Grizzly G0762 Owner's Manual

MODEL G0762

HEAVY-DUTY VARIABLE-SPEED

MILL/DRILL w/POWER FEED

OWNER'S MANUAL

(For models manufactured since 5/14)

COPYRIGHT © JUNE, 2014 BY GRIZZLY INDUSTRIAL, INC.

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#TSDM16171 PRINTED IN CHINA

V1. 0 6 .14

This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.

Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.

The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and compre­hension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.

The manufacturer will not be held liable for injury or property damage
from negligence, improper training, machine modifications or misuse.

Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State
of California to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks, cement and other masonry products.

• Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equip­ment, such as those dust masks that are specially designed to filter
out microscopic particles.

Table of Contents

INTRODUCTION ............................................... 2

Machine Description ...................................... 2

Contact Info.................................................... 2

Manual Accuracy ........................................... 2

Identification ................................................... 3

Controls & Components ................................. 4

Machine Data Sheet ...................................... 6

SECTION 1: SAFETY ....................................... 8

Safety Instructions for Machinery .................. 8

Additional Safety for Mill/Drills ..................... 10

SECTION 2: POWER SUPPLY ...................... 11

Availability .................................................................11

Full-Load Current Rating ...........................................11

Circuit Information .....................................................11

Circuit Requirements .................................................11

Grounding Requirements ..........................................12

Extension Cords ........................................................12

SECTION 3: SETUP ....................................... 13

Unpacking .................................................... 13

Needed for Setup ......................................... 13

Inventory ...................................................... 14

Cleanup ........................................................ 15

Site Considerations ...................................... 16

Lifting & Placing ........................................... 17

Bench Mounting ........................................... 17

Assembly ..................................................... 18

Joining Drill Chuck & Arbor .......................... 19

Lubricating Mill/Drill ...................................... 19

Test Run ...................................................... 20

Spindle Bearing Break-In ............................. 22

Inspections & Adjustments .......................... 22

SECTION 4: OPERATIONS ........................... 23

Operation Overview ..................................... 23

Spindle Movement ....................................... 24

Using Coarse Downfeed ...........................................24

Using Fine Downfeed ................................................24

Depth Stop ................................................... 24

Headstock Movement .................................. 25

Raising/Lowering Headstock .....................................25

Tilting Headstock .......................................................25

Table Travel ................................................. 26

Graduated Dials ........................................................26

X-Axis Handwheel .....................................................26

Y-Axis Handwheel .....................................................26

X-Axis Power Feed ...................................................27

Installing/Removing Tooling ......................... 27

Installing Tooling .......................................................28

Removing Tooling .....................................................28

Spindle Speed.............................................. 29

Determining Spindle Speed ......................................29

Setting Spindle Speed ...............................................29

SECTION 5: ACCESSORIES ......................... 30

SECTION 6: MAINTENANCE ......................... 31

Schedule ...................................................... 31

Cleaning and Protecting .............................. 31

Lubrication ................................................... 31

Headstock .................................................................32

Ball Oilers ..................................................................33

Table & Column Ways ..............................................33

Quill Outside Surface ................................................34

Table Leadscrews .....................................................34

Z-Axis Leadscrew & Pinion Gear ..............................35

Quill Rack & Pinion ...................................................35

SECTION 7: SERVICE ................................... 36

Troubleshooting ........................................... 36

Adjusting Gibs .............................................. 38

Adjusting Leadscrew Backlash .................... 38

Tightening Return Spring Tension ............... 39

SECTION 8: WIRING ...................................... 40

Wiring Safety Instructions ............................ 40

Wiring Overview ........................................... 41

Electrical Cabinet Wiring .............................. 42

Control Panel & Motor Wiring ...................... 44

SECTION 8: PARTS ....................................... 46

Headstock Diagram ..................................... 46

Table & Column Diagram ............................ 49

Electrical Component Diagram .................... 51

Included Accessories ................................... 53

Labels & Cosmetics ..................................... 54

WARRANTY & RETURNS ............................. 57

INTRODUCTION

We are proud to provide a high-quality owner’s
manual with your new machine!

