Grizzly G0783 Owner's Manual

MODEL G0783

11" SLOW SPEED

COLD CUT SAW

OWNER'S MANUAL

(For models manufactured since 05/15)

COPYRIGHT © JANUARY, 2016 BY GRIZZLY INDUSTRIAL, INC.

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#JH17567 PRINTED IN CHINA

V1. 0 5 .16

This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.

Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.

The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and compre­hension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.

The manufacturer will not be held liable for injury or property damage
from negligence, improper training, machine modifications or misuse.

Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State
of California to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks, cement and other masonry products.

• Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equip­ment, such as those dust masks that are specially designed to filter
out microscopic particles.

Table of Contents

INTRODUCTION ............................................... 2

Contact Info.................................................... 2

Manual Accuracy ........................................... 2

Identification ................................................... 3

Controls & Components ................................. 4

SECTION 1: SAFETY ....................................... 7

Safety Instructions for Machinery .................. 7

Safety Instructions for Metal Cutting Saws .... 9

SECTION 2: POWER SUPPLY ...................... 10

SECTION 3: SETUP ....................................... 12

Unpacking .................................................... 12

Needed for Setup ......................................... 12

Inventory ...................................................... 12

Cleanup ........................................................ 13

Site Considerations ...................................... 14

Lifting & Placing ........................................... 14

Anchoring to Floor ....................................... 15

Assembly ..................................................... 15

Test Run ...................................................... 17

SECTION 4: OPERATIONS ........................... 18

Operation Overview ..................................... 18

Adjusting Vise .............................................. 19

Adjusting Miter Angle ................................... 20

Changing Blade ........................................... 20

Adding/Changing Coolant ............................ 22

Blade Terminology ....................................... 23

Blade Pitch ................................................... 23

Blade Feed Rate .......................................... 25

Blade Speed Selection ................................ 25

Blade Break-in ............................................. 25

Adjusting Miter Lock Lever .......................... 26

General Machine Tips .................................. 26

SECTION 5: ACCESSORIES ......................... 27

SECTION 6: MAINTENANCE ......................... 29

Schedule ...................................................... 29

Cleaning & Protecting .................................. 29

Lubrication ................................................... 29

SECTION 7: SERVICE ................................... 32

Troubleshooting ........................................... 32

SECTION 8: WIRING ...................................... 34

Wiring Safety Instructions ............................ 34

Wiring Overview ........................................... 35

Wiring Diagram ............................................ 36

SECTION 9: PARTS ....................................... 37

Base ............................................................. 37

Vise .............................................................. 38

Motor ............................................................ 39

Column & Headstock ................................... 40

Electrical Parts ............................................. 41

Labels & Cosmetics ..................................... 42

WARRANTY AND RETURNS ........................ 43

INTRODUCTION

We stand behind our machines! If you have ques­tions or need help, contact us with the information
below. Before contacting, make sure you get the

serial number

machine ID label. This will help us help you faster.

We want your feedback on this manual. What did
you like about it? Where could it be improved?
Please take a few minutes to give us feedback.

Email: [e-mail]

We are proud to provide a high-quality owner’s
manual with your new machine!

We

instruc­tions, specifications, drawings, and photographs
in this manual. Sometimes we make mistakes, but
our policy of continuous improvement also means
that

you receive is

slightly different than shown in the manual

If you find this to be the case, and the difference
between the manual and machine leaves you
confused or unsure about something

check our

website for an updated version. W

current

manuals and

on our web-

site at

Alternatively, you can call our Technical Support
for help. Before calling, make sure you write down
the

from
the machine ID label (see below). This information
is required for us to provide proper tech support,
and it helps us determine if updated documenta­tion is available for your machine.

Contact Info

and manufacture date from the

Grizzly Technical Support

1815 W. Battlefield
Springfield, MO 65807
Phone: [phone]

Email: [e-mail]

Grizzly Documentation Manager

P.O. Box 2069

Bellingham, WA 98227-2069

Manual Accuracy

made every effort to be exact with the

sometimes the machine

.

