TWO SPEED
FLOOR AIR FILTER
MODEL G0573
INSTRUCTION MANUAL
COPYRIGHT © DECEMBER, 2004 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#BL6811 PRINTED IN CHINA
WARNING
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains
chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement, and
other masonry products.
• Arsenic and chromium from chemically treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to fil
ter out microscopic particles.
-
Table of Contents
INTRODUCTION ............................................................................................................................... 2
Foreword .... 2
Contact Info
SECTION 1: SAFETY .......................................................................................................................
Safety Instructions for
SECTION 2: CIRCUIT REQUIREMENTS ........................................................................................
110V Operation ..........................................................................................................................
SECTION 3: SET UP ........................................................................................................................
Set Up Safety .............................................................................................................................
Items Needed For Set Up .......................................................................................................... 7
Unpacking .. 7
SECTION 4: OPERATIONS ...........................................................................................................
Operation Safety ......................................................................................................................
Operations 10
Available Accessories .............................................................................................................. 10
SECTION 5: MAINTENANCE ........................................................................................................
G0573 Wire Diagram ...............................................................................................................
G0573 Parts Breakdown .......................................................................................................... 13
WARRANTY AND RETURNS ........................................................................................................
Machinery ............................................................................................... 3
10
10
11
12
16
2
3
6
6
7
7
INTRODUCTION
Foreword
We are proud to offer the Model G0573 Two Speed
Floor Air Filter. This machine is part of a growing
Grizzly family of fine woodworking machinery.
When used according to the guidelines set forth in
this manual, you can expect years of trouble-free,
enjoyable operation and proof of Grizzly’s com
mitment to customer satisfaction.
We are pleased to provide this manual with the
Model G0573. It was written to guide you through
assembly, review safety considerations, and cover
general operating procedures.
The specifications, drawings, and photographs
illustrated in this manual represent the Model
G0573 as supplied when the manual was prepared. For your convenience, we always keep
current Grizzly manuals available on our website
at www.grizzly.com. Any updates to your machine
will be reflected in these manuals as soon as they
are complete.
Contact Info
If you have any comments regarding this manual,
please write to us at the address below:
Grizzly Industrial, Inc.
C
/O Technical Documentation
Bellingham, WA 98227-2069
We stand behind our machines. If you have any
service questions or parts requests, please call or
write us at the location listed below.
E-Mail: techsupport@grizzly.com
Web Site: http://www.grizzly.com
P.O. Box 2069
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
-2-
MACHINE DATA
SHEET
Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901
MODEL G0573 TWO SPEED FLOOR AIR FILTER
Motor ..............1 3⁄4 HP, 2-Speed, 110 Volt, 1 PH
Amp Draw .............HI = 14 Amps, LO = 12 Amps
Dimensions ............30 1/2"L x 25 3/4" W x 29 3/8"H
Pre-Filter Dimensions ........... 25"L x 25"H x
Primary Filter Dimensions
Weight .....................................................165 lbs.
Airflow .................................... 1500 to 2000 CFM
Pre-Filter Filtration .............................. 3 Microns
Primary Filter Filtration .. .3 Microns (2000 CFM)
24"L x 24"H x 113/4"D
7
/8"D
G0573 Two Speed Floor Air Filter
SECTION 1: SAFETY
For Your Own Safety, Read Instruction
Manual Before Operating this Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions. This
manual uses a series of symbols and signal words which are intended to convey the level of
importance of the safety messages. The progression of symbols is described below. Remember
that safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.
NOTICE
This symbol is used to alert the user to useful information about
proper operation of the machine.
Safety Instructions for Machinery
1. READ THROUGH THE ENTIRE MANUAL
BEFORE STARTING MACHINERY.
Machinery presents serious injury hazards
to untrained users.
2. ALWAYS USE ANSI APPROVED
SAFETY GLASSES WHEN OPERATING
MACHINERY. Everyday eyeglasses only
have impact resistant lenses, they are
NOT safety glasses.
