Greenheck Fan H-CUBE, H-GB, H-G, H-CUE User Manual

Download

High Wind and Hurricane Zone Fans

Models H-G, H-GB, H-CUE and H-CUBE

Belt and Direct Drive Exhaust Fans

The Hurricane season has brought a new level of attention to wind resistance in the

HVAC Industry. As you know, 2005 ended the worst hurricane season in history. With

this increased level of awareness, comes a greater need for high wind resistant roof

mounted equipment. To prevent water inﬁ ltration and building damage, it is critical that

roof top equipment stay afﬁ xed to the roof. But how do you know which product can

withstand high winds? Turn to Greenheck Models H-G, H-GB, H-CUE and H-CUBE to

ensure your exhaust fans stay afﬁ xed to the roof.

Hurricane winds start at 75 mph. At speeds of 150 mph, wind can exert a 61 pound per

square foot pressure or over 750 pounds of force on a fan and curb. Forceful winds

were the cause of most hurricane damage, exceeding $124 billion dollars in damage in

2005.

• Greenheck is leading the Hurricane Standards development

• Models H-G, H-GB, H-CUE and H-CUBE are third-party tested

• Finite Element Analysis (FEA) done by licensed Professional Engineer (including P.E. in Florida, Texas, Louisiana…)

• Full scale wind tunnel tested to 150 MPH

• Tested as an assembly

• No tie downs to roof are required

Severe weather calls for serious protection. We have the solution. Greenheck Models

H-G, H-GB, H-CUE and H-CUBE. Remember that these are the only tested and proven

high wind resistant fans. Don’t sacriﬁ ce quality and durability–specify the only fans that will

survive hurricane force winds.

November

2006

High Wind and Hurricane Zone Fans

Withstands winds up to 150 MPH

The Greenheck Models H-G and H-GB are downblast roof exhaust fans. Applications include general clean air and light moisture exhaust. The downblast design is ideal for all applications where air is discharged directly onto the roof surface. Models H-G and H-GB have been speciﬁ cally designed for high wind and extreme weather applications. Structural bracing on the interior of the fan, tabbed and riveted curb cap corners, and high strength materials provide the added strength required to withstand winds of up to 150 MPH. Standard with a 12 inch (305 mm) tall H-GPF curb, no tie downs to the roof are required. (Other curb options are available.)

Performance: For full performance listings refer to the H-G and H-GB

Catalog.

• Air performance up to 14,000 CFM (24,000 m3/hr).

• Pressure range from 0-2.75 inches wg (0-700 Pa).

• All fan sizes are tested in our AMCA Accredited Laboratory, and all models are licensed to bear the AMCA sound and air performance seal.

Standard Construction

• Internal Bracing - High strength internal support structure and bracing.

• Shroud - Heavy gauge reinforced drawn shroud with integral rolled bead for consistent material thickness and strength.

• Drive Assembly - Motor and drive frame are isolated from the airstream and mounted on true vibration isolators, and sized for 150% of maximum driven horsepower. (No steel to steel contact)

• Bearings - Pillow block design selected for a minimum average L10 life in excess of 100,000 hours (L50 life of 500,000 hours) at maximum cataloged speed.

• Disconnect - NEMA-1 disconnect is mounted and wired from the factory.

The Greenheck Models H-CUE and H-CUBE are upblast roof exhaust fans. Applications include restaurant exhaust and mild contaminants. The upblast design is ideal for all applications where it is important to discharge air away from the roof surface. Models H-CUE and H-CUBE have been speciﬁ cally designed for high wind and extreme weather applications. Structural bracing on the interior and exterior of the fan, tabbed and riveted curb cap corners, and high strength materials provide the added strength required to withstand winds of up to 150 MPH. Standard with a 12 inch (305 mm) tall H-GPF curb, no tie downs to the roof are required. (Other curb options are available.)

Performance: For full performance listings refer to the H-CUE and

H-CUBE Catalog.

• Air performance up to 14,700 CFM (25,000 m3/hr).

• Pressure range from 0-5 inches wg (0-1,250 Pa).

• All fan sizes are tested in our AMCA Accredited Laboratory, and all models are licensed to bear the AMCA sound and air performance seal.

Standard Construction

• Internal Bracing - Additional high strength internal bracing structure.

• External Bracing - Integral high strength mounted external bracing.

• Windband - Heavy gauge one piece windband with integral rolled bead, 100% welded to an aluminum curb cap.

• Drive Assembly - Motor and drive frame are isolated from the airstream and mounted on true vibration isolators, and sized for 150% of maximum driven horsepower.

• Bearings - Bearings are pillow block design selected for a minimum average L10 life in excess of 100,000 hours (L50 life of 500,000 hours) at maximum cataloged speed.

• Disconnect - NEMA-1 disconnect is mounted and wired from the factory.

•

Curb Cap - Heavy gauge with pre-punched mounting holes.

High Wind and Hurricane Zone Fans

Third Party Testing and Certiﬁ cations

The Greenheck high wind models have been thoroughly tested in accordance with recognized standards. With the H-G,

H-GB, H-CUE and the H-CUBE you are not only getting a superior product built by a quality company, you are getting

the assurance through a number of third party certiﬁ cations that the fan is capable of withstanding high winds.

•

State P.E. Calculations: Models have been

reviewed by state licensed professional engineers to ensure that they conform to the requirements of ASCE 7-02 Minimum Design Loads for Buildings and Other Structures, International Building Code and the Florida Building Code.

