL 407 P0814407 GRIZZLY. COM LABEL
402 P0814402 CUTTERHEAD WARNI NG L ABEL 408 P0814408 TOUCH-UP PAI NT, GRI ZZLY G REE N
403 P0814403 EYE/EAR/LUNG WARNING LABEL 409 P0814409 TOUCH-UP PA I NT, GRIZZLY BEI GE
404 P0814404 ELECTRICITY LABEL 410 P0814410 MACHI NE ID LABEL (G0814)
405 P0814405 MODEL NUMBER LABEL (G0814) 410 P0814X410 MACHINE ID LABEL (G0814X)
405 P0814X405 MODEL NUMBER LABEL (G0814X) 411 P0814411 DISCONNECT POWER LABEL
406 P0814406 GRIZZLY NAMEPLATE-SMALL 412 P0814412 READ MANUAL LABEL

Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
before resuming operations. For replacements, contact [phone] or www.grizzly.com.

-64-

BUY PARTS ONLI NE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

Model G0814/G0814X (Mfd. Since 12/22)

WARRANTY & RETURNS

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from
the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,

negligence,accidents,repairsoralterationsorlackofmaintenance.ThisisGrizzly’ssolewrittenwarranty

and any and all warranties that may be implied by law, including any merchantability or fitness, for any par­ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent
that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.

InnoeventshallGrizzly’sliabilityunderthiswarrantyexceedthepurchasepricepaidfortheproductand

any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.

We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,
or consequential damages arising from the use of our products.

The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.

In the event you need to use this warranty, contact us by mail or phone and give us all the details. We will

thenissueyoua “ReturnNumber,’’whichmustbe clearlypostedontheoutside aswellastheinside of

the carton. We will not accept any item back without this number. Proof of purchase must accompany the
merchandise.

Please feel free to write or call us if you have any questions about the machine or the manual.

Thank you again for your business and continued support. We hope to serve you again soon.

For further information about the

scan the QR

code below

to be automatically directed to our warranty page.

warranty, visit https://www.grizzly.com/forms/warranty or

WARRANTY