1 High-frequency transformer T16 High pressure protection terminal HPP111 Terminal of neutral wire
Overload protection terminal of
2
compressor OVC-COMP
3 Terminal of temp sensor CN28 Electric heater band of chassis HEAT2-L13 Terminal of ground wire
High pressure protection terminal
4
HPP
Electronic expansion valve terminal
5
EV
7 Terminal of 4-way valve12 Protective tube FU101
Electric heater band of compressor
9
HEAT1-L
10 Terminal of live wire15
14 Choke L 101 and L102
Terminal of outdoor fan
OFAN-DC
7
8
9
11
● Bottom view
20
Technical Information
Service Manual
VIRU36HP230V1AO VIRU30HP230V1AO
1
2
3
4
5
6
7
8
181917 16 15 14 131211
No.NameNo.NameNo.Name
1 Neutral wire8 Interface B of electric heating 15 Terminal for high pressure protection
2 Grounding wire9 Terminal of low pressure valve16 Interface 2 of temperature sensor
3 Live wire10 Terminal of 2-way valve17 Interface of temperature sensor
4 Communication interface11 Terminal of 4-way valve 18 Terminal A of electronic expansion valve
5 Terminal of outdoor fan12 Terminal of compressor overload protection 19 Terminal B of electronic expansion valve
6 Terminal of high pressure valve13 Terminal for 2 high pressure protection
7 Interface C of electric heating 14 Terminal for low pressure protection
10
9
Technical Information
21
Introduction for icons on display screen
Introduction for buttons on remote controller
● Under of
time); Under on status, the display will show the corresponding set function icons.
● This is a general use remote controller, it could be used for the air conditioner
6. Function and Control
6.1 Remote Controller Introduction of YAN1F6F
ON/OFF button
1
MODE button
2
FAN button
3
SWING button
4
Service Manual
1
2
4
7
9
11
I feel
Operation mode
Auto mode
Cool mode
Dry mode
Fan mode
Heat mode
Clock
Sleep mode
Light
:Set temp.
:Outdoor ambient temp.
3
5
6
8
10
12
Temp. display type
:Indoor ambient temp.
Temp. di
splay type
TURBO button
5
▲
▲/ button
6
SLEEP button
7
TEMP button
8
WIFI button
9
LIGHT button
10
CLOCK button
11
TIMER ON / TIMER OFF
12
button
Set fan speed
Send signal
Turbo mode
8 heating function
Set temperature
WiFi function
Set time
TIMER ON /
TIMER OFF
Child lock
Up & down swing
Note:
which the model doesn't have, if press
original running status.
the corresponding button on the remote controller that the unit will keep the
tnereffid rof tnereffid si ruoloc eht models). After that, you can operate the air conditioner by using remote controller.
Under on status, pressing the button on the remote controller, the signal icon " "
will blink once and the air conditioner will give
conditioner.
f status, set temperature and clock icon will be displayed on the displa
off and light functions are set, the corre-
22
sponding icons will be displayed on the display of remote controller at the same
s
with multifunction; For some function,
Operation indicator " " is ON (red indicator, ● After putting through the power, .dnuos a tuo evig lliw renoitidnoc ria eht
on the display of remote controller ●
ria eht ot tnes neeb sah langis eht snaem hcihw ,dnuos ”ed“ a tuo
remit ,no remit fI( rellortnoc etomer fo y
Technical Information
Service Manual
ON/OFF button1.
2.
3.
Press this button again to exit turbo function and " " icon will disappear.
Press this button to turn on the unit. Press this button again to turn off the unit.
MODE button
Press this button to select your required operation mode.
FANHEATAUTOCOOLDRY
● When selecting auto mode, air conditioner will operate automatically according to ex-factory setting. Set temperature can’t be adjusted and
will not be displayed as well. Press "FAN" button can adjust fan speed. Press "SWING" button can adjust fan blowing angle.
● After selecting cool mode, air conditioner will operate under cool mode. Cool indicator on indoor unit is ON(This indicator is not available for
some models). Press "▲" or " " button to adjust set temperature. Press "FAN" button to adjust fan speed. Press "SWING" button to adjust fan
blowing angle.
● When selecting dry mode, the air conditioner operates at low speed under dry mode. Dry indicator on indoor unit is ON(This indicator is not
available for some models). Under dry mode, fan speed can’t be adjusted. Press "SWING" button to adjust fan blowing angle.