,

e post

manual updates for free

www.grizzly.com.

Manufacture Date and Serial Number

Manufacture Date

Serial Number

-2-

G0783 (Mfd. Since 05/15)

Identification

To reduce your risk of
serious injury, read this
entire manual BEFORE

Trigger

Button

Vise

Handwheel

Miter
Lock

Lever

Vise

Splash

Guard

Lever

Arm

Blade

Guard

Blade Speed Switch

Emergency Stop Button

Master

Power Switch

Oil Level Sight Glass

Coolant Hose

Depth Stop

Miter Angle Gauge

G0783 (Mfd. Since 05/15)

Cabinet

using machine.

-3-

Controls &

To reduce your risk of
serious injury, read this
entire manual BEFORE

G. Trigger Button: Turns motor ON, rotating

blade and activating cutting fluid pump.

Components

using machine.

Refer to Figures 1–3 and the following descrip­tions to become familiar with the basic controls
and components of this machine. Understanding
these items and how they work will help you
understand the rest of the manual and stay safe
when operating this machine.

A

B

H. Vise Handwheel: Opens and closes self-cen-

tering vise jaws to clamp workpiece.

E

F

J

Figure 2. Saw controls.

I. Miter Lock Lever: Releases or locks rotation

of saw base for angled cuts.

J. Vise Jaws: Independently adjustable vise

jaws with beveled edges for saw blade
clearance.

G

H

I

C

D

Figure 1. Control box and headstock.

A. Blade Speed Switch: Selects blade speed

of "1" (57 RPM) or "2" (114 RPM).

B. Emergency Stop Button: Cuts power to

motor and remains depressed until reset.
Twist clockwise to reset.

C. Master Power Switch: Supplies power to

machine for operation.

D. Depth Stop: Stops blade at specific depth to

produce multiple same-depth cuts.

E. Cutting Fluid Valve: Enables flow of cutting

fluid from reservoir to nozzle.

K

L

Figure 3. Cutting fluid reservoir and coolant

pump.

K. Coolant Pump: Supplies cutting fluid from

fluid reservoir to blade.

L. Cutting Fluid Reservoir: Holds cutting

fluid and can be removed for disposal and
cleaning.

F. Lever Arm: Houses trigger button and low-

ers saw blade into workpiece.

-4-

G0783 (Mfd. Since 05/15)

Machine

Data Sheet

MODEL G0783 11" SLOW SPEED COLD CUT SAW

Product Dimensions:

Weight ........................................................................................................................................................................... 386 lbs.

Width (side-to-side) x Depth (front-to-back) x Height .................................................................................18

Foot Print (Length/Width) ..................................................................................................................................... 20

Shipping Dimensions:

Type ........................................................................................................................................................................ Wood Crate

Content .......................................................................................................................................................................... Machine

Weight ............................................................................................................................................................................ 441 lbs.

Length/Width/Height ...........................................................................................................................................37 x 22 x 58 in.

Electrical:

Power Requirement ................................................................................................................................ 220V, 3-Phase, 60 Hz

Prewired Voltage ................................................................................................................................................................ 220V

Full-Load Current Rating ...................................................................................................................................................... 10A

Minimum Circuit Size .............................................................................................................................................15A @ 220V

Connection Type ................................................................................................................................................. Cord And Plug

Power Cord Included ............................................................................................................................................................Yes

Power Cord Length ............................................................................................................................................................7

Power Cord Gauge .......................................................................................................................................................14 AWG

Plug Included .........................................................................................................................................................................No

Recommended Plug Type ...............................................................................................................................................L15-15

Switch Type ..........................................................................................................................Power, Start, E-Stop, Dual Speed

1

⁄2 x 35 x 551⁄2 in.

1

⁄2 x 181⁄2 in.

1

⁄2 ft.