We

instruc­tions, specifications, drawings, and photographs
contained inside. Sometimes we make mistakes,
but

also

means that

you receive
will be slightly different than what is shown in
the manual

If you find this to be the case, and the difference
between the manual and machine leaves you
confused about a procedure
for an updated version. W

manuals

and

www.grizzly.com

Alternatively, you can call our Technical Support
for help. Before calling, please write down the

Manufacture Date

stamped
into the machine ID label (see below). This infor­mation helps us determine if updated documenta­tion is available for your machine.

We stand behind our machines. If you have
any questions or need help, use the information
below to contact us. Before contacting, please get
the serial number and manufacture date of your
machine. This will help us help you faster.

We want your feedback on this manual. What did
you like about it? Where could it be improved?
Please take a few minutes to give us feedback.

Machine Description

This mill/drill is used to shape metal workpieces
by removing material with the use of a rotating
cutting tool.

In milling operations, the cutting tool rotates in
place while the workpiece moves under it with the
table.

In drilling operations, the workpiece is held sta­tionary on the table while the rotating cutting tool
moves up-and-down with the movement of the
spindle.

The spindle is reversible and features both coarse
and fine downfeed controls. The variable spindle
speeds of 75–2500 RPM are controlled by an
electronic variable-speed dial and one gearbox
lever, with the current spindle speed displayed on
the digital readout.

Contact Info

Manual Accuracy

made every effort to be exact with the

our policy of continuous improvement

sometimes the machine

.

, check our website

e post current

manual updates for free on our website at

.

and Serial Number

Grizzly Technical Support

1203 Lycoming Mall Circle

Muncy, PA 17756

Phone: [phone]

Email: [e-mail]

Grizzly Documentation Manager

P.O. Box 2069

Bellingham, WA 98227-2069

Email: [e-mail]

Manufacture Date

Serial Number

-2-

Model G0762 (Mfd. Since 5/14)

Identification

To reduce your risk of
serious injury, read this
entire manual BEFORE

Become familiar with the names and locations of the controls and features shown below to better understand
the instructions in this manual.

Drawbar

Cap

Gearbox

Lever

Motor

Dovetail

Column

Z-Axis

Lock

Control

Depth Stop

& Scale

X-Axis

Power Feed

Power Feed

Stop

Handwheel

Panel

Fine Downfeed

Handwheel

Quill Lock

Y-Axis

Spindle

X-Axis

Table Locks

Headstock

Tilt Scale

Electrical

Cabinet

Downfeed

Selector Knob

Coarse

Downfeed Handle

Power Feed

Stop

Table

X-Axis

Handwheel

Y-Axis

Table Lock

Model G0762 (Mfd. Since 5/14)

using machine.

-3-

Controls &

To reduce your risk of
serious injury, read this
entire manual BEFORE

Components

using machine.

Refer to Figures 1–5 and the following descrip­tions to become familiar with the basic controls of
this machine.

A

H

B

G

C

E. EMERGENCY STOP Button: Cuts power

to the spindle motor and remains depressed
until reset. Twist clockwise until it pops out to
reset.

F. STOP Button: Stops spindle rotation.

G. POWER Button: When pushed, enables

power to the control panel and illuminates.

H. SPINDLE FORWARD Button: Starts clock-

wise spindle rotation (as viewed from above).
The spindle must be completely stopped
before this button is pushed.

I. Master Power Switch: Enables power to the

machine.

I

F

E

Figure 1. Control panel and spindle speed

controls.

A. RPM Digital Readout: Displays spindle

speed.

B. Variable-Speed Dial: Controls spindle speed

within the selected range.

C. High/Low Range Lever: Selects either high

or low spindle speed range.

D. SPINDLE REVERSE Button: Starts coun-

terclockwise spindle rotation (as viewed from
above). The spindle must be completely
stopped before this button is pushed.

D

J

Figure 2. Location of master power switch and

Z-axis crank.

J. Z-Axis Crank: Moves headstock up and

down.

-4-

Model G0762 (Mfd. Since 5/14)

R

K

L

P

O

M

N

Figure 3. Downfeed controls.

K. Fine Downfeed Handwheel: Moves spindle

up and down in small increments. One revo­lution equals 0.10" of spindle travel.

