Page 1
Trabon® MJ Series-Flo
Divider Valves
DESCRIPTION
Trabon MJ Series-Flo Divider Valves are designed for lubricating
systems serving machine tools and other comparable equipment.
In many installations the MSP divider valve serves as the Master
divider assembly for an MJ system.
A typical MJ Series-Flo divider assembly (to the right) consists of
an inlet section, end section and three to eight valve sections. One
manifold will serve up to a maximum of 16 lube points.
The MJ valve sections, which have built-in outlet check valves,
are available in various output sizes. Each twin (T) section has 2
outlets, one from each side of the section. Each single (S) section
can have an outlet on either side but the outlet on one side must be
plugged
for the section to operate properly.
FEATURES/ADVANTAGES
Delivers metered amount of lubricant•
Compact design•
Simple to install•
Built-in outlet check valves•
OPERATION
Operational sequence of an MJ Series-Flo divider valve assembly
is defined as “progressive”. The term progressive means that
each valve section completes its piston stroke, discharging a
measured amount of lubricant to the bearing it serves before the
following valve section operates. As long as lubricant is supplied
under pressure to the inlet section of the divider assembly, valve
sections will continue to operate in a progressive manner. Divider
assemblies always follow a constant discharge pattern. Whenever
lubricant flow ceases, the valving pistons will stop. When flow
resumes it will start again at the same point in the discharge cycle.
SPECIFICATION
Material Plated Steel
Pressure (max) 2,000 psi (137.89 bar)
Lubricant Oil or Grease up to NLGI Grade 1
Max Operating Temperature 200ºF (93ºC)
Max Cycle Rate w/Cycle Pin 60 cycles/min.
Torque:
Tie Rod Nut 12 ft lbs
Enclosure Plug 11-13 ft lbs
Outlet Port Plug 6-7 ft lbs
ORDERING INFORMATION - VALVE SECTIONS
Description Part No. Old Part No.
5S, 0.010 cu.in. (0.163 cu.cm3)* 562500 001-005-001
5T, 0.005 cu.in. (0.081 cu.cm
10S, 0.020 cu.in. (0.327 cu.cm
10T, 0.010 cu.in. (0.163 cu.cm
10S w/Cycle Indicator - RH, 0.020 cu.in. (0.327 cu.cm
10T w/Cycle Indicator - RH, 0.010 cu.in. (0.163 cu.cm
10S w/Cycle Indicator - LH, 0.020 cu.in. (0.327 cu.cm
10T w/Cycle Indicator - LH, 0.010 cu.in. (0.163 cu.cm
15S, 0.030 cu.in. (0.491 cu.cm
15T, 0.015 cu.in. (0.245 cu.cm
15S w/Cycle Indicator - RH, 0.030 cu.in. (0.491 cu.cm
15T w/Cycle Indicator - RH, 0.015 cu.in. (0.245 cu.cm
15S w/Cycle Indicator - LH, 0.030 cu.in. (0.491 cu.cm
15T w/Cycle Indicator - LH, 0.015 cu.in. (0.245 cu.cm
Inlet 560643 510-992-002
End 560645 510-994-002
3 Section Tie Rod 557515 510-999-030
4 Section Tie Rod 557516 510-999-040
5 Section Tie Rod 557517 510-999-050
6 Section Tie Rod 557518 510-999-060
7 Section Tie Rod 557519 510-999-070
8 Section Tie Rod 557520 510-999-080
Nut for Tie Rod 556371 410-440-010
*Includes one gasket.