Motor:

Main

Coolant Pump

Type ..........................................................................................................................................................TEFC Induction

Horsepower ................................................................................................................................................2.7 HP/1.9 HP

Voltage ..................................................................................................................................................................... 220V

Phase .................................................................................................................................................................. 3-Phase

Amps .................................................................................................................................................................9.1A/6.3A

Number Of Speeds ..........................................................................................................................................................2

Speed ......................................................................................................................................................3300/1650 RPM

Cycle ........................................................................................................................................................................ 60 Hz

Power Transfer ................................................................................................................................................ Gear Drive

Bearings ......................................................................................................................Sealed & Permanently Lubricated

Type ................................................................................................................................ TEFC Capacitor-Start Induction

Horsepower ........................................................................................................................................................ 40 Watts

Voltage ..................................................................................................................................................................... 220V

Phase .......................................................................................................................................................... Single-Phase

Amps ......................................................................................................................................................................... 0.9A

Speed ...............................................................................................................................................................2760 RPM

Cycle ........................................................................................................................................................................ 60 Hz

Number Of Speeds ..........................................................................................................................................................1

Bearings ...................................................................................................................Shielded & Permanently Lubricated

G0783 (Mfd. Since 05/15)

-5-

Main Specifications:

Operation Information

Blade Speed ..................................................................................................................................................114/57 RPM

Blade Size ................................................................................................................................................ 11 in. (275mm)

Arbor Size ................................................................................................................................................................40mm

Cutting Operation

Angle Cuts .................................................................................................................................................... 45 – 90 deg.

Vise Jaw Depth .......................................................................................................................................................4

Vise Jaw Height ..........................................................................................................................................................2 in.

Maximum Capacity Square @ 90° ................................................................................................................. 2

Maximum Capacity Rectangular @ 90° ......................................................................................................... 2

Maximum Capacity Round @ 90° ........................................................................................................................... 2

Maximum Capacity Square @ 45° ................................................................................................................. 2

Maximum Capacity Rectangular @ 45° ......................................................................................................... 2

Maximum Capacity Round @ 45° ........................................................................................................................... 2

Construction

Table Construction ................................................................................................................................................Casting

Saw Wheel Cover ......................................................................................................................................................Steel

Saw Wheel Guard .....................................................................................................................................................Steel

Body Construction .................................................................................................................................................Casting

Paint ......................................................................................................................................................................Enamel

Other Specifications:

Country of Origin ............................................................................................................................................................... China

Warranty ........................................................................................................................................................................... 1 Year

Approximate Assembly & Setup Time .............................................................................................................................1 Hour

Serial Number Location ..................................................................................................................................Machine ID Label

1

⁄2 in.

3

⁄8 x 23⁄8 in.

3

⁄4 x 23⁄8 in.

3

⁄8 in.

3

⁄8 x 23⁄8 in.

3

⁄8 x 23⁄8 in.

3

⁄8 in.

Features:

2.7 HP, 2-speed motor
Gear-driven blade for low-RPM cutting
Cooling pump keeps blade from overheating
Dual-speed cutting ability

-6-

G0783 (Mfd. Since 05/15)

SECTION 1: SAFETY

For Your Own Safety, Read Instruction

Manual Before Operating This Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions.
This manual uses a series of symbols and signal words intended to convey the level of impor­tance of the safety messages. The progression of symbols is described below. Remember that
safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures. Always use common sense and good judgment.

Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.

This symbol is used to alert the user to useful information about

NOTICE

proper operation of the machine.

Safety Instructions for Machinery

OWNER’S MANUAL. Read and understand this

owner’s manual BEFORE using machine.

TRAINED OPERATORS ONLY. Untrained oper­ators have a higher risk of being hurt or killed.
Only allow trained/supervised people to use this
machine. When machine is not being used, dis­connect power, remove switch keys, or lock-out
machine to prevent unauthorized use—especially
around children. Make workshop kid proof!

