Gree GJC07AB-K3MNB8A, GJH07AB-K3MNB8A, GJC07AB-K3RNB9A, GJH07AB-K3RNB9A, GJC09AB-K3MNB8A OPERATING INSTRUCTIONS

...

Room Air Conditioner

OPERATING INSTRUCTIONS

GJC07AB-K3MNB8A GJH07AB-K3MNB8A GJC07AB-K3RNB9A GJH07AB-K3RNB9A

GJC09AB-K3MNB8A GJH09AB-K3MNB8A GJC09AB-K3RNB9A

GJH09AB-K3RNB9A GJC18AC-K3RNB9B

GJH18AC-K3RNB9B GJH24AC-K3RNB9A

GJC12AD-K3MNB8A GJH12AD-K3MNB8A GJC12AD-K3RNB9A

GJH12AD-K3RNB9A GJC18AC-K3MNB8A GJH18AC-K3MNB8A GJC18AC-K3RNB9A

GJH18AC-K3RNB9A GJC24AC-K3MNB8A GJH24AC-K3MNB8A

GJC24AC-K3RNB9A

Please read this operating instructions thoroughly before

using your air conditioner and keep it for future reference.

NOTE:The concrete external appearance depends on the product.

66161256

CONTENTS

Thank you for choosing GREE air conditioner. Our design is based on the best efficiency and the lowest

noise operation and it can keep the room comfortable. Please read this operating manual carefully before operating the unit and keep it for consultation.

Structure mechanism and Installation

Function

Operating condition

power requirement Installation

Notes for installation

Operation procedure

Part identification 6 Air direction adjustment 6 Main switch operation procedure 7

Operation of wireless remote control 8 Operation tips 14

Care and maintenance

2 2 3 5

Caution 15

Care and maintenance 16

Trouble shooting guide 17 After service 18

Please read this operating manual carefully before operating the unit.

The figures in this manual may be different with the material objects, please refer to the material objects for reference.

Function

Introduction

Room temp.

Spring

Summer

Autumn

Winter

Wind direction

Cooling in summer

In hot summer, Air conditioner can cool down the room air by transferring heat out.

Window type room air conditioners of GREE can regulate the room temperature and dry the room. It is convenient for your work,study and life. It can be widely used in residence, shop, hotel, office, library and laboratory, and so on.

Dehumidifying in rainy or humid season

Without reducing the room temp., air conditioner can dehumidify and make the room air dry and comfortable.

Dry

Heating in winter

(Only for heat unit)

In cold winter, Air conditioner can heat up room air.

Exchange fresh air

Open storm door to keep the fresh air in the room.

Fresh Air

Operating Condition

Please operate air conditioner in the correct conditions as following.

COOL mode operation

Outdoor temperature should be in range of 18 to 43 , otherwise it is possible for air conditioner to breakdown. Room humidity should be lower than 90%. Otherwise, it is possible for air conditioner to dew at air conditioner surface and even drop water after running for so much time. But this is normal.

Power requirement

DRY mode operation

Outdoor temperature should be in range of 18 to 43 , otherwise it is possible for air conditioner to breakdown.

Rated voltage and voltage range:

The electric components will be damaged when the voltage is too high.

If the voltage is too low, the compressor will vibrate violently to damage the refrigerant system and easily cause the compressor and electric components not work.

The ground must be connected. Special socket must be used. Furthermore, the socket and wiring must conform to the wiring regulations. And the earthing method must be reliable. In fixed circuit, there must be electricity leakage protection switch of enough power capacity and air switch with enough space.

230V 10%

Earth wire To ensure the reliable earthing, please do not connect earth wire to the following places:

Water pipe

Installation

Installation precaution:

Window type conditioner is so valuable and the improper installation of it will cause a lot of damage! Please associate the professional technician to install the unit and don’t install it by yourself. Otherwise, we are not responsible for the damage like this.

Location:

The condensation water must be drained away conveniently.

Install air conditioner unit far away from TV set or radio etc. to avoid disturbing video or voice.