4. ALWAYS USE HEARING PROTECTION
WHEN
Machinery noise can cause permanent
hearing damage.
5. WEAR PROPER APPAREL. DO NOT
wear loose clothing, gloves, neckties, rings,
or jewelry which may get caught in moving
parts. Wear protective hair covering to con
tain long hair and wear non-slip footwear.
OPERATING MACHINERY.
-
3. ALWAYS WEAR AN ANSI APPROVED
RESPIRATOR WHEN OPERATING
MACHINERY THAT PRODUCES DUST.
Wood dust is
cancer and severe respiratory illnesses.
G0573 Two Speed Floor Air Filter
a carcinogen and can cause
6. NEVER OPERATE MACHINERY WHEN
TIRED, OR UNDER THE INFLUENCE OF
DRUGS OR ALCOHOL. Be mentally alert
at all times when running machinery.
-3-
Safety Instructions for Machinery
7. ONLY ALLOW TRAINED AND PROPERLY SUPERVISED PERSONNEL TO
OPERATE MACHINERY. Make sure
operation instructions are safe and clearly
understood.
8. KEEP CHILDREN AND VISITORS AWAY.
Keep all children and visitors a safe distance from the work area.
9. MAKE WORKSHOP CHILD PROOF. Use
padlocks, master switches, and remove
start switch keys.
10. NEVER LEAVE WHEN MACHINE IS
RUNNING. Turn power OFF and allow all
moving parts to come to a complete stop
before leaving machine unattended.
11. DO NOT USE IN DANGEROUS
ENVIRONMENTS. DO NOT use machin-
ery in damp, wet locations, or where any
flammable or noxious fumes may exist.
12. KEEP WORK AREA CLEAN AND WELL
LIT. Clutter and dark shadows may cause
accidents.
13. USE A GROUNDED EXTENSION CORD
RATED FOR MACHINE AMPERAGE.
Undersized cords overheat and lose power.
Replace extension cords if they become
damaged. DO NOT use extension cords
for 220V machinery.
16. MAKE SURE GUARDS ARE IN PLACE
AND WORK CORRECTLY BEFORE
USING MACHINERY.
17. REMOVE ADJUSTING KEYS AND
WRENCHES. Make a habit of checking for
keys and adjusting wrenches before turn
ing machinery
18. CHECK FOR DAMAGED PARTS
BEFORE USING MACHINERY. Check
for binding and alignment of parts, broken
parts, part mounting, loose bolts, and any
other conditions that may affect machine
operation. Repair or replace damaged
parts.
19. USE RECOMMENDED ACCESSORIES.
Refer to the instruction manual for recom
mended accessories. The use of improper
accessories may cause risk of injury.
20. DO NOT FORCE MACHINERY. Work at
the speed for which the machine or acces
sory was designed.
21. SECURE WORKPIECE. Use clamps or
a vise to hold the workpiece when practical. A secured workpiece protects your
hands and frees both hands to operate the
machine.
22. DO NOT OVERREACH. Keep proper foot
ing and balance at all times.
ON.
-
-
-
-
14.
ALWAYS DISCONNECT FROM POWER
SOURCE BEFORE SERVICING
MACHINERY. Make sure switch is in
position before reconnecting.
15. MAINTAIN MACHINERY WITH CARE.
Keep blades sharp and clean for best and
safest performance. Follow instructions for
lubricating and changing accessories.
-4-
OFF
23. MANY MACHINES WILL EJECT
WORKPIECE TOWARD OPERATOR.
Know and avoid conditions that cause the
workpiece to "kickback."
24. ALWAYS LOCK MOBILE BASES
BEFORE OPERATING MACHINERY
G0573 Two Speed Floor Air Filter
.
