GreenWorks 2101000 Owner's Manual
Owner’s Manual
TOLL-FREE HELPLINE: 1-888-90WORKS
(888.909.6757)
2101000
Top mount Curved Shaft Trimmer
Read all safety rules and instructions carefully before operating this tool.
2
Introduction .................................................................................................................................. .2
General Safety Instruction ............................................................................................................ 3
Symbols ......................................................................................................................................... 7
Electrical ..................................................................................................................................... 10
Features ...................................................................................................................................... 11
Assembly .................................................................................................................................... 12
Operation .................................................................................................................................... 15
Maintenance ................................................................................................................................. 23
Warranty .................................................................................................................................... 26
Exploded View and Part List ...................................................................................................... 27
SPECIFICATIONS
Top mount Curve Shaft Trimmer
I
Cutting Path...................................................................................................................................15 in.
String Diameter................................................................................................0.080 in.(2.03mm) max.
Weight..........................................................................................................................................3.8Kg
nput............................................................................................ 120V, AC only, 60Hz, 7.5Amps
CONTENTS
Speed RPM........................................................................................................... 7500 RPM (no load)
Feed Type......................................................................................................................Bump ‘n’ Feed
General Safety Rules .................................................................................................................... 6
.................................................................................................................... 7Specific Safety Rules
3
GENERAL SAFETY INSTRUCTIONS
W A R N I N G
Read and understand all instructions before using this product. Failure to follow all
use without guard and handle in place.
READ ALL INSTRUCTIONS
• For safe operation, read and understand all instructions before using this product. Follow all
safety instructions. Failure to follow all safety instructions listed below, can result in serious
personal injury
• Do not allow children or untrained individuals to use this unit.
• Check the work area before each use. Remove all objects such as rocks, broken glass, nails,
wire, or string which can be thrown or become entangled in the machine.
• Use Safety Glasses – Always wear eye protection with side shields marked to comply with ANSI
Z87.1. Failure to do so could result in objects being thrown into your eyes, resulting in possible
serious injury.
• Always wear safety glasses with side shields. Everyday glasses have only impact resistant
lenses. They are NOT safety glasses. Following this rule will reduce the risk of eye injury. Use
face mask if operation is dusty
• Dress Properly – Use rubber gloves and substantial footwear is recommended when working
clothing, short pants, sandals, jewelry of any kind, or go barefoot.
• Secure long hair above shoulder level to prevent entanglement in moving parts.
• Keep children away – Keep all bystanders, children, and pets at least 50 ft. (15.25m) away.
•
drugs, or medication.
• Do not operate in poor lighting.
• Keep all parts of your body away from any moving part.
•
liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
• To reduce the risk of electric shock, this tool has a polarized plug (one blade is wider than the
equipment plug, extension cord receptacle, or extension cord plug in any way.
• Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators.
There is an increased risk of electric shock if your body is grounded.
• Avoid Dangerous Environments – Don’t expose power tools to rain or wet conditions. Water
entering a power tool will increase the risk of electric shock.
4
GENERAL SAFETY INSTRUCTIONS
• Warning – To reduce the risk of electric shock - Use outdoor extension cords marked W-A, W,
SW-A, SOW-A, STW-A, STOW-A, SJW-A, SJTW-A, or SJTOW-A. These cords are rated for
outdoor use and reduce the risk of electric shock.
• Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuit(s) or
outlet(s) to be used for the gardening appliance. Receptacles are available having built-in GFCI
protection and may be used for this measure of safety.
• Use Right Appliance - Do not force tool. Use the correct tool for your application. The correct
tool will do the job better and safer at the rate for which it is designed.
• Do not operate the equipment while barefoot or when wearing sandals or similar lightweight
footwear. Wear protective footwear that will protect your feet and improve your footing on
slippery surfaces.
• Do not use on a ladder or unstable support. Stable footing on a solid surface enables better
control of the unit in unexpected situations.
•
•
the switch trigger is not engaged before plugging in.
• Do not use tool if switch trigger does not turn it on or off. Any tool that cannot be controlled with
the switch trigger is dangerous and must be repaired.
