GRAPHTEC Craft ROBO, CC100-20 Quick Start Instructions

How to Connect the Power Cable
G
Main unit (the Craft ROBO)
G
Quick Start Instruction Sheet (this sheet) …1 copy
G
AC adapter …1
G
Power cable …1
G
Cutter plunger
G
Blade adjustment cap …2
G
Standoff ring …1
G
Ball-point pen plunger …1
G
Media Trial Kit …1 pack
G
Craft ROBO
Software Package CD-ROM …1
G
Quick Application Guide …1 copy
G
USB cable …1
First of all
Setup of the Craft ROBO main unit is now complete. Use the Media Trial Kit to learn basic methods of using the Craft ROBO.
Quick Start Instructions
Setup Instruction Sheet for the Craft ROBO (CC100-20)
Check
All the Included Items
Install
the Software
Connect
the Craft ROBO to a PC
STEP
1
STEP
2
STEP
3
Thank you for purchasing the Graphtec Craft ROBO. This quick start instruction sheet outlines the procedure for setting up your machine. After setup, refer to the “Quick Application Guide” included with the Craft ROBO to learn how to use it. The user’s manuals for the main unit and software are available in PDF format on the CD-ROM supplied with the Craft ROBO. Refer to these manuals for details on the Craft ROBO functions.
(2)
(1)
(3)
Do not insert the USB cable yet.
1. Check that the Craft ROBO is not connected to your computer. Start Windows, and then insert the CD-ROM included with your Craft ROBO into the CD drive of your computer.
If you are using the Craft ROBO for the first time
The preparations are now complete
If you are performing installation for
the second or a subsequent time
4. If the following message is displayed, use the USB cable to connect the Craft ROBO to your computer. A wizard and the Help menu will be displayed. Follow the instructions to complete the setup.
The ROBO Master software is installed when you set up the Craft ROBO. This software will help you to create stickers, cut text on vinyl film, or create pop-up greeting cards. Use this software as an introduction to cutting stickers and signs, or making paper crafts.
When the software installation has been completed, it may be necessary to reboot Windows. In this case, follow the instructions for rebooting. After rebooting, and when the USB cable is used to connect the Craft ROBO to your computer, Windows will automatically recognize the Craft ROBO. If the “Search for New Hardware” wizard is displayed, select “Install the software automatically (Recommended)”.
2. The Craft ROBO Start window is displayed after a short interval.
If it is not displayed, select “Specify File Name to Execute” from the Windows Start menu, execute the MultiSetup.exe program on the CD­ROM, and then click the OK button.
3. Click “Setup Craft ROBO” in the Craft ROBO Start window to launch the installer. All the required software will be successively installed by “Setup Craft ROBO”. Follow the displayed screens to complete the installation.
Click here
MultiSetup.exe
5. This completes the installation of the software. You can now start using your Craft ROBO. Close the Craft ROBO Start window.
This product comes with the following standard items. Referring to this list, check to confirm that all the items are included.
Referring to the diagram shown below, connect the power cable to your machine in the sequence (1) to (3).
621249110
22
11
Mounting the Cutter Plunger
Mounting the Ball-point Pen
Operation Manual
Note before using
Sheet Width: 210 mm up to a maximum of 260 mm
Cutting Width:
190 mm (max. 200 mm)
Cutter plunger
Blade adjustment cap
Blue (0.1 mm) Thin film Yellow (0.2 mm) Thick film, thin paper Red (0.3 mm) Thick paper such as a postcard
Cutter blade
Standoff ring
Align the sheet with the guide line
OPEN
OPEN :
Unlock
CLOSE:
Lock
CLOSE
LOCK LEVER
Ball-point pen plunger
Align with the notch
Loosen
Tighten
LED lamp
Standby switch
Peel off this part prior to use.
Adhesive
Protective liner
Paper backing



Caution:
Be particularly careful with the cutter blade when changing the blade adjustment cap or attaching the cutter plunger to the Craft ROBO.
NOTE:
Graphtec does not guarantee the cutting quality when non-genuine Craft ROBO media is used. Using non-standard media may void the warranty.
When using a ball-point pen, be sure to use a narrow one. In addition, confirm that the tip of the pen protrudes 3 to
3.5 mm from the ball­point pen plunger. Please refer to the Craft ROBO User’s Manual (CD­ROM) for further details on the ball-point pen types that can be used.
When loading an A4-size sheet, align it with the guide line.
To cut regular A4-size media, peel off the protective liner from both edges of the carrier sheet prior to use.
The standoff ring should be used when cutting a sheet that has been affixed to the carrier sheet.
Media Type selected to be cut
The most suitable cap color for the selected Media Type is displayed
Learn how to use it with the Media Trial Kit.
The Craft ROBO has the two functions shown below. Use them as required.
Load a Sheet for Cutting or Check Plotting
Confirm that you have the following items supplied with your Craft ROBO.
While making sure that the sheet is straight, align it with the guide line.
Turn the feed knob counterclockwise to feed the sheet. Continue feeding the sheet until its top edge is aligned with the cutting mat as shown below.
Notes on Loading Media in the Craft ROBO
To cut a sheet smaller than A4 size or a sheet without a protective liner, affix it to the carrier sheet included with the Craft ROBO before performing cutting.
Press the standby switch, and confirm that the LED lamp lights.
Note: Turn the feed knob to remove the sheet.
When cutting has been completed, press the standby switch and confirm that the LED lamp goes out.
Referring to the figure shown below, mount a ball­point pen in the Craft ROBO. When using a ball­point pen, select “Pen” for “Media Type” in the Craft ROBO Controller.
Referring to the figure shown below, firmly mount the cutter plunger in the Craft ROBO.
The most suitable blade adjustment cap is automatically displayed when the Media Type is selected in the Craft ROBO Controller.
Attach a blade adjustment cap.
Insert firmly into position until this surface contacts the plunger holder.
Load a sheet in the Craft ROBO
Do not load media without a protective liner, or perform a cutting operation when there is no media loaded, as this will damage the cutting mat.
Feed knob
Cutting mat
Turn the feed knob until the sheet reaches the edge of the cutting mat.
Setup is complete
621249110
Loading...