Note: The valve size is stamped on each valve section. The volume discharge per
outlet after a complete cycle is indicated by cu.in. (cu.cm
3
)* 562503 001-005-002
3
)* 562501 001-010-001
3
)* 562504 001-010-002
3
)* 562508 001-010-601
3
)* 562510 001-010-602
3
)* 562512 001-010-611
3
)* 562513 001-010-612
3
)* 562502 001-015-001
3
)* 562505 001-015-002
3
)* 562509 001-015-601
3
)* 562511 001-015-602
3
)* – 001-015-611
3
)* 564205 001-015-612
3
)
Page 2
3.23
(82.2)
1.06
(26.9)
.750
(19.0)
CYCLE PIN INDICATOR
1/8 NPSF
LUBE INLET
1/8 NPSF
INDICATOR OUTLET
.750
(19.0)
1.37
(34.9)
1.09
(27.7)
7/32 DIA. (5.54)
4 MTG. HOLES
.270 (6.8)
.858
(21.79)
1/8 NPSF
LUBE
OUTLET
B
.250
(6.3)
.582 TYPICAL
(14.7)
2.54
(64.5)
2.12
(53.9)
.687
(17.4)
A
ORDERING INFORMATION - ASSEMBLIES
DIMENSIONS Inches/(mm) & WEIGHT
Note: Millimeter dimensions appear in parentheses below decimal
figure in inches.
Divider Valves Sketch Example
MJ-3-10C-05TCR-15T
MJ-3 Divider Valve with Indicator
and Internal Crossport
Inlet
Plugged— 10S — Open
Open— 5T CR — Plugged
Open— 15T — Open
End
➤
MJ - X - X - XX - X - XX
MANIFOLD OPTIONS
P - INSTALLATION OF PERFORMANCE
INDICATORS IN ALL WORKING OUTLETS
NUMBER OF SECTIONS
3 - THREE
4 - FOUR
5 - FIVE
6 - SIX
7 - SEVEN
8 - EIGHT
SECTION CAPACITY
05 - .005 cu.in. (SEE NOTE 8)
10 - .010 cu.in.
15 - .015 cu.in.
TYPE OF VALVE BLOCK
T - TWIN STANDARD
S - SINGLE STANDARD - RH OUTLET
L - SINGLE STANDARD - LH OUTLET
B - TWIN W/CYCLE PIN RIGHT SIDE
C - SINGLE W/CYCLE PIN RIGHT SIDE - RH OUTLET
D - SINGLE W/CYCLE PIN RIGHT SIDE - LH OUTLET
E - TWIN W/CYCLE PIN LEFT SIDE
F - SINGLE W/CYCLE PIN LEFT SIDE - RH OUTLET
G - SINGLE W/CYCLE PIN LEFT SIDE - LH OUTLET
*CROSSPORTING OPTION
CR - RIGHT HAND SIDE
CL - LEFT HAND SIDE
CB - BOTH SIDES
*OMIT WHEN NOT REQUIRED
NOTES:
Capacity sections are specified starting from inlet section, and must equal number 1.
of sections specified
When a capacity section is crossported, its outlet is plugged and output is diverted 2.
to the next valve farthest from inlet
Last capacity section, farthest from the inlet, cannot be crossported3.
Singled capacity section can be crossported on one side only4.
When capacity section is singled, the outlet not being used is plugged5.
Internal crossporting can be supplied on a capacity section only when supplied on a 6.
manifold assembly (if supplied as a loose unit, it can be field drilled only)
External singling and crossporting bars are available for field installation7.
Cycle Indicator Pin is not available on 0.005 capacity section8.
Indicate crossport option after capacity section if required, omit if not required9.
Divider systems should be limited to first and second stages only. 10. Third staging
is not recommended. Refer to bulletins L20101, L20105, and L20115 for further
information on system design
ORDERING INFORMATION
Description Part No. Old Part No.
Cycle Indicator Repair Kit 563948 560-002-987
Replacement Gasket 557514 510-998-002
Cycle Switch (SPDT) & Bracket 563272 510-599-000
Cycle Switch (DPDT) & Bracket 564357 510-577-000
Singling Bars 562915 189-000-050
Crossporting Bars 562914 189-000-040
Divider Valve Installation Accessories Bulletin L15126
Performance Indicators Bulletin L15401
Additional Accessories & Parts Bulletin L10161
All written and visual data contained in this document are based on the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice.
Contact us today!
To receive product information or talk with a Graco representative,
call 800-533-9655 or visit us online at www.graco.com.
©2006-2009 Graco Inc. Form No. L10111 Rev. B 1/09 Printed in U.S.A. All other brand names or marks are used for identification purposes and are trademarks of their respective owners. All written and
visual data contained in this document are based on the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice.
Loading...