Grand Hall is the expert on this product and
trained to help you with:
Assembly Questions
Ÿ
Grill Operation
Ÿ
Replacement of Damaged or Missing parts
Ÿ
visit www.grandhall.com or call:
1-877-934-7455
Monday - Friday 8:00am-4:30pm CST
IMPORTANT:
NOTE TO ASSEMBLER / INSTALLER:
Ÿ
Leave this manual with the consumer.
NOTE TO CONSUMER:
Ÿ
Keep this manual for future reference.
RECORD YOUR SERIAL # __________________
Ÿ
(see silver CSA label on main body of grill)
OD3208ALP/NG & OD3208BLP/NG
!!
Failure to comply with these instructions could
Ÿ
result in a fire or explosion that could cause
serious bodily injury, death or property damage.
Whether this grill was assembled by you or
Ÿ
someone else, you must read this entire manual
before using your grill to ensure the grill is
properly assembled, installed and maintained.
Use your grill at least 3 feet away from any
Ÿ
wall or surface. Use your grill at least 3 feet
away from combustible objects that can melt or
catch fire such as vinyl or wood siding, fences
and overhangs or sources of ignition including
pilot lights on water heaters and live electrical
appliances.
THIS GAS APPLIANCE IS DESIGNED FOR
Ÿ
OUTDOOR USE ONLY.
Never use your gas grill in a garage, porch,
Ÿ
shed, breezeway or any other enclosed area.
Never obstruct the flow of ventilation air
Ÿ
around your gas grill housing.
Ÿ
Never disconnect the gas regulator or any
gas fitting while your grill is lit. A lit grill can ignite
leaking gas and cause a fire or explosion which
could result in property damage, personal injury
or death.
Registered and unregistered Trademarks held by
Grand Hall include the following:
Grand Hall and design®, DS Grill and design®,
Crossray™ Lateral Infrared Burner Technology, Command Flame®, Smooth Start® Electronic Ignition System,
Ceramic Savor Plates®, Sear-zzler®, Stainless Clad
Therma-Core® Cooking Grids, Grand Café and design®,
Grand Mark and design®, Grand Chef and design®,
Grand Royale and design®, Globe Café and design®,
Urban Café and design®, Smokeless Grill and design®.
Patents held by Grand Hall include the following:
The Crossray Burner System by Grand Hall is covered
by Australian Patent No. 2006100635, Chinese Patent No.
960361, European Patent Pending, French Patent
0607231, German Patent No. 20 2006 012 212.5, U.K
flammable liquids or vapors in the vicinity of this or any other appliances.
An LP cylinder not connected for use
2.
shall not be stored in the vicinity of
this or any other appliance.
!!
LPG models must be used with Liquid Propane Gas
•
and the regulator assembly supplied. Natural Gas
models must be used with Natural Gas only. Any
attempt to convert the grill from one fuel type to
another is extremely hazardous and will void the
warranty.
Keep gas regulator hose away from hot grill
•
surfaces and dripping grease. Avoid unnecessary
twisting of hose. Visually inspect hose prior to
each use for cuts, cracks, excessive wear or other
damage. If the hose appears damaged do not use
the gas grill. Call 1-877-934-7455 for a certified
replacement hose.
California Proposition 65
•
Combustion byproducts produced when using this
product contain chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
Brass components on the grill, such as hose fittings,
propane cylinder valves (sold separately) and burner
valve stems, contain lead which is known to the State
of California to cause cancer, birth defects, or other
reproductive harm.
WARNING
!!
•
This appliance, when installed, must be electrically grounded in accordance with local codes
or, in the absence of local codes, with the
National Electrical Code, ANSI/NFPA 70, or the
Canadian Electrical Code, CSA C22.1.
•
Keep any electrical supply cord and the fuel
supply hose away from any heated surfaces.
WARNING
Never use charcoal or lighter fluid in this gas grill.
•
Failure to comply with these instructions could result in
a grease fire or explosion that could cause serious
bodily injury, death or property damage.
