Grass Valley ADC-191p User Manual

picoLink Series
ADC-191p
Guide to Installation
and Operation
M825-9800-100
Copyright 2007
Miranda Technologies Inc.
Specifications may be subject to change.
March 2007
Video ADC
Miranda
Technologies inc.
3499 Douglas-B.-Floreani
St-Laurent, Québec, Canada H4S 1Y6
Tel. 514-333-1772
Fax. 514-333-9828
www.miranda.com
ADC-191p
Guide to Installation and Operation
Radio Frequency Interference and Immunity
This unit generates, uses, and can radiate radio frequency energy. If the unit is not properly installed and used in accordance with this guide, it may cause interference with radio communications. Operation with non-certified peripheral devices is likely to result in interference with radio and television reception. This equipment has been tested and complies with the limits in accordance with the specifications in:
FCC Part 15, Subpart B CE EN50081-1:1992 CE EN50082-1:1992.
CONTACT MIRANDA
For technical assistance, please contact the Miranda Technical Support centre nearest you:
Americas
Telephone:
+1-800-224-7882
e-mail:
techsupp@miranda.com
Asia
Telephone:
+81-3-5730-2987
e-mail:
asiatech@miranda.com
Europe, Middle East, Africa, UK
Telephone:
+44 (0) 1491 820222
e-mail:
eurotech@miranda.com
France (only)
Telephone:
+33 (0) 1 55 86 87 88
e-mail:
eurotech@miranda.com
Visit our web site at
www.miranda.com
ADC-191p
Guide to Installation and Operation
CONTENTS
page
1.0 ADC-191p.............................................. 1
1.1 Introduction....................................................1
1.2 Features........................................................1
2.0 Physical Layout.....................................2
3.0 Installation.............................................3
3.1 Power Supply................................................3
3.2 CAV Inputs ..................................................4
3.3 4:2:2 Output...................................................4
4.0 Operation...............................................5
4.1 Switch Settings..............................................5
4.2 Status LED....................................................6
5.0 Specifications........................................7
ADC-191p
Guide to Installation and Operation
ADC-191p
Guide to Installation and Operation
1.0 ADC-191p
1.1 Introduction
The ADC-191p is the industry’s smallest component analog video to 4:2:2 serial digital video ADC. This product automatically detects 525-line and 625-line CAV signals and provides a 4:2:2 serial digital output signal conforming to the SMPTE 259M-C standard. Both SMPTE/EBU and Betacam CAV sources are supported. In addition, this feature-packed unit delivers ease-of-use, a simplified design, easy installation and operation.
Y
B-Y
R-Y
COMPONENT IN
ADC 4:2:2 OUT
Parallel
to serial
Figure 1: ADC-191p functional block diagram
1.2 Features
Automatic 525-line and 625-line format input
detection
Input standards supported: SMPTE/EBU and
Betacam
Time-base corrected and VTR-type sources
supported
Bi-color LED providing error status on input 4:2:2
signal
Very small packaging aluminum extruded body
ADC-191p | 1
Guide to Installation and Operation
2.0 Physical Layout
Figure 2 illustrates the ADC-191p’s major parts and their locations. SMPTE/EBU or Betacam sources are connected to the CAV input BNCs and the 4:2:2 serial digital output is provided by the 4:2:2 output BNC. Error status is provided by the status LED and mode settings are configured by two 3-position slide switches. Finally, the power source is connected to the power connector. .
CAV inputs
3-position slide switches
Status LED
4:2:2 output
Figure 2: Physical layout of the ADC-191p
Power connector
2 | ADC-191p
Guide to Installation and Operation
3.0 Installation
3.1 Power Supply
The power supplies LKS-WSA and LKS-WSE, for 110 V and 220 V operation respectively, are used to power the ADC-191p. Each power supply provides a regulated +5 VDC@750 mA power source. The ADC-191p employs a mini XLR-3 connector for its power needs. Figure 3 provides a detailed pinout of the male connector.
(male connector-facing)
13
Pin 1: Shield Pin 2: GND Pin 3: +5 VDC
2
Figure 3: Power connector pinout
ADC-191p | 3
Guide to Installation and Operation
3.2 CAV Inputs
The CAV inputs consist of green, blue, and red color coded male BNC connectors. Male connectors are provided so as to connect the ADC-191p directly to source equipment. The supported CAV input standards are SMPTE/EBU and Betacam. The Betacam standard can be set with or without setup. The input Y/B-Y/R-Y signals are to be connected to the green, blue, and red BNCs respectively
Refer to section 4.0, Operation in order to select the desired input CAV standard. .
3.3 4:2:2 Output
The 4:2:2 serial digital output signal is provided by the BNC labeled 4:2:2 OUT. The 4:2:2 output signal conforms to the SMPTE 259M-C standard..
4 | ADC-191p
Guide to Installation and Operation
4.0 Operation
4.1 Switch Settings
Figure 4 shows the slide switch locations and functions.
Figure 4: ADC-191p switch settings Input format switch (SW1)
SMPTE: For SMPTE/EBU CAV inputs, set SW1 to
this position. The Y/B-Y/R-Y inputs are to be connected to the green, blue, and red connectors respectively.
BETA 0: For BETA sources with 0 IRE setup, set
SW1 to this position.
BETA 7.5: For BETA sources with 7.5 IRE setup, set
SW1 to this position.
Input stability switch (SW2)
VTR: Set SW2 to VTR if the CAV inputs are VTR-
type or non-time based corrected signals.
Studio: For stable studio CAV sources, set SW2 to
this position.
ADC-191p | 5
Guide to Installation and Operation
4.2 Status LED
The bi-colored status LED is provided to identify any input errors. The following lists the possible situations.
Green: Indicates the ADC-191p is powered and has
detected a valid CAV input signal.
Red: Indicates an error with the input signal has
been detected or simply, there is no input signal installed.
6 | ADC-191p
Guide to Installation and Operation
5.0 Specifications
Input
Signal: Y, B-Y, R-Y 1 Vp-p nominal with sync Return loss: > 35 dB up to 5 MHz Connector: 3 captive cables with 75 Ω male
BNCs
Output
Signal: 4:2:2 SMPTE 259M-C (270 Mbps) Return loss: > 15 dB up to 270 MHz Jitter: < 10 ns p-p Connector : 75 Ω BNC
Processing performance
Signal path: 10 bits Quantization: 12 bits Freq. response: ±0.5 dB to 5 MHz Processing delay: 3 lines
Electrical
Voltage requirement: +5 VDC Power consumption: <3 W Power connector: Mini XLR-3
Mechanical
Overall size: 102 mm x 25 mm x 18 mm (4” x 1” x 0.7”) Power cable length: 127 mm (5”) Full spec. temp. range: 0° C (32° F) to 30° C (86° F)
ADC-191p | 7
Loading...