● When selecting fan mode, the air conditioner will only blow fan, no cooling and no heating. Press "FAN" button to adjust fan speed. Press
"SWING" button to adjust fan blowing angle.
● When selecting heating mode, the air conditioner operates under heat mode. Heat indicator on indoor unit is ON(This indicator is not
available for some models).Press "▲" or " " button to adjust set temperature. Press "FAN" button to adjust fan speed. Press "SWING" button
to adjust fan blowing angle. (Cooling only unit won’t receive heating mode signal. If setting heat mode with remote controller, press ON/OFF
button can’t start up the unit).
Note:
● For preventing cold air, after starting up heating mode, indoor unit will delay 1~5 minutes to blow air (actual delay time is depend on indoor
ambient temperature).
● Set temperature range from remote controller: 16~30
F
AN button
Pressing this button can set fan speed circularly as: auto (AUTO), low(
; Fan speed: auto, low speed, medium speed, high speed.
) ,medium( ), high(
).
Auto
Note:
● Under AUTO speed, air conditioner will select proper fan speed automatically according to ex-factory setting.
● Fan speed under dry mode is low speed.
● X-FAN function:Hold fan speed button for 2s in COOL or DRY mode, the icon “ ” is displayed and the indoor fan will continue operation
for a few minutes in order to dry the indoor unit even though you have turned off the unit. After energization, X-FAN OFF is defaulted. X-FAN
is not available in AUTO, FAN or HEAT mode.
This function indicates that moisture on evaporator of indoor unit will be blowed after the unit is stopped to avoid mould.
●Having set X-FAN function on:After turning off the unit by pressing ON/OFF button indoor fan will continue running for a few minutes.at low
speed.In this period,Hold fan speed button for 2s to stop indoor fan directly.
●Having set X-FAN function off: After turning off the unit by pressing ON/OFF button, the complete unit will be off directly.
4. SWING button
Press this button can select up&down swing angle. Fan blow angle can be selected circularly as below:
no display
(horizontal louvers stops at current position)
● When selecting " ", air conditioner is blowing fan automatically. Horizontal louver will automatically swing up & down at maximum angle.
● When selecting "
● When selecting "
● Hold " "button above 2s to set your required swing angle. When reaching your required angle, release the button.
Note:
● "
" may not be available. When air conditioner receives this signal, the air conditioner will blow fan automatically.
5. TURBO button
Under COOL or HEAT mode, press this button to turn to quick COOL or quick HEAT mode. "
Technical Information
" icon is displayed on remote controller.
23
6. ▲/▲ button
● Press "▲" or "
7.
9.
10.
12.
11
Press this button
n
actory
.
8.
that TIMER OFF is started up, press "TIMER OFF" button to cancel it.
remote controller will change quickly. On releasing button after setting is finished, temperature indica- tor on indoor unit will change
accordingly. (Temperature can’t be adjusted under auto mode)
● When setting TIMER ON, TIMER OFF or CLOCK, press "▲" or "▲" button to adjust time. (Refer to CLOCK, TIMER ON, TIMER OFF
buttons) When setting TIMER ON, TIMER OFF or CLOCK, press "▲" or "▲" button to adjust time. (Refer to CLOCK, TIMER ON, TIMER
OFF buttons)
SLEEP button
Under COOL, HEAT or DRY mode, press this button to start up sleep function. "
again to cancel sleep function and " " icon will disappear.
TEMP button
By pressing this button, you can see indoor set temperature, indoor ambient temperature or outdoor ambient temperature on indoor
display. The setting on remote controlleris selected circularly as below:
●
When selecting " " or no display with remote controller, temperature indicator on indoor unit displays set temperature.
●
When selecting " " with remote controller, temperature indicator on indoor unit displays indoor ambient temperature.
●When selecting "
Note:
●
Outdoor temperature display is not available for some models. At that time, indoor
temperature.
●
Its defaulted to display set temperature when turning on the unit.There is no display in the remote controller.
●
Only for the models whose indoor unit has dual-8 display.
When selecting displaying of indoor or outdoor ambient temperature, indoor temperature indicator displays corresponding tempe
●
▲
" button once increase or decrease set temperature 1
no display
" with remote controller, temperature indicator on indoor unit displays outdoor ambient temperature.