DANGEROUS ENVIRONMENTS. Do not use
machinery in areas that are wet, cluttered, or have
poor lighting. Operating machinery in these areas
greatly increases the risk of accidents and injury.

MENTAL ALERTNESS REQUIRED. Full mental
alertness is required for safe operation of machin­ery. Never operate under the influence of drugs or
alcohol, when tired, or when distracted.

ELECTRICAL EQUIPMENT INJURY RISKS. You
can be shocked, burned, or killed by touching live
electrical components or improperly grounded
machinery. To reduce this risk, only allow qualified
service personnel to do electrical installation or
repair work, and always disconnect power before
accessing or exposing electrical equipment.

DISCONNECT POWER FIRST.
nect machine from power supply BEFORE making
adjustments, changing tooling, or servicing machine.
This prevents an injury risk from unintended startup
or contact with live electrical components.

EYE PROTECTION. Always wear ANSI-approved
safety glasses or a face shield when operating or
observing machinery to reduce the risk of eye
injury or blindness from flying particles. Everyday
eyeglasses are NOT approved safety glasses.

Always discon-

G0783 (Mfd. Since 05/15)

-7-

WEARING PROPER APPAREL. Do not wear
clothing, apparel or jewelry that can become
entangled in moving parts. Always tie back or
cover long hair. Wear non-slip footwear to reduce
risk of slipping and losing control or accidentally
contacting cutting tool or moving parts.

HAZARDOUS DUST. Dust created by machinery
operations may cause cancer, birth defects, or
long-term respiratory damage. Be aware of dust
hazards associated with each workpiece mate­rial. Always wear a NIOSH-approved respirator to
reduce your risk.

HEARING PROTECTION. Always wear hear­ing protection when operating or observing loud
machinery. Extended exposure to this noise
without hearing protection can cause permanent
hearing loss.

REMOVE ADJUSTING TOOLS. Tools left on
machinery can become dangerous projectiles
upon startup. Never leave chuck keys, wrenches,
or any other tools on machine. Always verify
removal before starting!

USE CORRECT TOOL FOR THE JOB. Only use
this tool for its intended purpose—do not force
it or an attachment to do a job for which it was
not designed. Never make unapproved modifica­tions—modifying tool or using it differently than
intended may result in malfunction or mechanical
failure that can lead to personal injury or death!

AWKWARD POSITIONS. Keep proper footing
and balance at all times when operating machine.
Do not overreach! Avoid awkward hand positions
that make workpiece control difficult or increase
the risk of accidental injury.

CHILDREN & BYSTANDERS. Keep children and
bystanders at a safe distance from the work area.
Stop using machine if they become a distraction.

GUARDS & COVERS. Guards and covers reduce
accidental contact with moving parts or flying
debris. Make sure they are properly installed,
undamaged, and working correctly BEFORE
operating machine.

FORCING MACHINERY. Do not force machine.
It will do the job safer and better at the rate for
which it was designed.

NEVER STAND ON MACHINE. Serious injury
may occur if machine is tipped or if the cutting
tool is unintentionally contacted.

STABLE MACHINE. Unexpected movement dur­ing operation greatly increases risk of injury or
loss of control. Before starting, verify machine is
stable and mobile base (if used) is locked.

USE RECOMMENDED ACCESSORIES. Consult
this owner’s manual or the manufacturer for rec­ommended accessories. Using improper acces­sories will increase the risk of serious injury.

UNATTENDED OPERATION. To reduce the
risk of accidental injury, turn machine OFF and
ensure all moving parts completely stop before
walking away. Never leave machine running
while unattended.

MAINTAIN WITH CARE. Follow all maintenance
instructions and lubrication schedules to keep
machine in good working condition. A machine
that is improperly maintained could malfunction,
leading to serious personal injury or death.

DAMAGED PARTS. Regularly inspect machine
for damaged, loose, or mis-adjusted parts—or
any condition that could affect safe operation.
Immediately repair/replace BEFORE operating
machine. For your own safety, DO NOT operate
machine with damaged parts!