Additional Safety for Air Filters
1. FILTER USE. This filter unit is only designed
to remove very fine wood particles from
the air. DO NOT use this machine to filter
or collect liquids (especially flammables),
metal shavings, lead paint, or asbestos. DO
NOT use this machine to dissipate smoke,
fumes, or when spraying paint.
2. FILTER REMOVAL. Unplug machine
before removing filter. Removing primary filter exposes the impeller, which may cause
serious injury during contact if the machine
is connected to the power source.
3. PROBLEMS WITH MOVING PARTS.
Problems concerned with moving parts or
accessories must be investigated and corrected with the power disconnected and
after the fan blade come to a complete
stop.
4. EXPLOSION RISK. Suspended dust par-
ticles in conjunction with an ignition source
may cause an explosion. Do not operate
this machine in areas where explosion risks
would be high if dust were dispersed into
the area. Areas of high risk include, but are
not limited to, areas near pilot lights or open
flames.
5. BURNING OR SMOKING MATERIAL
Avoid collecting any material that is burning
or smoking, including matches, cig
and hot ashes.
arettes,
6. MACHINE OPERATION. Always operate
the machine with the filter in place
the primary filter is removed, the impeller is
exposed to the unfiltered opening.
7. FILTER CLEANING AND REPLACEMENT.
Wear a respirator and safety glasses when
changing or replacing filters. Empty dust
into an approved container and dispose of
properly.
8. OPERATING DIFFICULTIES. If at any time
you are experiencing difficulties performing the intended operation
machine! Then contact our service department or ask a qualified expert how the
operation should be performed.
9. ALLERGIC REACTIONS. Be aware that
certain woods may cause an allergic reac
tion in people and animals, especially when
exposed to fine dust. Make sure you know
what type of wood dust you will be exposed
to in case there is a possibility of an allergic
reaction. Always wear an ANSI approved
respirator!
10.LEAD-PAINT DUST OR ASBESTOS
FIBERS. This machine will not protect
.
against lead-paint dust or asbestos fibers.
These materials must be collected with spe
cial equipment due to high hazard to human
health. DO NOT attempt to collect these
materials with this machine.
, stop using the
. When
-
-
Like all machines there is danger associated with the Model G0573. Accidents are
frequently caused by lack of familiarity or
failure to pay attention. Use this machine
with respect and caution to lessen the pos
sibility of operator injury. If normal safety
precautions are overlooked or ignored, seri
ous personal injury may occur.
G0573 Two Speed Floor Air Filter
No list of safety guidelines can be complete.
Every shop environment is different. Always
consider safety first, as it applies to your
individual working conditions. Use this and
-
-
other machinery with caution and respect.
Failure to do so could result in serious personal injury, damage to equipment, or poor
work results.
-5-
SECTION 2: CIRCUIT REQUIREMENTS
110V Operation
Electrocution or fire could
result if this machine is
not grounded correctly or
Serious personal injury could occur if you
connect the machine to the power source
before you have completed the set up pro
cess. DO NOT connect the machine to the
power source until instructed to do so.
-
Amperage Draw
The 1 3⁄4 HP motor on the Model G0573 will draw
the following amps:
Motor Load ....................................... 12-14 Amps
if your electrical configu
ration does not comply
with local and state codes.
Ensure compliance by
checking with a qualified
electrician!
-
Circuit Breaker Requirements
Install your machine on a dedicated circuit to
reduce the possibility of tripping the circuit break
er. If the circuit breaker frequently trips, have the
circuit inspected by a qualified electrician. Never
use a larger circuit breaker than stated below, or
you will increase the risk of fire.
Circuit Breaker .........................................
15 Amp
Plug Type
The Model G0573 is supplied with an invertedtype 5-15 plug. You must insert an extension cord
receptacle over the inverted plug and then insert
the male part of the extension cord into a 5-15
wall receptacle.
-
This machine must have a ground prong in
the plug to help ensure that it is grounded.
DO NOT remove ground prong from plug
to fit into a two-pronged outlet! If the plug
will not fit the outlet, have the proper outlet
installed by a qualified electrician.