L. Downfeed Selector Knob: Selects fine or

coarse downfeed controls. When loosened,
coarse downfeed is engaged; when tight­ened, fine downfeed is engaged.

M. Coarse Downfeed Handle: Moves spindle

up and down rapidly.

Q

S

V

U

T

Figure 4. X-axis power feed controls.

Q. ON/OFF Light: Illuminates when the unit is

turned ON.

R. Directional Lever: Controls the direction of

table travel.

S. Rapid Switch: Moves the table rapidly in the

direction chosen when held down.

T. Power Light: Illuminates when the unit is

connected to power.

U. Speed Dial: Controls the rate of feed.

N. Depth Stop Adjustment Knob: Adjusts

depth stop.

O. Quill Lock Lever: When milling, locks quill in

place for greater rigidity for more precision.

P. Depth Stop and Scale: Shows the position

of the spindle and can limit spindle travel.

V. ON/OFF Switch: Turns the power feed ON

and OFF.

W. Limit Stops: Work with limit switch to restrict

X-axis table movement.

X. Limit Switch: Stops table movement when

either side plunger contacts a limit stop.

W

X

Figure 5. Limit switch and limit stops.

Model G0762 (Mfd. Since 5/14)

-5-

Machine Data Sheet

MACHINE DATA

SHEET

Customer Service #: [phone] · To Order Call: [phone] · Fax #: [phone]

MODEL G0762 HEAVY-DUTY BENCHTOP MILL/DRILL WITH

VARIABLE-SPEED AND POWER FEED

Product Dimensions:

Weight.............................................................................................................................................................. 728 lbs.

Width (side-to-side) x Depth (front-to-back) x Height............................................................... 49-5/8 x 36-5/8 x 61 in.

Footprint (Length x Width)............................................................................................................... 21-5/8 x 17-3/4 in.

Shipping Dimensions:

Type.......................................................................................................................................................... Wood Crate

Content........................................................................................................................................................... Machine

Weight.............................................................................................................................................................. 732 lbs.

Length x Width x Height....................................................................................................................... 35 x 36 x 46 in.

Electrical:

Power Requirement............................................................................................................ 220V, Single-Phase, 60Hz

Full-Load Current Rating....................................................................................................................................... 6.2A

Minimum Circuit Size.............................................................................................................................................. 15A

Power Cord Included.............................................................................................................................................. Yes

Power Cord Length................................................................................................................................................. 5 ft.

Power Cord Gauge......................................................................................................................................... 14 AWG

Plug Included........................................................................................................................................................... No

Recommended Plug Type..................................................................................................................................... 6-15

Switch Type........................................................................................... Control Panel w/ Magnetic Switch Protection

Motors:

Main

Type........................................................................................................................................... TEFC Induction

Horsepower................................................................................................................................................ 2 HP

Phase.................................................................................................................................................... 3-Phase

Amps........................................................................................................................................................... 6.2A

Speed................................................................................................................................................ 2300 RPM

Power Transfer ................................................................................................................................. Gear Drive

Bearings..................................................................................................... Shielded & Permanently Lubricated

Main Specifications:

Operation Info

Spindle Travel........................................................................................................................................ 4-3/4 in.

Max Distance Spindle to Column........................................................................................................ 10-1/8 in.

Max Distance Spindle to Table............................................................................................................ 18-1/8 in.

Longitudinal Table Travel (X-Axis)............................................................................................................. 22 in.

Cross Table Travel (Y-Axis).................................................................................................................. 7-1/2 in.

Vertical Head Travel (Z-Axis).............................................................................................................. 13-3/4 in.

Head Tilt (Left/Right)........................................................................................................ Right 45, Left 45 deg.

Drilling Capacity for Cast Iron................................................................................................................ 1-1/4 in.

Drilling Capacity for Steel............................................................................................................................ 1 in.

End Milling Capacity.................................................................................................................................... 1 in.

Face Milling Capacity................................................................................................................................... 3 in.

-6-

Model G0762 (Mfd. Since 5/14)

Table Info

Table Length........................................................................................................................................ 31-1/2 in.

Table Width........................................................................................................................................... 9-1/2 in.

Table Thickness.................................................................................................................................... 2-1/2 in.

