Greenheck SP110L Installation Manual

Document 99045144B

Model SP110L/SP80L

®

Lighted Multi-Speed

Ceiling Exhaust Fan

Installation, Operation and Maintenance Manual

Installation, Operation and Maintenance Manual

Please read and save these instructions for future reference. Read carefully before attempting to assemble,

Please read and save these instructions for future reference. Read carefully before attempting to assemble,

install, operate or maintain the product described. Protect yourself and others by observing all safety

install, operate or maintain the product described. Protect yourself and others by observing all safety

information. Failure to comply with instructions could result in personal injury and/or property damage!

information. Failure to comply with instructions could result in personal injury and/or property damage!

Model SP110L / SP80L

Service Parts

Key

Greenheck

No.

10 435117 Grille Assembly (includes 11, 12, 13)
11 435111 Grille Spring (2 req’d)
12 435118 Lens
13 435119 Bulb, GU24 18W 3500K FL (2 req’d)

Part No.

1 435100 Mounting Frame
2 435101 Knockout Plate & Screws
3 435102 Housing
4 435103 Wiring Panel/Harness Assembly

5

6 435106 Duct Connector - 6"
7 435114 6" to 4" Reducer (model SP80L only)
8 435108 Blower Wheel
9 435115 Scroll Assembly

434112 Control Assembly & Motor (SP80L)
435113 Control Assembly & Motor (SP110L)

Description

Easy installation in both new construction and retrofit.

1

2

3

4

5

6

7

8

9

11

12

13

10

Table of Contents

Warnings and Cautions ............................................ 2

Typical Installation .................................................... 2

New Construction Installation .................................. 3

Retrofit Installation ...................................................7

®

Operation ................................................................ 11

Cleaning and Maintenance ..................................... 12

Troubleshooting ...................................................... 12

Our Commitment .................................................... 12

SP Ceiling Exhaust Fans

1

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer at the address or telephone number
listed in the warranty.

2. Before servicing or cleaning unit, switch power off
at service panel and lock the service disconnecting
means to prevent power from being switched
on accidentally. When the service disconnecting
means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the
service panel.

3. Installation work and electrical wiring must be
done by a qualified person(s) in accordance with
all applicable codes and standards, including fire­rated construction codes and standards.

4. Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of
fuel burning equipment to prevent backdrafting.
Follow the heating equipment manufacturer’s
guideline and safety standards such as those
published by the National Fire Protection
Association (NFPA), and the American Society
for Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code
authorities.

5. When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the
outdoors.

7. Do not use this fan with any solid-state speed
control device.

8. Acceptable for use over a tub or shower when
connected to a GFCI (Ground Fault Circuit
Interrupter) - protected branch circuit.

9. This unit must be grounded.

CAUTION

For general ventilating use only. Do not use to exhaust
hazardous or explosive materials and vapors.

1. This product is designed for installation in ceilings
up to a 12/12 pitch (45 degree angle). Duct
connector must point up. DO NOT MOUNT THIS

PRODUCT IN A WALL.

2. To avoid motor bearing damage and noisy and/
or unbalanced impellers, keep drywall spray,
construction dust, etc. off power unit.

3. Please read specification label on product for
further information and requirements.

CAUTION

NOT FOR USE IN A COOKING AREA

Typical Installation

• Installation is the same for:

Joists I-Joists Trusses

• Fits in 2" x 8" ceiling construction.

• Infinitely adjust the fan position between
joists from 14" to 24"
on center.

SP Ceiling Exhaust Fans

2

HOUSING

POWER
CABLE*

Seal gaps

around

Housing.

*Purchase

separately.

INSULATION*

(Place around and

over Fan Housing.)

FAN

ROUND

DUCT*

Seal duct

joints with

tape.

OR

ROUND

ELBOWS*

ROOF CAP*
(with built-in

damper)

Keep duct

runs short.

WALL CAP*

(with built-in

damper)

®

New Construction Installation

Tools needed

Power screwdriver with a Phillips bit
Phillips screwdriver
Flathead screwdriver
Pliers
Wire insulation stripper
Wire cutter

1 - Remove Packaging

Parts Bag holds
Knockout Plate
and six (6) screws

Remove
Instruction
Sheet

Materials needed

• 6" round metal ducting recommended for best
performance. Use of other ducting is acceptable but

may impact performance.

• Roof cap or wall cap (built-in damper recommended)

• Tape to seal duct connections

• Electrical wiring and supplies per local code
requirements

• 4W (max.) C7-type night light bulb

Remove CFL Bulbs

from protective packaging

Punch out Mask from

packaging. See Step 6.

