Belden, Belden Sending All The Right Signals, and the Belden logo are trademarks or
egistered trademarks of Belden Inc. or its affiliated companies in the United States and
r
other jurisdictions. Grass Valley, Fiber Optic Deployment are trademarks or registered
trademarks of Grass Valley. Belden Inc., Grass Valley, and other parties may also have
trademark rights in other terms used herein.
Terms and Conditions
Please read the following terms and conditions carefully. By using Fiber Optic Deployment
documentation, you agree to the following terms and conditions.
Grass Valley, a Belden Brand (“Grass Valley”) hereby
of Fiber Optic Deployment to use their product manuals for their own internal business use.
Manuals for Grass Valley products may not be reproduced or transmitted in any form or by
any means, electronic or mechanical, including photocopying and recording, for any
purpose unless specifically authorized in writing by Grass Valley.
A Grass Valley manual may have been revised to reflect changes made to the product
during its manufac
product. Care should be taken to ensure that one obtains the proper manual version for a
specific product serial number.
Information in this document is subject to change without
commitment on the part of Grass Valley.
Warranty information is available in the Support section of the Grass Valley Web site
(www.miranda.com).
turing life. Thus, different versions of a manual may exist for any given
Fiber Optics and Fiber Optic Cable are the core technologies at the heart of the equipment.
The Telecast device features the ability to multiplex and de-multiplex a variety of video,
audio and data signals so that they can be carried over a thin strand of Fiber Optic cable for
long distances. The specific theory and operation of Fiber Optics is beyond the scope of
this document.
About Fiber Optics
. . . . . . . . . . . 1
. . . . . . . 2
Product Returns
In the unlikely event of damage to your Fiber Optics during shipping or delivery,take note
of any damage with the delivery or shipping service. If any component does not work
correctly out of the box, contact Grass Valley Support (Contact Us on
If the problem cannot be remedied through a ser
RMA number (Return of Merchandise Authorization). Please note this RMA number inside
and outside of all shipping boxes and on all documentation provided with the items to be
returned.
Fig. 1-1: Single Mode Fiber Optic Cable Cross-Section
page 7).
vice telephone call,you will receive an
1
About Fiber Optics
Safety and Fiber Optic Systems
Safety and Fiber Optic Systems
Optical Fiber Safety
Never look directly into the end of the optic fiber while either end of the system is
operating.
These devices contain CDRH Class 1 laser devices. To prevent damaging your eyes, always
a
void looking directly at, or staring into, the laser light located on an optical connector or
on the end of a fiber.
Infrared radiation is produced at the fiber connection por
the end of any un-terminated optical fibers that are attached to this port. Avoid any direct
exposure to the light that comes from these sources.
Do not power up the unit when no fiber is attached to the fiber port.
There are no manual adjustments to be made in t
type of service to this instrument, other than any as instructed this Guide. Refer all servicing
to Grass Valley (see Contact Us on page 7).
Always use cable connector caps when the cables ar
connector from damage and the unlikely event of exposure to an operating optical link.
Keeping the caps in place when the connectors are not in use will prevent dirt and dust
from entering the connector and degrading the performance of the optical link.
The deployment of Fiber Optic Cables will vary greatly among users. Where the Fiber Optic
cable is permanently installed between units, such as between a campus performance
venue and a central media center, the management of the fiber optic cable will be a onetime occurrence. For those users who deploy the equipment in variable and outside
locations the considerations discussed below are important every time the Fiber Optic
Deployment system is used.
To prevent damaging your eyes, never look directly into the end of the optic fiber
while either end of the system is operating.
Always protect the ST Fiber Optic connectors when the cables are not connected. This
protects the connector from damage and the unlikely event of exposure to an operating
optical link. Keeping protection in place when the connectors are not in use will prevent
dirt and dust from entering the connector and degrading the performance of the optical
link.
It is important that you do an initial setup and test your system as soon as you receive it to
confirm proper operation and to provide training for you and your team prior to an actual
production.
It is highly recommended that you do not attempt to power up the system until all
connections are made. In particular, the Fiber Optic Cable must be connected at both ends.