Number of T-Slots............................................................................................................................................ 3

T-Slot Size................................................................................................................................................ 1/2 in.

T-Slots Centers...................................................................................................................................... 3-1/8 in.

Spindle Info

Spindle Taper............................................................................................................................................... R-8

Number of Vertical Spindle Speeds...................................................................................................... Variable

Range of Vertical Spindle Speeds............................................................................................. 75 – 2500 RPM

Quill Diameter.............................................................................................................................................. 3 in.

Drawbar Thread Size............................................................................................................................. 7/16-20

Drawbar Length................................................................................................................................... 17-3/4 in.

Spindle Bearings......................................................................... High-Precision "P5" Tapered Roller Bearings

Construction

Spindle Housing/Quill........................................................................................................................... Cast Iron

Table.................................................................................................................................................... Cast Iron

Head.................................................................................................................................................... Cast Iron

Column/Base....................................................................................................................................... Cast Iron

Stand.......................................................................................................................................................... Steel

Paint Type/Finish.................................................................................................................................... Enamel

Other Specifications:

Country of Origin ................................................................................................................................................ China

Warranty ........................................................................................................................................................... 1 Year

Approximate Assembly & Setup Time .............................................................................................................. 1 Hour

Serial Number Location .................................................................................................................................. ID Label

Sound Rating ................................................................................................................................................... <80 dB

ISO 9001 Factory .................................................................................................................................................. Yes

CSA, ETL, or UL Certified/Listed ............................................................................................................................ No

Features:

Inverter speed control
Dovetail ways
High-precision P5 tapered-roller spindle bearings
Coolant trough built into table
High efficiency motor fan
Digital spindle speed display

Accessories Included:

Drill chuck 1-13mm with B16 taper
Tool box

Model G0762 (Mfd. Since 5/14)

-7-

SECTION 1: SAFETY

For Your Own Safety, Read Instruction

Manual Before Operating This Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions.
This manual uses a series of symbols and signal words intended to convey the level of impor­tance of the safety messages. The progression of symbols is described below. Remember that
safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures. Always use common sense and good judgment.

Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.

This symbol is used to alert the user to useful information about

NOTICE

proper operation of the machine.

Safety Instructions for Machinery

OWNER’S MANUAL. Read and understand this

owner’s manual BEFORE using machine.

TRAINED OPERATORS ONLY. Untrained oper­ators have a higher risk of being hurt or killed.
Only allow trained/supervised people to use this
machine. When machine is not being used, dis­connect power, remove switch keys, or lock-out
machine to prevent unauthorized use—especially
around children. Make workshop kid proof!

DANGEROUS ENVIRONMENTS. Do not use
machinery in areas that are wet, cluttered, or have
poor lighting. Operating machinery in these areas
greatly increases the risk of accidents and injury.

MENTAL ALERTNESS REQUIRED. Full mental
alertness is required for safe operation of machin­ery. Never operate under the influence of drugs or
alcohol, when tired, or when distracted.

ELECTRICAL EQUIPMENT INJURY RISKS. You
can be shocked, burned, or killed by touching live
electrical components or improperly grounded
machinery. To reduce this risk, only allow qualified
service personnel to do electrical installation or
repair work, and always disconnect power before
accessing or exposing electrical equipment.

DISCONNECT POWER FIRST.
nect machine from power supply BEFORE making
adjustments, changing tooling, or servicing machine.
This prevents an injury risk from unintended startup
or contact with live electrical components.

EYE PROTECTION. Always wear ANSI-approved
safety glasses or a face shield when operating or
observing machinery to reduce the risk of eye
injury or blindness from flying particles. Everyday
eyeglasses are NOT approved safety glasses.

Always discon-

-8-

Model G0762 (Mfd. Since 5/14)

WEARING PROPER APPAREL. Do not wear
clothing, apparel or jewelry that can become
entangled in moving parts. Always tie back or
cover long hair. Wear non-slip footwear to avoid
accidental slips, which could cause loss of work­piece control.

HAZARDOUS DUST. Dust created while using
machinery may cause cancer, birth defects, or
long-term respiratory damage. Be aware of dust
hazards associated with each workpiece material,
and always wear a NIOSH-approved respirator to
reduce your risk.