Extension Cords
• Make sure the cord is rated Standard Service
(grade S) or better.
• The extension cord must contain a ground
wire and plug pin.
-6-
• Use at least a 16 gauge cord.
• DO NOT use a cord longer than 50 feet!
G0573 Two Speed Floor Air Filter
.
SECTION 3: SET UP
Set Up Safety
This machine presents
serious injury hazards
to untrained users. Read
through this entire manu
al to become familiar with
the controls and opera
tions before starting the
machine!
Wear safety glasses during the entire set up pro
cess!
The Model G0573 is a
heavy machine (165 lbs.
shipping weight) . DO
NOT over-exert yourself
while unpacking or mov
ing your machine—get
assistance.
Items Needed For
Set Up
The following items are needed to complete the
set up process, but are not included with your
machine:
-
-
-
-
DESCRIPTION QTY
• 16 guage extension cord (50 feet or less) . 1
• 12" diameter ducting (optional) ..................
Simply attach the female end of a 16 guage
extension cord onto the male 5-15 inverted plug
on the air filter, then plug the extension cord into
a grounded wall receptacle.
(Opitional)
you can attach 12" diameter metal ducting to the
exhaust vent.
Because of the high volume of air coming out
of the Model G0573, you may want to attach a
short length of ducting to control the direction of
this airflow in your shop.
To carry exhaust outside your shop,
1
Unpacking
G0573 Two Speed Floor Air Filter
The Model G0573 was carefully packed when it
left our warehouse. If you discover the machine
is damaged after you have signed for delivery,
please immediately call Customer Service at
(570) 546-9663
Save the containers and all packing materials for
possible inspection by the carrier or its agent.
Otherwise, filing a freight claim can be difficult.
When you are completely satisfied with the con
dition of your shipment, you should inventory the
contents.
for advice.
-7-
-
Shop Preparation
DO NOT operate this air
cleaner unit at a location
where flammable fuels,
solvents, or other vola
tile chemicals may exist.
Since these products
have a low flash point,
the fan motor can ignite
the fumes and cause an
explosion and severe
personal injury!
Unsupervised children and
visitors inside your shop
could cause serious personal
injury to themselves. Lock all
entrances to the shop when
you are away and DO NOT
allow unsupervised children
or visitors in your shop at
any time!
Operating Location
Operating this air cleaner unit in the incorrect
environment can cause an explosion or respira
tory damage to you and others. This air cleaner
unit is only designed to help remove very fine
wood particles from the air. It is not a dust
collector, so take all necessary safety pre
cautions.
of volatile fumes from fuels, paints, pesticides,
chemicals, smoke, and other gasses; including
an environment free of silica, metal, asbestos,
hazardous bacterium, and other particles.
The operating location must be free
-
Outlets
Make sure the electrical circuits have the capacity
to handle the amperage requirements of the new
air cleaner unit. Refer to Page
mation. Electrical outlets should be located near
the unit so power or extension cords are clear of
high-traffic areas.
6 for more infor-
Site Planning
Site planning is an important step to maximize
the effectiveness of the air filter. Air circulation
must be thought out and all obstructions to the
air path considered.
Think of air circulation in terms of the circular
motion of the air before and after the air filter.
The air exiting the filter is exhausted at a higher
velocity than that entering it. Consequently,
exhaust being vented inside a building can have
an effect on the pattern of air circulation.
The user may choose to vent exhaust horizon
tally from the 12" vent, install a short section of
metal ducting onto the vent to deflect exhaust
upward. Air circulation patterns will vary depend
ing upon which method is used, and according
to your specific shop setup.
-
-
Figure
tion
from the 12" exterior vent.
1 shows an example of good air circula-
where the user vents exhaust horizontally
-
-
Working Clearances
Make sure there is 5-10' of clearance between the
inlet and the outlet and any obstructions, as not
to restrict the air flow. You may have to create or
modify other shop ducting to achieve the correct
working clearances and airflow.
