Page 1
P1
mz-8H HoTT
◎ GRAUPNER
8th F, 202 Dong, Chunui Techno-Park II, 202,Chunui-
Dong, Wonmi-Gu,
Bucheon-Si, Gyeonggi-do, SOUTH KOREA.
TEL: 070-7863-3675 FAX : 070-7863-3670
E-mail: service@openhobby.com
FUNCTION
Main function and Channel
Basic 4 Channels and added 6 Channels.
6 Channel is as below.
① LED : ON / OFF
-> CH8 1100us / 1900us
② SPEED : Attitude mode / Rate mode
-> CH5 1100us / 1900us
③ SNAP : Taking pictures
-> CH9 1100us (1500us nothing)
④ RECORD : Film movies
-> CH9 1900us
⑤ FLIP : Use the button on top left of image (360° FLIP)
-> CH10 1100us / 1900us
now channel 10, later channel 7, (Alpha 150 not active
in autopilot mode as soon as GPS is connected it will be
channel 6 coming home function)
⑥ 3D / EASY : Use the button on top right of image
(180° revolution and additional function)
-> CH6 1100us / 1900us
CH6, when AKRO3D is adjusted in the receiver, for
normal flight mode with GPS (Alpha 150) it will be
autopilot function
⑦ 2.4GHz Quad with 6-Axis Gyro
⑧ You can check real time flight screen with FPV
Camera and 5.8GHz RF. And you can monitor with
Goggle and other monitors.
⑨ You can attach camera and video module by
choosing option. You can take a video on the radio
using Photo & Video button.
mz-8
Frequency band 2404.056MHz ~2479.095 MHz
Modulation FHSS
Transmission output about 1mW
Temperature range -10 … +55 ℃
Antenna Monopole Antenna
Battery AA Size x 3 pcs
Operating voltage 3.6 … 4.8V
Output voltage about 50mA
Dimension 151 x 134 x 63.7 mm
Weight about 260g (Incl. battery)
Page 2
P2
Transmitter manual
Operating transmitter
- Power on : Pull Slide switch up
- Power off : Pull Slide switch down
1) Flip Function
I
f you push Flip button, buzzer will ring with 0.5 seconds
intervals.
To rotate a full 360 degrees,
push Flip button and when
buzzer starts rin
ging, move stick of transmitter to
maximum position quickly.
2) 3D & Easy Function
W
hen you push 3D button, buzzer will ring twice with 1
second intervals.
3D function is for 180 degrees flight.
T
same function with Flip.
Flip Button
Light
Button
Trim
o operate, use
3) Attitude Function
W
hen you push Function button, one short sound rings.
This function is attitude
control of general quad copters.
4) Rate Function
W
hen you push Function button, two short sound rings.
Y
ou can do rotation and normal flight on 3D flight mode
with
transmitter. Function is same with 3D helicopter.
Power Switch
MZ
-8
3D / Easy Button
Status & Function
Camera Record Button
Camera Snep
Trim
Page 3
P3
LED Function
< LED arrangement of transmitter >
1) LIGHT ON / OFF Function
Yellow Led
① When the lights are off, LED
stay OFF
②
When the lights are on, LED stay ON condition.
（default status）
2) SPEED Attitude and Rate Function
Red Led
① Attitude mode : LED
stay ON condition.
status）
② Rate mode : LED
blinks with one second intervals.
3) Camera function （O
ptional feature
Green Led
① When power is switched on, stay On
condition.
--> Photograph mode （
default status
②
When movie button is pressed, LED blinks with one
second intervals.
--> Video mode
4) Binding
and Transmitter status function.
Red Led （Status Led
）
① Show Power and Binding
② If device is not bou
nd, LED blinks with 0.5 second
intervals.
③ If device is bound, LED stay ON
condition
condition.
（default
）
）
.
Status Discription
Red LED
Bind range
Bind status (No
bind)
blinking (1s)
Bind Success,
RX receive OK
Range Test
fast blinking
Error
Low Voltage
fast blinking
Sensor Warring
Rx Voltage,
Temp Error
fast blinking
Receive rate low,
No RX
slow blinking
Factory Error
Normal mode
Trim inc/dec
Trim 0%
Program
mode
Program mode
start
1 blink
Program mode
exit
Servo Reverse
(Normal)
Servo Reverse
(Reverse)
ATV 100%
Fail Safe mode
start
2 blink
Fail safe (trim dn,
hold)
Fail safe (trim up,
fail)
Stick
Calibration
Calibration mode
start
3 blink
Stick move done
3 blink
(3times)
Dead range set
Green LED Buzzer
low beep(1)
on
low beep(2)
on
low beep(2)
/2sec
High beep(4)
/2sec
High beep(3)
/2sec
High beep(2)
/2sec
High beep(1)
/2sec
Low beep(1)
/2sec
low beep(1)
/click
High beep(1)
/click
low beep(1)
low beep(1)
1 blink
(5times)
low beep(1)
2 blink
(5times)
low beep(2)
High beep(1)
low beep(2)
1 blink
(5times)
low beep(1)
2 blink
(5times)
High beep(1)
3 blink
(3times)
low beep(2)
Dead
blink/3sec
Page 4
P4
Normal Mode
(1) Basic Operation
- When Power on, t
he last used memory will be bound
Receiver.
-
In case of No Receiver connection, if you press the
button of left stick for 1sec,
it will search Receiver.
- if Receiver
is not searched, it will be repeated until
Receiver, and you can bind with new Receiver by
pressing BIND/LED Switch.
(2) BIND mode
In case of no having receiver, which is already saved in
memory, then you can bind with new receiver by
pressing BIND Switch.