• Disconnect Appliance – Remove appliance from power source before storing, servicing,
changing accessories such as cutting line. Such preventive safety measures reduce the risk of
starting the tool accidentally.
• Use only identical manufacturer’s replacement parts and accessories. Use of any other parts
may create a hazard or cause product damage.
• Maintain appliance with care – Replace string head if cracked, chipped, or damaged in any
way. Be sure the string head is properly installed and securely fastened. Keep cutting edge
sharp and clean for best performance and to reduce the risk of injury. Follow instructions for
lubricating and changing accessories. Inspect appliance cord periodically, and if damaged, have
it repaired by an authorized service facility. Inspect extension cords periodically and replace if
damaged. Keep handles dry, clean, and free from oil and grease. Failure to do so can cause
serious injury.
•
•
• Use only the manufacturer’s replacement string in the cutting head when using a string trimmer
attachment. Do not use any other cutting attachment, for example, metal wire, rope, or the like.
To install any other brand of cutting head to the string trimmer can result in serious personal
injury.
•
• Check damaged parts – Before further use of the tool, a guard or other part that is damaged
should be carefully checked to determine that it will operate properly and perform its intended
function. Check for alignment of moving parts, binding of moving parts, breakage of parts,
mounting and any other conditions that may affect its operation. A guard or other part that is
damaged must be properly repaired or replaced by an authorized service center to avoid risk
5
GENERAL SAFETY INSTRUCTIONS
of personal injury.
•
cut with the string head located over 30 in. (76 cm) or more above the ground.
• Store idle appliances - When not in use, power head should be stored indoors in a dry, locked
place out of the reach of children. Do not allow appliance to be used as a toy. Close attention is
necessary when used near children.
• Extension Cord - Make sure your extension cord is in good condition. When using an extension
cord, be sure to use one heavy enough to carry the current your product will draw. A wire gauge
size (A.W
.G.) of at least 14 is recommended for an extension cord 50 feet (15.25 m)
or less in length. A cord exceeding 100 feet (30.49 m) is not recommende d. If in doubt, use the
next heavier gauge. The smaller the gauge number, the heavier the cord. An undersized cord will
cause a drop in line voltage resulting in loss of power and overheating.
• Turn off controls before unplugging.
• Keep the air vents clean and free of debris to avoid overheating the motor. Clean after each
use.
• Stop the unit and disconnect the power source when not in use. Carry the unit with the motor
stopped.
• Store unplugged and out of the reach of children when not in use.
• Do not hang unit so that the switch trigger is depressed.
• Do not use multiple cords.
• Do not abuse the cord – Never carry the unit by the extension cord or yank extension cord to
disconnect unit. Keep the cord clear of operator and obstacles at all times. Do not expose cords
to heat, oil, water, or sharp edges. Do not handle plug with wet hands.
• If the power supply cord is damaged, it must be replaced only by the manufacturer or by an
authorized service center to avoid risk.
• If appliance is not working as it should , has been dropped, damaged, dropped into water,
return it to service center.
• Don’t grasp the exposed cutting blades or cutting edges when picking up or holding the
appliance.
• Don’t Force Appliance – It will do the job better and with less likelihood of a risk of injury at the
rate for which it was designed.
• When operating the trimmer keep extension cord behind trimmer.
• Do not put any objects into openings. Do not use with any openings blocked, keep free of dust,
• Save these instructions. Refer to them frequently and use them to instruct others who may use
this power tool. If you loan someone this power tool, loan them these instructions also.
6
W A R N I N G
Failure to follow all instructions listed below may result in electric shock, fire, and/or serious
personal injury.
SAVE THESE INSTRUCTIONS
• Read these instructions and the instructions for the power head thoroughly before using the
straight shaft trimmer attachment.
• Know the tool. Read and understand the operator’s manual and observe the warnings and
• Do not allow children or untrained individuals to use this unit.
• Wear safety glasses or goggles that are marked to comply with ANSI Z87.1 standard and
hearing protection when operating this unit.
• Wear heavy long pants, boots, and gloves. Do not wear loose fitting clothing, short pants,
jewelry of any kind, or go barefoot.
• Secure long hair so it is above shoulder level to prevent entanglement in any moving parts.
