Page 1
Assembly Instructions for the Rolling Harrow
Verti-Till
9/23/03
Your initial action is to bolt the rolling harrow drop extensions [(62) 589-128H] to the back 4x4
tube on the Verti-Till with 5/8x4x5 ½ U-Bolts [(63) 806-184C] 5/8” hex nuts [(25) 803-021C] and 5/8”
lock washers [(26) 804-022C]. Be sure to place them as shown in Figure 1. Do not tighten these bolts
at this time. Your next step is to U-Bolt the drag frame(s) [(61) 589-129H or 589-130H] to the drop
extensions. Be sure everything is placed in the correct dimensions and tighten everything down at this
time.
The rolling harrow gangs shown in figure 2, come to you partially assembled. To finish
assembly, refer to the table in figure 2 and assemble accordingly. Start by locating the correct rolling
harrow tube, center it over your partial assembly on the bearing hangers [(52) 589-142H], and mount the
tube using 5/8x3x4 ½ U-bolts [(44) 806-183C] with a lock washer and nut. Your next step is to locate
the ball joint assemblies [(59) 589-064H]. Figure 2 shows you the dimensions to mount the ball joint
assemblies on the rolling harrow tube. Count the number of each assembly in figure 1 and assemble
accordingly.
Mount the rolling harrow brackets [(60) 589-057H] to the under side of the drag frames
according to the dimensions in figure 1, using a 5/8x3x4 ½ U-bolt [(44) 806-183C] with a lock washer
and nut. You may tighten the U-bolts on all the brackets that are closest to the rear of the machine.
Leave the front brackets loose to slide until the rolling harrow assemblies are hung under the frame. Use
the 1x4 hex bolt and 1” nylock nut through the harrow brackets (589-057H) and ball joint assemblies
[(59) 589-064H] to hang the rolling harrow assemblies under the frame. Be careful to put the proper
gang in the proper location and be sure that the assemblies are oriented correctly as shown in figure 2.
When all gangs are hung under the frame, tighten the remaining U-bolts.
Page 2
Page 3
Page 4
VERTI-TILL FINISHING ATTACHMENTS
ROLLING HARROW
REF # DESCRIPTION PART NO. 5300 7300
ROLLING HARROW GANG ASSEMBLIES
7 WHEEL ROLLING HARROW GANG 589-065K
8 WHEEL ROLLING HARROW GANG 589-066K
9 WHEEL ROLLING HARROW GANG 589-067K 1
10 WHEEL ROLLING HARROW GANG 589-068K 2 2
11 WHEEL ROLLING HARROW GANG 589-071K 2
12 WHEEL ROLLING HARROW GANG 589-095K
13 WHEEL ROLLING HARROW GANG 589-117K
(INDIVIDUAL PARTS INCLUDED IN GANG ASSEMBLIES)
29 3/4 LONG X 1/2 TINE STOP/SPACR 550-134D 6 8
28 1/2 LONG X 1/2 BOLT SPACER 585-013D 6 8
50 SPIDER WHEEL LARGE 589-055H 12 18
SPIDER WHEEL OFFSET @ 22.5 589-056H 14 20
SPIDER WHEEL SMALL 589-094H 3 4
51 BEARING, 1 1/4" SQUARE 822-209C 6 8
52 BEARING HANGER 589-142H 6 8
53 SPACER - LONG 589-026D 26 38
54 SPACER - SHORT 589-027D 6 8
55 43 7/8 ROLLING HARROW SHAFT 589-014D 0 0
49 5/8 ROLLING HARROW SHAFT 589-015D 0 0
55 1/2 ROLLING HARROW SHAFT 589-016D 1 0
61 3/8 ROLLING HARROW SHAFT 589-017D 2 2
67 1/8 ROLLING HARROW SHAFT 589-029D 0 2
73 ROLLING HARROW SHAFT 589-050D 0 0
79 3/8 ROLLING HARROW SHAFT 589-056D 0 0
30 ZERK GUARD ROLLING HARROW 589-085D 6 8
56 1" THREADED STUB SHAFT 800-364C 3 4
57 WASHER, RECT 1/4X1" FLAT 585-057D 6 8
49 PIN, 1/2" HR RND 1 3/8" LONG 585-056D 3 4
65 TREADER SHAFT 1/8" SPACER 585-066D 3 4
58 48" ROLLING HARROW TUBE 589-018D 0 0
54" ROLLING HARROW TUBE 589-019D 0 0
60" ROLLING HARROW TUBE 589-020D 1 0
66" ROLLING HARROW TUBE 589-021D 2 2
72" ROLLING HARROW TUBE 589-031D 0 2
78" ROLLING HARROW TUBE 589-049D 0 0
84" ROLLING HARROW TUBE 589-055D 0 0
31 NUT HEX TOP LOCK 1/2-13 PLT 803-342C 24 32
40 1/2" HEX NUT 803-020C 3 4
41 1/2" LOCK WASHER 804-015C 3 4
42 1/2 x 1 1/2" CARRIAGE BOLT 802-106C 12 16
27 1/2 x 2" CARRIAGE BOLT 802-129C 12 16
45 1/2 x 2 1/2" HEX BOLT 802-130C 3 4
25 5/8" HEX NUT 803-021C 24 32
26 5/8" LOCK WASHER 804-022C 24 32
44 5/8 x 3 x 4 1/2" U-BOLT 806-183C 12 16
46 1" FLAT WASHER 804-028C 6 8
47 1" LOCK WASHER 804-027C 3 4
48 1" NYLOCK HEX NUT 803-038C 3 4
ROLLING HARROW GANG MOUNTING HARDWARE
59 BALL JOINT BRACKET 589-064H 6 8
60 BRACKET - ROLLING HARROW 589-057H 6 8
61 12 1/2' VERTI-TILL DRAG FRAME 589-129H 1
17 1/2' VERTI-TILL DRAG FRAME 589-130H 2
62 ROLLING HARROW DROP EXT 589-128H 4 6
36 1 x 4 HEX BOLT 802-073C 6 8
48 1" NYLOCK NUT 803-038C 6 8
25 5/8" HEX NUT 803-021C 80 112
26 5/8" LOCK WASHER 804-022C 80 112
63 5/8 x 4 x 5 1/2" U-BOLT 806-184C 8 12
44 5/8 x 3 x 4 1/2" U-BOLT 806-183C 32 44
4/21/2004
Verti-Till Rolling Harrow.xls
Loading...