HEARING PROTECTION. Always wear hear­ing protection when operating or observing loud
machinery. Extended exposure to this noise
without hearing protection can cause permanent
hearing loss.

REMOVE ADJUSTING TOOLS. Tools left on
machinery can become dangerous projectiles
upon startup. Never leave chuck keys, wrenches,
or any other tools on machine. Always verify
removal before starting!

USE CORRECT TOOL FOR THE JOB. Only use
this tool for its intended purpose—do not force
it or an attachment to do a job for which it was
not designed. Never make unapproved modifica­tions—modifying tool or using it differently than
intended may result in malfunction or mechanical
failure that can lead to personal injury or death!

AWKWARD POSITIONS. Keep proper footing
and balance at all times when operating machine.
Do not overreach! Avoid awkward hand positions
that make workpiece control difficult or increase
the risk of accidental injury.

CHILDREN & BYSTANDERS. Keep children and
bystanders at a safe distance from the work area.
Stop using machine if they become a distraction.

FORCING MACHINERY. Do not force machine.
It will do the job safer and better at the rate for
which it was designed.

NEVER STAND ON MACHINE. Serious injury
may occur if machine is tipped or if the cutting
tool is unintentionally contacted.

STABLE MACHINE. Unexpected movement dur­ing operation greatly increases risk of injury or
loss of control. Before starting, verify machine is
stable and mobile base (if used) is locked.

USE RECOMMENDED ACCESSORIES. Consult
this owner’s manual or the manufacturer for rec­ommended accessories. Using improper acces­sories will increase the risk of serious injury.

UNATTENDED OPERATION. To reduce the
risk of accidental injury, turn machine OFF and
ensure all moving parts completely stop before
walking away. Never leave machine running
while unattended.

MAINTAIN WITH CARE. Follow all maintenance
instructions and lubrication schedules to keep
machine in good working condition. A machine
that is improperly maintained could malfunction,
leading to serious personal injury or death.

CHECK DAMAGED PARTS. Regularly inspect
machine for any condition that may affect safe
operation. Immediately repair or replace damaged
or mis-adjusted parts before operating machine.

MAINTAIN POWER CORDS. When disconnect­ing cord-connected machines from power, grab
and pull the plug—NOT the cord. Pulling the cord
may damage the wires inside. Do not handle
cord/plug with wet hands. Avoid cord damage by
keeping it away from heated surfaces, high traffic
areas, harsh chemicals, and wet/damp locations.

GUARDS & COVERS. Guards and covers reduce
accidental contact with moving parts or flying
debris. Make sure they are properly installed,
undamaged, and working correctly.

Model G0762 (Mfd. Since 5/14)

EXPERIENCING DIFFICULTIES. If at any time
you experience difficulties performing the intend­ed operation, stop using the machine! Contact our
Technical Support at [phone].

-9-

Additional Safety for Mill/Drills

The primary risks of operating a Mill/Drill are as follows: You can be seriously injured or killed by
getting clothing, jewelry, or long hair entangled with rotating cutter. You can be severely cut or
have your fingers amputated from contact with the rotating cutter. You can be blinded or struck
with great force by broken cutting tools, metal chips, workpieces, or adjustment tools thrown
from the rotating spindle. To reduce your risk of serious injury when operating this machine,
completely heed and understand the following:

UNDERSTAND ALL CONTROLS. Make sure

you understand the function and proper use of all
controls before starting. This will help you avoid
making mistakes that result in serious injury.

WEAR FACE SHIELD. Always wear a face shield
in addition to safety glasses. This provides more
complete protection for your face than safety
glasses alone.

REMOVE CHUCK KEY & SPINDLE TOOLS.
Always remove chuck key, drawbar wrench, and
other tools used on the spindle immediately after
use. This will prevent them from being thrown by
the spindle upon startup.

PROPERLY SECURE CUTTER. Firmly secure
cutting tool or drill bit so it does not fly out of spin­dle during operation.

USE CORRECT SPINDLE SPEED. Follow rec­ommended speeds and feeds for each size and
type of cutting tool. This helps avoid tool breakage
during operation and ensures best cutting results.