• Keep all bystanders, children, and pets at least 50 ft.(15.25 m) away.
Bystanders should be encouraged to wear eye protection.
• Stay alert, watch what you are doing, and use common sense when operating a power tool.
inattention while operating power tools may result in serious personal injury.
• Do not operate in poor lighting.
• Do not overreach. Keep proper footing and balance at all times. Proper footing and balance
enables better control of the tool in unexpected situations.
• Keep all parts of your body away from any moving part.
• For electric power head always remove power cord before making any adjustments or repairs.
• Inspect unit before each use for loose fasteners and damaged or missing parts. Correct before
using the trimmer attachment. Failure to do so can cause serious injury.
• Use only original manufacturer ’s replacement parts. Failure to do so may cause poor
performance, possible injury, and will void your warranty.
• Do not, under any circumstance, use any attachment or accessory on this product, which
operator’s manual.
• Avoid dangerous environments. Do not use the attachment in damp or wet locations. Do not
use in rain.
• Use the right attachment. Do not use attachment for any job except that for which it is intended.
• Replace string head if cracked, chipped, or damaged in any way. Be sure the string head is
properly installed and securely fastened. Failure to do so can cause serious injury.
•
•
GENERAL SAFETY RULES
SPECIFIC SAFETY RULES
•
•
• Keep string head below waist level. Never cut with the string head located over 30 in. (76 cm)
or more above the ground.
• Clear the work area before each use. Remove all objects such as rocks, broken glass, nails,
wire, or string which can be thrown or become entangled in the cutting line.
• Save these instructions. Refer to them frequently and use them to instruct others who may use
this tool. If you loan someone this tool, loan them these instructions also to prevent misuse of
the product and possible injury.
SYMBOL NAME EXPLANATION
Safety Alert Symbol
Precautions that involve your safety.
Read the Operator’s Manual
To reduce the risk of injury, user must read and
understand operator’s manual before using
t
his product.
Eye and Hear
ing Protection
Wear eye protection which is marked to comply
with ANSI Z87.1 as well as hearing protection
when operating this equipment.
Keep Bystanders Away
Keep all bystanders at least 50 ft. away.
Ricochet
Thrown objects can ricochet and result in personal
injury or property damage.
No Blade Alert
Do not install or use any type of blade on a product
displaying this symb
ol.
Some of the following symbols may be used on this product. Please study them and learn their
meaning. Proper interpretation of these symbols will allow you to operate the product better and
safer.
SYMBOLS
Wet Conditions Do not expose to rain or use in damp locations.
7
8
The following signal words and meanings are intended to explain the levels of risk associated with
this product.
SYMBOL SIGNAL MEANING
DANGER Indicates an imminently hazardous situation, which, if not avoided,
will result in death or serious injury.
WARNING Indicates a potentially hazardous situation, which, if not avoided,
could result in death or serious injury.
CAUTION Indicates a potentially hazardous situation, which, if not avoided,
may result in minor or moderate injury.
CAUTION ((Without Safety Alert Symbol) Indicates a situation that may
result in property damage.
SYMBOLS
SAVE THESE INSTRUCTIONS
9
Some of the following symbols may be used on this product. Please study them and learn their
meaning. Proper interpretation of these symbols will allow you to operate the product better and
safer.
SYMBOL NAME DESIGNATION/EXPLANATION
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
W Watt Power
min Minutes Time
SYMBOLS
SERVICE
service technician. For service we suggest you return the product to your nearest AUTHORIZED
SERVICE CENTER for repair. When servicing, use only identical replacement parts.
W A R N I N G
To avoid serious personal injury, do not attempt to use this product until you read
thoroughly and understand completely the operator’s manual. If you do not understand
the warnings and instructions in the operator’s manual, do not use this product. Call
GREENWORKS customer service for assistance.
W A R N I N G
The operation of any power tool can result in foreign objects being thrown into your eyes,
which can result in severe eye damage. Before beginning power tool operation, always
wear safety goggles or safety glasses with side shields and, when needed, a full face
shield. We recommend Wide Vision Safety Mask for use over eyeglasses or standard
safety glasses with side shields. Always use eye protection which is marked to comply
with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
Loading...