MAINTAIN POWER CORDS. When disconnect­ing cord-connected machines from power, grab
and pull the plug—NOT the cord. Pulling the cord
may damage the wires inside. Do not handle
cord/plug with wet hands. Avoid cord damage by
keeping it away from heated surfaces, high traffic
areas, harsh chemicals, and wet/damp locations.

EXPERIENCING DIFFICULTIES. If at any time
you experience difficulties performing the intend­ed operation, stop using the machine! Contact our
Technical Support at [phone].

-8-

G0783 (Mfd. Since 05/15)

Serious injury or death can occur from getting fingers, hair, or clothing entangled in rotating or
moving parts. Workpieces can be ejected by saw, striking operator or bystanders. Long-term
respiratory damage can occur from breathing metal dust created while cutting. To minimize risk
of injury, anyone operating this machine MUST completely heed hazards and warnings below.

FIRE HAZARD. Use EXTREME CAUTION if cut-

ting magnesium. Using the wrong cutting fluid will
lead to chip fire and possible explosion.

CUTTING FLUID SAFETY. Always follow manu­facturer’s cutting-fluid safety instructions. Pay
particular attention to contact, contamination,
inhalation, storage and disposal warnings. Spilled
cutting fluid invites slipping hazards.

ATTENTION TO WORK AREA. Never leave a
machine running and unattended. Pay attention
to the actions of others in the area to avoid unin­tended accidents.

MAINTENANCE/SERVICE. All inspections,
adjustments, and maintenance are to be done
with the power OFF and the plug pulled from the
outlet. Wait for all moving parts to come to a com­plete stop.

HEARING PROTECTION & HAZARDS. Noise
generated by blade and workpiece vibration,
material handling, and power transmission can
cause permanent hearing loss over time and
interfere with communication and audible signals.

HOT SURFACES. Contact with hot surfaces from
machine components, ejections of hot chips,
swarf, and the workpiece itself can cause burns.

BLADE CONDITION. Do not operate with dull,
cracked or badly worn blade. Inspect blades for
cracks and missing teeth before each use.

HAND PLACEMENT. Never position fingers or
thumbs in line with the cut. Hands could be
crushed in vise or from falling machine compo­nents.

ENTANGLEMENT HAZARDS. Do not operate
this saw without blade guard in place. Loose
clothing, jewelry, long hair and work gloves can be
drawn into working parts.

BLADE REPLACEMENT. When replacing
blades, disconnect the machine from power, wear
gloves to protect hands and safety glasses to
protect eyes.

WORKPIECE HANDLING. Always support the
workpiece with table, vise, or some type of sup­port fixture. Flag long pieces to avoid a tripping
hazard. Never hold the workpiece with your hands
during a cut.

LOSS OF STABILITY. Unsupported workpieces
may jeopardize machine stability and cause the
machine to tip and fall which could cause serious
injury.

POWER INTERRUPTION. Unplug machine after
power interruption. Machines without magnetic
switches can start up after power is restored.

Additional Safety for Metal Cutting Saws

No list of safety guidelines can be complete. Every shop environment is different. Like all
machines there is danger associated with the Model G0783. Accidents are frequently caused by
lack of familiarity or failure to pay attention. Use this machine with respect and caution to lessen
the possibility of operator injury. If normal safety precautions are overlooked or ignored, serious
personal injury may occur.

G0783 (Mfd. Since 05/15)

-9-

SECTION 2: POWER SUPPLY

Before installing the machine, consider the avail­ability and proximity of the required power supply
circuit. If an existing circuit does not meet the
requirements for this machine, a new circuit must
be installed. To minimize the risk of electrocution,
fire, or equipment damage, installation work and
electrical wiring must be done by an electrician or
qualified service personnel in accordance with all
applicable codes and standards.