-8-
Filter
Figure 1. Good air circulation. The air filter
placement promotes circular air motion.
G0573 Two Speed Floor Air Filter
Figure 2 shows an example of poor air circulation,
where the air filter is placed too close to obstructions and the velocity of the air is lost and circulation is diminished.
Filter
Figure 2. Poor air circulation, filter is placed too
close to the wall.
Below is a list of things to keep in mind when
selecting a spot for the air filter:
• Study your shop layout and try to determine
the best location. Obstructed air flow will
cause a short cycle effect, producing unsat
isfactory results. There must be a clearance
of at least 5-10' between the front and back
of the unit and any obstructions.
• Try to place the air filter near areas where
sanding will take place.
• Try to place the unit where it is easy to
access for turning on, cleaning, and main
taining.
-
-
Filter Capacity
The G0573 Two Speed Floor Air Filter is designed
to recirculate the entire volume of air in a 30' x 40'
x 8' room approximately 12 times in one hour.
For the best filtering effect, the volume in a room
should be recirculated at least 6-8 times every
hour.
To calculate the recirculating rate for a given
volume:
Step 1. Calculate how long it takes to circulate
all the volume of air in a room with the air filter;
where W = Width, L = Length and H = Height of
your room, in feet. The highest rate of air move
ment for the air filter is 2000 cubic feet per min
ute.
W' x L' x H'
2000
Step 1:
Step 2. Calculate how many times per hour the
volume is recirculated through the air filter by
dividing 60 minutes by the amount of time it takes
to circulate the volume once. The result is listed
as times per hour.
Step 2: 60
= Minutes for one recirculation change
30' x 40' x 8'
2000
4.8
9600
=
2000
= 12.5 Times per Hour
= 4.8 Minutes
-
-
G0573 Two Speed Floor Air Filter
-9-
SECTION 4: OPERATIONS
OperationsOperation Safety
To operate the unit:
Operating this equipment creates the potential for flying debris to cause eye injury.
Always wear safety glasses when operating
equipment. Everyday glasses or reading
glasses only have impact resistant lenses,
they are not safety glasses. Be certain the
safety glasses you wear meet the appropriate standards of the American National
Standards Institute (ANSI).
Operations that generate
large amounts of any kind
of dust may warrant the
use of a respirator even
though the dust filter is
running. The dust filter
is not a substitute for a
respirator!
THIS DUST FILTER IS TO BE USED FOR
WOOD DUST ONLY
machine to filter toxic fumes or paint spray.
DO NOT use this machine to dissipate
smoke or fumes.
. DO NOT use this
1. Connect the unit to power and push the HI
or LOW start switch. The fan should start up
and begin filtering air in the room.
2. If it does not start, turn the switch OFF and
disconnect the power.
• Check the breaker/reset switch located next
to the start switch and reset if needed.
• Check to make sure the outlet connected to
the filter is in working condition. Reset the
breaker or replace the fuse if needed.
If the air filter continues to have problems, please
call our customer support lines at (570) 546-9663
for troubleshooting information.
Available Accessories
Grizzly carries a complete selection of fine
accessories for all of its equipment. Below is
a list of accessories we are sure you will find
useful.
• Dust Collection Basics, Model G2525
• Remote Dust Collector Switch, Model
H2797 or H5397
-10-
• Primary Filter, P0573007
• Pre-Filter, P0573008
G0573 Two Speed Floor Air Filter
SECTION 5: MAINTENANCE
!
Note—The pre-filter can be washed with
water to remove the last of the dust and help
To avoid personal injury,
disconnect power to air
filter when performing
any adjustments, clean
ing or maintenance.
-
maximize its filtering effect. DO NOT use
compressed air to clean the pre-filter, as it
may get damaged and lose its filtering capa
bilities.
4. Be sure the pre-filter is completely dry before
re-installing it into the air filter.
