Grizzly D4646 User guide

Model D4646
Hose Reel
Instruction Sheet
Phone #: (360) 734-3482 • Online Tech Support: tech-support@shopfox.biz • Web: www.shopfox.biz
Items Needed
Open-End Wrench 13mm............................1
To reduce the risk of injury when using this tool:
• Make sure the incoming air pressure does not exceed the maximum rating of 300 PSI for the reel or hose/accessory you are using. Otherwise, the fittings could crack or explode.
• Protect your eyes by wearing safety glass­es or a face shield when assembling, mounting and using the hose reel.
Open-End Wrench 15mm............................1
Open-End Wrench 8mm .............................1
Adjustable Wrench ...................................1
Phillips Head Screwdriver Stubby #2 .............1
Air Compressor .......................................1
Air Hose (Connects Compressor/Hose Reel) .....1
Fasteners
7
16"............................. As Needed
Inventory
The Model D4646 is shipped fully assembled, as shown in Figure 1.
• Pressurized air may cause injury to exposed body parts. Never expose any part of your body to pressurized air.
• Make sure the hose reel is firmly mounted to a stable surface before pressurizing.
• Do not allow children to use the hose reel. Keep children clear of the work area.
Specifications
Max. Incoming Air Pressure ................. 300 PSI
Max. Hose Length ............... 50 ft. of
Air Fitting Size ...............................
Maximum Air Flow ........................... 25 CFM
3
8" Hose
1
4" NPT
Figure 1. Model D4646.
Mounting
1. Choose a location for mounting the hose
reel to a wall, floor, ceiling, etc. that uses a load-bearing structural member capable of supporting the combined weight of the reel, hose and any forces applied to it.
If you plan to install the hose reel on a
ceiling, place it 10 feet above the floor.
COPYRIGHT © SEPTEMBER, 2017 BY WOODSTOCK INTERNATIONAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
Printed in China
D4646 Hose Reel Instructions
2. Check that the hose guide roller bracket position (see Figure 2) is suitable for the chosen mounting position.
If the roller bracket or hose guide roller
position is not in the best position, refer to Changing Roller Bracket Position.
3. Mark the location of the mounting slots on the reel base (see Figure 2) in the chosen
location, then secure with (4) 7⁄16" grade 5
fasteners.
Outlet
Roller
Bracket
Bumper
Hose
Guide
6. Apply Teflon pipe tape or thread sealant to
the outlet hose threads, then attach the tool or nozzle.
7. Turn the air pressure ON, then use soapy
water to test for leaks. If any are found, turn the air pressure OFF, relieve the pressure from the hose, then repair the leaks before putting the hose reel into operation.
8. To adjust the hose bumper (see Figure 2),
pull some hose out until it clicks in place, loosen the screws on the bumper, slide it close to the hose guide, then tighten the screws.
Changing Roller Bracket Position
1. To change the hose guide roller bracket
position, pull out some hose until you hear a "click" to lock it.
Lock Nuts
(1 of 4)
Figure 2. Roller bracket and main components.
4. Remove the plastic plug from the inlet
valve (see Figure 3), apply Teflon pipe tape or thread sealant to the threads of the incoming air hose (not included), then connect it to the inlet valve.
Inlet
Valve
Figure 3. Location to connect incoming air
hose.
Mounting Slot
(1 of 4)
2. Remove (4) lock nuts and carriage bolts on the roller bracket (see Figure 2), rotate the bracket to any of the alternate positions, then re-install the carriage bolts and lock nuts.
Operation
1. Slowly pull the hose out of the reel assembly until you hear a "click."
2. To lock the hose, let it retract after you hear the reel click.
3. To unlock the hose, slowly pull the hose out until you hear no more clicking, then, while holding onto the hose, let it draw back until the bumper stops against the hose guide.
NOTICE
To avoid damaging the hose reel, always hold onto the hose while it is rewinding.
5. Connect the other end of the incoming air
hose to the compressor, if you have not already done so.
-2-
D4646 Hose Reel Instructions
Adjusting Spring Tension
1. DISCONNECT THE AIR SUPPLY FROM THE
HOSE REEL!
2. Pull approximately 2 feet of the hose out
and lock it.
3. Remove the bumper from the hose. Unlock
the reel and, while holding onto the drum edge, allow the drum to unwind and thread the hose out of the guide.
4. Lock the hose reel.
5. To increase tension on the hose, unlock
it and turn the drum clockwise (as viewed from the inlet valve); to decrease tension, unlock it, then turn the drum counterclockwise.
6. When the desired tension is achieved, lock
the hose reel, re-insert the hose through the guide, then re-install the bumper on the hose.
7. Unlock the hose and check the tension.
Adjust the position of the bumper if needed.