Electrocution, fire, or
equipment damage may
occur if machine is not
correctly grounded and
connected to the power

The full-load current rating is the amperage a
machine draws at 100% of the rated output power.
On machines with multiple motors, this is the
amperage drawn by the largest motor or sum of all
motors and electrical devices that might operate
at one time during normal operations.

The full-load current is not the maximum amount
of amps that the machine will draw. If the machine
is overloaded, it will draw additional amps beyond
the full-load rating.

If the machine is overloaded for a sufficient length
of time, damage, overheating, or fire may result—
especially if connected to an undersized circuit.
To reduce the risk of these hazards, avoid over­loading the machine during operation and make
sure it is connected to a power supply circuit that
meets the specified circuit requirements.

For your own safety and protection of

Note: Circuit requirements in this manual apply to

a dedicated circuit—where only one machine will
be running on the circuit at a time. If machine will
be connected to a shared circuit where multiple
machines may be running at the same time, con­sult an electrician or qualified service personnel to
ensure circuit is properly sized for safe operation.

A power supply circuit includes all electrical
equipment between the breaker box or fuse panel
in the building and the machine. The power sup­ply circuit used for this machine must be sized to
safely handle the full-load current drawn from the
machine for an extended period of time. (If this
machine is connected to a circuit protected by
fuses, use a time delay fuse marked D.)

This machine is prewired to operate on a power
supply circuit that has a verified ground and meets
the following requirements:

Availability

supply.

Full-Load Current Rating

Circuit Information

property, consult an electrician if you are
unsure about wiring practices or electrical
codes in your area.

Full-Load Current Rating at 220V ..... 10 Amps

-10 -

Circuit Requirements

Nominal Voltage .........208V, 220V, 230V, 240V

Cycle .......................................................... 60 Hz

Phase .................................................... 3-Phase

Power Supply Circuit ......................... 15 Amps

Plug/Receptacle ....................................... 15-15

G0783 (Mfd. Since 05/15)

Improper connection of the equipment-grounding
wire can result in a risk of electric shock. The
wire with green insulation (with or without yellow
stripes) is the equipment-grounding wire. If repair
or replacement of the power cord or plug is nec­essary, do not connect the equipment-grounding
wire to a live (current carrying) terminal.

Check with a qualified electrician or service per­sonnel if you do not understand these grounding
requirements, or if you are in doubt about whether
the tool is properly grounded. If you ever notice
that a cord or plug is damaged or worn, discon­nect it from power, and immediately replace it with
a new one.

We do not recommend using an extension cord
with this machine.
cord, only use it if absolutely necessary and only
on a temporary basis.

Extension cords cause voltage drop, which can
damage electrical components and shorten motor
life. Voltage drop increases as the extension cord
size gets longer and the gauge size gets smaller
(higher gauge numbers indicate smaller sizes).

Any extension cord used with this machine must
be in good condition and contain a ground wire
and matching plug/receptacle. Additionally, it must
meet the following size requirements:

No adapter should be used with plug. If

Grounding Instructions

This machine MUST be grounded. In the event
of certain malfunctions or breakdowns, grounding
reduces the risk of electric shock by providing a
path of least resistance for electric current.

The plug specified under “Circuit Requirements”
on the previous page has a grounding prong that
must be attached to the equipment-grounding
wire on the included power cord. The plug must
only be inserted into a matching receptacle (see
following figure) that is properly installed and
grounded in accordance with all local codes and
ordinances.

GROUNDED

15-15 RECEPTACLE

15-15 PLUG

Serious injury could occur if you connect
machine to power before completing setup
process. DO NOT connect to power until
instructed later in this manual.

Current

Carrying

Grounding Prong

Prongs

Figure 4. Typical 15-15 plug and receptacle.

plug does not fit available receptacle, or if
machine must be reconnected for use on a
different type of circuit, reconnection must
be performed by an electrician or qualified
service personnel, and it must comply with
all local codes and ordinances.

G0783 (Mfd. Since 05/15)

Extension Cords

If you must use an extension

Minimum Gauge Size ...........................14 AWG

Maximum Length (Shorter is Better).......50 ft.