If Receive Signal is normal, RED LED wi
In case of Waiting Receiver or Range warning, RED
LED will be slow blinked.
(3) Range Test mode
Functional switch:
Press shortly button of
SNAP once.
A
fter Binding with Receiver, if you shortly press this
functional Switch, Range Test mode will operate for
90sec.
While operating Range mode, if you shortly press this
switch, Range test mode will be ended.
A
t Range mode operation, RED LED will blink quickly
and make buzzer sound.
After 90sec, Beep sound will be
occurred
enter to Main Mode.
(4) Low Battery Voltage warning
RED LED will do fast blinking. (
RED LED indicate State)
At under 3200V, Warning will be announced and at
3300V, warning will be removed.
3Cell Alkaline Battery will be used.
Important Point :
While Binding, Transmitter should always have distance
from the Receiver. At least 1m should h
ave.
Otherwise, it might be connected to Return channel, and
do malfunction.
to
find
ll be turned On.
SPEED +
one time, and
Program Mode
(
workable only at Binding condition
(1)
Condition of Basic Operation
Enter to Program mode
simultaneously for 2sec.
Release Program mode
simultaneously for a second.
Indication of
Program mode : Red Led
once per a second interval
.
Program mode : Blink
once per a second interval
(2) Saving Data
50pcs of last used
Data could be saved.
(3) Adjustment of
Servo End
In
case of Stick Calibration, Default will
value, Customer can adjust trim as below
- 100% --
> 1100us ~ 1900us
At Max. or Min. Positi
on of Stick,
Range of Trim is available
0% ~ 100%
I
f move to 100% position, High Beep sound will be
occurred once.
-
Red Led will be blinked once per a second interval
Program mode : Blink
once per a second interval
(4) Servo Reverse Set
This is used
when change Servo direction.
All sticks
are on neutral pos
switch to Max. or Min. Posi
tion.
I
f press Power switch with pressed trim switch to Max. or
Min. position, Normal mode and Reverse mode will be
changed.
- Indication of Servo Rece
i
blinked
once per a second interval
-
Normal mode : Green LED will be blinked once per a
second interval.
)
: Press two Stick Switch
: Press two Stick Switch
will be blinked
Position
be 100%. At this
way.
adjust Trim Switch
~ 150%.
ition, and move the trim
ver mode : Red Led will be
Page 5
P5
-Reverse mode :
Green LED will be blinked
second interval.
Program mode : Blink
once per a second interval
Normal mode : Blink
once per a second interval
(Repetition 5times)
Reverse mode : Blink twice per a second interval
(Repetition 5times)
(5) Fail Safe Set
Press right
stick switch for a second at Program mode.
Press trim button
per channels and select Fail pos mode
and Hold it.
Whenever press Trim button, Setting-
condition will be
transferred to Receiver.
If press right-
stick switch for a second, Fail safe setting
mode will be ended.
- Indication of Fail Safe mode : RED
LED will be blinked
twice per a second interval.
- Pos mode :
If Trim is UP, it is a Fail safe mode, and
Green LED will be blinked twi
ce per a second interval.
(Repetition 5times)
- Hold mode : If Trim is Down, it is a
Green LED will be blinked once per a second interval.
(Repetition 5times)
Program mode (Failsafe mode):
Blink twice per a
second interval
Hold mode : Blink
once per a second interval (
5times)
Pos mode :
Blink twice per a second interval (
5times)
twice per a
Hold mode, and
Repetition
Repetition
How to do Stick Calibration
(1) Enter to
Stick Calibration Mode
Turn On the Radio
, in state of
I
f enter to Mode, RED LED will blink 3 times.
Stick calibration mode
: Blink 3 times per a second
interval
(2) Set Stick Calibration
Move all sticks from side to Side and
position.
A
fter operated last stick, hold it to middle position for
3Seconds.
If Set is done,
Red and Green LED will blink 3Times at
same time.
Stick calibration mode
Blink 3 Times per a second interv
※
after that, it is moved to Dead Range set mode
automatically.
(3) Dead range set
This is for keep Neutral
position
accurate Neutral value.
Dead range set about Neutral position, is set by trim
switch up and down.
It can be settable
from 1 to 6 steps.
※ in case of Throttle CH1
, there is no spring, Do not set.
(
only set for CH2, CH3, CH4
Green LED will blink depends on Neutral set steps.
F
or example, if you set Dead range to 6%, LED will
blink 4time
s per a second interval.
Dead range mode
Blink 3times per a sec interval.
Dead range set
Blinks depends of setting value
I
f set is done, press left stick button for 2 sec.
pressing left stick switch.
back to middle
Stick move done
al
, in case of they have no
( 0, 2, 4, 6, 8, 10% )
)
(6 steps)
Page 6
P6
안안안안
(1) KC 인증
Graupner mz-8 Transmitter
KCC
인인인인
: MSIP-CRM-sjr-16007500
(2)
Conformite Europeenne
Product(s): Graupner mz-8 Transmitter,
(3) FCC Information
Graupner mz-8 Transmitter
FCC ID: SNL-16007500
FCC Statement
1. This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party
responsible for compliance could void the user‘s authority to operate
the equipment.
• NOTE
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- _Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
• FCC radiation exposure statement
This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment.
◎
Notes on environmental protection
This symbol on the product, user
manual or packaging indicates that this
product must not be disposed of with
other household waste at the end of its
life. It must be handed over
to the applicable collection point for the
recycling of electrical and electronic
equipment.
The materials are recyclable as marked. By recycling,
material reusing or other forms of scrap usage you are
making an important contribution to environmental
protection.
Batteries and accumulators must be removed from the
device and disposed of at an appropriate collection point.
Please inquire if necessary from the local authority for
the appropriate disposal site.
Loading...