In salt and coastal area or place where is near thermal springs and polluted by sulphurous gas, or other special areas, please contact the seller before use.

Avoid a place where is possible for inflammable gas to leak out.

How to install:

Choose a location where there are no any obstacle surrounding

the unit, and the plug is accessible. Prepare the installation hole slightly bigger than unit size. Choose the installation space according to the following diagram.

Avoid other heat sources or direct sun light. Avoid a place where is easy for children to touch.

Don't use the unit in the immediate surrondings of

a laundry,a bath,a shower or a swimming pool.

For window type air conditioner with remote

control, install in a location where is strong electromagnetic disturbance, you should contact the

seller in advance to avoid the malfunction in use.

The distance of obstructions from window unit inside should be upper 300mm, lower 1500mm,

left 500mm,right 500mm, front1500mm.

Installation procedure:

1) Remove the sticker from the front panel.

2) Put the unit into the installation hole. When installing the unit, it should be slanted down to the back to avoid the enlargement of noise or vibration. (Slant between 6-10mm.) (Shown at right figure.) The installation place should be strong enough to avoid the enlargement of noise or vibration.

3) Fill up sews in the cabinet with sponge or foam.

Installation assistance:

Horizontal line

Wall

Sunshade board

Wooden frame

Use iron support The installation hole should be strong enough to support the air conditioner. If it cannot, iron support has to be used outdoors. Iron support should be fixed on the building (Shown at right figure.) Use sunshade board Air conditioner should avoid anything to be dropped into it and avoid direct sunshine. If there is no cover on it, you should contact the seller for installing the sunshade board. When installing the sunshade board, don’t let it block the air inlet at the side grille.

Rubber plate

Support

Horizontal line

Drain water:

To get the maximum cooling efficiency, the air conditioner is designed to splash the condensation water on the condenser coil.

To the cooling only unit,If the splashing sound annoys you, you can provide an outside drain by using the follo

-wing procedure, whichmay however cause a small loss of performance.

1. Slide out the chassis from the cabinet.

2. Remove the rubber plug from the body base plate.

3. Install the drain pan to the corner of the cabinet with 2 screws.

4. Connect the drain hose to the outlet on the drain pan bottom.

5. Slide the chassis into its original place in the cabinet.

Note:

Drain pan and drain hose must be installed before using reverse cycle models.

Drain hose or tubing can be purchased locally to satisfy your particular needs.

Notes for installation

Remove

Before removing air conditioner to the other place, you should contact the seller firstly. Then it must be done under the direction of the professional technician. In addition, the charge of this must be paid.

Noise

Install in a location where is firm enough to avoid the enlargement of noise and vibration. Don’t put anything in front of the outlet of outdoor unit to avoid increasing noise. Be sure that hot air or noise will not inconvenience neighbors. Please contact the seller as soon as there is strange noise during operation. Please use the safety support.

Electric wiring

Must connect with ground reliably.

The exclusive circuit must be used. But removable socket can’t be used because poor

contact of it can cause over heat or fire.

Don’t pull the power cord strongly.

In fixed circuit, there must be electricity leakage protection switch and leakage current is less than 30mA.

Connecting method between air conditioners and power cord and interconnecting method

of each individual element with one another should accord with wiring diagram on the unit.

The air conditioner should be installed in accordance with national wiring regulation.

An all-pole disconnection switch having a contact separation of at least 3mm in all poles should be connected in fixed wiring

Air switch (thermal-magnetic breaker) should be installed in the circuit.

If the supply cord is damaged,it must be replaced by the manufacturer or your dealer

or a qualified person to avoid a hazard. All The dectrical work must be done according to the local wiring regulations.

GJH18AC-K3RNB9A, GJC18AC-K3RNB9A can be connected only to a supply with system impedance no more than 0.225 ohm. In case necessary, please consult your supply authority for system impedance information.

GJH18AC-K3RNB9B, GJC18AC-K3RNB9B can be connected only to a supply with system impedance no more than 0.243 ohm. In case necessary, please consult your supply authority for system impedance information.

+ 14 hidden pages