• Test Protocols: Models have been subjected

to an extensive testing regime. The models have been tested in accordance with ASTM E330 standards at design pressures that correspond to over 150 MPH wind loads.

• Computational Fluid Dynamics (CFD):

Greenheck leads the industry with cutting edge technology. Computational Fluid Dynamics simulates the airﬂ ow of high speed (150 MPH) winds over the surface of fans. The software records the force proﬁ le that the wind exerts on the fan, which can be used to complete Finite Element Analysis of the stresses in each unit. Models have been completely analyzed utilizing CFD to prove superior strength and resistance to high winds.

• Finite Element Analysis (FEA): Utilizing the

results from CFD analysis Greenheck can accurately predict the stress, strain, and deﬂ ection that result from high wind loads. A complete FEA utilizing CFD results is used to verify the fans capabilities and prove the results of professional engineer calculations.

When high wind forces are a concern, turn to Greenheck’s high wind models. Models H-G and H-GB downblast

roof exhaust fans and H-CUE and H-CUBE upblast restaurant exhaust fans are the only fans tested and certiﬁ ed to

withstand high winds. Don’t sacriﬁ ce quality and durability—specify the only fans that will survive hurricane force winds,

Greenheck models H-G, H-GB, H-CUE and H-CUBE.

Typical Installation

Fan to Curb Mounting

H-G Size

060 - 141 098 - 161 3 12

150 - 180 180 - 300 5 20

Fan to curb tie down is not required to meet 150 MPH wind loads for size 240 and smaller.

H-GB

Size

Fasteners

Per Side

Total

Fasteners

Model H-G

H-GB

Model H-CUE

Tie Down is

optional on

sizes 060 - 240

H-CUE

Size

060 - 161 098 - 161 3 12

180 - 200 180 - 240 5 20

- 300 9 36

H-CUBE

Size

Fasteners

Per Side

Total

Fasteners

Fastener

H-GPF or SD Curb

Fasteners on each side of the fan are to be installed with one fastener 4 inches (102 mm) from each edge and one fastener centered. The remaining fasteners are to be equally spaced.

Typical Installation

H-CUBE

Fastener

Concrete Deck Anchoring

Use 3/8 inch (10 mm) expansion anchor or equal into concrete.

Outside of Roof Curb

(1 inch (25 mm) less than

Fan Curb Cap)

1¼ inch (32 mm)

1¼ inch

(32 mm)

Minimum Concrete

Corner Detail

H-G Size

060 - 075 - 060 - 075 - 17 x 17 (432 x 432) 10½ x 10½ (267 x 267) 5 26 x 26 (660 x 660)

080 - 095 - - - 17 x 17 (432 x 432) 12½ x 12½ (318 x 318) 5 26 x 26 (660 x 660)

- - 080 - 095 - 19 x 19 (483 x 483) 12½ x 12½ (318 x 318) 5 28 x 28 (711 x 711)

101 - 121 071 - 131 098 - 131 098 - 131 19 x 19 (483 x 483) 14½ x 14½ (368 x 368) 5 28 x 28 (711 x 711)

131 - 141 141 - 161 141 - 161 141 - 161 22 x 22 (559 x 559) 18½ x 18½ (470 x 470) 5 31 x 31 (787 x 787)

150 - - - 26 x 26 (660 x 660) 18½ x 18½ (470 x 470) 5 35 x 35 (889 x 889)

160 - 180 180 - 200 180 - 200 180 - 200 30 x 30 (762 x 762) 20½ x 20½ (521 x 521) 7 39 x 39 (991 x 991)

- 220 - 240 - 220 - 240 34 x 34 (864 x 864) 26½ x 26½ (673 x 673) 7 43 x 43 (1092 x 1092)

- 260 - 300 - 300 40 x 40 (1016 x 1016) 32½ x 32½ (826 x 826) 7 49 x 49 (1245 x 1245)

All dimensions in inches (millimeters).

H-GB

Size

Strength of 2000 PSI

H-CUE

Size

H-GPF Curb Height

8 to 18 inches

(203 to 457 mm)

(Optional 24 inch

(610 mm) SD Curb)

Minimum 1¾ inch

edge distance

(44 mm)

H-CUBE

Size

1 inch (25 mm) Insulation

Roof Opening

5 inch (127 mm) Mounting Flange

Outside Flange

Fan Curb Cap Roof Opening

Fasteners one on each corner as detailed.

Each side at center of unit. Maximum fastener spacing of 8 inches (203 mm), add additional fasteners to satisfy.

2½ inch (64 mm) Embedment Recommended. Minimum 1

Center fasteners on ﬂ ange

Fasteners

Per Side

Outside Flange

/8 inch (41 mm).

Typical Installation

Metal Building/Steel Deck Anchoring

Outside of Roof Curb

(1 inch (25 mm) less than

Fan Curb Cap)

1¼ inch (32 mm)

Corner Detail

1¼ inch

(32 mm)

H-GPF Curb Height

8 to 18 inches

(203 to 457 mm)

(Optional 24 inch

(610 mm) SD Curb)

Roof Truss

1 inch (25 mm) Insulation

Roof Opening

Minimum 12 Ga. Steel

5 inch (127 mm) Mounting Flange

Outside Flange

Use #12-14 self-drilling screws or equal.

Fasteners one on each corner as detailed.

Each side at center of unit. Maximum fastener spacing of 8 inches (203 mm), add additional fasteners to satisfy.

Corrugated Roof Deck