The Grease Draining Tray must be visually inspected
•
before each grill use. Remove any grease and wash
Grease Draining Tray and Grease Receptacle with a
mild soap and warm water solution. Failure to comply
with these instructions could result in a grease
fire or explosion that could cause serious bodily
injury, death or property damage.
!
If you smell gas:
Shut off gas to the appliance.
1.
Extinguish any open flame.
2.
Open lid.
3.
If odor continues, keep away from the
4.
appliance and immediately call your
gas supplier or your fire department.
2
DANGER
!
Pre-Assembly Instructions For Your Safety
Congratulations on your selection of one of the finest outdoor
kitchen appliances available. Your Grill is equipped with the
unique Crossray Infrared Cooking System® by Grand Hall,
which offers restaurant style grilling performance.
Infrared grilling technology cooks the food directly (and not
the air around it) which offers many advantages over conven-
tional grilling systems:
MORE FLAVORFUL FOOD as the intense heat sears the
food and locks in the juices while also cooking it faster
which usually means more succulence.
FEWER FLAREUPS as the higher infrared heat vaporizes more drippings which also adds natural flavoring to
your food.
MORE EFFICIENCY AND CONVENIENCE as the higher
heat means shorter cooking times, more fuel efficiency
and easier year round grilling.
To begin your “restaurant quality” grilling, become familiar with
all of the cooking elements of your Grand Hall Grill lighting and
operating instructions.
US Patented No.: 7,475,632
Europe Patent Pending
Australia Patent No.: 2006100635
Germany Patent No.: 202006012212.5
France Patent No.: 0607231
UK Patent No.: GB2440714
China Patent No.: 960361
PRE-ASSEMBLY
Read and perform the following pre-assembly instructions:
Tools Required for Assembly:
Protective work gloves
•
Protective eyewear
•
Phillips Head Screwdriver
•
You will need assistance from another person to
handle the grill head and other large, heavy parts.
Open lid of shipping carton. Remove top sheet of cardboard and packing materials. Lay cardboard sheet on
floor and use as a work surface to protect floor and
grill parts from scratches.
You may slice the carton front corners with a utility
knife to lay open the carton front panel. This allows
you to raise the Lid and remove the components
packed inside, making it easier to lift.
Use the Hardware and Part Diagrams to ensure all
items are included and free of damage.
Do not assemble or operate the grill if it appears damaged. If there are damaged or missing parts when
you unpack the shipping box or you have questions
during the assembly process call 1-877-934-7455 M-
F 8AM-4:30PM CST for assistance.
Grill Installation Codes
The installation must conform with local codes or, in the
absence of local codes, with either the National Fuel Gas
Code, ANSI Z223.1/NFPA 54, Natural Gas and Propance
Installation Code, CSA B149.1, or Propane Storage and
Handling Code, B149.2.
CSA Label located
on the inside panel
of the left door
3
Hardware Pack Parts List for Models OD2608ALP/NG & OD2608BLP/NG
PART #PART DESCRIPTIONQTYPURPOSE OF PART
P06030002A Hardware Pack 1For use in assembly of Models OD2608ALP & OD2608BLP
P06030005A Hardware Pack 1For use in assembly of Models OD2608ANG & OD2608BNG
S182G0406A
S182G0306A
S182G0306A
S182G0306A
S182G0406A
S182G03061