If you need to power up the Fiber Optic Deployment unit, make sure that the Fiber
Connectors are protected. This will protect theconnector from damage or dirt and protects
you from damaging your eyes.
Deploying the Fiber Cable
Successful connection and management of the Fiber Cable requires you to perform four
tasks:
• Plan the route the Fiber Cable will take to the units
• Run the Fiber Cable along the planned route
• Connect the Fiber Cable Connectors at each end
• Power up the device and check the Fiber Optic Cable Links by means of the LED display
(where applicable).
3
Using Fiber Optic Cable
Planning the Fiber Cable Route
Planning the Fiber Cable Route
Obviously the longer the planned cable run, the more planning required. When planning
your cable route, consider the following:
• Be aware of any possible obstacles that might cause you to run short of cable. You may
need to take a more indirect, but achievable route.
• Be aware of any possible hazards to the cable.
While tactical fiber is extremely durable, it is not immune to damage. For example, you
would not want to run the cable across a lawn scheduled to be cut during your live
production. Make sure the empty roadway at 6am will not be filled with heavy
equipment when it comes time to retrieve your cable.
• Be aware of any possible physical interference with the cable that might cause it to
bend or kink to an extent causes unacceptable signal loss to occur.
• Be aware of any safety hazards.Make sure that the cable will not cause a tripping or
tangling hazard with people, animals, or vehicles.
• Decide whether the Fiber Cable is to be unspooled from the Signal Source of the device
location.
If one end of the cable needs to be moved during the production, it makes sense to
place the spool at that location. Make sure there is enough free cable coming out of
the stationary end of the cable reel to accommodate a well-managed connection to
the first connection.
4
Running the Fiber Cable
Place the stationary
cable connector inside
the center of the reel prior
to unspooling the cable.
Do the following when running your Fiber Cable:
1 Make sure that both ends of the Fiber Cable are securely capped to prevent dirt and
damage
potentially cause you to lose the use of your camera while the problem is being
diagnosed and remedied.
2 If the cable run is long, or if you lose sight of the spooling-out cable reel, make sure you
ha
critical that you receive assistance to prevent the cable end from being caught or
tangled up. Don’t start reeling in the cable on your own and assume the Connector end
will make it back to home base safely.
3 When unspooling the cable, ALWAYS make sure the stationary end is securely
contained within the reel (a loose connector can bang around and be damaged).
NEVER connect the stationary end of the Fiber Cable to the local equipment and then
start unspooling the Fiber Cable. Severe damage to the cable could occur due to
extreme spiraling of the connected portion of the cable.
. ANY dirt in the connector can adversely affect Fiber Optical performance and
ve appropriate assistance in running out the cable. When retrieving the cable, it is
Fiber Optic Deployment
User Guide
Fig. 2-1: Fiber Cable Reel
4 Prior to connecting the Fiber Connectors to the equipment, inspect both the Input and
Output Connectors.
If required, clean with dry compressed air or with
moistened with isopropyl alcohol. Fingerprints or other dirt on the optical connector
end surfaces will reduce the optical signal level on the fiber. If the connectors have
been properly capped during storage and movement, you will not likely have a
problem. However, if a connector has been dropped or dragged through dirt or
exposed to dust, you should cleanthe connector immediately.
5 Once the Fiber Cable has been connected, it is time to secure the Fiber Cable run. Make
e there are no cable hazards in the run. Secure the cable with Cable Guards and/or
sur
Gaffers tape to insure safety.
6 Now the system can be powered on. Plugging in Fiber Cable connectors with the
er on will not damage the system, but is not recommended because of the chance
pow
of possible damaging your eyes.
7 When re-spooling the Fiber Cable, guide it across the entir
winds evenly,reducing the possibility of cinching or kinks.
technical wipes that have been
e width of the spool so that it
5
Using Fiber Optic Cable
Running the Fiber Cable
6
Grass Valley Technical Support
For technical assistance, contact our international support center, at
1-800-547-8949 (US and Canada) or +1 514 333 1772.
To obtain a local phone number for the support center nearest you, please consult the
Contact Us section of Grass Valley’s Web site (
An online form for e-mail contact is also available from the Web site.