-
Use a respirator when
cleaning or changing fil
ters. Dust will become
airborne creating a respi
ratory hazard. For safety, run the air filter for
at least 6 minutes while
wearing the respirator
after cleaning.
-
-
Cleaning the Filters
To maintain optimal operation, the filters in the
Two Speed Floor Air Filter should be checked
and cleaned or replaced regularly depending
on usage. We recommend checking the primary
filter and pre-filter once a month or more often
if usage is high. Always wear a respirator when
checking the filters.
To check, clean or replace the filters:
The primary air filter is heavy and could
cause injuries if it drops on your feet. Use
care when sliding it out of the air filter
cabinet.
5. Slide the primary air filter out of the air filter
cabinet.
6. Slide a new primary air filter into the air filter
cabinet, shut the door and engage the latch
es.
During regular use, the pre-filter can be cleaned
several times before it needs to be replaced. It
is important to look for holes in the pre-filter that
would reduce the filtering effect. Please see the
current Grizzly catalog for replacement informa
tion.
-
-
1. Disconnect power to the air filter.
2. Disengage the latches and swing open the
front door.
3. Remove the pre-filter, place it inside a trash
bag, and gently shake the dust from the fil
ter.
G0573 Two Speed Floor Air Filter
-
-11-
G0573 Wire Diagram
-12-
G0573 Two Speed Floor Air Filter
40
41
38
37
36
35
1
2
3
4
5
6
7
8
9
10
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
34
33
39
G0573 Parts Breakdown
G0573 Two Speed Floor Air Filter
-13-
G0573 Parts List
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 P0573001 BODY 22 PS21M PHLP HD SCR M4-.7 X 15
2 P0573002 STEELY GRATE 23 PHTEK5M TAP SCREW M4.2 X 12
3 P0573003 ANGLE IRON 24 P0573024 FUSE
4 P0573004 FAN PLATE 25 P0573025 SWITCH BOX
5 P0573005 FAN HOUSING 26 P0573026 SWITCH PLATE
6 P0573006 FAN BLADE 27 P0573027 STRAIN RELIEF M20 X 1.5
7 P0573007 PRIMARY FILTER 28 P0573028 POWER CORD W/ PLUG
8 P0573008 PRE-FILTER 29 PN02M HEX NUT M10-1.5
9 P0573009 INLET AIR DOOR 30 P0573030 SWITCH
10 P0573010 CONNECTOR HINGE 31 P0573031 CASTER
12 PB09M HEX BOLT M8-1.25 X 20 32 P0573032 SKID CASTER
13 PW01M FLAT WASHER 8MM 33 PW03M FLAT WASHER 6MM
14 P0573014 MOTOR 34 PB83M HEX BOLT M6-1 X 16
15 PB09M HEX BOLT M8-1.25 X 20 35 PLW04M LOCK WASHER 8MM
16 PN03M HEX NUT M8-1.25 36 PW03 FLAT WASHER #10
17 PN03M HEX NUT M8-1.25 37 PLW03 LOCK WASHER #10
18 PW01M FLAT WASHER 8MM 38 PN04M HEX NUT M4-.7
19 PLW04M LOCK WASHER 8MM 39 PLW03M LOCK WASHER 6MM
20 PB07M HEX BOLT M8-1.25 X 25 40 P0573040 CAPACITOR 35 MFD 400 VAC
21 P0573021 DOOR LATCH 41 PN03M HEX NUT M8-1.25
-14-
G0573 Two Speed Floor Air Filter
Troubleshooting
Symptom Possible Cause Possible Solution
The air cleaner does not operate at all.
The air cleaner CFM output is reduced. 1. The filters are wet or clogged.
The air filter unit is noisy or vibrates. 1.The mounting is loose.
1. The power supply circuit breaker is
tripped.
2. No power to the control panel
3. Wiring is at fault
4. The control panel circuit board is at
fault.
5. The motor is at fault.
2. The airflow path is obstructed.
3. The control panel circuit board is at
fault.