8. Connect the incoming air supply to the
inlet valve.
3. Remove the screw and nut that mount the hose clamp to the drum (see Figure 4).
Hose
Clamp
Drum
Opening
Inlet
Valve
Figure 4. Component locations for removing
hose.
4. Using an adjustable wrench, unthread the hose from the inlet valve, then remove the hose through the drum opening and hose guide.
5. Remove the hose clamp and spring guard from the old hose, then replace them on the new hose in the same location.
6. Apply Teflon tape to the threads of the incoming end of the new air hose, then thread the hose into the inlet valve.
7. Unwind any kinks in the new hose.
Spring Guard
Replacing Hose
1. DISCONNECT THE AIR SUPPLY FROM THE
HOSE REEL!
2. Unwind the hose completely, lock it in
place, making sure it will not rotate backward, then remove the bumper.
8. Feed the new hose through the drum opening, then position the spring guard over the drum opening.
9. Fasten the hose clamp onto the hose reel with the screws and nuts removed in
Step 3.
10. Re-install the bumper on the hose where it
was previously located, release the hose, and slowly allow it to wind back onto the reel.
11. Re-adjust spring tension as needed (refer to Adjusting Spring Tension).
-3-
Parts Breakdown & List
REF PART # DESCRIPTION REF PART # DESCRIPTION
Parts information is provided for service purposes only. Not all parts are available for purchase.
25
32
D4646 Hose Reel Instructions
34
7
30
6
33
31
36
35
17
5
29
28
4
22
24
1
23
3
2
27
26
38
16
15
40
39
MODEL D4646
HOSE REEL 3/8" x 50'
WARNING!
To reduce the risk of serious personal injury during use:
1. Read and understand the manual before starting or servicing.
2. Disconnect from air supply before servicing.
3. Wear ANSI-approved eye protection.
4. DO NOT exceed the maximum pressure rating of 300 PSI for this reel or the pneumatic accessory you are using.
5. Only use flexible hose to attach this hose reel to the air supply. Solid pipe may fail due to vibrations caused during reeling of the hose.
UNWIND
11
12
14 13
19
20
21
18
1 XD4646001 OUTSIDE SPRING COVER 23 XD4646023 LOCKING GEAR MOUNT 2 XD4646002 MAIN SPRING 24 XD4646024 LOCKING GEAR 3 XD4646003 INSIDE SPRING COVER 25 XD4646025 AXLE 4 XD4646004 OUTSIDE DRUM 26 XD4646026 LOCKING CAM 5 XD4646005 INSIDE DRUM 27 XD4646027 EXTENSION SPRING 6 XD4646006 BASE 28 XD4646028 FLAT WASHER 10MM 7 XD4646007 ROLLER BRACKET 29 XD4646029 HEX NUT M10-1.5 8 XD4646008 HOSE GUIDE BACK PLATE 30 XD4646030 FLAT WASHER 16MM 9 XD4646009 HOSE GUIDE BRACKET 31 XD4646031 HEX NUT M16-1.5 10 XD4646010 HOSE GUIDE ROLLERS 4PC 32 XD4646032 CARRIAGE BOLT M8-1.25 X 18 11 XD4646011 AIR INLET 3/8" 33 XD4646033 LOCK NUT M8-1.25 12 XD4646012 SWIVEL CONNECTOR 3/8" 34 XD4646034 HEX BOLT M8-1.25 X 16 13 XD4646013 EXT RETAINING RING 18MM 35 XD4646035 LOCK NUT M8-1.25 14 XD4646014 SWIVEL CONNECTOR WASHER 18MM 36 XD4646036 PHLP HD SCR M5-.8 X 10 15 XD4646015 LOCK NUT M6-1 37 XD4646037 LOCK NUT M5-.8 16 XD4646016 STANDOFF STUD M6-1 X 57 38 XD4646038 HOSE BUMPER 2PC 17 XD4646017 LOCK NUT M6-1 39 XD4646039 PHLP HD SCR M6-1 X 25 18 XD4646018 HOSE CLAMP 40 XD4646040 HEX NUT M6-1 19 XD4646019 PHLP HD SCR M5-.8 X 10 41 XD4646041 HOSE 3/8" X 50' 20 XD4646020 HEX NUT M5-.8 42 XD4646042 ID LABEL 21 XD4646021 CARRIAGE BOLT M6-1 X 45 43 XD4646043 SHOP FOX LOGO LABEL 22 XD4646022 LOCK NUT M6-1 44 XD4646044 HOSE DIRECTION LABEL
42
43
44
8
10
9
37
41
For questions contact Woodstock International Technical Support at (360) 734-3482, or send e-mail to:
tech-support@woodstockint.com.
-4-
Loading...