INSPECT CUTTING TOOL. Inspect cutting tools
for sharpness, chips, or cracks before each use.
Replace dull, chipped, or cracked cutting tools
immediately.

ALLOW SPINDLE TO STOP. To minimize your
risk of entanglement, always allow spindle to stop
on its own. DO NOT stop spindle using your hand
or any other object.

SECURE WORKPIECE TO TABLE. Clamp work­piece to table or secure in a vise mounted to table,
so workpiece cannot unexpectedly shift or spin
during operation. NEVER hold workpiece by hand
during operation.

CLEAN MACHINE SAFELY. Metal chips or shav­ings can be razor sharp. DO NOT clear chips
by hand or compressed air that can force chips
farther into machine—use a brush or vacuum
instead. Never clear chips while spindle is turning.

PROPERLY MAINTAIN MACHINE. Keep machine
in proper working condition to help ensure that it
functions safely and all guards and other compo­nents work as intended. Perform routine inspec­tions and all necessary maintenance. Never oper­ate machine with damaged or worn parts that can
break or result in unexpected movement during
operation.

DISCONNECT POWER FIRST. To reduce risk of
electrocution or injury from unexpected startup,
make sure mill/drill is turned OFF, disconnected
from power, and all moving parts have come to
a complete stop before changing cutting tools or
starting any inspection, adjustment, or mainte­nance procedure.

POWER DISRUPTION. In the event of a local
power outage during operation, turn spindle switch
OFF to avoid a possible sudden startup once
power is restored.

-10 -

Model G0762 (Mfd. Since 5/14)

SECTION 2: POWER SUPPLY

Before installing the machine, consider the avail­ability and proximity of the required power supply
circuit. If an existing circuit does not meet the
requirements for this machine, a new circuit must
be installed. To minimize the risk of electrocution,
fire, or equipment damage, installation work and
electrical wiring must be done by an electrican or
qualified service personnel in accordance with all
applicable codes and standards.

Electrocution, fire, or
equipment damage may
occur if machine is not
correctly grounded and
connected to the power

The full-load current rating is the amperage a
machine draws at 100% of the rated output power.
On machines with multiple motors, this is the
amperage drawn by the largest motor or sum of all
motors and electrical devices that might operate
at one time during normal operations.

The full-load current is not the maximum amount
of amps that the machine will draw. If the machine
is overloaded, it will draw additional amps beyond
the full-load rating.

If the machine is overloaded for a sufficient length
of time, damage, overheating, or fire may result—
especially if connected to an undersized circuit.
To reduce the risk of these hazards, avoid over­loading the machine during operation and make
sure it is connected to a power supply circuit that
meets the requirements in the following section.

For your own safety and protection of

Note: The circuit requirements listed in this man­ual apply to a dedicated circuit—where only one
machine will be running at a time. If this machine
will be connected to a shared circuit where mul­tiple machines will be running at the same time,
consult a qualified electrician to ensure that the
circuit is properly sized for safe operation.

A power supply circuit includes all electrical
equipment between the breaker box or fuse panel
in the building and the machine. The power sup­ply circuit used for this machine must be sized to
safely handle the full-load current drawn from the
machine for an extended period of time. (If this
machine is connected to a circuit protected by
fuses, use a time delay fuse marked D.)

This machine is prewired to operate on a power
supply circuit that has a verified ground and meets
the following requirements:

Availability

supply.

Full-Load Current Rating

Circuit Information

property, consult an electrician if you are
unsure about wiring practices or electrical
codes in your area.

Full-Load Current Rating at 220V .... 6.2 Amps

Model G0762 (Mfd. Since 5/14)

Circuit Requirements

Nominal Voltage ................... 220V, 230V, 240V

Cycle ..........................................................60 Hz

Phase .................................................... 1-Phase

Power Supply Circuit ......................... 15 Amps

Plug/Receptacle ............................. NEMA 6-15

-11-

Improper connection of the equipment-grounding
wire can result in a risk of electric shock. The
wire with green insulation (with or without yellow
stripes) is the equipment-grounding wire. If repair
or replacement of the power cord or plug is nec­essary, do not connect the equipment-grounding
wire to a live (current carrying) terminal.