. Holding "▲" or "▲" button, 2s later, set temperature on
(1°F)
" icon is displayed on remote controller.
unit receives "
"signal, while it displays indoor set
Service Manual
units
rature and
WIFI button
Press " WiFi " button to turn on or turn off WiFi function. When WiFi function is turned on, the " WiFi " icon will be displayed on remote
controller; Under status of remote controller off, press "MODE" and " WiFi " buttons simultaneously for 1s,WiFi modulewill restore to f
default setting.
LIGHT button
Press this button to turn off display light on indoor unit. "
display light. " " icon is displayed.
.
CLOCK button
Press this button to set clock time. " " icon on remote controller will blink. Press "▲" or "
pressing of "▲" or "
Note:
Clock time adopts 24-hour mode.●
●
The interval between two operation cant exceeds 5s. Otherwise, remote controller will quit setting status. Operation for TIMER ON/TIMER
OFF is the same.
TIMER ON / TIMER OFF button
TIMER ON button
●
"TIMER ON" button can set the time for timer on. After pressing this button, "
blinks. Press "▲" or "
decrease 1min. Hold "▲" or "
started up, press "TIMER ON" button to cancel it.
● TIMER OFF button
"TIMER OFF" button can set the time for timer off. After pressing this button,"
controller blinks. Press "▲" or "
TIMER OFF setting will increase or decrease 1min. Hold "▲" or "
required time. Press "TIMER OFF" word "OFF" will stop blinking. " " icon resumes displaying. Cancel TIMER OFF. Under the condition
▲
" button, clock time will increase or decrease 1 minute. If hold "▲" or "▲" button, 2s later, time will change quickly
▲
"button to adjust TIMER ON setting. After each pressing "▲" or "▲" button, TIMER ON setting will increase or
▲
" button, 2s later, the time will change quickly until reaching your required time. Press "TIMER ON" to
" icon resumes displaying. Cancel TIMER ON: Under the condition that TIMER ON is
▲
" button to adjust TIMER OFF setting. After each pressing "▲" or "▲" button,
" icon on remote controller disappears. Press this button again to turn o
▲
" button within 5s to set clock time. Each
" icon stops blinking.
" icon disappears and the word "ON" on remote controller
" icon disappears and the word "OFF" on remote
▲
" button, 2s later, the time will change quickly until reaching your
24
Technical Information
Service Manual
Function introduction for combination buttons
1.
2.
according to setting time. ON/OFF button has no ef
3.
4.
Note:
● Under on and of
● Before setting
●
5.
rgy-saving
and
remote
Operation guide
1.
2.
3.
4.
5. Press "SWING" button to select fan blowing angle.
Press "▲" and "MODE" buttons simultaneously to start I FEEL
is
temperature
disappea
●
or
should be put within the area where indoor unit can receive the signal sent by the remote controller
f status, you can set TIMER OFF or TIMER ON simultaneously.
TIMER ON or TIMER OFF, please adjust the clock time.
After starting up TIMER ON or TIMER OFF, set the constant circulating valid. After that, air conditioner will be turned on or turned off
Energy-saving function
Under cooling mode, press "TEMP" and " CLOCK" buttons simultaneously to start up or turn off energy-saving function. When energy-saving
function is started up, "SE" will be shown on remote controller, and air conditioner will adjust the set temperature automatically according to
ex-factory setting to reach to the best energy-saving effect. Press "TEMP" and "CLOCK"buttons simultaneously again to exit ene
function.
Note:
● Under energy-saving function, fan speed is defaulted at auto speed and it cant be adjusted.
●
Under energy-saving function, set temperature cant be adjusted. Press "TURBO"
● Sleep function and energy-saving function cant operate at the same time. If energy-saving function has been set under cooling mode,
press sleep button will cancel energy-saving function. If sleep function has been set under cooling mode, start up the energy-saving
function will cancel sleep function.
8 heating function
Under heating mode, press "TEMP" and "CLOCK" buttons simultaneously to start
started up, " " and "8
"CLOCK" buttons simultaneously again to exit 8heating function.
Note:
● Under 8
● Under 8
● Sleep function and 8
sleep button will cancel 8
cancel sleep function.
● Under
Child lock function
Press "▲" and "
controller. If you operate the remote controller, the " " icon will blink three times without sending signal to the unit.
heating function, fan speed is defaulted at auto speed and it cant be adjusted.
heating function, set temperature cant be adjusted. Press
temperature display, the remote controller will display 46 heating.