S182G0306A
S182G0306A
S182G0306A
P05515130L Wrench1 Install Casters
S182G0316A
S182G0306A
S182G0306APan Head Screw 3/16"x3/8"4 Install Cart Front Bracket
S182G0306A
S182G0316A
S182G0306A
S182G03081
Pan Head Screw 1/4"x3/8" 4
Install Caster Seats to the Cart Side Panels
Pan Head Screw 3/16"x3/8"8
Pan Head Screw 3/16"x3/8"4 Install Cart Side Panels to Cart Bottom Panel
Pan Head Screw 3/16"x3/8"4 Install Lower Door Hinge Brackets
Pan Head Screw 1/4"x3/8" 8Install Caster Seats to the Cart Bottom Panel
Pan Head Screw 3/16"x3/8"2 Install Door Guide Plate
Pan Head Screw 3/16"x3/8"6 Install Cart Rear Panel
Pan Head Screw 3/16"x3/8"6 Install Cart Top Panel
Pan Head Screw 3/16"x3/8"8 Install Tank Holder Assembly (For OD2608ALP & OD2608BLP models)
Pan Head Screw 3/16"x1"4 Install Grill Bowl
Pan Head Screw 3/16"x3/8"
2 Install the Control Box
Pan Head Screw 3/16"x3/8"8 Install Top Door Hinge Brackets
Pan Head Screw 3/16"x1"8 Install Side Shelf Brackets
Pan Head Screw 3/16"x3/8"8
Install Side Shelves
Pan Head Screw 3/16"x1/2"2
Hardware Pack Diagram List for Models OD2608ALP/NG & OD2608BLP/NG
Pan Head Screw 1/4"x3/8"
Qty. 12
Part # S182G0406A
Pan Head Screw 3/16"x1/2"
Qty. 2
Part # S182G03081
Pan Head Screw 3/16"x3/8"
Qty. 50 (NG models)
Qty. 58 (LPG models)
Part # S182G0306A
Pan Head Screw 3/16"x3/8"
Qty. 2
Part # S182G03061
Pan Head Screw 3/16"x1"
Qty. 12
Part # S182G0316A
Wrench
Qty. 1
Part # P05515130L
* One Battery/AA and Four Batteries/AAA included in the Hardware Pack.
4
Hardware Pack Parts List for Models OD3208ALP/NG & OD3208BLP/NG
PART #PART DESCRIPTIONQTYPURPOSE OF PART
P06030004A Hardware Pack 1 For use in assembly of Models OD3208ALP & OD3208BLP
P06030006A Hardware Pack 1 For use in assembly of Models OD3208ANG & OD3208BNG
S182G0406A
S182G0306A
S182G0306A
S182G0306A
S182G0406A
S182G03061
S182G0306A
S182G0306A
S182G0306A
P05515130L Wrench1 Install Casters
S182G03081
S182G0316A
S182G0306A
S182G0306APan Head Screw 3/16"x3/8" 4 Install Cart Front Bracket
S182G0306A
S182G0316A
S182G0306A
S182G03081
Pan Head Screw 1/4"x3/8" 4
Install Caster Seats to the Cart Side Panels
Pan Head Screw 3/16"x3/8" 8
Pan Head Screw 3/16"x3/8" 4 Install Cart Side Panels to Cart Bottom Panel
Pan Head Screw 3/16"x3/8" 4 Install Lower Door Hinge Brackets
Pan Head Screw 1/4"x3/8" 8 Install Caster Seats to the Cart Bottom Panel
Pan Head Screw 3/16"x3/8" 2 Install Door Guide Plate
Pan Head Screw 3/16"x3/8" 6 Install Cart Rear Panel
Pan Head Screw 3/16"x3/8" 6 Install Cart Top Panel
Pan Head Screw 3/16"x3/8" 8 Install Tank Holder Assembly (For OD3208ALP & OD3208BLP models)
Pan Head Screw 3/16"x1/2" 4 Install Spice Shelf
Pan Head Screw 3/16"x1"4 Install Grill Bowl
Pan Head Screw 3/16"x3/8"
2 Install the Control Box
Pan Head Screw 3/16"x3/8" 8 Install Top Door Hinge Brackets
Pan Head Screw 3/16"x1"8 Install Side Shelf Brackets
Pan Head Screw 3/16"x3/8" 8
Install Side Shelves
Pan Head Screw 3/16"x1/2" 2
Hardware Pack Diagram List for Models OD3208ALP/NG & OD3208BLP/NG
Pan Head Screw 1/4"x3/8"
Qty. 12
Part # S182G0406A
Pan Head Screw 3/16"x1/2"
Qty. 6
Part # S182G03081
Pan Head Screw 3/16"x3/8"
Qty. 50 (NG models)
Qty. 58 (LPG models)
Part # S182G0306A
Pan Head Screw 3/16"x3/8"
Qty. 2
Part # S182G03061
Pan Head Screw 3/16"x1"
Qty. 12
Part # S182G0316A
Wrench
Qty. 1
Part # P05515130L
* One Battery/AA and Four Batteries/AAA included in the Hardware Pack.