4. The motor is at fault.
2. The unit is not level.
3. The fan or motor is loose.
1. Correct the cause for high current draw
and close the circuit breaker.
2. Replace the blown fuse in the control
panel.
3. Repair, replace wires, plugs and cables
as applicable; and make sure all electri
cal plugs and connections are secure.
4. Replace the circuit board.
5. Replace the motor.
1. Replace the primary filter and clean the
pre-filter.
2. Remove obstructions or add ducting.
3. Replace the control panel circuit
board.
4. Replace the motor.
1 Level the air cleaner unit.
2. Unplug the unit, remove the filters, and
tighten all loose fastners.
-
G0573 Two Speed Floor Air Filter
Disconnect power to the
machine when perform
ing any troubleshooting.
Failure to do this may
result in serious person
al injury.
-
-
-15-
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from
the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,
negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty
and any and all warranties that may be implied by law, including any merchantability or fitness, for any par
ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent
that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.
In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and
any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,
or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then
issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the
carton. We will not accept any item back without this number. Proof of purchase must accompany the
merchandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
-
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
-16-
G0573 Two Speed Floor Air Filter
WARRANTY CARD
Name _____________________________________________________________________________
Street _____________________________________________________________________________
City _______________________ State _________________________ Zip _____________________
Phone # ____________________
Model # ____________________ Order # _______________________ Serial # __________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop
better products and services. Of course, all information is strictly confidential.
1. How did you learn about us?
____ Advertisement ____ Friend ____ Catalog
____ Card Deck ____ Website ____ Other:
2. Which of the following magazines do you subscribe to?
____ Cabinet Maker
____ Family Handyman
____ Hand Loader
____ Handy
____ Home Shop Machinist
____ Journal of Light Cont.
____ Live Steam
____ Model Airplane News
____ Modeltec
____ Old House Journal
3. What is your annual household income?
____ $20,000-$29,000 ____ $30,000-$39,000 ____ $40,000-$49,000
____ $50,000-$59,000 ____ $60,000-$69,000 ____ $70,000+
Email ________________________ Invoice # _________________
____ Popular Mechanics
____ Popular Science
____ Popular Woodworking
____ Practical Homeowner
____ Precision Shooter
____ Projects in Metal
____ RC Modeler
____ Rifle
____ Shop Notes
____ Shotgun News
____ Today’s Homeowner
____ Wood
____ Wooden Boat
____ Woodshop News
____ Woodsmith
____ Woodwork
____ Woodworker West
____ Woodworker’s Journal
____ Other:
CUT ALONG DOTTED LINE
4. What is your age group?
____ 20-29 ____ 30-39 ____ 40-49
____ 50-59 ____ 60-69 ____ 70+
5. How long have you been a woodworker/metalworker?
____ 0-2 Years ____ 2-8 Years ____ 8-20 Years ____ 20+ Years
6. How many of your machines or tools are Grizzly?
____ 0-2 ____ 3-5 ____ 6-9 ____10+
7. Do you think your machine represents a good value? _____ Yes _____No
8. Would you recommend Grizzly Industrial to a friend? _____ Yes _____No
9. Would you allow us to use your name as a reference for Grizzly customers in your area?
Note: We never use names more than 3 times.
10. Comments: _____________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_____ Yes _____No
_________________________________________________________________________________
FOLD ALONG DOTTED LINE
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
Send a Grizzly Catalog to a friend:
Name_______________________________
Street_______________________________
City______________State______Zip______
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Buy Direct and Save with Grizzly® – Trusted, Proven and a Great Value!
Visit Our Website Today And Discover Why
Grizzly® Is The Industry Leader!
• SECURE ORDERING
• ORDERS SHIPPED WITHIN 24 HOURS
• E-MAIL RESPONSE WITHIN ONE HOUR
-OR-
Call Today For A
Full Color Catalog
FREE
Loading...