▲
" simultaneously to turn on or turn off child lock function. When child lock function is on, " " icon is displayed on
" will be shown on remote controller, and the air conditioner keep the heating status
heating function cant operate at the same time. If 8heating function has been set under cooling mode, press
heating function. If sleep function has been set under cooling mode, start up the 8 heating function will
fect on setting. If you dont need this function, please use remote controller to cancel it.
button and the remote controller wont send signal.
up or turn off 8 heating function. When this function is
at 8. Press "TEMP"
"
TURBO" button and the remote controller wont send signal.
Temperature display switchover function
Under OFF status, press "
I FELL Function
set, the remote controller will send the detected ambient temperature to the controller and the unitwill automatically adjust the indoor
Please put the remote controller near user when this function is set. Do not put the remote controller near the object of high temperature
low temperature in order to avoid detecting inaccurate ambient temperature.When I FEEL function is turned on, the remote controller
After putting through the power, press "ON/OFF" button on remote controller to turn on the air conditioner.
Press "MODE" button to select your required mode: AUTO, COOL, DRY, FA N, HEAT.
Press "▲" or "
Press "FAN" button to set your required fan speed: auto, low, medium and high speed.
according to the detected tempera-ture. Press this two buttons simultaneously again to close I FEEL function and " " will
r.
▲
" button to set your required temperature. (Temperature cant be adjusted under auto mode).
▲
" and "MODE" buttons simultaneously to switch temperature display between and .
function and " " will be displayed on the remote controller. After this function
Technical Information
.
25
Service Manual
Replacement of batteries in remote controller
● During operation, point the remote control signal sender at the receiving window on indoor unit
●
hem.
indoor unit during operation.
● Replace new batteries of the same model when replacement is required.
● When you dont use remote controller for a long time, please take out the batteries.
● If the display on remote controller is fuzzy or theres no display, please replace batteries.
Press the back side of remote controller marked with "
1.
the cover of battery box along the arrow direction.
out
2.
Replace two 7# (AAA 1.5V) dry batteries, and make sure the position of "+" polar and "-" polar
are correct.
Reinstall the cover of battery box.3.
Note:
.
The distance between signal sender and receiving window should be no more than 8m, and there should be no obstacles between t
signal senderbattery
reinstall
remove
Cover of battery box
26
Technical Information
Service Manual
Introduction for icons on display screen
1
2
5
4
6
7
8
11
12
13
9
14
15
ON/OFF button
▲ button
3
FAN button
SWING button
TIMER OFF button
TURBO button
10
TEMP button
I FEEL button
button
CLOCK button
TIMER ON button
SLEEP button
Send signal
Turbo mode
8
heating function
Set temperature
Set time
WiFi
TIMER ON /
TIMER OFF
Child lock
Up & down swing
Set fan speed
ventilation operation
Light
Temp. display type
:Set temp.
:Outdoor ambient temp.
:Indoor ambient temp.
Sleep mode
Clock
Heat mode
Fan mode
Dry mode
Cool mode
Auto mode
Operation mode
I feel
X-FAN button
/
MODE button
▲
button
X-fan mode
health function
Introduction for buttons on remote controller
Note:
●
●
After putting through the power, the air conditioner will give out a sound. Operation indicator " " is ON (red indicator,the
colout is different for different models). After that, you can operate the air conditioner by using remote controller.
●
Under on status, pressing the button on the remote controller, the signal icon " "
on the display of remote controller
will blink once and the air conditioner will give out a “de” sound, which means the signal has been sent to the air conditioner.
● Under off status, set temperature and clock icon will be displayed on the display
of remote controller (If timer on, timer
off and light functions are set, the corre-
sponding icons will be displayed on the display of remote controller at the same
time); Under on status, the display will show the corresponding set function icons.
Press this button to turn on the unit. Press this button again to turn off the unit.
Press this button to increase set temperature. Holding it down above 2 seconds rapidly increases set temperature.
In AUTO mode, set temperature is not adjustable.
14
3
1
13
2
6
9
8
12
15
4
7
10
5
11
This is a general use remote controller, it could be used for the air conditioners with multifunction; For some function, which the
model doesn't have, if press the corresponding button on the remote controller that the unit will keep the
original running status.
6.2 Remote Controller Introduction of YV1FB9F
Technical Information
27
Loading...
+ 85 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.