5
Parts Diagram for Models OD2608ALP/NG & OD2608BLP/NG
Extension Fitting for Manifold With Orifice (LPG)P06539030AP06539030A2
24
Extension Fitting for Manifold With Orifice (NG)P06539031AP06539031A2
25BowlP0071368JAP0071368JA1
26Thermocouple ProtectorP03343019CP03343019C2
27Thermocouple Bracket, RearP03327082CP03327082C1
28Thermocouple BracketP03327083CP03327083C1
29AElectrode, FrontP02618050AP02618050A1
29BElectrode, RearP02618051AP02618051A1
30AThermocouple for LED Light, RearP05305065BP05305065B1
30BThermocouple for LED Light, FrontP05305066BP05305066B1
31AThermocouple for Gas Valve, RearP05305061BP05305061B1
31BThermocouple for Gas Valve, FrontP05305055BP05305055B1
32Bowl Front Trim Plate AssemblyP02913471SP02913471S1
33Control Panel Heat Shield BracketP0300613FDP0300613FD1
34Control Panel Heat Shield P03007206BP03007206B1
Gas Valve/Manifold Assembly (LPG)Y0060677Y00606771
35
Gas Valve/Manifold Assembly (NG)Y0060678Y00606781
36Electric Ignitor, 2-PortP02502352CP02502352C1
37LED Light with Wire - AP02615159AP02615159A1
38LED Light with Wire - BP02615167AP02615167A1
39Control PanelP02913464XP02913464X1
40Control Knob SeatP03439014AP03439014A2
41Control KnobP03436053VP03436053V2
42Grease Draining TrayP02717615BP02717615B1
42AHandle for Grease Draining TrayP00213032HP00213032H1
61Caster Seat, Left Front & Right RearP05327064HP05327064H2
62Caster Seat, Right Front & Left RearP05327065HP05327065H2
63Door Assembly, LeftP04305062BP04305062Q1
64Door Assembly, RightP04306032BP04306032Q1
65Door HingeY0550002Y05500022
66Door MagnetP05523056LP05523056L4
67Door Guide PlateP05510137AP05510137A1
68Caster, 3" without BrakeP05112026AP05112026A2
69Caster, 3" with BrakeP05112027AP05112027A2
70Tank Holder Bracket (LPG)P04009035CP04009035C2
71Tank Holder (LPG)P05359003GP05359003G1
72Tank Fastening Strap (LPG)P05314002VP05314002V1
73Side Shelf, LeftP01102057DP01102057D1
74Side Shelf, RightP01103047DP01103047D1
75Side Shelf Trim Plate, LeftP07503023AP07503023A1
Extension Fitting for Manifold with Orifice (LPG)P06539032AP06539032A4
25
Extension Fitting for Manifold with Orifice (NG)P06539033AP06539033A4
26Cross Lighting ChannelP02212377AP02212377A2
27Lid Hinge with NutP05501136LP05501136L2
28Thermocouple ProtectorP03343017CP03343017C4
29Thermocouple Bracket, Left Front/Right RearP03327082CP03327082C2
30Thermocouple Bracket, Right Front/Left RearP03327083CP03327083C2
31Thermocouple for Gas ValveP05305054BP05305054B2
32Thermocouple for Gas ValveP05305055BP05305055B2
33AThermocouple for LED Light, Left FrontP05305056BP05305056B1
33BThermocouple for LED Light, Left RearP05305057BP05305057B1
33CThermocouple for LED Light, Right FrontP05305058BP05305058B1
33DThermocouple for LED Light, Right RearP05305059BP05305059B1
34AElectrode, Left FrontP02618046AP02618046A1
34BElectrode, Left RearP02618047AP02618047A1
34CElectrode, Right FrontP02618048AP02618048A1
34DElectrode, Right RearP02618049AP02618049A1