Check with a qualified electrician or service per­sonnel if you do not understand these grounding
requirements, or if you are in doubt about whether
the tool is properly grounded. If you ever notice
that a cord or plug is damaged or worn, discon­nect it from power, and immediately replace it with
a new one.

We do not recommend using an extension cord
with this machine.
cord, only use it if absolutely necessary and only
on a temporary basis.

Extension cords cause voltage drop, which may
damage electrical components and shorten motor
life. Voltage drop increases as the extension cord
size gets longer and the gauge size gets smaller
(higher gauge numbers indicate smaller sizes).

Any extension cord used with this machine must
contain a ground wire, match the required plug
and receptacle, and meet the following require­ments:

Grounding Requirements

This machine MUST be grounded. In the event
of certain malfunctions or breakdowns, grounding
reduces the risk of electric shock by providing a
path of least resistance for electric current.

This machine is equipped with a power cord
that has an equipment-grounding wire and a
grounding plug. The plug must only be inserted
into a matching receptacle (outlet) that is prop­erly installed and grounded in accordance with all
local codes and ordinances.

No adapter should be used with the
required plug. If the plug does not fit the
available receptacle, or the machine must

GROUNDED

6-15 RECEPTACLE

Current Carrying Prongs

6-15 PLUG

Serious injury could occur if you connect
the machine to power before completing the
setup process. DO NOT connect to power
until instructed later in this manual.

Grounding Prong

Figure 6. Typical 6-15 plug and receptacle.

be reconnected for use on a different type
of circuit, the reconnection must be made
by a qualified electrician and comply with all
local codes and ordinances.

-12-

Extension Cords

If you must use an extension

Minimum Gauge Size ...........................14 AWG

Maximum Length (Shorter is Better).......50 ft.

Model G0762 (Mfd. Since 5/14)

SECTION 3: SETUP

Your machine was carefully packaged for safe
transportation. Remove the packaging materials
from around your machine and inspect it. If you
discover any damage, please call us immediately

at [phone]

Save the containers and all packing materials for
possible inspection by the carrier or its agent.

Otherwise, filing a freight claim can be difficult.

When you are completely satisfied with the condi
tion of your shipment, inventory the contents.

Keep children and pets away
from plastic bags or packing
materials shipped with this

Unpacking

for advice.

SUFFOCATION HAZARD!

Needed for Setup

The following are needed to complete the setup
process, but are not included with your machine.

Description Qty

• Additional People ....................................... 1

• Safety Glasses ........................ 1 Per Person

• Cleaner/Degreaser (Page 15) .... As Needed

• Disposable Shop Rags ............... As Needed

• Forklift ......................................................... 1

• Lifting Sling (rated for at least 1000 lbs.) .... 1

-

• Mounting Hardware (Page 17) ... As Needed

• Flat Head Screwdriver #2 ........................... 1

• Mineral Spirits (Page 19) ............ As Needed

• Block of Wood (Page 19) ........................... 1

machine. Discard immediately.

Model G0762 (Mfd. Since 5/14)

-13-

Inventory

The following is a list of items shipped with your
machine. Before beginning setup, lay these items
out and inventory them.

If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.

A

C

B

D

NOTICE

If you cannot find an item on this list, care­fully check around/inside the machine and
packaging materials. Often, these items get
lost in packaging materials while unpack­ing or they are pre-installed at the factory.

Small Item Inventory (Figures 7–8) Qty

A. Handwheel Handles w/Screws ................... 2

B. T-Bolts M12-1.75 x 55 w/Washers & Nuts . . 2

C. Bottle for Oil ............................................... 1

D. Toolbox ....................................................... 1

E. Wrenches 17/19, 22/24mm ....................1 Ea

F. Hex Wrenches 2.5, 3, 4, 5, 10mm .........1 Ea

G. Drift Key ...................................................... 1

H. Drill Chuck w/Chuck Key B16, 1–13mm ..... 1

I. Spindle Sleeve R-8 x MT#3 ....................... 1

J. Drill Chuck Arbor R-8 x B16 ....................... 1

K. Spindle Sleeve MT#3 x MT#2 .................... 1

L. Handwheels ................................................ 2

M. Compression Spring (X-Axis Handwheel) . . 1
N. Cap Screws M8-1.25 x 12 (Handwheels) ... 2

O. Handwheel Flat Washers 8mm .................. 2

P. Power Feed Assembly (Not Shown) ........... 1

Q. Cap Screws M8-1.25 x 20

(Not Shown; Power Feed) .......................... 2

K

J

H

Figure 7. Small item inventory.

