Page 1
Stationary Louver
Drainable Blade
Application and Design
ESD-435 is a weather louver designed to protect air intake and
exhaust openings in building exterior walls. Design incorporates
drain gutters in the head member and horizontal blades to
channel water to the jambs where water is further channeled
through vertical downspouts and out at the sloped sill. The ESD435 is an extremely efficient louver with AMCA LICENSED
PERFORMANCE DATA enabling designers to select and apply
with confidence.
Standard Construction
Frame . . . . . . . .Heavy gauge extruded 6063-T5 aluminum,
4 in. x 0.081 in. nominal wall thickness
Blades . . . . . . . .Drainable design, heavy gauge extruded 6063-
T5 aluminum, 0.081 in. nominal wall thickness,
positioned at 37.5º angles on approximately
3 ¼ in. centers
Construction . . .Mechanically fastened
Birdscreen . . . . .3/4 in. x 0.051 in. fl attened expanded aluminum in
removable frame, inside mount (rear)
Finish . . . . . . . . . Mill
Minimum Size . . 12 in. W x 12 in. H
Maximum Single
Section Size . . . 120 in. W or 120 in. H (limited to 70 ft. sq.)
ESD-435
Options (at additional cost)
• A variety of bird and insect screens
• Blank off panel
• Clip angles
• Extended sill
• Filter rack
• Flanged frame
• Glazing adaptor
• Hinged frame
• Security bars
• Welded construction
• 0.125 nominal wall thickness
• A variety of architectural finishes including:
Clear anodize
Integral color anodize
Baked enamel paint
Kynar paint
*Width and height dimensions furnished
approximately ¼ inch under size.
Page 2
Free Area Chart (Sq. ft.)
Louver Height
Inches
102 4.17 6.87 12.27 14.97 20.38 22.40 27.81 30.51 35.91 38.61 43.34 46.04 51.45
108 4.42 7.29 13.02 15.89 21.62 23.77 29.50 32.37 38.10 40.97 45.98 48.85 54.58
114 4.68 7.71 13.78 16.81 22.88 25.15 31.22 34.25 40.32 43.36 48.66 51.70 57.77
120 4.93 8.13 14.53 17.73 24.13 26.53 32.92 36.12 42.52 45.72 51.32 54.52 60.91
12 18 30 36 48 54 66 72 84 90 102 108 120
12 0.29 0.48 0.85 1.04 1.41 1.56 1.93 2.12 2.49 2.68 3.01 3.20 3.57
18 0.54 0.89 1.59 1.94 2.64 2.91 3.61 3.96 4.66 5.01 5.62 5.97 6.67
24 0.79 1.31 2.33 2.85 3.87 4.26 5.29 5.80 6.83 7.34 8.24 8.75 9.78
30 1.05 1.72 3.08 3.76 5.12 5.63 6.98 7.66 9.02 9.70 10.88 11.56 12.92
36 1.30 2.15 3.84 4.69 6.38 7.01 8.70 9.55 11.24 12.09 13.57 14.41 16.10
42 1.56 2.57 4.59 5.60 7.62 8.38 10.40 11.42 13.44 14.45 16.22 17.23 19.25
48 1.84 3.03 5.41 6.60 8.98 9.87 12.25 13.44 15.82 17.01 19.10 20.29 22.67
54 2.10 3.46 6.19 7.55 10.28 11.30 14.03 15.39 18.12 19.48 21.87 23.23 25.96
60 2.35 3.88 6.93 8.46 11.51 12.65 15.71 17.23 20.28 21.81 24.48 26.01 29.06
66 2.61 4.29 7.67 9.36 12.74 14.01 17.39 19.08 22.46 24.15 27.11 28.80 32.18
72 2.86 4.72 8.43 10.29 14.00 15.39 19.11 20.96 24.67 26.53 29.78 31.64 35.35
78 3.12 5.14 9.18 11.20 15.25 16.76 20.81 22.83 26.87 28.89 32.43 34.45 38.50
84 3.38 5.57 9.96 12.15 16.54 18.19 22.57 24.76 29.15 31.34 35.18 37.38 41.76
90 3.66 6.04 10.79 13.16 17.92 19.70 24.45 26.82 31.57 33.95 38.11 40.48 45.23
96 3.91 6.45 11.53 14.07 19.14 21.05 26.13 28.66 33.74 36.28 40.72 43.26 48.34
Louver Width in Inches
ESD-435PERFORMANCE DATA
Stationary Louver Drainable Blade
Extruded Aluminum
Greenheck
Fan
Corporation
certifies that
the ESD435 louvers
shown
herein are
licensed to
bear the AMCA Seal. The
ratings shown are based
on tests and procedures
performed in accordance
with AMCA Publication
511 and comply with the
requirements of the AMCA
Certified Ratings Program.
The AMCA Certified
Ratings Seal applies to air
performance and water
penetration ratings.
Airflow Resistance (Standard Air - .075 lb/ft
Pa
in. wg
1
0.9
200
100
90
80
70
60
50
40
30
20
Static Pressure Drop
10
9
8
7
6
5
ft/min
m/s
Test Size 48 in. x 48 in.
0.8
Standard Air - .075 lb/ft
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.09
0.08
0.07
0.06
0.05
0.04
0.03
0.02
200200 300 400 500 600 700 800 9001000 2000 3000
3
Intake
Exhaust
2345678910
3
) Water Penetration (Standard Air - .075 lb/ft3)
Free Air Velocity
Model ESD-435 resistance to airflow (pressure drop) varies
depending on louver application (air intake or air exhaust).