-11-

SECTION 3: SETUP

This machine was carefully packaged for safe
transport. When unpacking, separate all enclosed
items from packaging materials and inspect them
for shipping damage.

,

please

IMPORTANT:

you are completely satisfied with the machine and
have resolved any issues between Grizzly or the
shipping agent. You MUST have the original pack-

aging to file a freight claim. It is also extremely
helpful if you need to return your machine later.

Keep children and pets away
from plastic bags or packing
materials shipped with this

The following is a list of items shipped with your
machine. Before beginning setup, lay these items
out and inventory them.

If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.

Unpacking

If items are damaged

call us immediately at [phone].

Save all packaging materials until

SUFFOCATION HAZARD!

Inventory

Small Item Inventory (Figure 5) Qty

A. Lever Arm w/Hex Nut M22-2.5 ................... 1

B. Eye Bolts 28mm, M12-1.75 x 22 ................. 4

C. Miter Lock Lever Cap ................................. 1

D. Vise Handwheel Handles ........................... 4

E. Flat Washer 22mm ..................................... 1

A

B

C

machine. Discard immediately.

Needed for Setup

The following items are needed, but not included,
for the setup/assembly of this machine.

Description Qty

• Additional People ....................................... 2

• Safety Glasses (Per Person) ...................... 1

• Cleaner/Degreaser (Page 13) .... As Needed

• Disposable Shop Rags ............... As Needed

• Lifting Straps (Rated Min. 500 lbs.) ............ 2

• Screwdriver Flat Head #2 ........................... 1

• Open-End Wrench

• Open-End Wrench 12mm ........................... 1

-12-

7

⁄8" ................................ 1

D

E

Figure 5. G0783 inventory.

NOTICE

If you cannot find an item on this list, care­fully check around/inside the machine and
packaging materials. Often, these items get
lost in packaging materials while unpack­ing or they are pre-installed at the factory.

G0783 (Mfd. Since 05/15)

The unpainted surfaces of your machine are
coated with a heavy-duty rust preventative that
prevents corrosion during shipment and storage.
This rust preventative works extremely well, but it
will take a little time to clean.

Be patient and do a thorough job cleaning your
machine. The time you spend doing this now will
give you a better appreciation for the proper care
of your machine's unpainted surfaces.

There are many ways to remove this rust preven­tative, but the following steps work well in a wide
variety of situations. Always follow the manufac­turer’s instructions with any cleaning product you
use and make sure you work in a well-ventilated
area to minimize exposure to toxic fumes.

Before cleaning, gather the following:

• Disposable rags

• Cleaner/degreaser (WD•40 works well)

• Safety glasses & disposable gloves

• Plastic paint scraper (optional)

Basic steps for removing rust preventative:

1.

2.

3.

4.

Many cleaning solvents

work in a well-ventilated

Avoid chlorine-based solvents, such as

Cleanup

Gasoline and petroleum
products have low flash
points and can explode
or cause fire if used to
clean machinery. Av o i d
using these products
to clean machinery.

Put on safety glasses.

Coat the rust preventative with a liberal

amount of cleaner/degreaser, then let it soak
for 5–10 minutes.

Wipe off the surfaces. If your cleaner/degreas-

er is effective, the rust preventative will wipe
off easily. If you have a plastic paint scraper,
scrape off as much as you can first, then wipe
off the rest with the rag.

Repeat Steps 2–3 as necessary until clean,

then coat all unpainted surfaces with a quality
metal protectant to prevent rust.

are toxic if inhaled. Only

area.

NOTICE

acetone or brake parts cleaner, that may
damage painted surfaces.

T23692—Orange Power Degreaser

A great product for removing the waxy ship­ping grease from the non-painted parts of the
machine during clean up.

Figure 6. T23692 Orange Power Degreaser.

G0783 (Mfd. Since 05/15)

-13-