Figure 8. Small item inventory.

I

G

L

E

F

M

N

O

-14-

Model G0762 (Mfd. Since 5/14)

The unpainted surfaces of your machine are
coated with a heavy-duty rust preventative that
prevents corrosion during shipment and storage.
This rust preventative works extremely well, but it
will take a little time to clean.

Be patient and do a thorough job cleaning your
machine. The time you spend doing this now will
give you a better appreciation for the proper care
of your machine's unpainted surfaces.

There are many ways to remove this rust preven­tative, but the following steps work well in a wide
variety of situations. Always follow the manufac­turer’s instructions with any cleaning product you
use and make sure you work in a well-ventilated
area to minimize exposure to toxic fumes.

Before cleaning, gather the following:

• Disposable rags

• Cleaner/degreaser (WD•40 works well)

• Safety glasses & disposable gloves

• Plastic paint scraper (optional)

Basic steps for removing rust preventative:

1.

2.

3.

4.

Many cleaning solvents

work in a well-ventilated

Avoid chlorine-based solvents, such as

Cleanup

Gasoline and petroleum
products have low flash
points and can explode
or cause fire if used to
clean machinery. Avoid
using these products
to clean machinery.

Put on safety glasses.

Coat the rust preventative with a liberal

amount of cleaner/degreaser, then let it soak
for 5–10 minutes.

Wipe off the surfaces. If your cleaner/degreas-

er is effective, the rust preventative will wipe
off easily. If you have a plastic paint scraper,
scrape off as much as you can first, then wipe
off the rest with the rag.

are toxic if inhaled. Only

area.

NOTICE

acetone or brake parts cleaner, that may
damage painted surfaces.

T23692—Orange Power Degreaser

A great product for removing the waxy shipping
grease from your machine during clean up.

Figure 9. T23692 Orange Power Degreaser.

Repeat Steps 2–3 as necessary until clean,

then coat all unpainted surfaces with a quality
metal protectant to prevent rust.

Model G0762 (Mfd. Since 5/14)

-15-

Site Considerations

Weight Load

Physical Environment

Place this machine near an existing power source.

Shadows, glare, or strobe effects that may distract

Refer to the Machine Data Sheet for the weight
of your machine. Make sure that the surface upon
which the machine is placed will bear the weight
of the machine, additional equipment that may be
installed on the machine, and the heaviest work­piece that will be used. Additionally, consider the
weight of the operator and any dynamic loading
that may occur when operating the machine.

Space Allocation

Consider the largest size of workpiece that will
be processed through this machine and provide
enough space around the machine for adequate
operator material handling or the installation of
auxiliary equipment. With permanent installations,
leave enough space around the machine to open
or remove doors/covers as required by the main­tenance and service described in this manual.

See below for required space allocation.

Children or untrained people
may be seriously injured by
this machine. Only install in an
access restricted location.

The physical environment where the machine is
operated is important for safe operation and lon­gevity of machine components. For best results,
operate this machine in a dry environment that is
free from excessive moisture, hazardous chemi­cals, airborne abrasives, or extreme conditions.
Extreme conditions for this type of machinery are
generally those where the ambient temperature
range exceeds 41°–104°F; the relative humidity
range exceeds 20–95% (non-condensing); or the
environment is subject to vibration, shocks, or
bumps.

Electrical Installation

Make sure all power cords are protected from
traffic, material handling, moisture, chemicals,
or other hazards. Make sure to leave access to
a means of disconnecting the power source or
engaging a lockout/tagout device, if required.

Lighting

Lighting around the machine must be adequate
enough that operations can be performed safely.

or impede the operator must be eliminated.

Figure 10. Minimum working clearances.

-16 -

Wall

30"

Minimum Clearance

495⁄8"

621⁄2"

365⁄8"

Model G0762 (Mfd. Since 5/14)