Free area velocities (shown) are higher than average
velocity through the overall louver size. See louver selection
information.
Test size 48 in. x 48 in. Test duration of 15 min.
ml/m2 oz/ft2
0.30
Test Size 48 in. x 48 in.
80
60
40
20
Water Penetration per Unit Free Area
0
ft/min:
Test Period 15 minutes
0.25
Standard Air - .075 lb/ft
0.20
0.15
0.10
0.05
0.00
1000 1050 1100 1150 1200 1250 1300
5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6
m/s:
3
Free Area Velocity
The AMCA Water Penetration Test provides a method for comparing
various louver models and designs as to their efficiency in resisting
the penetration of rainfall under specific laboratory test conditions. The
beginning point of water penetration is defined as that velocity where the
water penetration curve projects through .01 oz. of water (penetration)
per sq. ft. of louver free area.
penetration for Model ESD-435 is 1151 fpm free area velocity.
The beginning point of water
*
These perfor mance ratings do not guarantee a louver to be weather proof
or stormproof and should be used in combination with other factors
including good engineering judgement in selecting louvers.
Page 3
ESD-435INSTALLATION DETAILS
Maximum Size and Installation Information
Maximum single section size for model ESD-435 is 120 in. W x 84 in. H or 84 in. W x 120 in. H (70 sq. ft). Larger openings require
field assembly of multiple louver panels to make up the overall opening size. Individual louver panels are designed to withstand
a 25 PSF wind-load (please consult Greenheck if the louvers must withstand higher wind-loads). Structural reinforcing members
may be required to adequately support and install multiple louver panels within a large opening. Structural reinforcing members
along with any associated installation hardware is not provided by Greenheck unless indicated otherwise by Greenheck. Additional
information on louver installation may be found in AMCA Publication #501, Louver Application Manual.
Stationary Louver Drainable Blade
Extruded Aluminum
Minimum Single Section Size
12 in. W x 9 in. H
Maximum Single Section Size
70 ft. sq.
Page 4
ESD-435PRODUCT DETAILS
Stationary Louver Drainable Blade
Extruded Aluminum
Page 5
ESD-435OPTION DRAWINGS
Stationary Louver Drainable Blade
Extruded Aluminum
FINISHES
Finish Type Description/Application Color Selection
2-coat 70% KYNAR 500®/HYLAR 5000® AAMA 2605 –
Dry fi lm thickness 1.2 mil. (AKA: Duranar®, Fluoropon®,
Trinar®, Flouropolymer, Polyvinylidene Fluoride, PVDF2)
2-coat 50% KYNAR 500®/HYLAR 5000® AAMA 2604
– Dry fi lm thickness 1.2 mil. (AKA: Acrofl ur®, Acrynar®)
Baked Enamel AAMA 2603 – Dry fi lm thickness 0.8 mil.
(AKA: Acrabond Plus®, Duracron®)
Integral Color Anodize AA-M10C22A42 (>0.7 mil)
Clear Anodize 215 R-1 AA-M10C22A41 (>0.7 mil)
Clear Anodize 204 R-1 AA-M10C22A31 (0.4-0.7 mil)
Industrial coatings
Mill
“Best.” The premier fi nish for extruded aluminum. Tough,
long-lasting coating has superior color retention and
abrasive properties. Resists chalking, fading, chemical
abrasion and weathering.
“Better.” Tough, long-lasting coating has excellent color
retention and abrasive properties. Resists chalking, fading,
chemical abrasion and weathering.
“Good.” Provides good adhesion and resistance to
weathering, corrosion and chemical stain.
“Two-step” anodizing is produced by following the normal
anodizing step with a second, colorfast process.
Clear, colorless and hard oxide aluminum coating that resists
weathering and chemical attack.
Clear, colorless and hard oxide aluminum coating that resists
weathering and chemical attack.
Greenheck offers a number of industrial coatings such as Hi-Pro Polyester, Epoxy, and Permatector®.
Consult a Greenheck Product Specialist for complete color and application information.
Materials may be supplied in natural aluminum or galvanized steel fi nish when normal weathering is
acceptable and there is no concern for color or color change.
Finishes meet or exceed AAMA 2605, AAMA 2604, and AAMA 2603 requirements. Please consult www.greenheck.com for complete information on standard and
extended paint warranties. Paint fi nish warranties are not applicable to steel products.
Standard Colors: Any of the 24
standard colors shown can be
furnished in 70% or 50% KYNAR
500®/HYLAR 5000® or Baked Enamel.
2-Coat Mica:
Greenheck offers 9 standard 2coat Mica colors. Other colors are
available. Consult Greenheck for
possible extra cost when selecting
non-standard colors or special
fi nishes.
Light, Medium or Dark Bronze;
Champagne; Black
Clear 5 years
Clear 1 Year
Copyright © 2007 Greenheck Fan Corporation
Standard Warranty
(Aluminum)
10 Years
(Consult Greenheck for
availability of extended
warranty)
5 Years
1 Year
5 years
Consult Greenheck
n/a
ESD-435
July 2007 Rev. 1
Greenheck Fan Corporation reserves the right
to make product changes without notice.
Loading...