2 - Install Mounting Frame

3

2

1

4

®

SP Ceiling Exhaust Fans

3

New Construction Installation

3 - Snap-in and Secure Housing

2

snap!

1

4

4 - Attach Duct Connector and Ducting

Top and bottom flanges
go outside Housing

Insert tab into slot
inside Housing

1

6" Ducting

Tape

Screws from Parts Bag

3

3

4" Ducting

Tape

Position Housing
between joists and
crimp channel
on both sides of
Mounting Frame
to lock Housing in
place. Do not crimp

Housing.

Screw from
Parts Bag

2

Tape

SP Ceiling Exhaust Fans

4

6" to 4" Reducer provided in select models

®

New Construction Installation

5 - Connect Wires and Install Knockout Plate

• Run 120VAC electrical wiring to the installation
location.

• Use proper UL-approved connectors to secure wiring
to the Knockout Plate provided in Parts Bag.

• Connect wires as shown in wiring diagram.

• Do not use a dimmer switch to operate the light.

Attach cable clamps to

1

Knockout Plate. Knockout Plate
mounts to outside of Housing
and may be oriented as desired.

3

Fan

(2) 2-FUNCTION

CONTROLS

MODE
SELECT
SWITCH

MASTER

ON/OFF
SWITCH

FAN

BLK

WHT WHT

LINE

IN

GRD GRD

BLK

Light

LIGHT

NIGHT
LIGHT

Connect wires

2

BLK BLU

WHT

RED RED (Rated Level)

BLK

BLK*

(* Adjustable Level)

LIGHT

REDRED

NIGHT
LIGHT

FAN

WHT

WHT

WHT

UNITSWITCH BOX

4

Screw from
Parts Bag

BLACK
WHITE
BLUE

MODE

SELECT

MASTER

ON/OFF

SWITCH

FAN

(2) 2-FUNCTION CONTROLS

(purchase separately)

®

RED
GROUND

(green or bare)

SWITCH

LIGHT

NIGHT
LIGHT

BOX

120 VAC

LINE IN

LIGHT

RECEPTACLE

WIRES

KNOCKOUT

PLATE

FAN

RECEPTACLE

LIGHT

RECEPTACLE

FAN

RECEPTACLE

WIRES

SP Ceiling Exhaust Fans

5

New Construction Installation

6 - Insert Mask and Finish Ceiling

• Install ceiling material.

• Cut out around Housing.

7 - Install Grille

Mask protects unit
during construction.
Remove before
installing Grille.

8 - Install Bulbs

1

2

3

3

Night Light

(purchase separately)

SP Ceiling Exhaust Fans

6

1

2

4

NOTE: See Page 11 for Operations, Page 12 for
Cleaning and Maintenance, and Troubleshooting.

®

Retrofit Installation

Tools needed

Power screwdriver with a Phillips bit
Phillips screwdriver Ruler
Flathead screwdriver Pencil
Pliers Drywall saw
Wire insulation stripper Claw hammer or pry bar
Wire cutter Utility knife

1 - Remove Packaging

Remove
Instruction
Sheet

Parts Bag holds
Knockout Plate
and six (6)
screws

2 - Switch Off Power

WARNING

Before removing existing fan, switch power off at
service panel and lock the service disconnecting
means to prevent power from being switched on
accidentally. When the service disconnecting means
cannot be locked, securely fasten a prominent
warning device, such as a tag, to the service panel.

Materials needed

• Tape to seal duct connections

• Existing rigid duct will require the addition of a short
length of flexible duct

• Electrical wiring and supplies per local code
requirements

• 4W (max.) C7-type night light bulb

Remove CFL Bulbs

from protective packaging

Punch out Mask from

packaging. See Step 12.

3 - Enlarge Ceiling Opening and Remove Existing Fan

12" (30.5 cm)

11" (27.9 cm)
parallel with joists

Existing ductwork and

1

wiring left in place

4 - Examine Wiring

Examine the existing wiring to make sure it is not
damaged. If any damage is found,

DO NOT CONTINUE INSTALLATION of this product.
Contact a qualified person(s) for repair.

2

®

SP Ceiling Exhaust Fans

7

Retrofit Installation

5 - Remove Blower Assembly

2

Both sides

6 - Remove Wiring Panel

1

Set aside
screw

1

Set aside
Blower Assembly

3

Set aside
Wiring Panel

2

3

7 - Insert Mounting Frame

4

3

1

Remove screws
from Mounting
Frame and set aside

5

2

Bend up
four tabs

SP Ceiling Exhaust Fans

8

®